summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/realtek/rtw88/mac.c
AgeCommit message (Collapse)Author
2019-09-24rtw88: configure firmware after HCI startedYan-Hsuan Chuang
After firmware has been downloaded, driver should send some information to it through H2C commands. Those H2C commands are transmitted through TX path. But before HCI has been started, the TX path is not working completely. Such as PCI interfaces, the interrupts are not enabled, hence TX interrupts will not be issued after H2C skb has been DMAed to the device. And the H2C skbs will not be released until the device is powered off. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-25rtw88: power on again if it was already onYan-Hsuan Chuang
We could fail to power on because it was already on. If the return value is -EALREADY, power off and then power on again to turn on the hardware as expected. Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-04-30rtw88: new Realtek 802.11ac driverYan-Hsuan Chuang
This is a new mac80211 driver for Realtek 802.11ac wireless network chips. rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode functionalities. The firmware for both can be found at linux-firmware. https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git For RTL8822BE: rtw88/rtw8822b_fw.bin For RTL8822CE: rtw88/rtw8822c_fw.bin And for now, only PCI buses (RTL8xxxE) are supported. We will add support for USB and SDIO in the future. The bus interface abstraction can be seen in this driver such as hci.h. Most of the hardware setting are the same except for some TRX path or probing setup should be separated. Supported: * Basic STA/AP/ADHOC mode, and TDLS (STA is well tested) Missing feature: * WOW/PNO * USB & SDIO bus (such as RTL8xxxU/RTL8xxxS) * BT coexistence (8822B/8822C are combo ICs) * Multiple interfaces (for now single STA is better supported) * Dynamic hardware calibrations (to improve/stabilize performance) Potential problems: * static calibration spends too much time, and it is painful for driver to leave IDLE state. And slows down associate process. But reload function are under development, will be added soon! * TRX statictics misleading, as we are not reporting status correctly, or say, not reporting for "every" packet. The next patch set should have BT coexistence code since RTL8822B/C are combo ICs, and the driver for BT can be found after Linux Kernel v4.20. So it is better to add it first to make WiFi + BT work concurrently. Although now rtw88 is simple but we are developing more features for it. Even we want to add support for more chips such as RTL8821C/RTL8814B. Finally, rtw88 has many authors, listed alphabetically: Ping-Ke Shih <pkshih@realtek.com> Tzu-En Huang <tehuang@realtek.com> Yan-Hsuan Chuang <yhchuang@realtek.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Tested-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>