summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/mediatek/mt7601u
AgeCommit message (Collapse)Author
2018-03-27wireless: Use octal not symbolic permissionsJoe Perches
Prefer the direct use of octal for permissions. Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace and some typing. Miscellanea: o Whitespace neatening around these conversions. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-22mt7601u: use firmware_request_cache() to address cache on rebootLuis R. Rodriguez
request_firmware_cache() will ensure the firmware is available on resume from suspend if on reboot the device retains the firmware. This optimization is in place given otherwise on reboot we have to reload the firmware, the opmization saves us about max 1s, minimum 10ms. Cantabile has reported back this fixes his woes with both suspend and hibernation. Reported-by: Cantabile <cantabile.desu@gmail.com> Tested-by: Cantabile <cantabile.desu@gmail.com> Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-13mt7601u: let mac80211 validate rx CCMP PNLorenzo Bianconi
Apparently the hardware does not perform CCMP PN validation so let mac80211 take care of possible replay attacks in sw. Moreover indicate ICV and MIC had been stripped setting corresponding bits in ieee80211_rx_status. The fix has been validated using 4.2.1 and 4.1.3 tests from the WiFi Alliance vulnerability detection tool. Fixes: c869f77d6abb ("add mt7601u driver") Acked-by: Jakub Kicinski <kubakici@wp.pl> Tested-by: David Park <david.park@hitemengineering.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-13mt7601u: simplify mt7601u_mcu_msg_alloc signatureLorenzo Bianconi
Remove mt7601u_dev parameter from mt7601u_mcu_msg_alloc signature since dev pointer is never used in routine body Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-13mt7601u: remove a warning in mt7601u_efuse_physical_size_check()Lorenzo Bianconi
Fix the following sparse warning in mt7601u_efuse_physical_size_check: - drivers/net/wireless/mediatek/mt7601u/eeprom.c:77:27: warning: Variable length array is used Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-28mt7601u: make write with mask access atomicLorenzo Bianconi
Introduce __mt7601u_rr and __mt7601u_vendor_single_wr routines in order to make mt7601u_rmw and mt7601u_rmc atomic. This patch does not fix a reported issue but makes the usb access more robust to concurrent operations on the same register since it is theoretically possible that read and write accesses of mt7601u_rmw/mt7601u_rmc can be interleaved with a different write operation on the same register. Moreover using __mt7601u_rr and __mt7601u_vendor_single_wr in mt7601u_rmw/mt7601u_rmc allows to grab vendor_req_mutex mutex once instead of twice Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-28mt7601u: set device mac address in mt7601u_add_interface()Lorenzo Bianconi
If mac80211 adds a vif with a different mac address respect to the eeprom one, the device will not be able to connect to the ap since the hw address has not been updated. Fix the issue updating hw mac address in mt7601u_add_interface routine BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1516935 Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-28mt7601u: move mt7601u_set_macaddr in mac related codeLorenzo Bianconi
Remove static qualifier from mt7601u_set_macaddr routine and move it in mac related code in order to be used to properly support vif with different mac address respect to the default one Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-08-24mt7601u: check memory allocation failureChristophe Jaillet
Check memory allocation failure and return -ENOMEM in such a case, as already done a few lines below. As 'dev->tx_q' can be NULL, we also need to check for that in 'mt7601u_free_tx()', and return early. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-08-10mt7601u: constify usb_device_idArvind Yadav
usb_device_id are not supposed to change at runtime. All functions working with usb_device_id provided by <linux/usb.h> work with const usb_device_id. So mark the non-const structs as const. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: introduce and use skb_put_data()Johannes Berg
A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-28Merge tag 'mac80211-next-for-davem-2017-04-28' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Another set of patches for -next: * API support for concurrent scheduled scan requests * API changes for roaming reporting * BSS max idle support in mac80211 * API changes for TX status reporting in mac80211 * API changes for RX rate reporting in mac80211 * rewrite monitor logic to prepare for BPF filters * bugfix for rare devices without 2.4 GHz support * a bugfix for recent DFS changes * some further cleanups The API changes are actually at a nice time, since it's typically quiet just before the merge window, and trees can be synchronized easily during it. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-26mt7601u: check return value of alloc_skbPan Bian
Function alloc_skb() will return a NULL pointer if there is no enough memory. However, in function mt7601u_mcu_msg_alloc(), its return value is not validated before it is used. This patch fixes it. Signed-off-by: Pan Bian <bianpan2016@163.com> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-03-06wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple driversAndrew Zaborowski
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature wholesale in all mac80211-based drivers that do not set the IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and will detect when the thresholds set by ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few) drivers need code to enable the firmware to monitor the thresholds. This is mostly only compile-tested. Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-12-16Makefile: drop -D__CHECK_ENDIAN__ from cflagsMichael S. Tsirkin
That's the default now, no need for makefiles to set it. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
2016-11-29mt7601u: wait for clear rxq when stopping macAnthony Romano
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty but instead continues polling after the rxq status stays clear; bringing down the interface takes about six seconds from this alone. Speed up path by exiting rxq loop once status repeatedly polls empty. Signed-off-by: Anthony Romano <anthony.romano@coreos.com> Reviewed-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-09-09mt7601u: use linux/bitfield.hJakub Kicinski
Use the newly added linux/bitfield.h. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-09-09mt7601u: remove unnecessary includeJakub Kicinski
There is no need to include linux/version.h in a in-tree driver. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-09-09mt7601u: remove redefinition of GENMASKJakub Kicinski
Remove redefinition of GENMASK which should not be there in the upstream version of the code. Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-04-12cfg80211: remove enum ieee80211_bandJohannes Berg
This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-03-07mt7601u: do not free dma_buf when ivp allocation failsColin Ian King
If the allocation of ivp fails the error handling attempts to free an uninitialized dma_buf; this data structure just contains garbage on the stack, so the freeing will cause issues when the urb, buf and dma fields are free'd. Fix this by not free'ing the dma_buf if the ivp allocation fails. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2016-01-14mac80211: pass block ack session timeout to to driverSara Sharon
Currently mac80211 does not inform the driver of the session block ack timeout when starting a rx aggregation session. Drivers that manage the reorder buffer need to know this parameter. Seeing that there are now too many arguments for the drv_ampdu_action() function, wrap them inside a structure. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-09-22mac80211: allow to transmit A-MSDU within A-MPDUEmmanuel Grumbach
Advertise the capability to send A-MSDU within A-MPDU in the AddBA request sent by mac80211. Let the driver know about the peer's capabilities. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-08-10mt7601u: lock out rx path and tx status reportingJakub Kicinski
mac80211 requires that rx path does not run concurrently with tx status reporting. Add a spinlock which will ensure that. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: fix tx status reporting contextsJakub Kicinski
mac80211 requires that rx path does not run concurrently with tx status reporting. Since rx path is run in driver tasklet, tx status cannot be reported directly from interrupt context (there would be no way to lock it out). Add tasklet for tx and move all possible code from irq handler there. Note: tx tasklet is needed because workqueue is queued very rarely and that kills TCP performance. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: use correct ieee80211_rx variantJakub Kicinski
Rx is run inside a tasklet so ieee80211_rx() should be used instead of ieee80211_rx_ni(). Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-08-10mt7601u: fix dma from stack addressJakub Kicinski
DMA to variables located on the stack is a bad idea. For simplicity and to avoid frequent allocations create a buffer inside the device structure. Protect this buffer with vendor_req_mutex. Don't protect vendor requests which don't use this buffer. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-23Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== Major changes: mwifiex: * enhancements for AP mode: support verbose information in station dump command and also information about AP link. * enable power save by default brcmfmac: * fix module reload issue for PCIe * improving msgbuf protocol for PCIe devices * rework .get_station() cfg80211 callback operation * determine interface combinations upon device feature support ath9k: * ath9k_htc: add support of channel switch wil6210: * add modparam for bcast ring size * support hidden SSID * add per-MCS Rx stats ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-06-15mt7601u: don't warn about devices without per-rate power tableJakub Kicinski
We expect EEPROM per-rate power table to be filled with s6 values and warn user if values are invalid. However, there appear to be devices which don't have this section of EEPROM initialized. In such case we should ignore the values and leave the driver power tables set to zero. Note that vendor driver doesn't care about this case but mt76x2 skips 0xff per value. We take mt76x2's approach. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-10mac80211: convert HW flags to unsigned long bitmapJohannes Berg
As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-06-08mt7601u: set promiscous mode based on FIF_OTHER_BSSJakub Kicinski
Most drivers use FIF_OTHER_BSS to set promiscous mode. Let us follow their lead even though it doesn't match exactly the HW filter flags. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: don't cleanup device second time after .resume()Jakub Kicinski
Make sure .disconnect() doesn't cleanup the device if .resume() failed. This may happen when device is removed during suspend. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: watch out for invalid-length framesJakub Kicinski
Users of older Ralink devices report that received frames sometimes have zero length. Watch out for that. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-06-08mt7601u: unify paged and non-paged RX dma pathsJakub Kicinski
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-05-28add mt7601u driverJakub Kicinski
Add support for the simplest of MediaTek Wi-Fi devices - MT7601U. It is a single stream bgn chip with no bells or whistles. This driver is partially based on Felix's mt76 but IMHO it doesn't make sense to merge the two right now because MT7601U is a design somewhere between old Ralink devices and new Mediatek chips. There wouldn't be all that much code sharing with the devices mt76 supports. Situation may obviously change when someone decides to extend m76 with support for the more recent USB dongles. The driver supports only station mode. I'm hoping to add AP support when time allows. This driver sat on GitHub for quite a while and got some testing there: http://github.com/kuba-moo/mt7601u Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 23:29:20 +0000