| Age | Commit message (Collapse) | Author |
|---|
|
No functional change, make recover from statistics code
easies to read.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/e1000e/netdev.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When .config has different configuration, it might fail to compile
iwlwifi. fix it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
sco_cmd is not being used, remove it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
For 2030 series of devices, 2030 macro need to be used.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The beacon notification changed between 4965 and
agn because the embedded TX response changed, but
iwlwifi was never updated to know about this.
Update it now so the IBSS manager status will be
tracked correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Allow peers to size their reorder buffer more
accurately by advertising that we'll never send
aggregates longer than the default (31).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
In order to support RSN IBSS, we need to
(ok actually maybe it's just easiest to)
disable group key programming so that any
group-addressed frames will be decrypted
in software which handles the per-station
keys for this easily. We could keep the
encryption in the device, but that takes
more work and seems unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
For agn devices, always support idle mode which help power
consumption in idle unassociated state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
The I/Q swapping is extremely important and should be dealt with extra care.
It will affects OFDM and CCK differently.
For 6000/6005/6030 series devices, the I/Q were swapped, and for 2000 series
devices, it is in non-swapped status (but its swapped with respected to 6000/6005/6030).
so the CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER register need to be set to support
the correct behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Minor adjustment for rate scale table
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Driver check alive message from ucode, if it is not ok, then need
to restart the loading process. instead of checking multiple places
for failure, only need to check in once place when receive alive
message from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
After commit 59eb21a6504731fc16db4cf9463065dd61093e08
"cfg80211: Extend channel to frequency mapping for 802.11j"
we use uninitialized sband->band when assign channel frequencies, what
results that 5GHz channels have erroneous (zero) center_freq value.
Patch fixes problem and simplifies code a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Only use IWL_RATE_COUNT_3945 in 3945 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/init.c
|
|
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e error "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
If PAN functionality is present, advertise
P2P interface type support and thus support
for P2P. However, the support is currently
somewhat incomplete -- NoA schedule isn't
added to probe responses, and 11b bitrates
may be used still, etc. Therefore, make it
all optional with a Kconfig option.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
There are a number of places where the minimum
slot time is hardcoded to 20 TU, add a new
constant for that and use it everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
For device supporting PAN/P2P, use the PAN
context to implement the remain-on-channel
operation using device offloads so that the
filters in the device will be programmed
correctly -- otherwise we cannot receive
any probe request frames during off-channel
periods.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iwlagn powersave algorithm uses the supports_idle parameter
to tell the device to save power when it is not associated with
an AP and is idle.
Enable this feature for the 1000 series of devices.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
the sram data dumped through the debugfs interface would only work properly
when dumping data on even u32 boundaries and swap bytes based on endianness
on that boundary making byte arrays impossible to read.
now addresses are displayed at the start of every line and the data is
displayed consistently if dumping 1 byte or 20 and regardless of what is the
starting address.
if no lenght given, address displayed is u32 in device format
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
2000 series device has different HW rev, add it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Remove refernce of g2 and use offical number for hw rev.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Remove Gen 2 from Kconfig file since 6005/6030/6150 series of
products are released.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Add 2000 series support to Kconfig
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Add PCI ID supports for all 2000 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Adding 2000 series devices supports, the 2000 series devices has
many different SKUs which includes 1x1 and 2x2 devices,also with
and without BT combo.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Adding EEPROM version for 2000 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Since 6005, 6030 and 6150 series are offical released, remove the reference
to gen2x and use the product number instead.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Instead of keeping track of LED blink speed
in the driver, use the new mac80211 trigger
and link it up with an LED classdev that we
now register. This also allows users more
flexibility in how they want to have the LED
blink or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The notification wait support code is shared
between 4965 and other AGN devices, so 4965
also has to initialize the data structures
for it, otherwise it crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Previously I hacked this with an msleep(300)
which was fine since we never had longer PAN
time slots, but now that we will have them I
need to fix that. Use the new notification
wait support to properly wait for the WIPAN
deactivation complete signal from the ucode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to implement waiting for notifications,
add a structure that captures the information,
and a list of such structures that will be
traversed when a command is received from the
ucode.
Use sparse checking to make sure calls to the
prepare/wait/cancel functions are always nested
correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It's not used or likely to be needed from other
files, so it can be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For all the new devices, the sku information should read from EEPROM
but for legacy devices such as 4965, appearly the EEPROM does not
contain the necessary information. so skip the read from EEPROM
and go back to use software configuration.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
