| Age | Commit message (Collapse) | Author |
|---|
|
Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.
For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).
Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.
After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
CQM overwrites a few thresholds in the bf command. On the other hand,
when entering D0i3 the thresholds are set to higher values on purpose,
so ignore CQM in this case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The slow filtering threshold should be higher in D0i3 case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
TCP software implementation on the host requires extensive computing
power. Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
use the AP station for multicast frames instead of the auxiliary
station as otherwise the frames can be sent to an absent P2P GO as
the FW does not block transmissions for the auxiliary station
since it is not associated with the station MAC context.
Note that this is not possible for unicast frames, as a TDLS
discovery response is sent without a station entry, and in this
case the P2P GO NoA should not block transmission to the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Allow the transport layer to return an error upon suspend.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This reverts commit 088070a2f6575402d3dd82e1c5a4a8e1941805f6.
When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).
However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.
Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Existing UMAC commands already use the long header, but are sent
with group 0 and the long header inserted manually. Move them to
the group 1 to take advantage of the header building in the low-
level transport.
Existing firmware ignores the group_id field (it's reserved) and
the first firmware that really supports long command headers can
parse all commands in both group 0 (with short header) and group
1 (with long header.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
As the firmware is slowly running out of command IDs and grouping of
commands is desirable anyway, the firmware is extending the command
header from 4 bytes to 8 bytes to introduce a group (in place of the
former flags field, since that's always 0 on commands and thus can
be easily used to distinguish between the two.
In order to support this most easily in the driver widen the command
command ID used in the command sending functions and encode the new
values (group and version) in the ID. That way existing code doesn't
have to be changed (since the higher bits are 0 automatically) and
newer code can easily use the new ID generation function to create a
value to use in place of just the command ID.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
All the supported firmwares support this API.
This includes removing dwell per band, as band is no longer a factor
in calculating the dwell. Only basic dwell is used and FW will calculate
the actual dwell time.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The 'flags' field really has been reserved in the firmware API for a
very long time, probably since 4965. As a consequence, the field is
always 0 and checking for a IWL_CMD_FAILED_MSK flag makes no sense.
Rename the field to 'reserved', get rid of IWL_CMD_FAILED_MSK and
all the code for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Since the time-event is sent with the immediate flag set, there is
no need to sample the device time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
With the previous patch series, no opmode continues using the
command or handler_status (i.e. the return value from the RX)
so it can be removed now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In the mvm driver, neither the old command nor the return value
are used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The current key offset assignment algorithm always uses the lowest
unused key offset, which will potentially lead to issues when the
firmware will change to take the key material for TX from the key
table rather than from the TX command.
In order to avoid those issues (and avoid forgetting about them)
change the key offset allocation algorithm now to avoid reusing key
offsets quickly.
The new algorithm always picks as the next offset the least recently
freed offset, i.e. the offset that has been unused for the longest
amount of time. This is implemented by having a generation counter
for each key offset that is incremented every time a key is deleted,
except for the one that's deleted, which is reset to zero. Thus the
highest counter is the key that's been unused longest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The code checks the total number of iterations to differentiate
between regular scan and scheduled scan. However, regular scan has
a total of one iteration, not zero. As a result, regular scan will
have lower priority than it should have, and in case scheduled
scan is already running when regular scan is requested, regular scan
will be delayed until scheduled scan is aborted.
Fix that by checking for total iterations number of one as an
identifier for regular scan.
Fixes: 133c8259f885 ("iwlwifi: mvm: rename generic_scan_cmd functions to dwell")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add preemptive flag to scheduled scan command flags. Without this
flag, all scan requests after scheduled scan was started will be
delayed until scheduled scan stops. As a result, P2P_FIND will be
blocked while scheduled scan is active.
This flag was omitted during refactoring.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The time event is initialized relatively late in interface (mvmvif)
initialization, so it's possible to fail before that happens. As a
consequence, the driver will crash if it ever tries to delete this
time event in case initialization was unsuccessful.
Avoid this by using the time event's vif pointer to indicate validity.
The vif pointer is != NULL whenever the id is != TE_MAX, except for
this special error case where the vif pointer will have the correct
property (as the whole memory is cleared on allocation) whereas the
id is 0, causing a crash in trying to delete the time event from the
list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Sometimes when setting an igtk key the station maybe NULL.
In the of case igtk the function will skip to the end, and
try to print sta->addr, if sta is Null - we will access a
Null pointer.
Avoid accessing a Null pointer when setting a igtk key &
the sta == NULL, and print a default MAC address instead.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181
CC: <stable@vger.kernel.org> [3.17+]
Fixes: 34c8b24ff284 ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This firmware is not supported anymore - stop loading this firmware.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
There's no need to forward RX MPDUs to notification wait tests, nor
do we need to check them for firmware dump triggers, nor could they
be asynchronous. It's thus more efficient to handle them separately,
before going into the regular RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In scenarios where we haven't converged yet to a specific modulation
and rate it could be better to report to userspace the last tx rate
based on the STA capabilities and RSSI. This is important as sometimes
userspace displays the last tx rate as the link speed.
This avoids being presented with low legacy rates when rs just begins
its search or after an idle period in which it resets itself.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Merge back net-next to get wireless driver changes (from Kalle)
to be able to create the API change across all trees properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.
To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add DC2DC_CONFIG_CMD (0x83) cmd.
Add IWL_UCODE_TLV_CAPA_DC2DC_CONFIG_SUPPORT tlv.
The command allows the driver get & set the DCDC's frequency tune.
(freq_tune is the divider that is used to calculate the actual DCDC's
clock rate)
The command always returns the current/updated frequency tune values of
the DCDC.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firmwares that used these commands is not supported
anymore. Remove them.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Currently, loading the firmware fails when it has higher API or CAPA
bits than the driver supports. That's an issue with integration.
At the same time, actually using api[0] and capa[0] will become
confusing when we also have api[1] and capa[1], and it's almost
certain that we'll mix up the bits and use the bits for api[1] with
api[0] by accident.
Avoid all this by translating the API/CAPA bits to the regular kernel
test_bit() format, and also providing wrapper functions. Also use the
__bitwise__ facility of sparse to check that we're testing the right
one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
As pointed out by smatch, there's no need for a loop that always
immediately terminates. Use an if statement instead and while at
it clean up the mvmvif initialization.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Since the firmware is responsible for duration calculation, the
driver can easily support fast-xmit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
On resume, all the interrupts are masked (CSR_INT_MASK is 0),
and ict is disabled.
Re-configure them both.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Don't use EBS for P2P find to make sure we find all GOs in
our only attempt.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Currently EBS status in scan complete notifications is set to
success if EBS wasn't activated. FW will add a special return
value for cases when EBS wasn't activated and we add a print
of this status.
This change is needed for debug only, no behavior changes.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Allow a cleaner way to access those hw-dependent registers,
instead of using the product family type etc.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
A minor refactoring for following patches.
This enables the reuse of the checks functions.
type=cleanup
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The naming convention is to always have the flags prefixed with
IEEE80211_HW_ so they're 'namespaced', make this flag follow it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a HW recovery was started but not completed since all interfaces went
down, make sure to cleanup all interfaces before clearing the HW_RESTART
flag.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
BlockAck sessions can have events that are interesting to
debug. When we send or receive a BAR, it is may indicate
that something bad is happening. Even more so when mac80211
tells us that a frame timed out in the reodering buffer.
Add a few triggers for BlockAck session debugging.
Allow per-TID debugging.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
For UMAC, we were not treating a race condition that happens in the
scan flows, because it was not using the same state flags. Now that
UMAC and LMAC scans use the same state flags, we can also handle the
race conditions for UMAC.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
UMAC scans now use the general scan status for almost everything, the
only part missing was in the scan complete notifications. Change it
to use the stopping flags instead of clearing the flags when the stop
comes from above and clean the handler function a bit.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The UMAC and LMAC scan_stop functions are now nearly identical, so
they can be combined into a single function instead.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We can only have one scan per type at the same time, so the code that
tries to stop several scans of a type is unnecessary. Remove that to
reduce code complexity.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
We can only have one scan of each type running at the same time, so we
can remove one attribute in the UID information we save. We had array
index, UID and type, but only UID (== array_index) and type are
necessary. Refactor the code to use this simplified array.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add support for scan priority API with 8 levels instead of the
existing 3 levels. This API is needed to define the priority of
new ooc activities, e.g. gscan.
Add a TLV flag to indicate if the new API is supported so that
devices that does not support the new API will continue to use
the old one.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
