summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/intel/iwlwifi/pcie/trans.c
AgeCommit message (Collapse)Author
2019-11-05Merge tag 'wireless-drivers-next-2019-11-05' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.5 First set of patches for 5.5. The most active driver here clearly is rtw88, lots of patches for it. More quiet on other drivers, smaller fixes and cleanups all over. This pull request also has a trivial conflict, the report and example resolution here: https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au Major changes: rtw88 * add deep power save support * add mac80211 software tx queue (wake_tx_queue) support * enable hardware rate control * add TX-AMSDU support * add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support * add power tracking support * add 802.11ac beamformee support * add set_bitrate_mask support * add phy_info debugfs to show Tx/Rx physical status * add RFE type 3 support for 8822b ath10k * add support for hardware rfkill on devices where firmware supports it rtl8xxxu * add bluetooth co-existence support for single antenna iwlwifi * Revamp the debugging infrastructure ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-25iwlwifi: dbg_ini: add TLV allocation new API supportShahar S Matityahu
Add new debug TLVs API preprocessing. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-25iwlwifi: dbg_ini: add monitor dumping supportShahar S Matityahu
Allow collecting monitor data in ini debug mode. Implement both SMEM and DRAM monitor regions dumping. For DRAM monitor, support DBGC1, DBGC2 and DBGC3 and support several DRAM fragments per DBGC. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-25iwlwifi: dbg: remove multi buffers infraShahar S Matityahu
Legacy DRAM monitor does not support multi buffers. Remove this infra. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-09iwlwifi: pcie: fix rb_allocator workqueue allocationJohannes Berg
We don't handle failures in the rb_allocator workqueue allocation correctly. To fix that, move the code earlier so the cleanup is easier and we don't have to undo all the interrupt allocations in this case. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-09iwlwifi: pcie: fix indexing in command dump for new HWJohannes Berg
We got a crash in iwl_trans_pcie_get_cmdlen(), while the TFD was being accessed to sum up the lengths. We want to access the TFD here, which is the information for the hardware. We always only allocate 32 buffers for the cmd queue, but on newer hardware (using TFH) we can also allocate only a shorter hardware array, also only 32 TFDs. Prior to the TFH, we had to allocate a bigger TFD array but would make those point to a smaller set of buffers. Additionally, now max_tfd_queue_size is up to 65536, so we can access *way* out of bounds of a really only 32-entry array, so it crashes. Fix this by making the TFD index depend on which hardware we are using right now. While changing the calculation, also fix it to not use void ptr arithmetic, but cast to u8 * before. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-23Merge tag 'pci-v5.4-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it (Krzysztof Wilczynski) - Fix incorrect PCIe device types and remove dev->has_secondary_link to simplify code that deals with upstream/downstream ports (Mika Westerberg) - After suspend, restore Resizable BAR size bits correctly for 1MB BARs (Sumit Saxena) - Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra) Virtualization: - Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna Labs (Ali Saidi) - Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg) - Remove group write permissions from sysfs sriov_numvfs, sriov_drivers_autoprobe (Kelsey Skunberg) Hotplug: - Simplify pciehp indicator control (Denis Efremov) Peer-to-peer DMA: - Allow P2P DMA between root ports for whitelisted bridges (Logan Gunthorpe) - Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe) - DMA map P2P DMA requests that traverse host bridge (Logan Gunthorpe) Amazon Annapurna Labs host bridge driver: - Add DT binding and controller driver (Jonathan Chocron) Hyper-V host bridge driver: - Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui) - Fix PCI domain number collisions (Haiyang Zhang) - Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang) - Fix build errors on non-SYSFS config (Randy Dunlap) i.MX6 host bridge driver: - Limit DBI register length (Stefan Agner) Intel VMD host bridge driver: - Fix config addressing issues (Jon Derrick) Layerscape host bridge driver: - Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao) - Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately (Xiaowei Bao) Mediatek host bridge driver: - Add MT7629 controller support (Jianjun Wang) Mobiveil host bridge driver: - Fix CPU base address setup (Hou Zhiqiang) - Make "num-lanes" property optional (Hou Zhiqiang) Tegra host bridge driver: - Fix OF node reference leak (Nishka Dasgupta) - Disable MSI for root ports to work around design problem (Vidya Sagar) - Add Tegra194 DT binding and controller support (Vidya Sagar) - Add support for sideband pins and slot regulators (Vidya Sagar) - Add PIPE2UPHY support (Vidya Sagar) Misc: - Remove unused pci_block_cfg_access() et al (Kelsey Skunberg) - Unexport pci_bus_get(), etc (Kelsey Skunberg) - Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in the PCI core (Kelsey Skunberg) - Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg) - Mark expected switch fall-through (Gustavo A. R. Silva) - Propagate errors for optional regulators and PHYs (Thierry Reding) - Fix kernel command line resource_alignment parameter issues (Logan Gunthorpe)" * tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits) PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI arm64: tegra: Add PCIe slot supply information in p2972-0000 platform arm64: tegra: Add configuration for PCIe C5 sideband signals PCI: tegra: Add support to enable slot regulators PCI: tegra: Add support to configure sideband pins PCI: vmd: Fix shadow offsets to reflect spec changes PCI: vmd: Fix config addressing when using bus offsets PCI: dwc: Add validation that PCIe core is set to correct mode PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port PCI: Add ACS quirk for Amazon Annapurna Labs root ports PCI: Add Amazon's Annapurna Labs vendor ID MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries dt-bindings: PCI: tegra: Add sideband pins configuration entries PCI: tegra: Add Tegra194 PCIe support PCI: Get rid of dev->has_secondary_link flag ...
2019-09-06iwlwifi: add support for suspend-resume flow for new device generationHaim Dreyfuss
The new device generation has a slightly different suspend resume flow Currently, the way the driver instruct the device to move to D3 is by sending D3_CONFIG_CMD. Instead of using the host command the indication is by writing to the doorbell interrupt. The FW will respond with interrupt to indicate transition completion. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: always access the trans configuration via transLuca Coelho
Stop accessing the trans configuration via the iwl_cfg structure and always access it via the iwl_trans structure. This completes the requirements to disassociate the trans-specific configuration from the rest of the configuration. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: add a pointer to the trans_cfg directly in transLuca Coelho
Add a pointer to the iwl_trans structure and point it to the trans part of the cfg. This is the first step in disassociating the trans configuration from the rest of the configuration. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pass the iwl_config_trans_params when neededLuca Coelho
Instead of accessing the iwl_config_trans_params from the cfg that is stored in the trans struct, pass this structure directly to functions that need it during trans_alloc. This will be useful to isolate the elements needed during allocation and pass them separately before the actual cfg struct is known. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pcie: set iwl_trans->cfg later in the probe functionLuca Coelho
Instead of setting the cfg to iwl_trans already during allocation, set it only later when we have had the time to decide which cfg to use. This is part of the effort to be able to decide the cfg based on HW revision and RF ID after iwl_trans_alloc() has been called. For now, since we still have a bunch of code checking the HW revision and the RF ID, we set iwl_trans->cfg early, even before we decided the real cfg to use. We only use the trans configuration at this point, so this is fine for now. In the future, the trans configuration will be completely independent from the rest of the config structure, so we'll be able to avoid this. Additionally, we can't access the PRPH registers in iwl_trans_alloc() anymore, so move the HW REV C-step check for family 8000 code later to the probe function as well. This step is probably not necessary, but if that's the case it should be removed separately later on. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pcie: move some cfg mangling from trans_pcie_alloc to probeLuca Coelho
There were a couple of special handling to find the correct cfg inside iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're together with the rest of the decisions. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pcie: use the cfg we passed to iwl_trans_pcie_alloc()Luca Coelho
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the local argument that we received. This will allow us to not to set the cfg during iwl_trans_alloc() so it can be decided later. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: separate elements from cfg that are needed by trans_allocLuca Coelho
In order to be able to select the cfg depending on the HW revision or on the RF ID, we need to set up the trans before selecting the cfg. To do so, move the elements from cfg that are needed by iwl_trans_alloc() to a separate struct at the top of the cfg, so it can be used by other cfg types as well, before selecting the rest of the configuration. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: dbg: align wrt log prints to the same formatShahar S Matityahu
Align wrt log prints to the driver coding style Remove the ext field from the log and print it at the beginning of the apply point. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: dbg_ini: use function to check if ini dbg mode is onShahar S Matityahu
use iwl_trans_dbg_ini_valid function instead of a boolean value check if dbg_ini mode is on. It is needed for a future patch. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: stop passing bogus gfp flags arguments to dma_alloc_coherentChristoph Hellwig
dma_alloc_coherent is not just the page allocator. The only valid arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible modifiers of __GFP_NORETRY or __GFP_NOWARN. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: remove pm_runtime completelyEmmanuel Grumbach
This means: 1) stop calling pm_runtime_resume when starting the hardware 2) removing the unneeded low_power parameter to start / stop hw / fw transport ops 3) squashing transport functions that are now the same _iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pcie: remove some more d0i3 code from the transportEmmanuel Grumbach
CMD_SEND_IN_IDLE, CMD_MAKE_TRANS_IDLE and CMD_WAKE_UP_TRANS are not used. Remove them. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: pcie: remove the refs / unrefs from the transportEmmanuel Grumbach
This code is now stale Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: remove runtime_pm_modeEmmanuel Grumbach
This is always set to IWL_PLAT_PM_MODE_DISABLED Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: Set w-pointer upon resume according to SNAlex Malamud
During D3 state, FW may send packets. As a result, "write" queue pointer will be incremented by FW. Upon resume from D3, driver should adjust its shadows of "write" and "read" pointers to the value reported by FW. 1. Keep TID used during wowlan configuration. 2. Upon resume, set driver's "write" and "read" queue pointers to the value reported by FW. Signed-off-by: Alex Malamud <alex.malamud@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: remove the code under IWLWIFI_PCIE_RTPMEmmanuel Grumbach
This flag should never be set unless integration work with the platform is done. We don't support any platforms officially and don't plan to do so in the near future, so we can remove this option entirely in order to avoid having it enabled by mistake. This has been marked with "depends on EXPERT", so there shouldn't be many systems running with it set. And, if there are systems, they should not be using this flag. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: dbg: move debug recording stop from trans to op modeShahar S Matityahu
The op mode should stop the debug recording and not the transport layer. Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug stop recording to it. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-08-29iwlwifi: pcie: handle switching killer Qu B0 NICs to C0Luca Coelho
We need to use a different firmware for C0 versions of killer Qu NICs. Add structures for them and handle them in the if block that detects C0 revisions. Additionally, instead of having an inclusive check for QnJ devices, make the selection exclusive, so that switching to QnJ is the exception, not the default. This prevents us from having to add all the non-QnJ cards to an exclusion list. To do so, only go into the QnJ block if the device has an RF ID type HR and HW revision QnJ. Cc: stable@vger.kernel.org # 5.2 Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2019-08-28PCI: Move ASPM declarations to linux/pci.hKrzysztof Wilczynski
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h to include/linux/pci.h so users only need to include <linux/pci.h>: PCIE_LINK_STATE_L0S PCIE_LINK_STATE_L1 PCIE_LINK_STATE_CLKPM pci_disable_link_state() pci_disable_link_state_locked() pcie_no_aspm() No functional changes intended. Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com Signed-off-by: Krzysztof Wilczynski <kw@linux.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2019-08-20iwlwifi: pcie: don't switch FW to qnj when ax201 is detectedLuca Coelho
We have a too generic condition that switches from Qu configurations to QnJ configurations. We need to exclude some configurations so that they are not erroneously switched. Add the ax201 configuration to the list of exclusions. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-07-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Two cases of overlapping changes, nothing fancy. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-29iwlwifi: dbg: debug recording stop and restart command removeShahar S Matityahu
The 0xF6 command used to start and stop the recording from 22560 devices was removed. This is causing an assert when the driver tries to alter the recording state. Remove the use of the command. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: dbg: move trans debug fields to a separate structShahar S Matityahu
Unite iwl_trans debug related fields under iwl_trans_debug struct to increase readability and keep iwl_trans clean. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: dbg_ini: remove redundant checking of ini modeShahar S Matityahu
There are several flows where the driver checks if it runs in ini mode. Some of these flows are no longer used in ini mode or there is another condition that check the ini mode in the same flow. Either way, those conditions are redundant. Remove the redundant conditions. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: pcie: increase the size of PCI dumpsLuca Coelho
Currently we dump only the first 64 bytes of the PCI config space, which leaves out some important things, such as the base address registers. Increase it to 352 for the PCI device and to 524 for the rootport to make sure we include everything we need. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: dbg: allow dump collection in case of an early errorShahar S Matityahu
Improve the robustness of the dump collection flow in case of an early error: 1. in iwl_trans_pcie_sync_nmi, disable and enable interrupts only if they were already enabled 2. attempt to initiate dump collection in iwl_fw_dbg_error_collect only if the device is enabled 3. check Tx command queue was already allocated before trying to collect it Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-24iwlwifi: add support for hr1 RF IDOren Givon
The 22000 series FW that was meant to be used with hr is also the FW that is used for hr1 and has a different RF ID. Add support to load the hr FW when hr1 RF ID is detected. Cc: stable@vger.kernel.org # 5.1+ Signed-off-by: Oren Givon <oren.givon@intel.com> Signed-off-by: Luciano Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-24iwlwifi: add new cards for 22000 and change wrong structsIhab Zhaika
add few PCI ID'S for 22000 and chainge few cards structs names Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-24iwlwifi: add new cards for 22000 and fix struct nameIhab Zhaika
add few PCI ID'S for 22000 and fix the wrong name for one of the structs Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: fix AX201 killer sku loading firmware issueMatt Chen
When try to bring up the AX201 2 killer sku, we run into: [81261.392463] iwlwifi 0000:01:00.0: loaded firmware version 46.8c20f243.0 op_mode iwlmvm [81261.407407] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AX 22000, REV=0x340 [81262.424778] iwlwifi 0000:01:00.0: Collecting data: trigger 16 fired. [81262.673359] iwlwifi 0000:01:00.0: Start IWL Error Log Dump: [81262.673365] iwlwifi 0000:01:00.0: Status: 0x00000000, count: -906373681 [81262.673368] iwlwifi 0000:01:00.0: Loaded firmware version: 46.8c20f243.0 [81262.673371] iwlwifi 0000:01:00.0: 0x507C015D | ADVANCED_SYSASSERT Fix this issue by adding 2 more cfg to avoid modifying the original cfg configuration. Signed-off-by: Matt Chen <matt.chen@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: print fseq info upon fw assertShahar S Matityahu
Read fseq info from FW registers and print it upon fw assert. The print is needed since the fseq version coming from the TLV might not be the actual version that is used. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-06-01iwlwifi: clear persistence bit according to device familyShahar S Matityahu
The driver attempts to clear persistence bit on any device familiy even though only 9000 and 22000 families require it. Clear the bit only on the relevant device families. Each HW has different address to the write protection register. Use the right register for each HW Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: 8954e1eb2270 ("iwlwifi: trans: Clear persistence bit when starting the FW") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-05-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: "Highlights: 1) Support AES128-CCM ciphers in kTLS, from Vakul Garg. 2) Add fib_sync_mem to control the amount of dirty memory we allow to queue up between synchronize RCU calls, from David Ahern. 3) Make flow classifier more lockless, from Vlad Buslov. 4) Add PHY downshift support to aquantia driver, from Heiner Kallweit. 5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces contention on SLAB spinlocks in heavy RPC workloads. 6) Partial GSO offload support in XFRM, from Boris Pismenny. 7) Add fast link down support to ethtool, from Heiner Kallweit. 8) Use siphash for IP ID generator, from Eric Dumazet. 9) Pull nexthops even further out from ipv4/ipv6 routes and FIB entries, from David Ahern. 10) Move skb->xmit_more into a per-cpu variable, from Florian Westphal. 11) Improve eBPF verifier speed and increase maximum program size, from Alexei Starovoitov. 12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit spinlocks. From Neil Brown. 13) Allow tunneling with GUE encap in ipvs, from Jacky Hu. 14) Improve link partner cap detection in generic PHY code, from Heiner Kallweit. 15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan Maguire. 16) Remove SKB list implementation assumptions in SCTP, your's truly. 17) Various cleanups, optimizations, and simplifications in r8169 driver. From Heiner Kallweit. 18) Add memory accounting on TX and RX path of SCTP, from Xin Long. 19) Switch PHY drivers over to use dynamic featue detection, from Heiner Kallweit. 20) Support flow steering without masking in dpaa2-eth, from Ioana Ciocoi. 21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri Pirko. 22) Increase the strict parsing of current and future netlink attributes, also export such policies to userspace. From Johannes Berg. 23) Allow DSA tag drivers to be modular, from Andrew Lunn. 24) Remove legacy DSA probing support, also from Andrew Lunn. 25) Allow ll_temac driver to be used on non-x86 platforms, from Esben Haabendal. 26) Add a generic tracepoint for TX queue timeouts to ease debugging, from Cong Wang. 27) More indirect call optimizations, from Paolo Abeni" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits) cxgb4: Fix error path in cxgb4_init_module net: phy: improve pause mode reporting in phy_print_status dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings net: macb: Change interrupt and napi enable order in open net: ll_temac: Improve error message on error IRQ net/sched: remove block pointer from common offload structure net: ethernet: support of_get_mac_address new ERR_PTR error net: usb: smsc: fix warning reported by kbuild test robot staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check net: dsa: support of_get_mac_address new ERR_PTR error net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats vrf: sit mtu should not be updated when vrf netdev is the link net: dsa: Fix error cleanup path in dsa_init_module l2tp: Fix possible NULL pointer dereference taprio: add null check on sched_nest to avoid potential null pointer dereference net: mvpp2: cls: fix less than zero check on a u32 variable net_sched: sch_fq: handle non connected flows net_sched: sch_fq: do not assume EDT packets are ordered net: hns3: use devm_kcalloc when allocating desc_cb net: hns3: some cleanup for struct hns3_enet_ring ...
2019-05-06Merge tag 'arm64-mmiowb' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull mmiowb removal from Will Deacon: "Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb()) Remove mmiowb() from the kernel memory barrier API and instead, for architectures that need it, hide the barrier inside spin_unlock() when MMIO has been performed inside the critical section. The only relatively recent changes have been addressing review comments on the documentation, which is in a much better shape thanks to the efforts of Ben and Ingo. I was initially planning to split this into two pull requests so that you could run the coccinelle script yourself, however it's been plain sailing in linux-next so I've just included the whole lot here to keep things simple" * tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits) docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section arch: Remove dummy mmiowb() definitions from arch code net/ethernet/silan/sc92031: Remove stale comment about mmiowb() i40iw: Redefine i40iw_mmiowb() to do nothing scsi/qla1280: Remove stale comment about mmiowb() drivers: Remove explicit invocations of mmiowb() drivers: Remove useless trailing comments from mmiowb() invocations Documentation: Kill all references to mmiowb() riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock() m68k/io: Remove useless definition of mmiowb() nds32/io: Remove useless definition of mmiowb() x86/io: Remove useless definition of mmiowb() arm64/io: Remove useless definition of mmiowb() ARM/io: Remove useless definition of mmiowb() mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors ...
2019-05-05Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Most likely the last patchset of new feature for 5.2, and this time we have quite a lot of new features. Most obvious being rtw88 from Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We have also new hardware support for existing drivers and improvements. There's one conflict in iwlwifi, my example conflict resolution below. Major changes: iwlwifi * bump the 20000-series FW API version * work on new hardware continues * RTT confidence indication support for Fine Timing Measurement (FTM) * an improvement in HE (802.11ax) rate-scaling * add command version parsing from the fimware TLVs * add support for a new WoWLAN patterns firmware API rsi * add support for rs9116 mwifiex * add support for SD8987 brcmfmac * add quirk for ACEPC T8 and T11 mini PCs rt2x00 * add RT3883 support qtnfmac * fix debugfs interface to support multiple cards rtw88 * new driver mt76 * share more code across drivers * add support for MT7615 chipset * rework DMA API * tx/rx performance optimizations * use NAPI for tx cleanup on mt76x02 * AP mode support for USB devices * USB stability fixes * tx power handling fixes for 76x2 * endian fixes Conflicts: There's a trivial conflict in drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be just empty: diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h index cd622af90077,b0671e16e1ce..000000000000 --- a/drivers/net/wireless/intel/iwlwifi/fw/file.h +++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three trivial overlapping conflicts. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-29iwlwifi: pcie: initialize debug_rfkill to -1Johannes Berg
This will let us introduce a mechanism to start with rfkill faked, and put 0 here to override it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: dbg_ini: add debug prints to the ini flowsShahar S Matityahu
Add debug prints to the ini flow and rewrite existing prints to provide more information Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Nothing really special standing out this time, iwlwifi being the most active driver. Major changes: iwlwifi * send NO_DATA events so they can be captured in radiotap * support for multiple BSSID * support for some new FW API versions * support new hardware * debugfs cleanups by Greg-KH qtnfmac * allow each MAC to specify its own regulatory rules ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-18iwlwifi: don't panic in error path on non-msix systemsShahar S Matityahu
The driver uses msix causes-register to handle both msix and non msix interrupts when performing sync nmi. On devices that do not support msix this register is unmapped and accessing it causes a kernel panic. Solve this by differentiating the two cases and accessing the proper causes-register in each case. Reported-by: Michal Hocko <mhocko@kernel.org> Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-08drivers: Remove explicit invocations of mmiowb()Will Deacon
mmiowb() is now implied by spin_unlock() on architectures that require it, so there is no reason to call it from driver code. This patch was generated using coccinelle: @mmiowb@ @@ - mmiowb(); and invoked as: $ for d in drivers include/linux/qed sound; do \ spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done NOTE: mmiowb() has only ever guaranteed ordering in conjunction with spin_unlock(). However, pairing each mmiowb() removal in this patch with the corresponding call to spin_unlock() is not at all trivial, so there is a small chance that this change may regress any drivers incorrectly relying on mmiowb() to order MMIO writes between CPUs using lock-free synchronisation. If you've ended up bisecting to this commit, you can reintroduce the mmiowb() calls using wmb() instead, which should restore the old behaviour on all architectures other than some esoteric ia64 systems. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-04-03iwlwifi: pcie: no need to check return value of debugfs_create functionsGreg Kroah-Hartman
When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this. Cc: Johannes Berg <johannes.berg@intel.com> Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Cc: Luca Coelho <luciano.coelho@intel.com> Cc: Intel Linux Wireless <linuxwifi@intel.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 10:41:23 +0000