summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/intel/iwlwifi/fw/file.h
AgeCommit message (Collapse)Author
2021-04-14iwlwifi: mvm: Add support for 6GHz passive scanIlan Peer
When doing scan while 6GHz channels are not enabled, the 6GHz band is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands (that will allow discovery of geographic location etc. that would allow enabling the 6GHz channels) but there are non collocated APs on 6GHz PSC channels these would never be discovered. To overcome this, FW added support for performing passive UHB scan in case no APs were discovered during scan on the 2GHz and 5GHz channels. Add support for enabling such scan when the following conditions are met: - 6GHz channels are supported but not enabled by regulatory. - Station interface is not associated or less than a defined time interval passed from the last resume or HW reset flows. - At least 4 channels are included in the scan request - The scan request includes the widlcard SSID. - At least 50 minutes passed from the last 6GHz passive scan. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-02-25Merge tag 'pci-v5.12-changes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI updates from Bjorn Helgaas: "Enumeration: - Remove unnecessary locking around _OSC (Bjorn Helgaas) - Clarify message about _OSC failure (Bjorn Helgaas) - Remove notification of PCIe bandwidth changes (Bjorn Helgaas) - Tidy checking of syscall user config accessors (Heiner Kallweit) Resource management: - Decline to resize resources if boot config must be preserved (Ard Biesheuvel) - Fix pci_register_io_range() memory leak (Geert Uytterhoeven) Error handling (Keith Busch): - Clear error status from the correct device - Retain error recovery status so drivers can use it after reset - Log the type of Port (Root or Switch Downstream) that we reset - Always request a reset for Downstream Ports in frozen state Endpoint framework and NTB (Kishon Vijay Abraham I): - Make *_get_first_free_bar() take into account 64 bit BAR - Add helper API to get the 'next' unreserved BAR - Make *_free_bar() return error codes on failure - Remove unused pci_epf_match_device() - Add support to associate secondary EPC with EPF - Add support in configfs to associate two EPCs with EPF - Add pci_epc_ops to map MSI IRQ - Add pci_epf_ops to expose function-specific attrs - Allow user to create sub-directory of 'EPF Device' directory - Implement ->msi_map_irq() ops for cadence - Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence - Add EP function driver to provide NTB functionality - Add support for EPF PCI Non-Transparent Bridge - Add specification for PCI NTB function device - Add PCI endpoint NTB function user guide - Add configfs binding documentation for pci-ntb endpoint function Broadcom STB PCIe controller driver: - Add support for BCM4908 and external PERST# signal controller (Rafał Miłecki) Cadence PCIe controller driver: - Retrain Link to work around Gen2 training defect (Nadeem Athani) - Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof Wilczyński) Freescale Layerscape PCIe controller driver: - Add LX2160A rev2 EP mode support (Hou Zhiqiang) - Convert to builtin_platform_driver() (Michael Walle) MediaTek PCIe controller driver: - Fix OF node reference leak (Krzysztof Wilczyński) Microchip PolarFlare PCIe controller driver: - Add Microchip PolarFire PCIe controller driver (Daire McNamara) Qualcomm PCIe controller driver: - Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith) - Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov) Renesas R-Car PCIe controller driver: - Drop PCIE_RCAR config option (Lad Prabhakar) - Always allocate MSI addresses in 32bit space (Marek Vasut) Rockchip PCIe controller driver: - Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai) - Make 'ep-gpios' DT property optional (Chen-Yu Tsai) Synopsys DesignWare PCIe controller driver: - Work around ECRC configuration hardware defect (Vidya Sagar) - Drop support for config space in DT 'ranges' (Rob Herring) - Change size to u64 for EP outbound iATU (Shradha Todi) - Add upper limit address for outbound iATU (Shradha Todi) - Make dw_pcie ops optional (Jisheng Zhang) - Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang) Xilinx Versal CPM PCIe controller driver: - Fix OF node reference leak (Pan Bian) Miscellaneous: - Remove tango host controller driver (Arnd Bergmann) - Remove IRQ handler & data together (altera-msi, brcmstb, dwc) (Martin Kaiser) - Fix xgene-msi race in installing chained IRQ handler (Martin Kaiser) - Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He) - Fix pci-bridge-emul array overruns (Russell King) - Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej Siewior)" * tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits) PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064 PCI: qcom: Add support for ddrss_sf_tbu clock dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250 PCI: al: Remove useless dw_pcie_ops PCI: dwc: Don't assume the ops in dw_pcie always exist PCI: dwc: Add upper limit address for outbound iATU PCI: dwc: Change size to u64 for EP outbound iATU PCI: dwc: Drop support for config space in 'ranges' PCI: layerscape: Convert to builtin_platform_driver() PCI: layerscape: Add LX2160A rev2 EP mode support dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings PCI: dwc: Work around ECRC configuration issue PCI/portdrv: Report reset for frozen channel PCI/AER: Specify the type of Port that was reset PCI/ERR: Retain status from error notification PCI/AER: Clear AER status from Root Port when resetting Downstream Port PCI/ERR: Clear status of the reporting device dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B PCI: rockchip: Make 'ep-gpios' DT property optional Documentation: PCI: Add PCI endpoint NTB function user guide ...
2021-02-11iwlwifi: mvm: add RFI-M supportGregory Greenman
RF Interference Mitigation is a new feature targeted to handle the problem of interference between DDR memory and WiFi. The role of the driver is to configure FW with the table holding a mapping between problematic channels/bands and the corresponding frequencies. This patch adds RFI infrastructure and adds two debugfs hooks: - send RFI configuration command (currently with a default table) which will reset feature in the FW - read the table, used by the FW (which can be a subset of the table that driver sent). Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-02-05iwlwifi: mvm: advertise BIGTK client support if availableJohannes Berg
If the firmware has support, then advertise it to the stack and send the key down. Since we re-check the protection in the host anyway, we don't really need to do anything on RX except that we should drop frames that the firmware _knows_ are replay errors, since beacon filtering might otherwise result in replays being possible. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5a3d53301b3.I23e84c9bb0b039d9106a07e9d6847776757f9029@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-02-05iwlwifi: parse phy integration string from FW TLVDror Moshe
Parse phy integration string from FW TLV. Signed-off-by: Dror Moshe <drorx.moshe@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20210117164916.0c790e930484.I23ef2cb9c871e6adc4aab6be378f3811cb531155@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2021-01-29Fix "ordering" comment typosBjorn Helgaas
Fix comment typos in "ordering". Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Vasily Gorbik <gor@linux.ibm.com> # s390
2020-12-10iwlwifi: support firmware reset handshakeJohannes Berg
There are some races in the hardware that can possibly lead to a bus lockup later during a restart when we manage to kill the firmware at a bad time (while it's accessing the bus). To work around this, add support for a new handshake between firmware and driver to ensure that the firmware is in a well- known state before we kill it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201209231352.7756fcc9865c.I13de65e0ffcb4186dd4c1a465f66df2e98c9a947@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-12-10iwlwifi: use SPDX tagsJohannes Berg
Use SPDX tags instead of the long copyright notices. Also cleanup some duplicate copyright notices and combine the years where possible. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201210000603.481bcb512a6f.I8146abe5a637079e7336209f23cb26af98b12b31@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-12-10iwlwifi: fw: file: fix documentation for SAR flagJohannes Berg
This was mistakenly tagged with CAPA instead of API, fix it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201209231352.6a9203094c1e.I658e63066b05257e78fc20bfcbcf151ba8fd7754@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-12-10iwlwifi: follow the new inclusive terminologyEmmanuel Grumbach
The new inclusive terminology requires to change a few terms that were used in iwlwifi. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201209231352.1eb4c8625f36.I1b17b68d4a8e77071da3e15ffbd902d15c1d4938@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-12-10iwlwifi: mvm: add support for 6GHzLuca Coelho
Add support to the 6GHz band (aka. Ultra High Band or UHB). This allows us to scan and connect to channels in that band, including all the relevant features, such as preferred scan channels, colocated channels etc. Co-developed-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Co-developed-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Ilan Peer <ilan.peer@intel.com> Co-developed-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Tova Mussai <tova.mussai@intel.com> Co-developed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Co-developed-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com> Signed-off-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com> Co-developed-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> Co-developed-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20201210000657.0fdbfc3d7352.Idb648536faf21716e2ab2c6d6890d3e49f719cd3@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-10-08iwlwifi: read and parse PNVM fileLuca Coelho
The driver looks for a PNVM file that contains FW configuration data for each different HW combination. The FW requests the data for a certain SKU_ID and the driver tries to find it in the PNVM file. Read the file, parse its contents and send it to the trans. Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201008181047.826bc607e57a.I1d93dd6e6651586878db57fac3e7c3f09d742c42@changeid
2020-10-08iwlwifi: mvm: get number of stations from TLVNathan Errera
FW is changing the max number of supported stations. To adapt to the change we get the max number from the TLV and act according to the new number. Signed-off-by: Nathan Errera <nathan.errera@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/iwlwifi.20201008180656.863ab470babc.I393223392f36436663c4e66add03fefe77b74e60@changeid
2020-10-01iwlwifi: mvm: add PROTECTED_TWT firmware APIShaul Triebitz
Add the PROTECTED_TWT bit to the MAC context data_policy enum. Define the PROTECTED_TWT TLV. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c80b994d6bf0.Ifd45dfd5066283886f969313c20ff81edde428ff@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2020-04-24iwlwifi: acpi: read TAS table from ACPI and send it to the FWMordechay Goodstein
Read the Time Averaged SAR (TAS) table from ACPI and if TAS feature is enabled in the FW send the black list countries which TAS is disabled in to the FW Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20200418110539.40a327d32cfd.I7203f3afc8186cca34c48a1a116baac1df5eff4e@changeid
2020-03-27iwlwifi: mvm: add soc latency supportShahar S Matityahu
Some devices require longer time to stabilize the power and XTAL. This is especially true for devices integrated in the SoC. Add support for a new firmware API that allows the driver to set the latency value accordingly. Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12 Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-11-05Merge tag 'wireless-drivers-next-2019-11-05' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.5 First set of patches for 5.5. The most active driver here clearly is rtw88, lots of patches for it. More quiet on other drivers, smaller fixes and cleanups all over. This pull request also has a trivial conflict, the report and example resolution here: https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au Major changes: rtw88 * add deep power save support * add mac80211 software tx queue (wake_tx_queue) support * enable hardware rate control * add TX-AMSDU support * add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support * add power tracking support * add 802.11ac beamformee support * add set_bitrate_mask support * add phy_info debugfs to show Tx/Rx physical status * add RFE type 3 support for 8822b ath10k * add support for hardware rfkill on devices where firmware supports it rtl8xxxu * add bluetooth co-existence support for single antenna iwlwifi * Revamp the debugging infrastructure ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-10-30iwlwifi: fw api: support new API for scan config cmdAyala Beker
The API was reduced to include only knowledge currently needed by the FW scan logic, the rest is legacy. Support the new, reduced version. Using the old API with newer firmwares (starting from iwlwifi-*-50.ucode, which implements and requires the new API version) causes an assertion failure similar to this one: [ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-10-25iwlwifi: rx: use new api to get band from rx mpduTova Mussai
The FW introduce new API to get the band from the rx mpdu, use this new API. Signed-off-by: Tova Mussai <tova.mussai@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-25iwlwifi: mvm: use the new session protection commandEmmanuel Grumbach
The firmware has now a new session protection command. This new API allows the firmware to manage the protection needed for association. It'll also remove the event when the association is complete. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-10-25iwlwifi: dbg_ini: add TLV allocation new API supportShahar S Matityahu
Add new debug TLVs API preprocessing. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: fw api: add DRAM buffer allocation commandShahar S Matityahu
Add support code to be able to use the DRAM buffer allocation command, which allows us to send information about a buffer to the firmware to use it with the DBGC hardware. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: add iwl_tlv_array_len()Shahar S Matityahu
Allows to easily calculate array length at the end of a TLV. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: mvm: add support for single antenna diversityHaim Dreyfuss
There are products which have a single chain with 2 antennas. In these products, we need to inform the FW that the device has the single antenna diversity(SAD) feature. In the future, we will read the active antenna from a BIOS configuration. Currently, we use a default configuration which means that the FW decides which antenna to use. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: dbg_ini: remove debug flow TLVShahar S Matityahu
Debug flow TLV was removed from the FW. Remove the TLV from the driver as well. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: support per-platform antenna gainGil Adam
TX power limits as defined in the OTP assume the worst case scenario in terms of the platform's atenna gain, but most platforms are below that value so they can use more TX power without passing the regulatory limit. If the platform indicates in the BIOS that it indeed has lower gain, and the geographic location allows it, higher TX power can be used. The driver reads the PPAG (Per-Platform Antenna Gain) data from BIOS (if it exists), validates it and sends the appropriate command to the FW. This flow happens once at FW init, in case of suspend/resume there is no need to read again from BIOS as we save those values during init, so just send the PPAG command again to FW. Signed-off-by: Gil Adam <gil.adam@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: scan: add support for new scan request command versionAyala Beker
Scan API was changed to support 6Ghz channels as well. Support the new version. Signed-off-by: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-09-06iwlwifi: LTR updatesAlex Malamud
New FW versions introduces LTR feature enablement by default. For such FW versions, driver (mvm/xvt) should not send host command to enable LTR feature, also it should be possible to override LTR configuration through the debugfs. 1. Send LTR feature enablement command only for FW versions which does not advertises SET_LTR_GEN2 capability. 2. Implement ltr_config file in debugfs for LTR configuration override. Signed-off-by: Alex Malamud <alex.malamud@intel.com>
2019-09-06iwlwifi: dbg: support debug recording suspend resume commandShahar S Matityahu
Support the new DBGC_SUSPEND_RESUME command to change the recording state. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: Add support for SAR South Korea limitationHaim Dreyfuss
South Korea is adding a more strict SAR limit called "Limb SAR". Currently, WGDS SAR offset group 3 is not used (not mapped to any country). In order to be able to comply with South Korea new restriction: - OEM will use WGDS SAR offset group 3 to South Korea limitation. - OEM will change WGDS revision to 1 (currently latest revision is 0) to notify that Korea Limb SAR applied. - Driver will read the WGDS table and pass the values to FW (as usual) - Driver will pass to FW an indication that Korea Limb SAR is applied in case table revision is 1. Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: fw api: support adwell HB default APs number apiShahar S Matityahu
Support adaptive dwell high band default number of APs new api. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-06-29iwlwifi: dbg_ini: support debug info TLVShahar S Matityahu
Add support to debug info TLV. The TLV contains human readable naming of the FW image and the debug configuration. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-05-05Merge tag 'wireless-drivers-next-for-davem-2019-05-03' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.2 Most likely the last patchset of new feature for 5.2, and this time we have quite a lot of new features. Most obvious being rtw88 from Realtek which supports RTL8822BE and RTL8822CE 802.11ac devices. We have also new hardware support for existing drivers and improvements. There's one conflict in iwlwifi, my example conflict resolution below. Major changes: iwlwifi * bump the 20000-series FW API version * work on new hardware continues * RTT confidence indication support for Fine Timing Measurement (FTM) * an improvement in HE (802.11ax) rate-scaling * add command version parsing from the fimware TLVs * add support for a new WoWLAN patterns firmware API rsi * add support for rs9116 mwifiex * add support for SD8987 brcmfmac * add quirk for ACEPC T8 and T11 mini PCs rt2x00 * add RT3883 support qtnfmac * fix debugfs interface to support multiple cards rtw88 * new driver mt76 * share more code across drivers * add support for MT7615 chipset * rework DMA API * tx/rx performance optimizations * use NAPI for tx cleanup on mt76x02 * AP mode support for USB devices * USB stability fixes * tx power handling fixes for 76x2 * endian fixes Conflicts: There's a trivial conflict in drivers/net/wireless/intel/iwlwifi/fw/file.h, just leave IWL_UCODE_TLV_FW_FSEQ_VERSION to the file. 'git diff' output should be just empty: diff --cc drivers/net/wireless/intel/iwlwifi/fw/file.h index cd622af90077,b0671e16e1ce..000000000000 --- a/drivers/net/wireless/intel/iwlwifi/fw/file.h +++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three trivial overlapping conflicts. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-29iwlwifi: parse command version TLVJohannes Berg
In newer firmware images there's a command version TLV that states, for each listed command or notification, which version of the command and/or notification structure is used. Read and keep this data to be able to use it in the future. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: support fseq tlv and print fseq versionShahar S Matityahu
Support fseq tlv and print fseq version to dmesg. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-29iwlwifi: mvm: support v2 of the WoWLAN patterns commandLuca Coelho
Add new definitions for the WoWLAN patterns API version 2 and support for version 2 of the WoWLAN patterns command without implementing the new features. With this commit we only supporting the existing bitmask pattern match. Use the new version only if the TLV is set. Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-19iwlwifi: mvm: support rtt confidence indicationAvraham Stern
The range response notification API has changed to add a value that indicates the confidence of the rtt result. Support the new API and print the rtt confidence for debug. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-18iwlwifi: dbg_ini: check debug TLV type explicitlyShahar S Matityahu
In ini debug TLVs bit 24 is set. The driver relies on it in the memory allocation for the debug configuration. This implementation is problematic in case of a new debug TLV that is not supported yet is added and uses bit 24. In such a scenario the driver allocate space without using it which causes errors in the apply point enabling flow. Solve it by explicitly checking if a given TLV is part of the list of the supported ini debug TLVs. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: f14cda6f3b31 ("iwlwifi: trans: parse and store debug ini TLVs") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-04-03iwlwifi: mvm: support HE context cmd API changeSara Sharon
Support API change to pass all mbssid parameters to the firmware. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-03-22iwlwifi: mvm: Support new format of SCAN_OFFLOAD_PROFILES_QUERY_RSPIlan Peer
Newer FWs use a new format of the SCAN_OFFLOAD_PROFILES_QUERY_RSP, which now supports indicating match on an higher number of channels. Modify the code to support both the old format and the newer one, based on a FW TLV. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-03-22iwlwifi: support new NVM response APIShaul Triebitz
Support REGULATORY_NVM_GET_INFO_RSP_API_S_VER_4. This API adds the new 6-7GHz channels. Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-03-22iwlwifi: mvm: track CSA beaconsSara Sharon
Send to FW modify command for every beacon we receive during channel switch. FW will track the count, and make sure the event is scheduled in time even if AP changed count. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-14iwlwifi: mvm: add support for new FTM fw APIAvraham Stern
The FTM new API uses API TLV bit 15. The driver mistakenly uses this bit for beacon filter API, although no TLV was assigned for the beacon filter API. For now, make beacon filter use bit 16 instead (not set by the fw anyway). Once a TLV is assigned to the beacon filter API it should be updated. Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-14iwlwifi: add FW recovery flowMordechay Goodstein
Add new API and TLV for the ability to send commands in the beginning and end of reset flow. The full flow of recovery is: 1. While loading FW, get address (from the TLV) of target buffer to read in case of reset 2. If an error/assert happens read the address data from step 1. 3. Reset the HW and load the FW. 4. Send the data read in step 2. 5. Add station keys 6. Send notification to FW that reset flow is done. The main use of the recovery flow is for support in PN/SN recovery when offloaded Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-14iwlwifi: receive umac and lmac error table addresses from TLVsShahar S Matityahu
TLV 54 holds umac debug related addresses. TLV 55 holds lmac debug related addresses. These TLVs aim to replace the alive notification data in the future. Parse and keep error table addresses received from the TLVs for both lmac and umac and use these addresses instead of the pointer received from alive notification. The feature supports only unified image. Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-14iwlwifi: mvm: support FTM responderJohannes Berg
Add support for FTM responder for hardware/firmware combinations that advertise support for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-04iwlwifi: mvm: support absolute thresholds in bf configurationAvigail Grinstein
Update iwl_beacon_filter_cmd to support BEACON_FILTER_CONFIG_API_S_VER_4. Currently driver configs them to be zero (i.e. disable them, so no change is applied). Signed-off-by: Avigail Grinstein <avigail.grinstein@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-04iwlwifi: mvm: support new format for the beacon notificationEmmanuel Grumbach
The firmware is changing the format of the beacon notification to remove the dependency on the Tx response format. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2019-02-04iwlwifi: mvm: support CHANNEL_SWITCH_TIME_EVENT_CMD commandSara Sharon
When we do channel switch, we used to schedule time events ourselves. This was offloaded to FW. Support the new command and flow. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 22:07:21 +0000