summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wil6210/pcie_bus.c
AgeCommit message (Collapse)Author
2015-08-06wil6210: remove 3-MSI supportVladimir Kondratiev
In the recent kernel versions, multiple MSI is not well supported. In particular, it is not supported on x86 and ARM architectures. Also, internal interrupt handling logic is simpler and more effective when using single interrupt. Remove support for 3 MSI, convert module parameter "use_msi" from int with range [0,1,3] to boolean. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: reorder init sequenceVladimir Kondratiev
Need to reorder init sequence to run wil_platform_init before pci_enable_device. Assumption is platform init may be required before device may be enabled. Another issue, platform uninit should be called after pci_disable_device because platform uninit may render pci device non-accessible. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-06-09wil6210: platform hooks for modile init/exitVladimir Kondratiev
Provide platform hooks for module init/exit. If platform require to perform some specific actions in global context, this is where to do so. Example may be turning on power for the PCIE based on DT information. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-04-28wil6210: fw debug modeVladimir Kondratiev
refactor module parameter debug_fw to act as "fw debug mode", where driver do nothing but allow card memory access. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-03-20wil6210: fix check for FW responsivenessVladimir Kondratiev
"echo" used to be called when no firmware loaded to the NIC, this causes error output. Probe firmware with "echo" only after it returned "ready" event. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-02-27wil6210: remove support for old hardwareVladimir Kondratiev
Hardware older than Sparrow B0 obsolete. There is no WiFi product that uses this hardware. Recent firmware does not support it either. Remove driver support. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-02-27wil6210: boot loaderVladimir Kondratiev
Introduce boot loader. Instead of the operational firmware, very small boot loader is burned to the on-board flash. Boot loader initializes hardware upon reset, and prepares for low power mode. Boot loader reports MAC address and detects radio chip connected. Driver loads firmware only when bringing up interface. All information required to set up network interface, most important is MAC address, reported by the boot loader The firmware composed of 2 files: - wil6210.fw - firmware itself (compiled code + data) - wil6210.board - board file (various board and radio dependent calibrations and parameters) Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-01-15wil6210: add advanced interrupt moderationVladimir Kondratiev
Add advanced interrupt moderation support available since "Sparrow B0". Legacy interrupt moderation used only one counter to moderate tx, rx, and misc interrupts. Advanced interrupt moderation bypasses misc, and handles separately tx and rx interrupts. In addition it has two timers for each interrupt type. Max burst duration timer which defines how long to postpone interrupt after first event (receive event for rx and tx complete event for tx), and interframe timeout which defines how to determine the end of the burst and issue interrupt even if the first timer still pending. Capabilities flags in wil_priv is set on initialization according to HW. The rest of the code checks for advanced interrupt capability bit in capabilities flags field. Debugfs is split accordingly: "legacy" interrupt moderation remains unchanged, new debugs files added for advanced interrupt moderation support. Module params are aligned to support advanced interrupt moderation (tx & rx). When not available (for legacy interrupt moderation) will use only rx configuration; Tx configuration will be ignored in this case. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-01-15wil6210: use HW capabilities mask in resetVladimir Kondratiev
Use the proper reset follow based on HW capabilities detection instead of chip ID. Remove old hw ID mechanism which was used only for reset flow. Remove support for Marlon A0. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-01-15wil6210: detect HW capabilitiesVladimir Kondratiev
Read relevant information (HW ID for now) once on init and set capabilities accordingly. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2014-09-11wil6210: fix for oops while stopping interfaceVladimir Kondratiev
When interface stopped while running intensive Rx traffic, the following oops observed: [89846.734683] Call trace: [89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358 [89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4 [89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210] wil_netif_rx_any [89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210] wil_release_reorder_frame [89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210] [89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210] [89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210] [89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210] [89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc [89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330 [89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8 [89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882) [89846.807008] ---[ end trace d6fdc17cd27d18f6 ]--- Reason is the following: when removing Rx vring (wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini), Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps (already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer. Then, network stack trying to access this buffer and fails. Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects NAPI enablement state, check it when triggering Rx NAPI. Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message get printed - in this case kernel oops would be observed. Original oops is no more reproducible. This change requires also changes in the AP flows. Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled when resetting target. For this, promote __wil_up() and __wil_down() to the module scope, and use it in the relevant flows. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: fix for memory corruption upon rmmodDedy Lansky
Driver disabled PCI master before making sure HW is idle. This caused memory corruption in case HW access system memory after PCI master got disabled. The fix is to change uninit sequence. Make sure FW/HW is idle before disabling PCI Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: add more debug printoutsVladimir Kondratiev
added misc printouts in some init/uninit functions for better traceability Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: platform specific moduleVladimir Kondratiev
New module (wil_platform) for handling platform specific tasks Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-08-25wil6210: fix access after free in wil_pcie_remove()Vladimir Kondratiev
'wil' released in wil_if_free(); save iomapped address aside to properly unmap it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-08-25wil6210: Workaround for Sparrow with bad device idVladimir Kondratiev
If firmware broken on the boot time, Sparrow card enumerates as device 0x302 instead of 0x310. Allow using this ID Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-08-25wil6210: update copyright year 2014Vladimir Kondratiev
Fix Copyright headers in all files changed in 2014, to mention 2014 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-07-18wil6210: support for "sparrow" hardwareVladimir Kondratiev
New hardware release appears; it require some changes to properly support it. Introduce struct wil_board and "board" attribute in wil6210_priv; keep hardware variant information in this structure. fill it on probe(). Used in the reset flow. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-06-19wil6210: work around for platforms with broken INTxVladimir Kondratiev
There are platforms where INTx can't be routed by ACPI, this leads to pci_enable_device failure. Re-try pretending we have MSI already configured; in this case pci_enable_device do not try to configure INTx. However, MSI could still work. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-06-19wil6210: remove unused #includeVladimir Kondratiev
In the pcie_bus.c, knowledge about debugfs is not necessary Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-06-19wil6210: Allow driver load if FW not readyVladimir Kondratiev
Usable for debugging, to be able to obtain FW traces Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-29wil6210: improve pointers printingVladimir Kondratiev
use proper format %pad for the dma_addr_t arguments; prefix %p with 0x, as %p don't print is by itself Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: fix printouts for better readabilityVladimir Kondratiev
Reshuffle prints to consolidate firmware/hardware information report upon card init Convert print for unhandled MISC ISR bits to "debug" - it is normal situation and not an "error" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-21Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2014-03-17wil6210: fix race between disconnect and Tx NAPIVladimir Kondratiev
When disconnecting some CID, corresponded Tx vring get released. During vring release, all descriptors get freed. It is possible that Tx NAPI working on the same vring simultaneously. If it happens, descriptor may be double freed. To protect from the race above, make sure NAPI won't process the same vring. Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if 'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI get synchronized. NAPI enablement status protected by wil->mutex, add protection where it was missing and check for it. During reset, disconnect all peers first, then proceed with the Rx vring. It allows for the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about connection status change Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix for HW bug in interrupt setup logicVladimir Kondratiev
Hardware bug triggered by the MSI init while INTx asserted for some reason. De-assert INTx prior to MSI set-up Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: update target reset to support new HWVladimir Kondratiev
Support for new chip revision. Revision read from the internal register, PCIE config's "revision id" register do not indicate HW version properly Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-02-18wil6210: Use pci_enable_msi_range() instead of pci_enable_msi_block()Alexander Gordeev
As result of deprecation of MSI-X/MSI enablement functions pci_enable_msix() and pci_enable_msi_block() all drivers using these two interfaces need to be updated to use the new pci_enable_msi_range() and pci_enable_msix_range() interfaces. Signed-off-by: Alexander Gordeev <agordeev@redhat.com> Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: wil6210@qca.qualcomm.com Cc: netdev@vger.kernel.org Cc: linux-pci@vger.kernel.org Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-09-26wireless: wil6210: remove unnecessary pci_set_drvdata()Jingoo Han
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: headers clean-upVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: fix checkpatch CamelCase warningsVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: remove raw wil_dbg() callsVladimir Kondratiev
Introduce debug category "MISC", convert all raw wil_dbg() to this category. This improves dynamic debug manageability Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-04wireless: add new wil6210 802.11ad 60GHz driverVladimir Kondratiev
This adds support for the 60 GHz 802.11ad Wilocity card through a new driver, wil6210. Wilocity implemented the firmware, QCA maintains the device driver. Currently supported: - STA: with security - AP: limited to 1 connected STA, security disabled - Monitor: due to a hardware/firmware limitation either control or non-control frames are monitored Using a STA and AP with this drive, one can assemble a fully functional BSS. Throughput of 1.2Gbps is achieved with iperf. The wil6210 cards have on-board flash memory for the firmware, the cards comes pre-flashed and no firmware download is required. For more details see: http://wireless.kernel.org/en/users/Drivers/wil6210 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 19:50:48 +0000