summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/wcn36xx
AgeCommit message (Collapse)Author
2017-05-23wcn36xx: Close SMD channel on device removalBjorn Andersson
The SMD channel is not the primary WCNSS channel and must explicitly be closed as the device is removed, or the channel will already by open on a subsequent probe call in e.g. the case of reloading the kernel module. This issue was introduced because I simplified the underlying SMD implementation while the SMD adaptions of the driver sat on the mailing list, but missed to update these patches. The patch does however only apply back to the transition to rpmsg, hence the limited Fixes. Fixes: 5052de8deff5 ("soc: qcom: smd: Transition client drivers from smd to rpmsg") Reported-by: Eyal Ilsar <c_eilsar@qti.qualcomm.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-20Merge tag 'mac80211-next-for-davem-2017-04-18' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== My last pull request has been a while, we now have: * connection quality monitoring with multiple thresholds * support for FILS shared key authentication offload * pre-CAC regulatory compliance - only ETSI allows this * sanity check for some rate confusion that hit ChromeOS (but nobody else uses it, evidently) * some documentation updates * lots of cleanups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-09Merge tag 'wireless-drivers-next-for-davem-2017-04-07' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 4.12 Lots of bugfixes as usual but also some new features. Major changes: ath10k * improve firmware download time for QCA6174 and QCA9377, especially helps resume time ath9k_htc * add support AirTies 1eda:2315 AR9271 device rt2x00 * add support MT7620 mwifiex * enable auto deep sleep mode for USB chipsets brcmfmac * add support for network namespaces (WIPHY_FLAG_NETNS_OK) ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-28soc: qcom: smd: Transition client drivers from smd to rpmsgBjorn Andersson
By moving these client drivers to use RPMSG instead of the direct SMD API we can reuse them ontop of the newly added GLINK wire-protocol support found in the 820 and 835 Qualcomm platforms. As the new (RPMSG-based) and old SMD implementations are mutually exclusive we have to change all client drivers in one commit, to make sure we have a working system before and after this transition. Acked-by: Andy Gross <andy.gross@linaro.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09wcn36xx: Fix error handlingChristophe Jaillet
Reorder 'out_free_dxe_pool' and 'out_free_dxe_ctl' error handling labels in order to match the way resources have been allocated. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-03-06wireless: Set NL80211_EXT_FEATURE_CQM_RSSI_LIST in multiple driversAndrew Zaborowski
Set the NL80211_EXT_FEATURE_CQM_RSSI_LIST wiphy extended feature wholesale in all mac80211-based drivers that do not set the IEEE80211_VIF_BEACON_FILTER flags on their interfaces. mac80211 will be processing supplied RSSI values in ieee80211_rx_mgmt_beacon and will detect when the thresholds set by ieee80211_set_cqm_rssi_range_config are crossed. Remaining (few) drivers need code to enable the firmware to monitor the thresholds. This is mostly only compile-tested. Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-02-07wcn36xx: Implement cancel_hw_scanBjorn Andersson
In the even that the wcn36xx interface is brought down while a hw_scan is active we must abort and wait for the ongoing scan to signal completion to mac80211. Reported-by: Mart Raudsepp <leio@gentoo.org> Fixes: 886039036c20 ("wcn36xx: Implement firmware assisted scan") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Don't use the destroyed hal_mutexBjorn Andersson
ieee80211_unregister_hw() might invoke operations to stop the interface, that uses the hal_mutex. So don't destroy it until after we're done using it. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Implement print_reg indicationBjorn Andersson
Some firmware versions sends a "print register indication", handle this by printing out the content. Cc: Nicolas Dechesne <ndec@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Implement firmware assisted scanBjorn Andersson
Using the software based channel scan mechanism from mac80211 keeps us offline for 10-15 second, we should instead issue a start_scan/end_scan on each channel reducing this time. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-12wcn36xx: Transition driver to SMD clientBjorn Andersson
The wcn36xx wifi driver follows the life cycle of the WLAN_CTRL SMD channel, as such it should be a SMD client. This patch makes this transition, now that we have the necessary frameworks available. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Silence error about unsupported smd event 188Bjorn Andersson
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently ignore this message so let's do the same to silence the error message. Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Fix up wcn36xx_smd_update_scan_params()Bjorn Andersson
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient versions of the firmware and support actually specifying the list of channels. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Correct DXE chip version differentiationBjorn Andersson
The CCU block in WCNSS is configured for appropriate routing of interrupts from the DXE to the application cpu, this is not dependant on the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva or pronto built in. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Split mmio space into explicit regionsBjorn Andersson
Split the wcnss mmio space into explicit regions for ccu and dxe and acquire these from the node referenced by the qcom,mmio phandle. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Change indication list lock to spinlockBjorn Andersson
In preparation for handling incoming messages from IRQ context, change the indication list lock to a spinlock Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-07-08wcn36xx: Fold indication payload into message headerBjorn Andersson
Merge the two allocation instead of separately allocating room for the indication payload. Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-27wcn36xx: Set SMD timeout to 10 secondsBjorn Andersson
After booting the wireless subsystem and uploading the NV blob to the WCNSS_CTRL service the remote continues to do things and will not start servicing wlan-requests for another 2-5 seconds (measured). The downstream code does not have any special handling for this case, but has a timeout of 10 seconds for the communication layer. By extending the wcn36xx timeout to match this we follows the same flow for the boot procedure and can successfully configure WiFi as wlan0 is registered. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-26Merge ath-next from ath.gitKalle Valo
ath.git patches for 4.7. Major changes: ath10k * implement set_tsf() for 10.2.4 branch * remove rare MSI range support * remove deprecated firmware API 1 support ath9k * add module parameter to invert LED polarity wcn36xx * fixes to get the driver properly working on Dragonboard 410c
2016-04-25wcn36xx: Fill in capability listBjorn Andersson
Fill in the capability list with more values from the downstream driver. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Correct remove bss key response encodingBjorn Andersson
The WCN36XX_HAL_RMV_BSSKEY_RSP carries a single u32 with "status", so we can use the standard status check function for decoding the result. This is the last user of the v2 status checker, so remove the struct and helper function. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Delete BSS before idling linkBjorn Andersson
When disabling the beacon we must delete the bss before idling the link. Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Use correct command struct for EXIT_BMPS_REQPontus Fuchs
EXIT_BMPS_REQ was using the command struct for ENTER_BMPS_REQ. I spotted this when looking at command dumps. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Implement multicast filteringPontus Fuchs
Pass the multicast list to FW. This patch also adds a way to build the smd command in place. This is needed because the MC list command is too big for the stack. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> [bjorn: dropped FIF_PROMISC_IN_BSS usage] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Track association statePontus Fuchs
Knowing the association state is needed for mc filtering. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Clear encrypt_type when deleting bss keyPontus Fuchs
This fixes a problem connecting to an open network after being connected to an encrypted network. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Use allocated self sta index instead of hard codedPontus Fuchs
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Copy all members in config_sta v1 conversionPontus Fuchs
When converting to version 1 of the config_sta struct not all members where copied. This fixes the problem of multicast frames not being delivered on an encrypted network. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Parse trigger_ba response properlyPontus Fuchs
This message does not follow the canonical format and needs it's own parser. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Remove sta pointer in private vif structPontus Fuchs
This does not work with multiple sta's in a vif. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Fetch private sta data from sta entry instead of from vifPontus Fuchs
For consistency with other code. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Add helper macros to cast sta to privPontus Fuchs
While poking at this I also change two related things. I rename one variable to make the names consistent. I also move one assignment of priv_sta to the declaration to save a few lines. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Use define for invalid index and fix typoPontus Fuchs
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Use consistent name for private vifPontus Fuchs
Some code used priv_vif and some used vif_priv. Convert all to vif_priv for consistency. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Add helper macros to cast vif to private vif and vice versaPontus Fuchs
Makes the code a little easier to read. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Pad TIM PVM if neededPontus Fuchs
The wcn36xx FW expects a fixed size TIM PVM in the beacon template. If supplied with a shorter than expected PVM it will overwrite the IE following the TIM. Squashed with fix from Jason Mobarak <jam@cozybit.com>: Patch "wcn36xx: Pad TIM PVM if needed" has caused a regression in mesh beaconing. The field tim_off is always 0 for mesh mode, and thus pvm_len (referring to the TIM length field) and pad are both incorrectly calculated. Thus, msg_body.beacon_length is incorrectly calculated for mesh mode. Fix this. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Jason Mobarak <jam@cozybit.com> [bjorn: squashed in Jason's fixup] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-25wcn36xx: Clean up wcn36xx_smd_send_beaconPontus Fuchs
Needed for coming improvements. No functional changes. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> [bjorn: restored BEACON_TEMPLATE_SIZE define to 0x180] Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-12cfg80211: remove enum ieee80211_bandJohannes Berg
This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: allow not sending MIC up from driver for HW cryptoSara Sharon
When HW crypto is used, there's no need for the CCMP/GCMP MIC to be available to mac80211, and the hardware might have removed it already after checking. The MIC is also useless to have when the frame is already decrypted, so allow indicating that it's not present. Since we are running out of bits in mac80211_rx_flags, make the flags field a u64. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-01-14mac80211: pass block ack session timeout to to driverSara Sharon
Currently mac80211 does not inform the driver of the session block ack timeout when starting a rx aggregation session. Drivers that manage the reorder buffer need to know this parameter. Seeing that there are now too many arguments for the drv_ampdu_action() function, wrap them inside a structure. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-01-07wcn36xx: split DMA mask register writing.Fengwei Yin
Per comments from Bjorn Andersson <bjorn.andersson@sonymobile.com>, split DMA mask register writing as seperate patch in case we need bi-sect in the furture. Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-01-07wcn36xx: handle rx skb allocation failure to avoid system crashFengwei Yin
Lawrence reported that git clone could make system crash on a Qualcomm ARM soc based device (DragonBoard, 1G memory without swap) running 64bit Debian. It's turned out the crash is related with rx skb allocation failure. git could consume more than 600MB anonymous memory. And system is in extremely memory shortage case. But driver didn't handle the rx allocation failure case. This patch doesn't submit skb to upper layer if rx skb allocation fails. Instead, it reuse the old skb for rx DMA again. It's more like drop the packets if system is in memory shortage case. With this change, git clone is OOMed instead of system crash. Reported-by: King, Lawrence <lking@qti.qualcomm.com> Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-11-30wcn36xx: use new response format for wcn3620 remove_bsskeyAndy Green
On wcn3620, firmware response to remove_bsskey uses the new, larger "v2" format Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-11-30wcn36xx: use new response format for wcn3620 trigger_baAndy Green
On wcn3620, firmware response to trigger_ba uses the new, larger "v2" format Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-11-30wcn36xx: handle new hal response formatAndy Green
wcn3620 has a new message structure for the reply to some hal commands. This patch adds the struct and helper routine that uses it if the chip is wcn3620, or falls back to the old helper routine. We don't know what to do with the candidate list he sends back, but we can at least accept and ignore it nicely instead of dying. Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-11-30wcn36xx: swallow two wcn3620 IND messagesAndy Green
WCN3620 can asynchronously send two new kinds of indication message, since we can't handle them just accept them quietly. Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-11-30wcn36xx: introduce WCN36XX_HAL_AVOID_FREQ_RANGE_INDAndy Green
WCN3620 firmware introduces a new async indication, we need to add it as a known message type so we can accept it Signed-off-by: Andy Green <andy.green@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-10-28wcn36xx: Remove warning message when dev is NULL for arm64 dma_alloc.yfw
arm64 has requirement that all the dma operations have actual device. Otherwise, following warnning message shown and dma allocation fails: WARNING: CPU: 0 PID: 954 at arch/arm64/mm/dma-mapping.c:106 __dma_alloc+0x24c/0x258() Use an actual device structure for DMA allocation Modules linked in: wcn36xx wcn36xx_platform CPU: 0 PID: 954 Comm: ifconfig Not tainted 4.0.0+ #14 Hardware name: Qualcomm Technologies, Inc. MSM 8916 MTP (DT) Call trace: [<ffffffc000089904>] dump_backtrace+0x0/0x124 [<ffffffc000089a38>] show_stack+0x10/0x1c [<ffffffc000627114>] dump_stack+0x80/0xc4 [<ffffffc0000b2e64>] warn_slowpath_common+0x98/0xd0 [<ffffffc0000b2ee8>] warn_slowpath_fmt+0x4c/0x58 [<ffffffc00009487c>] __dma_alloc+0x248/0x258 [<ffffffbffc009270>] wcn36xx_dxe_allocate_mem_pools+0xc4/0x108 [wcn36xx] [<ffffffbffc0079c4>] wcn36xx_start+0x38/0x240 [wcn36xx] [<ffffffc0005f161c>] ieee80211_do_open+0x1b0/0x9a4 [<ffffffc0005f1e68>] ieee80211_open+0x58/0x68 [<ffffffc00051693c>] __dev_open+0xb0/0x120 [<ffffffc000516c10>] __dev_change_flags+0x88/0x150 [<ffffffc000516cf4>] dev_change_flags+0x1c/0x5c [<ffffffc000570950>] devinet_ioctl+0x644/0x6f0 Signed-off-by: Yin, Fengwei <fengwei.yin@linaro.org> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-10-28wcn36xx: introduce per-channel ring buffer locksBob Copeland
wcn36xx implements a ring buffer for transmitted frames for each (high and low priority) DMA channel. The ring buffers are lockless: new frames are inserted at the head of the queue, while finished packets are reaped from the tail. Unfortunately, the list manipulations are missing any kind of barriers so are susceptible to various races: for example, a TX completion handler might read an updated desc->ctrl before the head has actually advanced, and then null out the ctl->skb pointer while it is still being used in the TX path. Simplify things here by adding a spin lock when traversing the ring. This change increased stability for me without adding any noticeable overhead on my platform (xperia z). Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-31 15:16:52 +0000