| Age | Commit message (Collapse) | Author |
|---|
|
we don't have here any ieee80211_hw dependencies any way.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Track it per channel context instead of in the softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The "goto chip_reset" is a bit misleading, because it does not actually
issue a chip reset. Instead it is bypassing processing of other
interrupts and assumes that the tasklet will issue a chip reset.
In the case of RXORN this does not happen, so bypassing processing of
other interrupts will simply allow them to fire again. Even if RXORN
was triggering a reset, it is not critical enough to need the bypass
here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mac80211 currently has a race which can be hit
with this sequence:
* Start a scan operation.
* TX BA is initiated by ieee80211_start_tx_ba_session().
* Driver sets up internal state and calls
ieee80211_start_tx_ba_cb_irqsafe().
* mac80211 adds a packet to sdata->skb_queue with
type IEEE80211_SDATA_QUEUE_AGG_START.
* ieee80211_iface_work() doesn't process the
packet because scan is in progress.
* ADDBA response timer expires and the sta/tid is
torn down.
* Driver receives BA stop notification and calls
ieee80211_stop_tx_ba_cb_irqsafe().
* This is also added to the queue by mac80211.
* Now, scan finishes.
At this point, the queued up packets might be processed
if some other operation schedules the sdata work. Since
the tids have been cleaned up already, warnings are hit.
If this doesn't happen, the packets are left in the queue
until the interface is torn down.
Since initiating a BA session when scan is in progress
leads to flaky connections, especially in MCC mode, we
can drop the TX BA request. This improves connectivity
with legacy clients in MCC mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The flush timeout in MCC mode is very small, since
we are constrained by the time slice for each
channel context, but since only the HW queues are
flushed when switching contexts, it is acceptable.
Since the SW queues are also emptied in the mac80211 flush()
callback, a larger duration is needed. Add an override
argument to __ath9k_flush() and set it when flush()
is called in MCC mode. This allows the driver to
drain both the SW and HW queues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of using ATH_CHANCTX_EVENT_ASSIGN to abort
a HW scan when a new interface becomes active, use the
mgd_prepare_tx() callback. This allows us to make
sure that the GO's channel becomes operational by
using flush_work().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a GO interface is active when we receive a
mgd_prepare_tx() call, then we need to send
out a new NoA before switching to a new context.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since both the arguments need to satisfy
the alignment requirements of ether_addr_copy(),
use memcpy() in cases where there will be no
big performance benefit and make sure that
ether_addr_copy() calls use properly aligned
arguments.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ATH_CHANCTX_EVENT_AUTHORIZED is required to trigger
the MCC scheduler when a station interface becomes
authorized. But, since the driver gets station state
notifications when the current operating mode is AP
too, make sure that we send ATH_CHANCTX_EVENT_AUTHORIZED
only when the interface is in station mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pending frames in the driver can be present
either in the HW queues or SW. ath9k_has_pending_frames()
currently checks for the HW queues first and then
checks if any ACs are queued in the driver.
In MCC mode, we need to check the HW queues alone, since
the SW queues are just marked as 'stopped' - they will
be processed in the next context switch. But since we
don't differentiate this now, mention whether we want
to check if there are frames in the SW queues.
* The flush() callback checks both HW and SW queues.
* The tx_frames_pending() callback does the same.
* The call to __ath9k_flush() in MCC mode checks HW queues alone.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The timeout value for flushing the TX queues
is hardcoded at 200ms right now. Use a channel
context-specific value instead to allow adjustments
to the timeout in case MCC is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a chip reset is done, all running timers,
tasklets etc. are stopped but the beacon tasklet
is left running. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a HW reset is done, the interrupt tasklet is
disabled before ISRs are disabled in the HW. This
allows a small window where the HW can still generate
interrupts. Since the tasklet is disabled and not killed,
it is not scheduled but deferred for execution at a later
time.
This happens because ATH_OP_HW_RESET is not set when ath_reset()
is called. When the hw_reset_work workqueue is used, this
problem doesn't arise because ATH_OP_HW_RESET is set
and the ISR bails out.
Set ATH_OP_HW_RESET properly in ath_reset() to avoid
this race - all the ath_reset_internal() callers have
been converted to use ath_reset() in the previous patch.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of having ath_reset_internal() and ath_reset()
as two separate calls to perform a HW reset, have
one function. This makes sure that the behavior will
be the same at all callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In MCC mode, currently the decision to enable
the multi-channel state machine is done
based on the association status if one of
the interfaces assigned to a context is in
station mode.
This allows the driver to switch to the other
context before the current station is able to
complete the 4-way handshake in case it is
required and this causes problems.
Instead, enable multi-channel mode when the
station moves to the authorized state. This
disallows an early switch to the other channel.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of using the sta_add()/sta_remove() callbacks,
use the sta_state() callback since this gives
more fine-grained control.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Enabling HW queue control for normal (non-mcc) mode
causes problems with queue management, resulting
in traffic stall. Since it is mainly required for
fairness in MCC mode, disable it for the general case.
Bug: https://dev.openwrt.org/ticket/18164
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When a channel context is removed, the hw_queue_base
is set to -1, this will result in a panic because
ath9k_chanctx_stop_queues() can be called on an interface
that is not assigned to any context yet - for example,
when trying to scan.
Fix this issue by setting the hw_queue_base to zero
when a channel context is removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
When a full chip reset is done, all the queues
across all VIFs are stopped, but if MCC is enabled,
only the queues of the current context is awakened,
when we complete the reset.
This results in unfairness for the inactive context.
Since frames are queued internally in the driver if
there is a context mismatch, we can awaken all the
queues when coming out of a reset.
The VIF-specific queues are still used in flow control,
to ensure fairness when traffic is high.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Change the ath9k_chanctx_wake_queues() API so
that we can pass the channel context that needs its
queues to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When draining of the TX queues fails, a
full HW reset is done. ath_reset() makes sure
that the queues in mac80211 are restarted,
so there is no need to wake them up again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_has_tx_pending() can be used to
check if there are pending frames instead
of having duplicate code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Checking for the queue depth outside of
the TX queue lock is incorrect and in this
case, is not required since it is done inside
ath9k_has_pending_frames().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is no need to check if the current
channel context has active ACs queued up
if the TX queue is not empty.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When multiple channel contexts are enabled, a p2p interface
that is assigned to a context will have an address that
is different from the device mac address, which is used
by wpa_s as the p2p device ID.
Certain frames like provision requests use the device address
and these get dropped since ath9k_calculate_summary_state()
iterates over only the active interfaces in a context and the
device address is not used.
Fix this by adding the device mac address to the bssid mask.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using the BSS information stored in mac80211 directly
is racy in certain conditions. For example, in a MCC
setup, if the scheduler is switching channels when
a local deauth is issued, calculation of the opmode/bssid
etc. is incorrect. To avoid this, store the bss params
in the driver and use it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ah struct might not have been initialized when
interrupt comes so check for it.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Initialize neighbor linked list used by dynack to compute ACK timeout
as the maximum STA ACK timeout
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Enable ACK timeout estimation algorithm if set_coverage_class routine has been
called with negative coverage_class parameter. Dynack is automatically disabled
setting valid value for coverage class
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Assign 'primary_sta' to the active primary station
interface after iterating over the list of interfaces.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The opmode is verified to be NL80211_IFTYPE_STATION
before calling ath9k_set_assoc_state().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When switching offchannel, BSS related information
in the HW has to be reset to default values. Add a routine
to do this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reduces code duplication.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, the interface count is maintained globally,
but this causes problems in RX filter calculation.
Make the interface count a per-channel-context variable
to fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Maintain the RX filter on a per-channel-context
basis and not globally. Not doing so was resulting
in incorrect filter calculation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since ath_startrecv() doesn't return an error value,
cleanup the callsites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If multiple channel contexts are active, then the opmode
can be different in each context. Since the RX filter is
calculated in ath_startrecv() before switching to the
new opmode, the wrong filters are chosen.
Fix this by calling ath9k_calculate_summary_state() before
the RX module is started.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a station interface is already assigned to a context
and is active and a second interface of type AP is added,
then beaconing on the new interface has to be begin only
after the BSS_CHANGED_BEACON_ENABLED flag is sent by mac80211
to the driver.
But, since we issue ATH_CHANCTX_EVENT_ENABLE_MULTICHANNEL as soon
as a new channel context is added, a switch occurs almost immediately
before BSS_CHANGED_BEACON_ENABLED is received. When a HW reset
is done for the new context, beacons are enabled for the
interface since "enable_beacon" in the BSS config maintained
in mac80211 is true - but the driver hasn't been notified yet.
This causes a panic, since the beacon interval is zero for this
interface and ath9k_cmn_beacon_config_ap() doesn't have a safety check.
Fix this panic by checking if the beacon params has been cached
for this context and use the "enable_beacon" flag maintained
locally in the driver. Also, recalculate the summary data
after the beacon params have been cached when BSS_CHANGED_BEACON_ENABLED
is received.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the current opmode is managed, the ATH_OP_BEACONS flag
needs to be set only when there is a primary station interface
and it is associated/active.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a new context is being added in addition to the current one,
then send the ASSIGN event to abort a running scan since
the addition of a context is usually followed by VIF
assignment and further operations.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Finally move the 'offchannel' instance in ath_softc
inside a CONFIG_ATH9K_CHANNEL_CONTEXT cage. The offchannel
usage in ath9k_calculate_iter_data() is closed off with
an ifdef for now, since the state/opmode calculation is
common for both the channel context mode and the normal mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath9k_vif_iter() was earlier used as an iterator
routine when calling a mac80211 utility. This is no
longer the case and hence we can mention the argument
type explicitly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
