summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath9k/hw.c
AgeCommit message (Collapse)Author
2014-01-03ath9k: Fix PHY restart workaroundSujith Manoharan
The PHY restart workaround that handles baseband hangs for packets with unsupported rates is required only for a HW bug in AR9300 v2.2. All the subsequent chips in the AR9003 family do not require this driver fix since it has been addressed in the HW. Since the value of the AR_PHY_RESTART register is written with the default initvals, make sure that PHY restart is always disabled once this particular BB hang signaure has been encountered. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-03ath9k: Add HW callbacks for MAC/BB hang checksSujith Manoharan
This is required for adding separate hang check routines for AR9002 and AR9003. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-03ath9k: Register supported HW hang checksSujith Manoharan
HW hang checks have to be done on a per-chip basis. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-03ath9k_hw: fix TSF offset calculationFelix Fietkau
Since the unit is microseconds and not milliseconds, tv_sec needs to be multiplied by 1000000, not 1000. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-03ath9k_hw: fix gentimer callback without overflow handlerFelix Fietkau
If a gentimer has both the trigger and the overflow bits set, only mask out the trigger bit if an overflow handler is present. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-19ath9k: move ath9k_debug_sync_cause out of ath9k_hwFelix Fietkau
ath9k_hw should not depend on any ath9k data structures like ath_softc Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k: Use a subroutine for the AR9330 reset WARSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k: Fix RTC reset delaySujith Manoharan
The delay that is required after issuing a RTC reset varies for each chip. Handle this properly. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k: Add a delay between RTC reset/clear for AR9003Sujith Manoharan
The small delay that is present between a RTC reset/clear operation is required for the chip to settle and this is needed for all chips, not just the AR9002 family. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: clean up station beacon timer APIFelix Fietkau
Remove unused fields, pass timer info in usec instead of TU. Preparation for fixing nexttbtt calculation Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: remove additional_swba_backoffFelix Fietkau
It is unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: simplify spur channel handlingFelix Fietkau
Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM data. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: remove ah->config.pcie_clock_reqFelix Fietkau
It is unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: remove defunct ad-hoc mode ATIM window handling codeFelix Fietkau
The hardware does not have support for ATIM processing, and the driver does not set up ah->atim_window anywhere. Additionally, the code can clobber the timer used by P2P powersave. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k_hw: clean up generic timer codeFelix Fietkau
- Use generic bitops instead of custom hackery - Move interrupt enable/disable logic from ath9k to ath9k_hw - Decouple ISR call from btcoex - Make the overflow callback optional (to prevent IRQ storms) Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-18ath9k: fix 5/10MHz channel width initialization on ar9003Lorenzo Bianconi
Move ath9k_hw_set_rfmode() after ath9k_hw_process_ini() in order to avoid AR_PHY_MODE register is overwritten with default values by ar9003_hw_process_ini() Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-09ath9k: Fix regulatory complianceSujith Manoharan
Adjusting the CCA registers for maximum permissible noise floor in ETSI/Japan domains has to be done for all AR9003 family chips. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-06Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/brcm80211/Kconfig net/mac80211/util.c
2013-12-02ath9k_hw: allow fast channel change when only CHANNEL_HT changesFelix Fietkau
The CHANNEL_HT flag is insignificant for fast channel change conditions, since it does not affect any important part of the hardware reset / channel setup. Scanning usually runs with HT disabled, so this change will slightly improve scan time on many chipsets. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-02ath9k_hw: fix TSF save/restore around chip resetFelix Fietkau
A cold reset can be triggered because of DMA stop issues, and this leads to TSF being cleared on all chipsets. To properly deal with this, always save the TSF. Additionally, account for the time it takes to do the actual chip reset, which can be quite significant. On AR9344 it takes around 4.5 ms. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-02ath9k: Remove pcieSerDesWriteSujith Manoharan
This HW config option is always set to true and is not needed. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-12-02net: wireless: ath9k: avoid possible NULL pointer dereferenceMichal Nazarewicz
Code in ath9k_hw_set_clockrate function indicates that ah->curchan (and thus chan local variable) may be NULL. If that is indeed the case, IS_CHAN_HT40(chan) check has to be performed only in branch where chan is not NULL. Moving the code under already existing if condition fixes this issue. Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-18ath9k: add noise floor parameter to ath9k_hw_getchan_noiseLorenzo Bianconi
Add nf parameter to ath9k_hw_getchan_noise() in order to compute NF for EXT chains with the same scale of noise floor calculated on CTL chains. ath9k_hw_getchan_noise() will be used in ath_process_fft() for spectral scan on HT40 channels Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: remove references to hw->confFelix Fietkau
Accessing it to get the current operating channel is racy and in the way of further channel handling related changes Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: simplify channel flagsFelix Fietkau
There was some duplication between channelFlags and chanmode, as well as a lot of redundant checks based on the combinations of flags. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: remove IS_CHAN_OFDM()Felix Fietkau
The hardware is always configured with OFDM support enabled Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: remove IS_CHAN_B()Felix Fietkau
Hardware 802.11b-only mode isn't supported by the driver (the device is configured for 802.11n/g instead). Simplify the code by removing checks for it. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-10-14ath9k_hw: remove direct accesses to channel mode flagsFelix Fietkau
Use wrappers where available. Simplifies code and helps with further improvements to the channel data structure Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26ath9k: Use bitops for calibration flagsSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26ath9k: Handle abnormal NAV in AP modeSujith Manoharan
Beacon transmission would get stuck if the NAV is an invalid value for some reason. Check and correct the NAV value in the HW when this happens. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26ath9k: replace snprintf() with scnprintf()Zefir Kurtisi
Whenever the return value of snprintf() is used to calculate remaining buffer-space, we wanted to use sncprintf() instead. Indentation is adapted where possible. Some lines exceed the line width limit, either they did it already before, or since they can not be broken reasonably well. Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-09-26ath9k: Fix regulatory compliance for AR9462/AR9565Sujith Manoharan
Adjust the CCA values based on the regulatory domain present in the EEPROM. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-28ath9k: Enable D3/L1 ASPM fix for AR9462Sujith Manoharan
AR9462 requires this HW fix for ASPM to work properly. Also, since WARegVal is used only for the AR8003 family, use AR_SREV_9300_20_OR_LATER. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-28ath9k: Remove unused ANI commandsSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-26ath9k: Fix ASPM workaround usageSujith Manoharan
The PCIE Workaround register (AR_WA/0x4004) is used to handle various hardware quirks. For AR9002 chips, AR_WA_D3_L1_DISABLE is used to prevent the HW from automatically entering L1 state when D3 is enforced. AR_WA_D3_L1_DISABLE has to be enabled for a few AR9280 based cards, mark them based on their PCI subdevice/subvendor IDs and enforce it in ar9002_hw_configpcipowersave(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-16ath9k: always use SIFS times from OFDM for 5/10 MHzSimon Wunderlich
5/10 MHz channels should always use SIFS times as defined in IEEE 802.11-2012 18.4.4 (OFDM PHY characteristics). This makes it compatible to ath5k, which does the same. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Remove "shared_chain_lnadiv"Sujith Manoharan
This variable is redundant since we can use common->bt_ant_diversity to determine if diversity has to be enabled/disabled. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-08-05ath9k: Print LNA combining mode during initSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22ath9k: Release the RF bus after setting board valuesSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22ath9k: Use correct channel when switching bandsSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22ath9k: Fix FastChannelChange for AR9462/AR9565Sujith Manoharan
Right now, even though these chips support cross-band FCC, the code is non-functional since we bail out early if the channelFlags differ. Fix this so that cross-band FCC works for cards that support this feature. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22ath9k: Add a HW flag for FCCSujith Manoharan
Fast Channel Change across 2G/5G bands is supported only by AR9462 and AR9565. Add a HW capability field to indicate this. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-07-22ath9k: make rfkill configurableJohannes Berg
When the platform doesn't have rfkill support, i.e. nothing is connected to the rfkill GPIO, there's little value in polling the GPIO. Add a Kconfig option to allow disabling the polling in ath9k. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-24ath9k: Add support for AR9462 2.1Sujith Manoharan
Various parts of the HW code are applicable for both v2.0 and v2.1. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-18ath9k: Merge HWTIMER debug level with BTCOEXSujith Manoharan
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12ath9k: Fix noisefloor calibrationSujith Manoharan
The commits, "ath9k: Fix regression in channelwidth switch at the same channel" "ath9k: Fix invalid noisefloor reading due to channel update" attempted to fix noisefloor calibration when a channel switch happens due to HT20/HT40 bandwidth change. This is causing invalid readings resulting in messages like: "ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX". This results in an incorrect noise being used initially for reporting the signal level of received packets, until NF calibration is done and the history buffer is updated via the ANI timer, which happens much later. When a bandwidth change happens, it is appropriate to reset the internal history data for the channel. Do this correctly in the reset() routine by checking the "chanmode" variable. Cc: stable@vger.kernel.org Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-12Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/ath/ath9k/Kconfig net/mac80211/iface.c
2013-06-03ath9k: Simplify ANI initializationSujith Manoharan
The check "enable_ani" is not required since it is always set to true and the logic for disabling/enabling ANI via debugfs is done at a higher layer. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-06-03ath9k: Enable WoW only for AR9462Sujith Manoharan
The only card with which WoW has been tested and verified is AR9462. Do not enable it for all cards since WoW is really quirky and needs to be tested properly with each chip. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-24ath9k_hw: improve performance for AR934x v1.3+Felix Fietkau
AR934x v1.3 no longer needs the DCU backoff reduction workaround for preventing rx overruns, but in turn needs the number of usable Tx buffers to be reduced slightly. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>