summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath10k/wmi-tlv.c
AgeCommit message (Collapse)Author
2019-02-28ath10k: Fill rx duration for each peer in fw_stats for WCN3990Surabhi Vishnoi
Currently, rx_duration for each peer is not getting populated in fw_stats debugfs entry for WCN3990. WCN3990 firmware sends rx duration for each peer as part of peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats, firmware expects host to send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD. Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer in fw_stats debugfs entry. Currently the driver handles 32-bit rx_duration, but the rx_duration for WCN3990 can be upto 63 bit. The firmware sends rx_duration split into two 32-bit fields, with the upper 32-bits being valid only if its MSB is set. This change handles the 63-bit rx_duration obtained from WCN3990 and maintain the backward compatibility. To get the rx_duration of each connected peer : cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: Fix length of wmi tlv command for protected mgmt framesSurabhi Vishnoi
The length of wmi tlv command for management tx send is calculated incorrectly in case of protected management frames as there is addition of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of firmware as the wmi tlv mgmt tx send command for protected mgmt frames is formed wrongly. Fix the length calculation of wmi tlv command for mgmt tx send in case of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only once. Tested HW: WCN3990 Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Fixes: 1807da49733e "ath10k: wmi: add management tx by reference support over wmi" Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: correct the format of host memory chunks in wmi init commandYu Wang
This is a theoretical fix, the issue is found in code review. When adding the host memory chunks into wmi-tlv init command, there is no separate tlv header for each host memory chunk in the struct array, which breaches the convention between host and firmware, will result in mismatch between the two. To fix this issue, add separate tlv headers for the host memory chunks in wmi-tlv init command. Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: enhance logging for vdev pdev & peer set paramRakesh Pillai
Currently after enabling the WMI debug logging, there is no detail printed about the param id and the param value for the pdev, vdev and peer params which are set. Enhance the WMI logging to print the param id and the param value for pdev, vdev and peer set param wmi commands. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1 WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-26ath10k: add support for ack rssi value of management tx packetsAbhishek Ambure
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that the firmware has the capability to send the RSSI value of the ACK for all data and management packets transmitted. If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware sends RSSI value in "management" tx completion event. Host extracts ack rssi values of management packets from their tx completion event. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-20ath10k: switch to use SPDX license identifiersKalle Valo
Use SPDX identifiers everywhere in ath10k. Makefile was incorrectly marked in commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license"), fix that as well. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-11ath10k: disable interface pause wow config for integrated chipsetGovind Singh
wow pause iface config controls the PCI D0/D3-WOW cases for pcie bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config for bus/link that cannot be suspended ex:snoc and does not trigger common subsystem shutdown. Disable interface pause wow config for integrated chipset(WCN3990) for correct WOW configuration in the firmware. Testing: Tested on WCN3990 HW. Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1. Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-11ath10k: update GCMP & GCMP-256 cipher suite number for WCN3990Abhishek Ambure
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value set to 9 while non-TLV firmware expects key cipher value set to 8 for enabling GCMP and GCMP-256 cipher suites. To fix this problem, attach the key cipher suite values based on wmi version. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Abhishek Ambure <aambure@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-07ath10k: reduce transmit msdu countAlagu Sankar
Reduce the transmit MSDU count for SDIO, to match with the descriptors as used by the firmware. This also acts as a high watermark level for transmit. Too many packets to the firmware results in transmit overflow interrupt. It only affect SDIO chip, it will not cause functionaly changes to other hardware. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1. Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-07ath10k: Enable bundle tx compl for management frames in WCN3990Rakesh Pillai
WCN3990 sends tx completion of multiple management frames bundled together in a single event, if the host driver exposes the support to handle this bundled tx completion event. This reduces the number of WMI events which are sent to the host driver by the target. Set the BUNDLE_TX_COMPL flag in the host capability flags when host sends the wmi init command, to indicate the host capability to handle bundled tx completion for management frames. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-02-07ath10k: Handle bundled tx completion for management framesRakesh Pillai
WCN3990 supports sending tx completion for multiple management frames bundled together in a single event. Add support to handle the bundled tx completion event for WCN3990. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-12-20ath10k: move non-fatal warn logs to dbg levelGovind Singh
During driver load below warn logs are printed in the console. Since driver may not implement all wmi events sent by fw and all of them are non-fatal, move this log to debug level to remove un-necessary warn message on console. [ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393 [ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-11-05ath10k: remove set but not used variable 'tlv_len'YueHaibing
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/ath10k/wmi-tlv.c: In function 'ath10k_wmi_tlv_op_gen_config_pno_start': drivers/net/wireless/ath/ath10k/wmi-tlv.c:3455:6: warning: variable 'tlv_len' set but not used [-Wunused-but-set-variable] It never used since inroduction in commit ce834e280f2f ("ath10k: support NET_DETECT WoWLAN feature") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-11-05ath10k: fill the channel survey results for WCN3990 correctlyRakesh Pillai
The host driver currently expects the channel info event to be received in pairs for all the channels, i.e. the first chan_info event for a particular channel will not have the COMPLETE flag set and the second chan_info event for the same channel will have the COMPLETE flag set. The HL2.0 firmware sends only one channel info event per channel which is scanned without the COMPLETE flag set. After sending the chan_info_event for all the channels, the HL2.0 firmware sends a chan_info_event with COMPLETE flag set to indicate the completion of the channel info event. The firmware does not indicate this behavior with any service bitmap and hence a new firmware feature flag is used to handle the modified parsing of the channel info events, in the host driver, for the firmware which sends single channel info event per scanned channel. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-10-13ath10k: support NET_DETECT WoWLAN featureWen Gong
For WoWLAN support it is expected to support wake up based on discovery of one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature, which shows up as an NL80211 feature flag. This shows up in 'iw phy' as: WoWLAN support: * wake up on network detection, up to 16 match sets And it can be enabled with command: iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo Firmware will do scan by the configured parameters after suspend and wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> [kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-10-01ath10k: remove duplicated includesYueHaibing
remove duplicated include from ath10k driver. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-10-01ath10k: add default value for num_peers in WMI TLV initErik Stromdahl
The hw_params value will only be used if it was explicitly set in the global hw_params array. This makes it possible to have the num_peers member unset. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-09-06ath10k: use hw_params.num_peers for num_tids in TLV initErik Stromdahl
As TARGET_TLV_NUM_TIDS is calculated like this: #define TARGET_TLV_NUM_TIDS ((TARGET_TLV_NUM_PEERS) * 2) ... it is better to use the per device hw_params.num_peers value in the TLV init message (if set), rather than using a hard coded value. This makes the value used in the TLV init message match the hw_param value. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-30ath10k: remove redundant pointers 'dev' and 'noa'Colin Ian King
Pointers dev and noa are being assigned but are never used hence they are redundant and can be removed. Cleans up clang warnings: warning: variable 'dev' set but not used [-Wunused-but-set-variable] warning: variable 'noa' set but not used [-Wunused-but-set-variable] Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-30ath10k: handle mgmt tx completion eventRakesh Pillai
WCN3990 transmits management frames via WMI with reference. Currently, with the management tx completion not being handled, these frames are not getting freed even after the transmission status is returned by the firmware. The transmitted management frames should be freed when the firmware sends the over-the-air tx status of the corresponding management frames. Handle the wmi mgmt tx completion event and free the corresponding management frame. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-30ath10k: disable bundle mgmt tx completion event supportSurabhi Vishnoi
The tx completion of multiple mgmt frames can be bundled in a single event and sent by the firmware to host, if this capability is not disabled explicitly by the host. If the host cannot handle the bundled mgmt tx completion, this capability support needs to be disabled in the wmi init cmd, sent to the firmware. Add the host capability indication flag in the wmi ready command, to let firmware know the features supported by the host driver. This field is ignored if it is not supported by firmware. Set the host capability indication flag(i.e. host_capab) to zero, for disabling the support of bundle mgmt tx completion. This will indicate the firmware to send completion event for every mgmt tx completion, instead of bundling them together and sending in a single event. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org> Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-07-30ath10k: fix open brace location in ath10k_wmi_tlv_op_gen_dbglog_cfg()Kalle Valo
Fixes a recently added checkpatch warning: wmi-tlv.c:2703: open brace '{' following function definitions go on the next line Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-28ath10k: fix tlv 5ghz channel missing issueZhi Chen
The 5ghz channel parameters of TLV target wasn't passed to host, it caused host can only use lower channels from 36 to 64. Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-28ath10k: fix scan crash due to incorrect length calculationZhi Chen
Length of WMI scan message was not calculated correctly. The allocated buffer was smaller than what we expected. So WMI message corrupted skb_info, which is at the end of skb->data. This fix takes TLV header into account even if the element is zero-length. Crash log: [49.629986] Unhandled kernel unaligned access[#1]: [49.634932] CPU: 0 PID: 1176 Comm: logd Not tainted 4.4.60 #180 [49.641040] task: 83051460 ti: 8329c000 task.ti: 8329c000 [49.646608] $ 0 : 00000000 00000001 80984a80 00000000 [49.652038] $ 4 : 45259e89 8046d484 8046df30 8024ba70 [49.657468] $ 8 : 00000000 804cc4c0 00000001 20306320 [49.662898] $12 : 33322037 000110f2 00000000 31203930 [49.668327] $16 : 82792b40 80984a80 00000001 804207fc [49.673757] $20 : 00000000 0000012c 00000040 80470000 [49.679186] $24 : 00000000 8024af7c [49.684617] $28 : 8329c000 8329db88 00000001 802c58d0 [49.690046] Hi : 00000000 [49.693022] Lo : 453c0000 [49.696013] epc : 800efae4 put_page+0x0/0x58 [49.700615] ra : 802c58d0 skb_release_data+0x148/0x1d4 [49.706184] Status: 1000fc03 KERNEL EXL IE [49.710531] Cause : 00800010 (ExcCode 04) [49.714669] BadVA : 45259e89 [49.717644] PrId : 00019374 (MIPS 24Kc) Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-05-12ath10k: add quiet mode support for QCA6174/QCA9377Yu Wang
To enable thermal throttling for QCA6174 and QCA9377, implement gen_pdev_set_quiet_mode for them. With this change, quiet period for QCA6174/QCA9377 can be also set/get via debugfs. Usage: To set quiet period: echo <period> > /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period To get the current quiet period: cat /sys/kernel/debug/ieee80211/phyX/ath10k/quiet_period This change has been verified with QCA6174 hw3.2(fw: WLAN_RM.4.4.1-00102-QCARMSWP-1). Signed-off-by: Yu Wang <yyuwang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: support MAC address randomization in scanCarl Huang
The ath10k reports the random_mac_addr capability to upper layer based on the service bit firmware reported. Driver sets the spoofed flag in scan_ctrl_flag to firmware if upper layer has enabled this feature in scan request. Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1, but QCA9377 is also affected. Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-04-24ath10k: add WMI_SERVICE_AVAILABLE_EVENT supportCarl Huang
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT, the 128bit service map in WMI_SERVICE_READY_EVENT is not enough for firmware to notice new WLAN service to host driver. Hereby, for thoese new WLAN service, firmware will notice host driver by WMI_SERVICE_AVAILABLE_EVENT. Signed-off-by: Alan Liu <alanliu@codeaurora.org> Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-29ath10k: enable TDLS peer inactivity detectionYingying Tang
Enable TDLS peer inactivity detetion feature. QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting. Set related parameters in TDLS WMI command to enable this feature. Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-29ath10k: enable TDLS peer buffer STA featureYingying Tang
Enable TDLS peer buffer STA feature. QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA, it reports this capability through wmi service map in wmi service ready event. Set related parameter in TDLS WMI command to enable this feature. Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-29ath10k: enable QCA6174/QCA9377 to read the chip temperatureRyan Hsu
The firmware of QCA6174/QCA9377 already support the feature, just enable it to be able to handle the get_temperature command and process the event. You can read the temperature by using the hwmon interface, cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input Verified with the following hardware and software combination, QCA6174, only firmware-4.bin doesn't support this, otherwise all support. QCA9377, all the firmwares upstreamed support this command Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-03-14ath10k: dma unmap mgmt tx buffer if wmi cmd send failsRakesh Pillai
WCN3990 sends mgmt frames by reference via WMI. The host dma maps the mgmt frame and sends the physical address to the firmware in the wmi command. Since the dma mapping is done in the gen_mgmt_tx and if the wmi command send fails, the corresponding mgmt frame is not being dma unmapped. Fix the missing dma unmapping of mgmt tx frame when wmi command sending fails for mgmt tx by reference via WMI. The already exisiting mgmt tx using copy by value does not need such dma unmapping. Add a separate wmi-tlv op for mgmt tx via ref, which takes care of unmapping the dma address, in case of wmi command sending failure. Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2017-12-27ath10k: update copyright yearKalle Valo
Update year for Qualcomm Atheros, Inc. copyrights. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-27ath10k: wmi: remove redundant integer fcColin Ian King
Variable fc is being assigned but never used, so remove it. Cleans up the clang warning: warning: Value stored to 'fc' is never read Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-14ath10k: wmi: get wmi init parameter values from hw paramsRakesh Pillai
The parameter values for skid limit, number of peers and wds entries values which are sent in wmi init cmd are hardware specific. Add support to obtain skid limit, number of peers and wds entries values from hw params which will have the hw specific values for these parameters. Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-14ath10k: wmi: add management tx by reference support over wmiRakesh Pillai
HL1.0 firmware branch, used in wcn3990, transmits management frames by reference over WMI. Add support for management tx by reference over WMI. Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-12-14ath10k: wmi: modify svc bitmap parsing for wcn3990Rakesh Pillai
Due to the limitation of wmi tlv parsing logic, if there are two parameters in a wmi event with same tlv tag, we can get only the last value, as it overwrites the prev value of the same tlv tag. The service ready event in wcn3990 contains two parameters of the same tag UINT32, due to which the svc bitmap is overwritten with the DBS support parameter. Refactor the service ready event parsing to allow parsing two tlv of the same tag UINT32 for wcn3990. Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Govind Singh <govinds@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-06-28ath10k: fix a bunch of spelling mistakes in messagesColin Ian King
Fix the following spelling mistakes in messages: syncronise -> synchronize unusally -> unusually addrress -> address inverval -> interval Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2017-01-13ath10k: add VHT160 supportSebastian Gottschall
This patch adds full VHT160 support for QCA9984 chipsets Tested on Netgear R7800. 80+80 is possible, but disabled so far since it seems to contain glitches like missing vht station flags (this may be firmware or mac80211 related). Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com> [kvalo@qca.qualcomm.com: refactoring and fix few warnings] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-12-30ath10k: fix potential memory leak in ath10k_wmi_tlv_op_pull_fw_stats()Christian Lamparter
ath10k_wmi_tlv_op_pull_fw_stats() uses tb = ath10k_wmi_tlv_parse_alloc(...) function, which allocates memory. If any of the three error-paths are taken, this tb needs to be freed. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-12-01ath10k: fix TLV set regdomain commandErik Stromdahl
There is a typo bug in the current implementation of ath10k_wmi_tlv_op_gen_pdev_set_rd. The conformance test limits are not set up properly. The two arguments ctl2g and ctl5g were not used at all. Instead, the regdomain arguments rd2g and rd5g were used for the ctl settings as well. Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-11-23ath10k: add spectral scan support to wmi-tlvMichal Kazior
Command structure and event flow doesn't seem to be any different compared to existing implementation for other firmware branches. This patch effectively adds in-driver support for spectral scanning on QCA61x4 and QCA9377. Tested QCA9377 w/ WLAN.TF.1.0-00267-1. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-11-23ath10k: remove set/get_tsf ieee80211_opsPedersen, Thomas
Neither of these did the right thing: - get_tsf just returned 0 - set_tsf assumed a simple offset was applied against get_tsf(), which works, except in the case of calculating TSF from rx_mactime (actual TSF). Just remove them for now. We can reimplement set_tsf in terms of TSF increment/decrement in the future if get_tsf is ever supported by FW. Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-09-02ath10k: Added support for extended dbglog module id for 10.4Maharaja Kennadyrajan
For 10.4 fw versions, dbglog module id has been extended from u32 to u64, hence this patch fixes the same in the ath10k driver side. This patch doesn't break the older 10.4 releases. The FW change is already present in the older FWs. Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-08-31ath10k: implement wmi echo eventMichal Kazior
Will be useful for implementing command barriers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-08-31ath10k: implement wmi echo commandMichal Kazior
Will be useful for implementing command barriers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-04-12ath10k: add a support of set_tsf on vdev interfacePeter Oh
10.2.4.70.24 firmware introduces new feature to set TSF via vdev parameter, hence implement relevant function. set_tsf function can be used to shift TBTT that will help avoid its clockdrift which happens when beacons are collided. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2016-02-02ath10k: add abstraction layer for vdev subtypePeter Oh
Abstraction layer for vdev subtype is added to solve subtype mismatch and to give flexible compatibility among different firmware revisions. For instance, 10.2 and 10.4 firmware has different definition of their vdev subtypes for Mesh. 10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5. Hence use the abstraction API to get right subtype to use. Signed-off-by: Peter Oh <poh@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-11-04ath10k: add abstraction layer for peer flagsTamizh chelvam
Abstraction layer for peer flags is added to fix ABI breakage. Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2015-10-29ath10k: add FW API support to test modeAlan Liu
Add WMI-TLV and FW API support in ath10k testmode. Ath10k can get right wmi command format from UTF image to communicate UTF firmware. Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 08:31:47 +0000