| Age | Commit message (Collapse) | Author |
|---|
|
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
WMI ops wrappers did not properly check for null
function pointers for spectral scan. This caused
null dereference crash with WMI-TLV based firmware
which doesn't implement spectral scan.
The crash could be triggered with:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
The crash looked like this:
[ 168.031989] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 168.037406] IP: [< (null)>] (null)
[ 168.040395] PGD cdd4067 PUD fa0f067 PMD 0
[ 168.043303] Oops: 0010 [#1] SMP
[ 168.045377] Modules linked in: ath10k_pci(O) ath10k_core(O) ath mac80211 cfg80211 [last unloaded: cfg80211]
[ 168.051560] CPU: 1 PID: 1380 Comm: bash Tainted: G W O 4.8.0 #78
[ 168.054336] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 168.059183] task: ffff88000c460c00 task.stack: ffff88000d4bc000
[ 168.061736] RIP: 0010:[<0000000000000000>] [< (null)>] (null)
...
[ 168.100620] Call Trace:
[ 168.101910] [<ffffffffa03b9566>] ? ath10k_spectral_scan_config+0x96/0x200 [ath10k_core]
[ 168.104871] [<ffffffff811386e2>] ? filemap_fault+0xb2/0x4a0
[ 168.106696] [<ffffffffa03b97e6>] write_file_spec_scan_ctl+0x116/0x280 [ath10k_core]
[ 168.109618] [<ffffffff812da3a1>] full_proxy_write+0x51/0x80
[ 168.111443] [<ffffffff811957b8>] __vfs_write+0x28/0x120
[ 168.113090] [<ffffffff812f1a2d>] ? security_file_permission+0x3d/0xc0
[ 168.114932] [<ffffffff8109b912>] ? percpu_down_read+0x12/0x60
[ 168.116680] [<ffffffff811965f8>] vfs_write+0xb8/0x1a0
[ 168.118293] [<ffffffff81197966>] SyS_write+0x46/0xa0
[ 168.119912] [<ffffffff818f2972>] entry_SYSCALL_64_fastpath+0x1a/0xa4
[ 168.121737] Code: Bad RIP value.
[ 168.123318] RIP [< (null)>] (null)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
For 10.4 fw versions, dbglog module id has been extended from u32
to u64, hence this patch fixes the same in the ath10k driver side.
This patch doesn't break the older 10.4 releases. The FW change
is already present in the older FWs.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Will be useful for implementing command barriers.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI ops to send pdev_bss_chan_info_request command to target.
This command will be used to retrieve updated cycle counters and noise
floor value of current operating channel (bss channel).
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add API support for Extended Resource Configuration for 10.4. This
is useful to enable new features like Peer Stats, LTEU etc if the
firmware advertises support for the service. This is also done to
provide backward compatibility with older firmware. Also for clarity
send default host platform type as 'WMI_HOST_PLATFORM_HIGH_PERF',
though this should not make any difference in functionality
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Abstraction layer for vdev subtype is added to solve
subtype mismatch and to give flexible compatibility
among different firmware revisions.
For instance, 10.2 and 10.4 firmware has different
definition of their vdev subtypes for Mesh.
10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5.
Hence use the abstraction API to get right subtype to use.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The patch makes debug stats prints fw specific by adding a new member
in wmi_ops. That way it's easier to add fw_stats support to 10.4 firmware.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh Chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The Transmit Power Control (TPC) dump will show the power control values for
each rate which makes it easier to debug calibration problems.
Example usage:
# cat /sys/kernel/debug/ieee80211/phy0/ath10k/tpc_stats
TPC config for channel 5180 mode 10
CTL = 0x10 Reg. Domain = 58
Antenna Gain = 1 Reg. Max Antenna Gain = 0
Power Limit = 34 Reg. Max Power = 34
Num tx chains = 3 Num supported rates = 155
**********CDD POWER TABLE*******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
1 CCk 0x41 0 0 0
[...]
154 HTCUP 0x 0 24 0 0
**********STBC POWER TABLE******
No. Preamble Rate_code tpc_valu1 tpc_value2 tpc_value3
0 CCK 0x40 0 0 0
[...]
154 HTCUP 0x 0 24 24 0
**********TXBF POWER TABLE******
is used to dump the tx power control stats.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
As a part of tdls implementation introduce
tdls related wmi data structures, constant
values and functions.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for WOW patterns.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for WOW like enable,
wakeup events and host wakeup indication.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This can be used to implement offloaded rssi
threshold, beacon miss or even automatic
in-firmware BSS roaming in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The expected parameter is not a single value but a
mask of values.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Introduce an optional log level configuration for the existing debugfs fw_dbglog file. It
allows users to configure the desired log level for firmware dbglog messages.
To configure log level as WARN:
echo 0xffffffff 2 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
The values are:
VERBOSE 0
INFO 1
WARN 2
ERR 3
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The command logic shouldn't really care about
arvif structure.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 has STA keepalive
service available. The service can provide
automatic idle connection polling via NullFunc
frames to AP when acting as a client.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 supports this.
This will be used soon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
mac80211 already requests WMM per vif but firmware
wasn't able to handle this until now. However new
wmi-tlv firmware for qca6174 is capable of this.
This prepares per-vif WMM param setup.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.
This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI command support for reading temperature from the target and
corresponding WMI temperature event handler. The pdev_get_temperature
command is currently supported in 10.2 firmware alone.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add WMI support to send pdev_set_quiet_mode command to target.
This will be used for thermal mitigation purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.
The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
