| Age | Commit message (Collapse) | Author |
|---|
|
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.
This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Lots of bugfixes as usual but also some new features.
Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
rt2x00
* add support MT7620
mwifiex
* enable auto deep sleep mode for USB chipsets
brcmfmac
* add support for network namespaces (WIPHY_FLAG_NETNS_OK)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the 'commit ebee76f7fa46 ("ath10k: allow setting coverage class")',
it inherits the design and the address offset from ath9k, but the address
is not applicable to QCA6174, which leads to a random crash while doing the
resume() operation, since the set_coverage_class.ops will be called from
ieee80211_reconfig() when resume() (if the wow is not configured).
Fix the incorrect address offset here to avoid the random crash.
Verified on QCA6174/hw3.0 with firmware WLAN.RM.4.4-00022-QCARMSWPZ-2.
kvalo: this also seems to fix a regression with firmware restart.
Fixes: ebee76f7fa46 ("ath10k: allow setting coverage class")
Cc: <stable@vger.kernel.org> # v4.10
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
There are slight differences in Rx hw descriptor information
among different chips. So far driver does not use those new
information for any functionalities, but there is one important
information which is available from QCA99X0 onwards to indicate
the number of bytes that hw padded at the begining of the rx
payload and this information is needed to undecap the rx
packet. Add an abstraction for Rx desc to make use of the
new desc information available. The callback that this patch
defines to retrieve the padding bytes will be used in follow-up
patch.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[Rename operations to hw_ops for other purposes]
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a98 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In QCA4019, cycle counter wraparound is not tied to rx
clear counter. Each counter would wraparound individually
and after wraparound the respective counter will be reset
to 0x7fffffff while other counter still running unaffected.
Define a new wraparound type for this behaviour and handle
it separately so that rx clear counter wraparound is also
handled just like cycle counter. With this type of
wraparound we can accurately compute and report channel
active/busy time when any of the counter overflows.
Fixes: ee9ca147c59 ("ath10k: Fix survey reporting with QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
New register table is added for qca4019 to tell about it's
register mapping details.
Nothing much other than this.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
commit a521ee983d312db7 ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.
User experience was a failing boot up sequence (crashing device during
initialization):
[ 181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[ 181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[ 181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[ 181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[ 181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[ 181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70
Fix it by updating the address with correct value.
Fixes: a521ee983d31 ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Add more register address and mask which can be different
for newer chip to hw_reg table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This is to prepare ath10k to support newer chip set.
Values like CE_COUNT, MSI_ASSIGN_CE_MAX and
RTC_STATE_V_ON can be different for different
chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.
This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
