summaryrefslogtreecommitdiff
path: root/drivers/net/phy
AgeCommit message (Collapse)Author
2024-09-18net: phy: vitesse: repair vsc73xx autonegotiationPawel Dembicki
[ Upstream commit de7a670f8defe4ed2115552ad23dea0f432f7be4 ] When the vsc73xx mdio bus work properly, the generic autonegotiation configuration works well. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-09-12net: phy: Fix missing of_node_put() for ledsJinjie Ruan
[ Upstream commit 2560db6ede1aaf162a73b2df43e0b6c5ed8819f7 ] The call of of_get_child_by_name() will cause refcount incremented for leds, if it succeeds, it should call of_node_put() to decrease it, fix it. Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs") Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240830022025.610844-1-ruanjinjie@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-11net: phy: micrel: Fix the KSZ9131 MDI-X status issueRaju Lakkaraju
[ Upstream commit 84383b5ef4cd21b4a67de92afdc05a03b5247db9 ] The MDIX status is not accurately reflecting the current state after the link partner has manually altered its MDIX configuration while operating in forced mode. Access information about Auto mdix completion and pair selection from the KSZ9131's Auto/MDI/MDI-X status register Fixes: b64e6a8794d9 ("net: phy: micrel: Add PHY Auto/MDI/MDI-X set driver for KSZ9131") Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20240725071125.13960-1-Raju.Lakkaraju@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-08-11net: phy: realtek: add support for RTL8366S Gigabit PHYMark Mentovai
[ Upstream commit 225990c487c1023e7b3aa89beb6a68011fbc0461 ] The PHY built in to the Realtek RTL8366S switch controller was previously supported by genphy_driver. This PHY does not implement MMD operations. Since commit 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()"), MMD register reads have been made during phy_probe to determine EEE support. For genphy_driver, these reads are transformed into 802.3 annex 22D clause 45-over-clause 22 mmd_phy_indirect operations that perform MII register writes to MII_MMD_CTRL and MII_MMD_DATA. This overwrites those two MII registers, which on this PHY are reserved and have another function, rendering the PHY unusable while so configured. Proper support for this PHY is restored by providing a phy_driver that declares MMD operations as unsupported by using the helper functions provided for that purpose, while remaining otherwise identical to genphy_driver. Fixes: 9b01c885be36 ("net: phy: c22: migrate to genphy_c45_write_eee_adv()") Reported-by: Russell Senior <russell@personaltelco.net> Closes: https://github.com/openwrt/openwrt/issues/15981 Link: https://github.com/openwrt/openwrt/issues/15739 Signed-off-by: Mark Mentovai <mark@mentovai.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-07-18net: phy: microchip: lan87xx: reinit PHY after cable testOleksij Rempel
[ Upstream commit 30f747b8d53bc73555f268d0f48f56174fa5bf10 ] Reinit PHY after cable test, otherwise link can't be established on tested port. This issue is reproducible on LAN9372 switches with integrated 100BaseT1 PHYs. Fixes: 788050256c411 ("net: phy: microchip_t1: add cable test support for lan87xx phy") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://patch.msgid.link/20240705084954.83048-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-07-05net: phy: micrel: add Microchip KSZ 9477 to the device tableEnguerrand de Ribaucourt
[ Upstream commit 54a4e5c16382e871c01dd82b47e930fdce30406b ] PHY_ID_KSZ9477 was supported but not added to the device table passed to MODULE_DEVICE_TABLE. Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support") Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-27net: phy: mxl-gpy: Remove interrupt mask clearing from config_initRaju Lakkaraju
[ Upstream commit c44d3ffd85db03ebcc3090e55589e10d5af9f3a9 ] When the system resumes from sleep, the phy_init_hw() function invokes config_init(), which clears all interrupt masks and causes wake events to be lost in subsequent wake sequences. Remove interrupt mask clearing from config_init() and preserve relevant masks in config_intr(). Fixes: 7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-27net: sfp: add quirk for ATS SFP-GE-T 1000Base-TX moduleDaniel Golle
[ Upstream commit 0805d67bc0ef95411228e802f31975cfb7555056 ] Add quirk for ATS SFP-GE-T 1000Base-TX module. This copper module comes with broken TX_FAULT indicator which must be ignored for it to work. Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [ rebased on top of net-next ] Signed-off-by: Marek Behún <kabel@kernel.org> Link: https://lore.kernel.org/r/20240423090025.29231-1-kabel@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-21net: sfp: Always call `sfp_sm_mod_remove()` on removeCsókás, Bence
[ Upstream commit e96b2933152fd87b6a41765b2f58b158fde855b6 ] If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will not be run. As a consequence, `sfp_hwmon_remove()` is not getting run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()` itself checks `sfp->sm_mod_state` anyways, so this check was not really needed in the first place. Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine") Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-21net: phy: Micrel KSZ8061: fix errata solution not taking effect problemTristram Ha
[ Upstream commit 0a8d3f2e3e8d8aea8af017e14227b91d5989b696 ] KSZ8061 needs to write to a MMD register at driver initialization to fix an errata. This worked in 5.0 kernel but not in newer kernels. The issue is the main phylib code no longer resets PHY at the very beginning. Calling phy resuming code later will reset the chip if it is already powered down at the beginning. This wipes out the MMD register write. Solution is to implement a phy resume function for KSZ8061 to take care of this problem. Fixes: 232ba3a51cc2 ("net: phy: Micrel KSZ8061: link failure after cable connect") Signed-off-by: Tristram Ha <tristram.ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-21net: phy: micrel: fix KSZ9477 PHY issues after suspend/resumeTristram Ha
[ Upstream commit 6149db4997f582e958da675092f21c666e3b67b7 ] When the PHY is powered up after powered down most of the registers are reset, so the PHY setup code needs to be done again. In addition the interrupt register will need to be setup again so that link status indication works again. Fixes: 26dd2974c5b5 ("net: phy: micrel: Move KSZ9477 errata fixes to PHY driver") Signed-off-by: Tristram Ha <tristram.ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-16net: sfp-bus: fix SFP mode detect from bitrateRussell King (Oracle)
commit 97eb5d51b4a584a60e5d096bdb6b33edc9f50d8d upstream. The referenced commit moved the setting of the Autoneg and pause bits early in sfp_parse_support(). However, we check whether the modes are empty before using the bitrate to set some modes. Setting these bits so early causes that test to always be false, preventing this working, and thus some modules that used to work no longer do. Move them just before the call to the quirk. Fixes: 8110633db49d ("net: sfp-bus: allow SFP quirks to override Autoneg and pause bits") Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://lore.kernel.org/r/E1rPMJW-001Ahf-L0@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-06-12net: micrel: Fix lan8841_config_intr after getting out of sleep modeHoratiu Vultur
[ Upstream commit 4fb679040d9f758eeb3b4d01bbde6405bf20e64e ] When the interrupt is enabled, the function lan8841_config_intr tries to clear any pending interrupts by reading the interrupt status, then checks the return value for errors and then continue to enable the interrupt. It has been seen that once the system gets out of sleep mode, the interrupt status has the value 0x400 meaning that the PHY detected that the link was in low power. That is correct value but the problem is that the check is wrong. We try to check for errors but we return an error also in this case which is not an error. Therefore fix this by returning only when there is an error. Fixes: a8f1a19d27ef ("net: micrel: Add support for lan8841 PHY") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240524085350.359812-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-12net: phy: micrel: set soft_reset callback to genphy_soft_reset for KSZ8061Mathieu Othacehe
[ Upstream commit 128d54fbcb14b8717ecf596d3dbded327b9980b3 ] Following a similar reinstate for the KSZ8081 and KSZ9031. Older kernels would use the genphy_soft_reset if the PHY did not implement a .soft_reset. The KSZ8061 errata described here: https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8061-Errata-DS80000688B.pdf and worked around with 232ba3a51c ("net: phy: Micrel KSZ8061: link failure after cable connect") is back again without this soft reset. Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Tested-by: Karim Ben Houcine <karim.benhoucine@landisgyr.com> Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-06-12net: micrel: Fix receiving the timestamp in the frame for lan8841Horatiu Vultur
[ Upstream commit aea27a92a41dae14843f92c79e9e42d8f570105c ] The blamed commit started to use the ptp workqueue to get the second part of the timestamp. And when the port was set down, then this workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING is not enabled, then the ptp_clock is not initialized so then it would crash when it would try to access the delayed work. So then basically by setting up and then down the port, it would crash. The fix consists in checking if the ptp_clock is initialized and only then cancel the delayed work. Fixes: cc7554954848 ("net: micrel: Change to receive timestamp in the frame for lan8841") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-05-02net: phy: dp83869: Fix MII mode failureMD Danish Anwar
[ Upstream commit 6c9cd59dbcb09a2122b5ce0dfc07c74e6fc00dc0 ] The DP83869 driver sets the MII bit (needed for PHY to work in MII mode) only if the op-mode is either DP83869_100M_MEDIA_CONVERT or DP83869_RGMII_100_BASE. Some drivers i.e. ICSSG support MII mode with op-mode as DP83869_RGMII_COPPER_ETHERNET for which the MII bit is not set in dp83869 driver. As a result MII mode on ICSSG doesn't work and below log is seen. TI DP83869 300b2400.mdio:0f: selected op-mode is not valid with MII mode icssg-prueth icssg1-eth: couldn't connect to phy ethernet-phy@0 icssg-prueth icssg1-eth: can't phy connect port MII0 Fix this by setting MII bit for DP83869_RGMII_COPPER_ETHERNET op-mode as well. Fixes: 94e86ef1b801 ("net: phy: dp83869: support mii mode when rgmii strap cfg is used") Signed-off-by: MD Danish Anwar <danishanwar@ti.com> Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-05-02net: phy: mediatek-ge-soc: follow netdev LED trigger semanticsDaniel Golle
[ Upstream commit 5b5f724b05c550e10693a53a81cadca901aefd16 ] Only blink if the link is up on a LED which is programmed to also indicate link-status. Otherwise, if both LEDs are in use to indicate different speeds, the resulting blinking being inverted on LEDs which aren't switched on at a specific speed is quite counter-intuitive. Also make sure that state left behind by reset or the bootloader is recognized correctly including the half-duplex and full-duplex bits as well as the (unsupported by Linux netdev trigger semantics) link-down bit. Fixes: c66937b0f8db ("net: phy: mediatek-ge-soc: support PHY LEDs") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-04-13net: phy: phy_device: Prevent nullptr exceptions on ISRAndre Werner
[ Upstream commit 61c81872815f46006982bb80460c0c80a949b35b ] If phydev->irq is set unconditionally, check for valid interrupt handler or fall back to polling mode to prevent nullptr exceptions in interrupt service routine. Signed-off-by: Andre Werner <andre.werner@systec-electronic.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240129135734.18975-2-andre.werner@systec-electronic.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-04-10net: phy: micrel: Fix potential null pointer dereferenceAleksandr Mishin
commit 96c155943a703f0655c0c4cab540f67055960e91 upstream. In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may return NULL as ptp_header due to abnormal packet type or corrupted packet. Fix this bug by adding ptp_header check. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-04-10net: phy: micrel: lan8814: Fix when enabling/disabling 1-step timestampingHoratiu Vultur
commit de99e1ea3a35f23ff83a31d6b08f43d27b2c6345 upstream. There are 2 issues with the blamed commit. 1. When the phy is initialized, it would enable the disabled of UDPv4 checksums. The UDPv6 checksum is already enabled by default. So when 1-step is configured then it would clear these flags. 2. After the 1-step is configured, then if 2-step is configured then the 1-step would be still configured because it is not clearing the flag. So the sync frames will still have origin timestamps set. Fix this by reading first the value of the register and then just change bit 12 as this one determines if the timestamp needs to be inserted in the frame, without changing any other bits. Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-03-26net: phy: fix phy_read_poll_timeout argument type in genphy_loopbackNikita Kiryushin
[ Upstream commit 32fa4366cc4da1c97b725a0066adf43c6b298f37 ] read_poll_timeout inside phy_read_poll_timeout can set val negative in some cases (for example, __mdiobus_read inside phy_read can return -EOPNOTSUPP). Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()") should fix problems with wrong-signed vals, but I do not see how as val is sent to phy_read as is and __val = phy_read (not val) is checked for sign. Change val type for signed to allow better error handling as done in other phy_read_poll_timeout callers. This will not fix any error handling by itself, but allows, for example, to modify cond with appropriate sign check or check resulting val separately. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-26net: phy: dp83822: Fix RGMII TX delay configurationTim Pambor
[ Upstream commit c8a5c731fd1223090af57da33838c671a7fc6a78 ] The logic for enabling the TX clock shift is inverse of enabling the RX clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is set. Correct the current behavior and always write the delay configuration to ensure consistent delay settings regardless of bootloader configuration. Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69 Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay") Signed-off-by: Tim Pambor <tp@osasysteme.de> Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-26net: phy: fix phy_get_internal_delay accessing an empty arrayKévin L'hôpital
[ Upstream commit 4469c0c5b14a0919f5965c7ceac96b523eb57b79 ] The phy_get_internal_delay function could try to access to an empty array in the case that the driver is calling phy_get_internal_delay without defining delay_values and rx-internal-delay-ps or tx-internal-delay-ps is defined to 0 in the device-tree. This will lead to "unable to handle kernel NULL pointer dereference at virtual address 0". To avoid this kernel oops, the test should be delay >= 0. As there is already delay < 0 test just before, the test could only be size == 0. Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay") Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com> Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-01net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHYSiddharth Vadapalli
[ Upstream commit 3489182b11d35f1944c1245fc9c4867cf622c50f ] Commit bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY. While that commit indicated that the RTL8211F_PHYCR2 register is not supported by the "VD-CG" PHY model and therefore updated the corresponding section in rtl8211f_config_init() to be invoked conditionally, the call to "genphy_soft_reset()" was left as-is, when it should have also been invoked conditionally. This is because the call to "genphy_soft_reset()" was first introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY reset should be issued after setting bits in the PHYCR2 register. As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the rtl8211f_config_init() function by invoking "genphy_soft_reset()" conditionally based on the presence of the "PHYCR2" register. Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05net: phy: mediatek-ge-soc: sync driver with MediaTek SDKDaniel Golle
[ Upstream commit ff63cc2e95065bea978d2db01f7e7356cca3d021 ] Sync initialization and calibration routines with MediaTek's reference driver. Improves compliance and resolves link stability issues with CH340 IoT devices connected to MT798x built-in PHYs. Fixes: 98c485eaf509 ("net: phy: add driver for MediaTek SoC built-in GE PHYs") Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/f2195279c234c0f618946424b8236026126bc595.1706071311.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05net: phy: at803x: fix passing the wrong reference for config_intrChristian Marangi
[ Upstream commit f8fdbf3389f44c7026f16e36cb1f2ff017f7f5b2 ] Fix passing the wrong reference for config_initr on passing the function pointer, drop the wrong & from at803x_config_intr in the PHY struct. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-05net: phy: micrel: fix ts_info value in case of no phcKory Maincent
[ Upstream commit 915d25a9d69be969c1cc6c1dd0c3861f6da7b55e ] In case of no phc we should not return SOFTWARE TIMESTAMPING flags as we do not know whether the netdev supports of timestamping. Remove it from the lan8841_ts_info and simply return 0. Signed-off-by: Kory Maincent <kory.maincent@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-31net: micrel: Fix PTP frame parsing for lan8814Horatiu Vultur
[ Upstream commit aaf632f7ab6dec57bc9329a438f94504fe8034b9 ] The HW has the capability to check each frame if it is a PTP frame, which domain it is, which ptp frame type it is, different ip address in the frame. And if one of these checks fail then the frame is not timestamp. Most of these checks were disabled except checking the field minorVersionPTP inside the PTP header. Meaning that once a partner sends a frame compliant to 8021AS which has minorVersionPTP set to 1, then the frame was not timestamp because the HW expected by default a value of 0 in minorVersionPTP. This is exactly the same issue as on lan8841. Fix this issue by removing this check so the userspace can decide on this. Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-25net: phy: micrel: populate .soft_reset for KSZ9131Claudiu Beznea
[ Upstream commit e398822c4751017fe401f57409488f5948d12fb5 ] The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY is used with the ravb Ethernet driver. It has been discovered that when bringing the Ethernet interface down/up continuously, e.g., with the following sh script: $ while :; do ifconfig eth0 down; ifconfig eth0 up; done the link speed and duplex are wrong after interrupting the bring down/up operation even though the Ethernet interface is up. To recover from this state the following configuration sequence is necessary (executed manually): $ ifconfig eth0 down $ ifconfig eth0 up The behavior has been identified also on the Microchip SAMA7G5-EK board which runs the macb driver and uses the same PHY. The order of PHY-related operations in ravb_open() is as follows: ravb_open() -> ravb_phy_start() -> ravb_phy_init() -> of_phy_connect() -> phy_connect_direct() -> phy_attach_direct() -> phy_init_hw() -> phydev->drv->soft_reset() phydev->drv->config_init() phydev->drv->config_intr() phy_resume() kszphy_resume() The order of PHY-related operations in ravb_close is as follows: ravb_close() -> phy_stop() -> phy_suspend() -> kszphy_suspend() -> genphy_suspend() // set BMCR_PDOWN bit in MII_BMCR In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet). Thus, when opening the interface after it has been previously closed (via ravb_close()), the phydev->drv->config_init() and phydev->drv->config_intr() reach the KSZ9131 PHY driver via the ksz9131_config_init() and kszphy_config_intr() functions. KSZ9131 specifies that the MII management interface remains operational during SPD (Software Power-Down), but (according to manual): - Only access to the standard registers (0 through 31) is supported. - Access to MMD address spaces other than MMD address space 1 is possible if the spd_clock_gate_override bit is set. - Access to MMD address space 1 is not possible. The spd_clock_gate_override bit is not used in the KSZ9131 driver. ksz9131_config_init() configures RGMII delay, pad skews and LEDs by accessesing MMD registers other than those in address space 1. The datasheet for the KSZ9131 does not specify what happens if registers from an unsupported address space are accessed while the PHY is in SPD. To fix the issue the .soft_reset method has been instantiated for KSZ9131, too. This resets the PHY to the default state before doing any configurations to it, thus switching it out of SPD. Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-25net: micrel: Fix PTP frame parsing for lan8841Horatiu Vultur
[ Upstream commit acd66c2126eb9b5da2d89ae07dbcd73b909c2111 ] The HW has the capability to check each frame if it is a PTP frame, which domain it is, which ptp frame type it is, different ip address in the frame. And if one of these checks fail then the frame is not timestamp. Most of these checks were disabled except checking the field minorVersionPTP inside the PTP header. Meaning that once a partner sends a frame compliant to 8021AS which has minorVersionPTP set to 1, then the frame was not timestamp because the HW expected by default a value of 0 in minorVersionPTP. Fix this issue by removing this check so the userspace can decide on this. Fixes: cafc3662ee3f ("net: micrel: Add PHC support for lan8841") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Divya Koppera <divya.koppera@microchip.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-01-01net: phy: skip LED triggers on PHYs on SFP modulesDaniel Golle
[ Upstream commit b1dfc0f76231bbf395c59d20a2070684620d5d0f ] Calling led_trigger_register() when attaching a PHY located on an SFP module potentially (and practically) leads into a deadlock. Fix this by not calling led_trigger_register() for PHYs localted on SFP modules as such modules actually never got any LEDs. ====================================================== WARNING: possible circular locking dependency detected 6.7.0-rc4-next-20231208+ #0 Tainted: G O ------------------------------------------------------ kworker/u8:2/43 is trying to acquire lock: ffffffc08108c4e8 (triggers_list_lock){++++}-{3:3}, at: led_trigger_register+0x4c/0x1a8 but task is already holding lock: ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&sfp->sm_mutex){+.+.}-{3:3}: __mutex_lock+0x88/0x7a0 mutex_lock_nested+0x20/0x28 cleanup_module+0x2ae0/0x3120 [sfp] sfp_register_bus+0x5c/0x9c sfp_register_socket+0x48/0xd4 cleanup_module+0x271c/0x3120 [sfp] platform_probe+0x64/0xb8 really_probe+0x17c/0x3c0 __driver_probe_device+0x78/0x164 driver_probe_device+0x3c/0xd4 __driver_attach+0xec/0x1f0 bus_for_each_dev+0x60/0xa0 driver_attach+0x20/0x28 bus_add_driver+0x108/0x208 driver_register+0x5c/0x118 __platform_driver_register+0x24/0x2c init_module+0x28/0xa7c [sfp] do_one_initcall+0x70/0x2ec do_init_module+0x54/0x1e4 load_module+0x1b78/0x1c8c __do_sys_init_module+0x1bc/0x2cc __arm64_sys_init_module+0x18/0x20 invoke_syscall.constprop.0+0x4c/0xdc do_el0_svc+0x3c/0xbc el0_svc+0x34/0x80 el0t_64_sync_handler+0xf8/0x124 el0t_64_sync+0x150/0x154 -> #2 (rtnl_mutex){+.+.}-{3:3}: __mutex_lock+0x88/0x7a0 mutex_lock_nested+0x20/0x28 rtnl_lock+0x18/0x20 set_device_name+0x30/0x130 netdev_trig_activate+0x13c/0x1ac led_trigger_set+0x118/0x234 led_trigger_write+0x104/0x17c sysfs_kf_bin_write+0x64/0x80 kernfs_fop_write_iter+0x128/0x1b4 vfs_write+0x178/0x2a4 ksys_write+0x58/0xd4 __arm64_sys_write+0x18/0x20 invoke_syscall.constprop.0+0x4c/0xdc do_el0_svc+0x3c/0xbc el0_svc+0x34/0x80 el0t_64_sync_handler+0xf8/0x124 el0t_64_sync+0x150/0x154 -> #1 (&led_cdev->trigger_lock){++++}-{3:3}: down_write+0x4c/0x13c led_trigger_write+0xf8/0x17c sysfs_kf_bin_write+0x64/0x80 kernfs_fop_write_iter+0x128/0x1b4 vfs_write+0x178/0x2a4 ksys_write+0x58/0xd4 __arm64_sys_write+0x18/0x20 invoke_syscall.constprop.0+0x4c/0xdc do_el0_svc+0x3c/0xbc el0_svc+0x34/0x80 el0t_64_sync_handler+0xf8/0x124 el0t_64_sync+0x150/0x154 -> #0 (triggers_list_lock){++++}-{3:3}: __lock_acquire+0x12a0/0x2014 lock_acquire+0x100/0x2ac down_write+0x4c/0x13c led_trigger_register+0x4c/0x1a8 phy_led_triggers_register+0x9c/0x214 phy_attach_direct+0x154/0x36c phylink_attach_phy+0x30/0x60 phylink_sfp_connect_phy+0x140/0x510 sfp_add_phy+0x34/0x50 init_module+0x15c/0xa7c [sfp] cleanup_module+0x1d94/0x3120 [sfp] cleanup_module+0x2bb4/0x3120 [sfp] process_one_work+0x1f8/0x4ec worker_thread+0x1e8/0x3d8 kthread+0x104/0x110 ret_from_fork+0x10/0x20 other info that might help us debug this: Chain exists of: triggers_list_lock --> rtnl_mutex --> &sfp->sm_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&sfp->sm_mutex); lock(rtnl_mutex); lock(&sfp->sm_mutex); lock(triggers_list_lock); *** DEADLOCK *** 4 locks held by kworker/u8:2/43: #0: ffffff80c000f938 ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec #1: ffffffc08214bde8 ((work_completion)(&(&sfp->timeout)->work)){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec #2: ffffffc0810902f8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x18/0x20 #3: ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp] stack backtrace: CPU: 0 PID: 43 Comm: kworker/u8:2 Tainted: G O 6.7.0-rc4-next-20231208+ #0 Hardware name: Bananapi BPI-R4 (DT) Workqueue: events_power_efficient cleanup_module [sfp] Call trace: dump_backtrace+0xa8/0x10c show_stack+0x14/0x1c dump_stack_lvl+0x5c/0xa0 dump_stack+0x14/0x1c print_circular_bug+0x328/0x430 check_noncircular+0x124/0x134 __lock_acquire+0x12a0/0x2014 lock_acquire+0x100/0x2ac down_write+0x4c/0x13c led_trigger_register+0x4c/0x1a8 phy_led_triggers_register+0x9c/0x214 phy_attach_direct+0x154/0x36c phylink_attach_phy+0x30/0x60 phylink_sfp_connect_phy+0x140/0x510 sfp_add_phy+0x34/0x50 init_module+0x15c/0xa7c [sfp] cleanup_module+0x1d94/0x3120 [sfp] cleanup_module+0x2bb4/0x3120 [sfp] process_one_work+0x1f8/0x4ec worker_thread+0x1e8/0x3d8 kthread+0x104/0x110 ret_from_fork+0x10/0x20 Signed-off-by: Daniel Golle <daniel@makrotopia.org> Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs") Link: https://lore.kernel.org/r/102a9dce38bdf00215735d04cd4704458273ad9c.1702339354.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-11-28net: phylink: initialize carrier state at creationKlaus Kudielka
commit 02d5fdbf4f2b8c406f7a4c98fa52aa181a11d733 upstream. Background: Turris Omnia (Armada 385); eth2 (mvneta) connected to SFP bus; SFP module is present, but no fiber connected, so definitely no carrier. After booting, eth2 is down, but netdev LED trigger surprisingly reports link active. Then, after "ip link set eth2 up", the link indicator goes away - as I would have expected it from the beginning. It turns out, that the default carrier state after netdev creation is "carrier ok". Some ethernet drivers explicitly call netif_carrier_off during probing, others (like mvneta) don't - which explains the current behaviour: only when the device is brought up, phylink_start calls netif_carrier_off. Fix this for all drivers using phylink, by calling netif_carrier_off in phylink_create. Fixes: 089381b27abe ("leds: initial support for Turris Omnia LEDs") Cc: stable@vger.kernel.org Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-11-28net: sfp: add quirk for FS's 2.5G copper SFPRaju Lakkaraju
[ Upstream commit e27aca3760c08b7b05aea71068bd609aa93e7b35 ] Add a quirk for a copper SFP that identifies itself as "FS" "SFP-2.5G-T". This module's PHY is inaccessible, and can only run at 2500base-X with the host without negotiation. Add a quirk to enable the 2500base-X interface mode with 2500base-T support and disable auto negotiation. Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> Link: https://lore.kernel.org/r/20230925080059.266240-1-Raju.Lakkaraju@microchip.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-11-28net: sfp: add quirk for Fiberstone GPON-ONU-34-20BIChristian Marangi
[ Upstream commit d387e34fec407f881fdf165b5d7ec128ebff362f ] Fiberstone GPON-ONU-34-20B can operate at 2500base-X, but report 1.2GBd NRZ in their EEPROM. The module also require the ignore tx fault fixup similar to Huawei MA5671A as it gets disabled on error messages with serial redirection enabled. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Link: https://lore.kernel.org/r/20230919124720.8210-1-ansuelsmth@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-10-18net: phy: bcm7xxx: Add missing 16nm EPHY statisticsFlorian Fainelli
The .probe() function would allocate the necessary space and ensure that the library call sizes the number of statistics but the callbacks necessary to fetch the name and values were not wired up. Reported-by: Justin Chen <justin.chen@broadcom.com> Fixes: f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231017205119.416392-1-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-10-10net: phy: mscc: macsec: reject PN update requestsRadu Pirea (NXP OSS)
Updating the PN is not supported. Return -EINVAL if update_pn is true. The following command succeeded, but it should fail because the driver does not update the PN: ip macsec set macsec0 tx sa 0 pn 232 on Fixes: 28c5107aa904 ("net: phy: mscc: macsec support") Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-09-06net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)Lukasz Majewski
The KSZ9477 errata points out (in 'Module 4') the link up/down problems when EEE (Energy Efficient Ethernet) is enabled in the device to which the KSZ9477 tries to auto negotiate. The suggested workaround is to clear advertisement of EEE for PHYs in this chip driver. To avoid regressions with other switch ICs the new MICREL_NO_EEE flag has been introduced. Moreover, the in-register disablement of MMD_DEVICE_ID_EEE_ADV.MMD_EEE_ADV MMD register is removed, as this code is both; now executed too late (after previous rework of the PHY and DSA for KSZ switches) and not required as setting all members of eee_broken_modes bit field prevents the KSZ9477 from advertising EEE. Fixes: 69d3b36ca045 ("net: dsa: microchip: enable EEE support") # for KSZ9477 Signed-off-by: Lukasz Majewski <lukma@denx.de> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # Confirmed disabled EEE with oscilloscope. Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20230905093315.784052-1-lukma@denx.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-25net: phylink: add phylink_limit_mac_speed()Russell King (Oracle)
Add a function which can be used to limit the phylink MAC capabilities to an upper speed limit. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1qZAX3-005pTi-K1@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. Conflicts: include/net/inet_sock.h f866fbc842de ("ipv4: fix data-races around inet->inet_id") c274af224269 ("inet: introduce inet->inet_flags") https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/ Adjacent changes: drivers/net/bonding/bond_alb.c e74216b8def3 ("bonding: fix macvlan over alb bond support") f11e5bd159b0 ("bonding: support balance-alb with openvswitch") drivers/net/ethernet/broadcom/bgmac.c d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()") 23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()") drivers/net/ethernet/broadcom/genet/bcmmii.c 32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()") acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()") net/sctp/socket.c f866fbc842de ("ipv4: fix data-races around inet->inet_id") b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-23dp83640: Use list_for_each_entry() helperJinjie Ruan
Convert list_for_each() to list_for_each_entry() where applicable. No functional changed. Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-19net: phy: Fix deadlocking in phy_error() invocationSerge Semin
Since commit 91a7cda1f4b8 ("net: phy: Fix race condition on link status change") all the phy_error() method invocations have been causing the nested-mutex-lock deadlock because it's normally done in the PHY-driver threaded IRQ handlers which since that change have been called with the phydev->lock mutex held. Here is the calls thread: IRQ: phy_interrupt() +-> mutex_lock(&phydev->lock); <--------------------+ drv->handle_interrupt() | Deadlock due +-> ERROR: phy_error() + to the nested +-> phy_process_error() | mutex lock +-> mutex_lock(&phydev->lock); <-+ phydev->state = PHY_ERROR; mutex_unlock(&phydev->lock); mutex_unlock(&phydev->lock); The problem can be easily reproduced just by calling phy_error() from any PHY-device threaded interrupt handler. Fix it by dropping the phydev->lock mutex lock from the phy_process_error() method and printing a nasty error message to the system log if the mutex isn't held in the caller execution context. Note for the fix to work correctly in the PHY-subsystem itself the phydev->lock mutex locking must be added to the phy_error_precise() function. Link: https://lore.kernel.org/netdev/20230816180944.19262-1-fancer.lancer@gmail.com Fixes: 91a7cda1f4b8 ("net: phy: Fix race condition on link status change") Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-19net: sfp: handle 100G/25G active optical cables in sfp_parse_supportJosua Mayer
Handle extended compliance code 0x1 (SFF8024_ECC_100G_25GAUI_C2M_AOC) for active optical cables supporting 25G and 100G speeds. Since the specification makes no statement about transmitter range, and as the specific sfp module that had been tested features only 2m fiber - short-range (SR) modes are selected. The 100G speed is irrelevant because it would require multiple fibers / multiple SFP28 modules combined under one netdev. sfp-bus.c only handles a single module per netdev, so only 25Gbps modes are selected. sfp_parse_support already handles SFF8024_ECC_100GBASE_SR4_25GBASE_SR with compatible properties, however that entry is a contradiction in itself since with SFP(28) 100GBASE_SR4 is impossible - that would likely be a mode for qsfp modules only. Add a case for SFF8024_ECC_100G_25GAUI_C2M_AOC selecting 25gbase-r interface mode and 25000baseSR link mode. Also enforce SFP28 bitrate limits on the values read from sfp eeprom as requested by Russell King. Tested with fs.com S28-AO02 AOC SFP28 module. Signed-off-by: Josua Mayer <josua@solid-run.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. Conflicts: drivers/net/ethernet/sfc/tc.c fa165e194997 ("sfc: don't unregister flow_indr if it was never registered") 3bf969e88ada ("sfc: add MAE table machinery for conntrack table") https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/ No adjacent changes. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-15net: phy: mediatek-ge-soc: support PHY LEDsDaniel Golle
Implement netdev trigger and primitive bliking offloading as well as simple set_brigthness function for both PHY LEDs of the in-SoC PHYs found in MT7981 and MT7988. For MT7988, read boottrap register and apply LED polarities accordingly to get uniform behavior from all LEDs on MT7988. This requires syscon phandle 'mediatek,pio' present in parenting MDIO bus which should point to the syscon holding the boottrap register. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/dc324d48c00cd7350f3a506eaa785324cae97372.1691977904.git.daniel@makrotopia.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-15net: phy: broadcom: stub c45 read/write for 54810Justin Chen
The 54810 does not support c45. The mmd_phy_indirect accesses return arbirtary values leading to odd behavior like saying it supports EEE when it doesn't. We also see that reading/writing these non-existent MMD registers leads to phy instability in some cases. Fixes: b14995ac2527 ("net: phy: broadcom: Add BCM54810 PHY entry") Signed-off-by: Justin Chen <justin.chen@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/1691901708-28650-1-git-send-email-justin.chen@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-14net: phy: Introduce PSGMII PHY interface modeGabor Juhos
The PSGMII interface is similar to QSGMII. The main difference is that the PSGMII interface combines five SGMII lines into a single link while in QSGMII only four lines are combined. Similarly to the QSGMII, this interface mode might also needs special handling within the MAC driver. It is commonly used by Qualcomm with their QCA807x PHY series and modern WiSoC-s. Add definitions for the PHY layer to allow to express this type of connection between the MAC and PHY. Signed-off-by: Gabor Juhos <j4g8y7@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-13net: phy: fix IRQ-based wake-on-lan over hibernate / power offRussell King (Oracle)
Uwe reports: "Most PHYs signal WoL using an interrupt. So disabling interrupts [at shutdown] breaks WoL at least on PHYs covered by the marvell driver." Discussing with Ioana, the problem which was trying to be solved was: "The board in question is a LS1021ATSN which has two AR8031 PHYs that share an interrupt line. In case only one of the PHYs is probed and there are pending interrupts on the PHY#2 an IRQ storm will happen since there is no entity to clear the interrupt from PHY#2's registers. PHY#1's driver will get stuck in .handle_interrupt() indefinitely." Further confirmation that "the two AR8031 PHYs are on the same MDIO bus." With WoL using interrupts to wake the system, in such a case, the system will begin booting with an asserted interrupt. Thus, we need to cope with an interrupt asserted during boot. Solve this instead by disabling interrupts during PHY probe. This will ensure in Ioana's situation that both PHYs of the same type sharing an interrupt line on a common MDIO bus will have their interrupt outputs disabled when the driver probes the device, but before we hook in any interrupt handlers - thus avoiding the interrupt storm. A better fix would be for platform firmware to disable the interrupting devices at source during boot, before control is handed to the kernel. Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure") Link: 20230804071757.383971-1-u.kleine-koenig@pengutronix.de Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-08-10net: phy: marvell: Add support for offloading LED blinkingAndrew Lunn
Add the code needed to indicate if a given blinking pattern can be offloaded, to offload a pattern and to try to return the current pattern. Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20230808210436.838995-4-andrew@lunn.ch Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-10net: phy: phy_device: Call into the PHY driver to set LED offloadAndrew Lunn
Linux LEDs can be requested to perform hardware accelerated blinking to indicate link, RX, TX etc. Pass the rules for blinking to the PHY driver, if it implements the ops needed to determine if a given pattern can be offloaded, to offload it, and what the current offload is. Additionally implement the op needed to get what device the LED is for. Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/20230808210436.838995-3-andrew@lunn.ch Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-08-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Cross-merge networking fixes after downstream PR. No conflicts. Adjacent changes: drivers/net/ethernet/intel/igc/igc_main.c 06b412589eef ("igc: Add lock to safeguard global Qbv variables") d3750076d464 ("igc: Add TransmissionOverrun counter") drivers/net/ethernet/microsoft/mana/mana_en.c a7dfeda6fdec ("net: mana: Fix MANA VF unload when hardware is unresponsive") a9ca9f9ceff3 ("page_pool: split types and declarations from page_pool.h") 92272ec4107e ("eth: add missing xdp.h includes in drivers") net/mptcp/protocol.h 511b90e39250 ("mptcp: fix disconnect vs accept race") b8dc6d6ce931 ("mptcp: fix rcv buffer auto-tuning") tools/testing/selftests/net/mptcp/mptcp_join.sh c8c101ae390a ("selftests: mptcp: join: fix 'implicit EP' test") 03668c65d153 ("selftests: mptcp: join: rework detailed report") Signed-off-by: Jakub Kicinski <kuba@kernel.org>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-04 00:28:27 +0000