| Age | Commit message (Collapse) | Author |
|---|
|
Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.
Fixes: 4aa17b28 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When trying to get a regulator we may get deferred and we see
this noise:
smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
couldn't get regulators -517
Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.
Fix this by returning silently on deferred probe and let the
system work it out.
Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:
"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.
We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."
We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.
Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QDF2432 and the QDF2400 have slightly different internal PHYs,
so there are some programming differences. Some of the registers in
the QDF2400 have moved, and some registers require different values
during initialization.
Because of the differences, and because HIDs are a scare resource,
the ACPI tables specify the hardware version in an _HRV property.
Version 1 is the QDF2432, and version 2 is the QDF2400. Any future
SOC that has the same internal PHY but different programming
requirements will be assigned the next available version number.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal PHY of the EMAC differs on each SOC, and the list will
only continue to grow. By separating the code into individual files,
we can add support for more SOCs more cleanly.
Note: The internal PHY is also sometimes called the SGMII device.
We also stop referring to the various PHY variations by version number,
so no more "v2", "v3", etc. Instead, the devices are named after the
SOC they are, which is in sync with the device tree property names.
Future patches will probably rearrange more code among the files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some configurations, gcc cannot trace the state of variables
across a spin_unlock() barrier, leading to a warning about
correct code:
xgene_enet_main.c: In function 'xgene_enet_start_xmit':
../../../phy/mdio-xgene.h:112:14: error: 'mss_index' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Here we can trivially move the assignment before that spin_unlock,
which reliably avoids the warning.
Fixes: e3978673f514 ("drivers: net: xgene: Fix MSS programming")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The array for initializing the cle is set up on the stack with
almost entirely constant data and then passed to a function that
converts it into HW specific bit patterns. With the latest
addition, the size of this array has grown to the point that
we get a warning about potential stack overflow in allmodconfig
builds:
xgene_enet_cle.c: In function ‘xgene_enet_cle_init’:
xgene_enet_cle.c:836:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Looking a bit deeper at the usage, I noticed that the only modification
of the data is in dead code, as we don't even use the cle module
for phy_mode other than PHY_INTERFACE_MODE_XGMII. This means we
can simply mark the structure constant and access it directly rather
than passing the pointer down through another structure, making
the code more efficient at the same time as avoiding the
warning.
Fixes: a809701fed15 ("drivers: net: xgene: fix: RSS for non-TCP/UDP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 32-bit ARM with 64-bit dma_addr_t I get this warning about an
incorrect format string:
In file included from /git/arm-soc/drivers/net/ethernet/mellanox/mlx5/core/alloc.c:42:0:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c: In function ‘mlx5_frag_buf_alloc_node’:
drivers/net/ethernet/mellanox/mlx5/core/alloc.c:134:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
We have the special %pad format for printing dma_addr_t, so use that
to print the correct address and avoid the warning.
Fixes: 1c1b522808a1 ("net/mlx5e: Implement Fragmented Work Queue (WQ)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78ed6 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF error handling.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF timestamp.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF ethtool stats
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds VF vxlan offload support.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF vlan features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reserve XDP_PACKET_HEADROOM for packet and enable bpf_xdp_adjust_head()
support. This patch only affects the code path when XDP is active.
After testing, the tx_dropped counter is incremented if the xdp_prog sends
more than wire MTU.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When XDP is active in mlx4, mlx4 is using one page/pkt.
At the same time (i.e. when XDP is active), it is currently
limiting MTU to be FRAG_SZ0 - ETH_HLEN - (2 * VLAN_HLEN)
which is 1514 in x86. AFAICT, we can at least raise the MTU
limit up to PAGE_SIZE - ETH_HLEN - (2 * VLAN_HLEN) which this
patch is doing. It will be useful in the next patch which
allows XDP program to extend the packet by adding new header(s).
Note: In the earlier XDP patches, there is already existing guard
to ensure the page/pkt scheme only applies when XDP is active
in mlx4.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF receive data control path.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for freeing VF xmit buffers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for transmit functionality in VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF scatter gather lists.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for configuring mtu, multicast and mac address.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF link status related changes.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for VF link initialization and offload features.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA_BUS_MODE_RPBL_MASK is really 6 bits,
just like DMA_BUS_MODE_PBL_MASK.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with DT")
changed the parsing of the DT binding.
Before 64c3b252e9fc, snps,fixed-burst and snps,mixed-burst were parsed
regardless if the property snps,pbl existed or not.
After the commit, fixed burst and mixed burst are only parsed if
snps,pbl exists. Now when snps,aal has been added, it too is only
parsed if snps,pbl exists.
Since the DT binding does not specify that fixed burst, mixed burst
or aal depend on snps,pbl being specified, undo changes introduced
by 64c3b252e9fc.
The issue commit 64c3b252e9fc ("net: stmmac: fixed the pbl setting with
DT") tries to address is solved in another way:
The databook specifies that all values other than
1, 2, 4, 8, 16, or 32 results in undefined behavior,
so snps,pbl = <0> is invalid.
If pbl is 0 after parsing, set pbl to DEFAULT_DMA_PBL.
This handles the case where the property is omitted, and also handles
the case where the property is specified without any data.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All drivers except pci glue layer calls stmmac_probe_config_dt.
stmmac_probe_config_dt does a kzalloc dma_cfg.
pci glue layer does kzalloc dma_cfg explicitly, so all current
drivers does a kzalloc dma_cfg.
Return an error if no DMA configuration is found, that way
we can assume that the DMA configuration always exists.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use module_pci_driver() to get rid of some boilerplate code.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.
This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.
If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...
The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.
However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.
No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.
Follows commit b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c047 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These two statements were not indented correctly so it's sort of
confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We never set "slots" in this function.
Fixes: a9380b0f7be8 ("drivers: net: xgene: Add support for Jumbo frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-12-07
This series contains updates to i40e and i40evf only.
Filip modifies the i40e to log link speed change and when the link is
brought up and down.
Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code. Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.
Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+. Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions. Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it. Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters. Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.
Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.
Henry fixes the "ethtool -p" function for 1G BaseT PHYs.
Carolyn adds support for 25G devices for i40e and i40evf.
Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.
v2: dropped last patch from previous series, since changes are needed based
on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063ea ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.
phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.
[ 13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[ 13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[ 13.742115] Hardware name: Axis ARTPEC-6 Platform
[ 13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[ 13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[ 13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[ 13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[ 13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[ 13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[ 13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[ 13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[ 13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[ 13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[ 13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[ 13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[ 13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b83 ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
