| Age | Commit message (Collapse) | Author |
|---|
|
Remove unnecessary early code development check and the WARN_ON
that it uses. The irq alloc and free paths have long been
cleaned up and this check shouldn't have stuck around so long.
Fixes: 77ceb68e29cc ("ionic: Add notifyq support")
Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moved PTP pointer validation before its use to avoid smatch warning.
Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree.
Fixes: 2ef4e45d99b1 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In legacy silicon, promiscuous mode is only modified
through CGX mbox messages. In CN10KB silicon, it is modified
from CGX mbox and NIX. This breaks legacy application
behaviour. Fix this by removing call from NIX.
Fixes: d6c9784baf59 ("octeontx2-af: Invoke exact match functions if supported")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-05 (igc)
This series contains updates to igc driver only.
Husaini adds check to increment Qbv change error counter only on taprio
Qbvs. He also removes delay during Tx ring configuration and
resolves Tx hang that could occur when transmitting on a gate to be
closed.
Prasad Koya reports ethtool link mode as TP (twisted pair).
Tee Min corrects value for max SDU.
Aravindhan ensures that registers for PPS are always programmed to occur
in future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current duplex mode was unset in the driver, resulting in the default
parameter being set to 0, which corresponds to half duplex. It might
mislead users to have incorrect expectation about the driver's
transmission capabilities.
Set the default duplex configuration to full, as the driver runs in
full duplex mode at this point.
Fixes: 7e074d5a76ca ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-05 (ice)
This series contains updates to ice driver only.
Sridhar fixes incorrect comparison of max Tx rate limit to occur against
each TC value rather than the aggregate. He also resolves an issue with
the wrong VSI being used when setting max Tx rate when TCs are enabled.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix tx queue rate limit when TCs are configured
ice: Fix max_rate check while configuring TX rate limits
====================
Link: https://lore.kernel.org/r/20230705201346.49370-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-07-05
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: RX, Fix page_pool page fragment tracking for XDP
net/mlx5: Query hca_cap_2 only when supported
net/mlx5e: TC, CT: Offload ct clear only once
net/mlx5e: Check for NOT_READY flag state after locking
net/mlx5: Register a unique thermal zone per device
net/mlx5e: RX, Fix flush and close release flow of regular rq for legacy rq
net/mlx5e: fix memory leak in mlx5e_ptp_open
net/mlx5e: fix memory leak in mlx5e_fs_tt_redirect_any_create
net/mlx5e: fix double free in mlx5e_destroy_flow_table
====================
Link: https://lore.kernel.org/r/20230705175757.284614-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This switch implements Hold/Release in a strange way, with no control
from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC
and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly
based on the schedule.
Namely, when the gate of a preemptible TC is about to close (actually
QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event),
the QSYS seems to emit a HOLD request pulse towards the MAC which
preempts the currently transmitted packet, and further packets are held
back in the queue system.
This allows large frames to be squeezed through small time slots,
because HOLD requests initiated by the gate events result in the frame
being segmented in multiple fragments, the bit time of which is equal to
the size of the time slot.
It has been reported that the vsc9959_tas_guard_bands_update() logic
breaks this, because it doesn't take preemptible TCs into account, and
enables oversized frame dropping when the time slot doesn't allow a full
MTU to be sent, but it does allow 2*minFragSize to be sent (128B).
Packets larger than 128B are dropped instead of being sent in multiple
fragments.
Confusingly, the manual says:
| For guard band, SDU calculation of a traffic class of a port, if
| preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then
| QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise
| QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used.
but this only refers to the static guard band durations, and the
QMAXSDU_CFG_* registers have dual purpose - the other being oversized
frame dropping, which takes place irrespective of whether frames are
preemptible or express.
So, to fix the problem, we need to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and modify the guard
band logic to consider a different (lower) oversize limit for
preemptible traffic classes.
Fixes: 403ffc2c34de ("net: mscc: ocelot: add support for preemptible traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef987e ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we boot with mvneta.txq_number=1, the txq_map is set incorrectly:
MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is
initialized. Fix this.
Fixes: 50bf8cb6fc9c ("net: mvneta: Configure XPS support")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
|
|
I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.
There were issues reported where PPS is not generated when
start time is in past.
Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"
In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.
Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"
Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.
In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.
1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.
This patch takes care of calculating and programming
appropriate future time value into Target Time registers.
Fixes: 5e91c72e560c ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
IEEE 802.1Q does not have clear definitions of what constitutes an
SDU (Service Data Unit), but IEEE Std 802.3 clause 3.1.2 does define
the MAC service primitives and clause 3.2.7 does define the MAC Client
Data for Q-tagged frames.
It shows that the mac_service_data_unit (MSDU) does NOT contain the
preamble, destination and source address, or FCS. The MSDU does contain
the length/type field, MAC client data, VLAN tag and any padding
data (prior to the FCS).
Thus, the maximum 802.3 frame size that is allowed to be transmitted
should be QueueMaxSDU (MSDU) + 16 (6 byte SA + 6 byte DA + 4 byte FCS).
Fixes: 92a0dcb8427d ("igc: offload queue max SDU from tc-taprio")
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ethtool_link_ksettings
set TP bit in the 'supported' and 'advertising' fields. i225/226 parts
only support twisted pair copper.
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Prasad Koya <prasad@arista.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port.
Fixes: e20aa071cd95 ("nfp: fix schedule in atomic context when sync mc address")
Cc: stable@vger.kernel.org
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Message-ID: <20230705052818.7122-1-louis.peens@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently mlx5e releases pages directly to the page_pool for XDP_TX and
does page fragment counting for XDP_REDIRECT. RX pages from the
page_pool are leaking on XDP_REDIRECT because the xdp core will release
only one fragment out of MLX5E_PAGECNT_BIAS_MAX and subsequently the page
is marked as "skip release" which avoids the driver release.
A fix would be to take an extra fragment for XDP_REDIRECT and not set the
"skip release" bit so that the release on the driver side can handle the
remaining bias fragments. But this would be a shortsighted solution.
Instead, this patch converges the two XDP paths (XDP_TX and XDP_REDIRECT) to
always do fragment tracking. The "skip release" bit is no longer
necessary for XDP.
Fixes: 6f5742846053 ("net/mlx5e: RX, Enable skb page recycling through the page_pool")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
On vport enable, where fw's hca caps are queried, the driver queries
hca_caps_2 without checking if fw truly supports them, causing a false
failure of vfs vport load and blocking SRIOV enablement on old devices
such as CX4 where hca_caps_2 support is missing.
Thus, add a check for the said caps support before accessing them.
Fixes: e5b9642a33be ("net/mlx5: E-Switch, Implement devlink port function cmds to control migratable")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Non-clear CT action causes a flow rule split, while CT clear action
doesn't and is just a header-rewrite to the current flow rule.
But ct offload is done in post_parse and is per ct action instance,
so ct clear offload is parsed multiple times, while its deleted once.
Fix this by post_parsing the ct action only once per flow attribute
(which is per flow rule) by using a offloaded ct_attr flag.
Fixes: 08fe94ec5f77 ("net/mlx5e: TC, Remove special handling of CT action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently the check for NOT_READY flag is performed before obtaining the
necessary lock. This opens a possibility for race condition when the flow
is concurrently removed from unready_flows list by the workqueue task,
which causes a double-removal from the list and a crash[0]. Fix the issue
by moving the flag check inside the section protected by
uplink_priv->unready_flows_lock mutex.
[0]:
[44376.389654] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP
[44376.391665] CPU: 7 PID: 59123 Comm: tc Not tainted 6.4.0-rc4+ #1
[44376.392984] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[44376.395342] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.396857] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.399167] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.399680] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.400337] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.401001] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.401663] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.402342] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.402999] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.403787] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.404343] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.405004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.405665] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[44376.406339] Call Trace:
[44376.406651] <TASK>
[44376.406939] ? die_addr+0x33/0x90
[44376.407311] ? exc_general_protection+0x192/0x390
[44376.407795] ? asm_exc_general_protection+0x22/0x30
[44376.408292] ? mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.408876] __mlx5e_tc_del_fdb_peer_flow+0xbc/0xe0 [mlx5_core]
[44376.409482] mlx5e_tc_del_flow+0x42/0x210 [mlx5_core]
[44376.410055] mlx5e_flow_put+0x25/0x50 [mlx5_core]
[44376.410529] mlx5e_delete_flower+0x24b/0x350 [mlx5_core]
[44376.411043] tc_setup_cb_reoffload+0x22/0x80
[44376.411462] fl_reoffload+0x261/0x2f0 [cls_flower]
[44376.411907] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.412481] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core]
[44376.413044] tcf_block_playback_offloads+0x76/0x170
[44376.413497] tcf_block_unbind+0x7b/0xd0
[44376.413881] tcf_block_setup+0x17d/0x1c0
[44376.414269] tcf_block_offload_cmd.isra.0+0xf1/0x130
[44376.414725] tcf_block_offload_unbind+0x43/0x70
[44376.415153] __tcf_block_put+0x82/0x150
[44376.415532] ingress_destroy+0x22/0x30 [sch_ingress]
[44376.415986] qdisc_destroy+0x3b/0xd0
[44376.416343] qdisc_graft+0x4d0/0x620
[44376.416706] tc_get_qdisc+0x1c9/0x3b0
[44376.417074] rtnetlink_rcv_msg+0x29c/0x390
[44376.419978] ? rep_movs_alternative+0x3a/0xa0
[44376.420399] ? rtnl_calcit.isra.0+0x120/0x120
[44376.420813] netlink_rcv_skb+0x54/0x100
[44376.421192] netlink_unicast+0x1f6/0x2c0
[44376.421573] netlink_sendmsg+0x232/0x4a0
[44376.421980] sock_sendmsg+0x38/0x60
[44376.422328] ____sys_sendmsg+0x1d0/0x1e0
[44376.422709] ? copy_msghdr_from_user+0x6d/0xa0
[44376.423127] ___sys_sendmsg+0x80/0xc0
[44376.423495] ? ___sys_recvmsg+0x8b/0xc0
[44376.423869] __sys_sendmsg+0x51/0x90
[44376.424226] do_syscall_64+0x3d/0x90
[44376.424587] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[44376.425046] RIP: 0033:0x7f045134f887
[44376.425403] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10
[44376.426914] RSP: 002b:00007ffd63a82b98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[44376.427592] RAX: ffffffffffffffda RBX: 000000006481955f RCX: 00007f045134f887
[44376.428195] RDX: 0000000000000000 RSI: 00007ffd63a82c00 RDI: 0000000000000003
[44376.428796] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
[44376.429404] R10: 00007f0451208708 R11: 0000000000000246 R12: 0000000000000001
[44376.430039] R13: 0000000000409980 R14: 000000000047e538 R15: 0000000000485400
[44376.430644] </TASK>
[44376.430907] Modules linked in: mlx5_ib mlx5_core act_mirred act_tunnel_key cls_flower vxlan dummy sch_ingress openvswitch nsh rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_g
ss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc fuse [last unloaded: mlx5_core]
[44376.433936] ---[ end trace 0000000000000000 ]---
[44376.434373] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core]
[44376.434951] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06
[44376.436452] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246
[44376.436924] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00
[44376.437530] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0
[44376.438179] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001
[44376.438786] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000
[44376.439393] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000
[44376.439998] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000
[44376.440714] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[44376.441225] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0
[44376.441843] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[44376.442471] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fixes: ad86755b18d5 ("net/mlx5e: Protect unready flows with dedicated lock")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Prior to this patch only one "mlx5" thermal zone could have been
registered regardless of the number of individual mlx5 devices in the
system.
To fix this setup a unique name per device to register its own thermal
zone.
In order to not register a thermal zone for a virtual device (VF/SF) add
a check for PF device type.
The new name is a concatenation between "mlx5_" and "<PCI_DEV_BDF>", which
will also help associating a thermal zone with its PCI device.
$ lspci | grep ConnectX
00:04.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx]
00:05.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx]
$ cat /sys/devices/virtual/thermal/thermal_zone0/type
mlx5_0000:00:04.0
$ cat /sys/devices/virtual/thermal/thermal_zone1/type
mlx5_0000:00:05.0
Fixes: c1fef618d611 ("net/mlx5: Implement thermal zone")
CC: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Regular (non-XSK) RQs get flushed on XSK setup and re-activated on XSK
close. If the same regular RQ is closed (a config change for example)
soon after the XSK close, a double release occurs because the missing
wqes get released a second time.
Fixes: 3f93f82988bc ("net/mlx5e: RX, Defer page release in legacy rq for better recycling")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When kvzalloc_node or kvzalloc failed in mlx5e_ptp_open, the memory
pointed by "c" or "cparams" is not freed, which can lead to a memory
leak. Fix by freeing the array in the error path.
Fixes: 145e5637d941 ("net/mlx5e: Add TX PTP port object support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The memory pointed to by the fs->any pointer is not freed in the error
path of mlx5e_fs_tt_redirect_any_create, which can lead to a memory leak.
Fix by freeing the memory in the error path, thereby making the error path
identical to mlx5e_fs_tt_redirect_any_destroy().
Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In function accel_fs_tcp_create_groups(), when the ft->g memory is
successfully allocated but the 'in' memory fails to be allocated, the
memory pointed to by ft->g is released once. And in function
accel_fs_tcp_create_table, mlx5e_destroy_flow_table is called to release
the memory pointed to by ft->g again. This will cause double free problem.
Fixes: c062d52ac24c ("net/mlx5e: Receive flow steering framework for accelerated TCP flows")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
If a user schedules a Gate Control List (GCL) to close one of
the QBV gates while also transmitting a packet to that closed gate,
TX Hang will be happen. HW would not drop any packet when the gate
is closed and keep queuing up in HW TX FIFO until the gate is re-opened.
This patch implements the solution to drop the packet for the closed
gate.
This patch will also reset the adapter to perform SW initialization
for each 1st Gate Control List (GCL) to avoid hang.
This is due to the HW design, where changing to TSN transmit mode
requires SW initialization. Intel Discrete I225/6 transmit mode
cannot be changed when in dynamic mode according to Software User
Manual Section 7.5.2.1. Subsequent Gate Control List (GCL) operations
will proceed without a reset, as they already are in TSN Mode.
Step to reproduce:
DUT:
1) Configure GCL List with certain gate close.
BASE=$(date +%s%N)
tc qdisc replace dev $IFACE parent root handle 100 taprio \
num_tc 4 \
map 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 \
queues 1@0 1@1 1@2 1@3 \
base-time $BASE \
sched-entry S 0x8 500000 \
sched-entry S 0x4 500000 \
flags 0x2
2) Transmit the packet to closed gate. You may use udp_tai
application to transmit UDP packet to any of the closed gate.
./udp_tai -i <interface> -P 100000 -p 90 -c 1 -t <0/1> -u 30004
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading")
Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Tested-by: Chwee Lin Choong <chwee.lin.choong@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove unnecessary delay during the TX ring configuration.
This will cause delay, especially during link down and
link up activity.
Furthermore, old SKUs like as I225 will call the reset_adapter
to reset the controller during TSN mode Gate Control List (GCL)
setting. This will add more time to the configuration of the
real-time use case.
It doesn't mentioned about this delay in the Software User Manual.
It might have been ported from legacy code I210 in the past.
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add condition to increase the qbv counter during taprio qbv
configuration only.
There might be a case when TC already been setup then user configure
the ETF/CBS qdisc and this counter will increase if no condition above.
Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Configuring tx_maxrate via sysfs interface
/sys/class/net/eth0/queues/tx-1/tx_maxrate was not working when
TCs are configured because always main VSI was being used. Fix by
using correct VSI in ice_set_tx_maxrate when TCs are configured.
Fixes: 1ddef455f4a8 ("ice: Add NDO callback to set the maximum per-queue bitrate")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove incorrect check in ice_validate_mqprio_opt() that limits
filter configuration when sum of max_rates of all TCs exceeds
the link speed. The max rate of each TC is unrelated to value
used by other TCs and is valid as long as it is less than link
speed.
Fixes: fbc7b27af0f9 ("ice: enable ndo_setup_tc support for mqprio_qdisc")
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
MAC block on CN10K (RPM) supports hardware timestamp configuration. The
previous patch which added timestamp configuration support has a bug.
Though the netdev driver requests to disable timestamp configuration,
the driver is always enabling it.
This patch fixes the same.
Fixes: d1489208681d ("octeontx2-af: cn10k: RPM hardware timestamp configuration")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlxsw_sp_crif_alloc() function returns NULL on error. It doesn't
return error pointers. Fix the check.
Fixes: 78126cfd5dc9 ("mlxsw: spectrum_router: Maintain CRIF for fallback loopback RIF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AF driver configures MAC features like internal loopback and PFC upon
receiving the request from PF and its VF netdev. But these
features are not getting reset in FLR. This patch fixes the issue by
resetting the same.
Fixes: 23999b30ae67 ("octeontx2-af: Enable or disable CGX internal loopback")
Fixes: 1121f6b02e7a ("octeontx2-af: Priority flow control configuration support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
with the addition of new MAC blocks like CN10K RPM and CN10KB
RPM_USX, LMACs are noncontiguous and CGX blocks are also
noncontiguous. But during RVU driver initialization, the driver
is assuming they are contiguous and trying to access
cgx or lmac with their id which is resulting in kernel panic.
This patch fixes the issue by adding proper checks.
[ 23.219150] pc : cgx_lmac_read+0x38/0x70
[ 23.219154] lr : rvu_program_channels+0x3f0/0x498
[ 23.223852] sp : ffff000100d6fc80
[ 23.227158] x29: ffff000100d6fc80 x28: ffff00010009f880 x27:
000000000000005a
[ 23.234288] x26: ffff000102586768 x25: 0000000000002500 x24:
fffffffffff0f000
Fixes: 91c6945ea1f9 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware configures NIX block mapping for all MAC blocks.
The current implementation reads the configuration and
creates the mapping between RVU PF and NIX blocks. But
this configuration is only valid for silicons that support
multiple blocks. For all other silicons, all MAC blocks
map to NIX0.
This patch corrects the mapping by adding a check for the same.
Fixes: c5a73b632b90 ("octeontx2-af: Map NIX block from CGX connection")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current design is that, for asynchronous events like link_up and
link_down firmware raises the interrupt to kernel. The previous patch
which added RPM_USX driver has a bug where it uses old csr addresses
for configuring interrupts. Which is resulting in losing interrupts
from source firmware.
This patch fixes the issue by correcting csr addresses.
Fixes: b9d0fedc6234 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Export pcie_retrain_link() for use outside ASPM
- Add Data Link Layer Link Active Reporting as another way for
pcie_retrain_link() to determine the link is up
- Work around link training failures (especially on the ASMedia
ASM2824 switch) by training first at 2.5GT/s and then attempting
higher rates
Resource management:
- When we coalesce host bridge windows, remove invalidated resources
from the resource tree so future allocations work correctly
Hotplug:
- Cancel bringup sequence if card is not present, to keep from
blinking Power Indicator indefinitely
- Reassign bridge resources if necessary for ACPI hotplug
Driver binding:
- Convert platform_device .remove() callbacks to return void instead
of a mostly useless int
Power management:
- Reduce wait time for secondary bus to be ready to speed up resume
- Avoid putting EloPOS E2/S2/H2 (as well as Elo i2) PCIe Ports in
D3cold
- Call _REG when transitioning D-states so AML that uses the PCI
config space OpRegion works, which fixes some ASMedia GPIO
controllers after resume
Virtualization:
- Delay extra 250ms after FLR of Solidigm P44 Pro NVMe to avoid KVM
hang when guest is rebooted
- Add function 1 DMA alias quirk for Marvell 88SE9235
Error handling:
- Unexport pci_save_aer_state() since it's only used in drivers/pci/
- Drop recommendation for drivers to configure AER Capability, since
the PCI core does this for all devices
ASPM:
- Disable ASPM on MFD function removal to avoid use-after-free
- Tighten up pci_enable_link_state() and pci_disable_link_state()
interfaces so they don't enable/disable states the driver didn't
specify
- Avoid link retraining race that can happen if ASPM sets link
control parameters while the link is in the midst of training for
some other reason
Endpoint framework:
- Change "PCI Endpoint Virtual NTB driver" Kconfig prompt to be
different from "PCI Endpoint NTB driver"
- Automatically create a function specific attributes group for
endpoint drivers to avoid reference counting issues
- Fix many EPC test issues
- Return pci_epf_type_add_cfs() error if EPF has no driver
- Add kernel-doc for pci_epc_raise_irq() and pci_epc_map_msi_irq()
MSI vector parameters
- Pass EPF device ID to driver probe functions
- Return -EALREADY if EPC has already been started/stopped
- Add linkdown notifier support and use it in qcom-ep
- Add Bus Master Enable event support and use it in qcom-ep
- Add Qualcomm Modem Host Interface (MHI) endpoint driver
- Add Layerscape PME interrupt handling to manage link-up
notification
Cadence PCIe controller driver:
- Wait for link retrain to complete when working around the J721E
i2085 erratum with Gen2 mode
Faraday FTPC100 PCI controller driver:
- Release clock resources on error paths
Freescale i.MX6 PCIe controller driver:
- Save and restore Root Port MSI control to work around hardware defect
Intel VMD host bridge driver:
- Reset VMD config register between soft reboots
- Capture pci_reset_bus() return value instead of printing junk when
it fails
Qualcomm PCIe controller driver:
- Add SDX65 endpoint compatible string to DT binding
- Disable register write access after init for IP v2.3.3, v2.9.0
- Use DWC helpers for enabling/disabling writes to DBI registers
- Hide slot hotplug capability for IP v1.0.0, v1.9.0, v2.1.0, v2.3.2,
v2.3.3, v2.7.0, v2.9.0
- Reuse v2.3.2 post-init sequence for v2.4.0
Renesas R-Car PCIe controller driver:
- Remove unused static pcie_base and pcie_dev
Rockchip PCIe controller driver:
- Remove writes to unused registers
- Write endpoint Device ID using correct register
- Assert PCI Configuration Enable bit after probe so endpoint
responds instead of generating Request Retry Status messages
- Poll waiting for PHY PLLs to lock
- Update RK3399 example DT binding to be valid
- Use RK3399 PCIE_CLIENT_LEGACY_INT_CTRL to generate INTx instead of
manually generating PCIe message
- Use multiple windows to avoid address translation conflicts
- Use u32 (not u16) when accessing 32-bit registers
- Hide MSI-X Capability, since RK3399 can't generate MSI-X
- Set endpoint controller required alignment to 256
Synopsys DesignWare PCIe controller driver:
- Wait for link to come up only if we've initiated link training
Miscellaneous:
- Add pci_clear_master() stub for non-CONFIG_PCI"
* tag 'pci-v6.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (116 commits)
Documentation: PCI: correct spelling
PCI: vmd: Fix uninitialized variable usage in vmd_enable_domain()
PCI: xgene-msi: Convert to platform remove callback returning void
PCI: tegra: Convert to platform remove callback returning void
PCI: rockchip-host: Convert to platform remove callback returning void
PCI: mvebu: Convert to platform remove callback returning void
PCI: mt7621: Convert to platform remove callback returning void
PCI: mediatek-gen3: Convert to platform remove callback returning void
PCI: mediatek: Convert to platform remove callback returning void
PCI: iproc: Convert to platform remove callback returning void
PCI: hisi-error: Convert to platform remove callback returning void
PCI: dwc: Convert to platform remove callback returning void
PCI: j721e: Convert to platform remove callback returning void
PCI: brcmstb: Convert to platform remove callback returning void
PCI: altera-msi: Convert to platform remove callback returning void
PCI: altera: Convert to platform remove callback returning void
PCI: aardvark: Convert to platform remove callback returning void
PCI: rcar: Use correct product family name for Renesas R-Car
PCI: layerscape: Add the endpoint linkup notifier support
PCI: endpoint: pci-epf-vntb: Fix typo in comments
...
|
|
Pull rdma updates from Jason Gunthorpe:
"This cycle saw a focus on rxe and bnxt_re drivers:
- Code cleanups for irdma, rxe, rtrs, hns, vmw_pvrdma
- rxe uses workqueues instead of tasklets
- rxe has better compliance around access checks for MRs and rereg_mr
- mana supportst he 'v2' FW interface for RX coalescing
- hfi1 bug fix for stale cache entries in its MR cache
- mlx5 buf fix to handle FW failures when destroying QPs
- erdma HW has a new doorbell allocation mechanism for uverbs that is
secure
- Lots of small cleanups and rework in bnxt_re:
- Use the common mmap functions
- Support disassociation
- Improve FW command flow
- support for 'low latency push'"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (71 commits)
RDMA/bnxt_re: Fix an IS_ERR() vs NULL check
RDMA/bnxt_re: Fix spelling mistake "priviledged" -> "privileged"
RDMA/bnxt_re: Remove duplicated include in bnxt_re/main.c
RDMA/bnxt_re: Refactor code around bnxt_qplib_map_rc()
RDMA/bnxt_re: Remove incorrect return check from slow path
RDMA/bnxt_re: Enable low latency push
RDMA/bnxt_re: Reorg the bar mapping
RDMA/bnxt_re: Move the interface version to chip context structure
RDMA/bnxt_re: Query function capabilities from firmware
RDMA/bnxt_re: Optimize the bnxt_re_init_hwrm_hdr usage
RDMA/bnxt_re: Add disassociate ucontext support
RDMA/bnxt_re: Use the common mmap helper functions
RDMA/bnxt_re: Initialize opcode while sending message
RDMA/cma: Remove NULL check before dev_{put, hold}
RDMA/rxe: Simplify cq->notify code
RDMA/rxe: Fixes mr access supported list
RDMA/bnxt_re: optimize the parameters passed to helper functions
RDMA/bnxt_re: remove redundant cmdq_bitmap
RDMA/bnxt_re: use firmware provided max request timeout
RDMA/bnxt_re: cancel all control path command waiters upon error
...
|
|
The line cards array is not freed in the error path of
mlxsw_m_linecards_init(), which can lead to a memory leak. Fix by
freeing the array in the error path, thereby making the error path
identical to mlxsw_m_linecards_fini().
Fixes: 01328e23a476 ("mlxsw: minimal: Extend module to port mapping with slot index")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230630012647.1078002-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Nothing surprising in the SoC specific drivers, with the usual
updates:
- Added or improved SoC driver support for Tegra234, Exynos4121,
RK3588, as well as multiple Mediatek and Qualcomm chips
- SCMI firmware gains support for multiple SMC/HVC transport and
version 3.2 of the protocol
- Cleanups amd minor changes for the reset controller, memory
controller, firmware and sram drivers
- Minor changes to amd/xilinx, samsung, tegra, nxp, ti, qualcomm,
amlogic and renesas SoC specific drivers"
* tag 'soc-drivers-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (118 commits)
dt-bindings: interrupt-controller: Convert Amlogic Meson GPIO interrupt controller binding
MAINTAINERS: add PHY-related files to Amlogic SoC file list
drivers: meson: secure-pwrc: always enable DMA domain
tee: optee: Use kmemdup() to replace kmalloc + memcpy
soc: qcom: geni-se: Do not bother about enable/disable of interrupts in secondary sequencer
dt-bindings: sram: qcom,imem: document qdu1000
soc: qcom: icc-bwmon: Fix MSM8998 count unit
dt-bindings: soc: qcom,rpmh-rsc: Require power-domains
soc: qcom: socinfo: Add Soc ID for IPQ5300
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5300
soc: qcom: Fix a IS_ERR() vs NULL bug in probe
soc: qcom: socinfo: Add support for new fields in revision 19
soc: qcom: socinfo: Add support for new fields in revision 18
dt-bindings: firmware: scm: Add compatible for SDX75
soc: qcom: mdt_loader: Fix split image detection
dt-bindings: memory-controllers: drop unneeded quotes
soc: rockchip: dtpm: use C99 array init syntax
firmware: tegra: bpmp: Add support for DRAM MRQ GSCs
soc/tegra: pmc: Use devm_clk_notifier_register()
soc/tegra: pmc: Simplify debugfs initialization
...
|
|
All ibmvnic resets, make a call to netdev_tx_reset_queue() when
re-opening the device. netdev_tx_reset_queue() resets the num_queued
and num_completed byte counters. These stats are used in Byte Queue
Limit (BQL) algorithms. The difference between these two stats tracks
the number of bytes currently sitting on the physical NIC. ibmvnic
increases the number of queued bytes though calls to
netdev_tx_sent_queue() in the drivers xmit function. When, VIOS reports
that it is done transmitting bytes, the ibmvnic device increases the
number of completed bytes through calls to netdev_tx_completed_queue().
It is important to note that the driver batches its transmit calls and
num_queued is increased every time that an skb is added to the next
batch, not necessarily when the batch is sent to VIOS for transmission.
Unlike other reset types, a NON FATAL reset will not flush the sub crq
tx buffers. Therefore, it is possible for the batched skb array to be
partially full. So if there is call to netdev_tx_reset_queue() when
re-opening the device, the value of num_queued (0) would not account
for the skb's that are currently batched. Eventually, when the batch
is sent to VIOS, the call to netdev_tx_completed_queue() would increase
num_completed to a value greater than the num_queued. This causes a
BUG_ON crash:
ibmvnic 30000002: Firmware reports error, cause: adapter problem.
Starting recovery...
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
ibmvnic 30000002: tx error 600
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:27!
Oops: Exception in kernel mode, sig: 5
[....]
NIP dql_completed+0x28/0x1c0
LR ibmvnic_complete_tx.isra.0+0x23c/0x420 [ibmvnic]
Call Trace:
ibmvnic_complete_tx.isra.0+0x3f8/0x420 [ibmvnic] (unreliable)
ibmvnic_interrupt_tx+0x40/0x70 [ibmvnic]
__handle_irq_event_percpu+0x98/0x270
---[ end trace ]---
Therefore, do not reset the dql stats when performing a NON_FATAL reset.
Fixes: 0d973388185d ("ibmvnic: Introduce xmit_more support using batched subCRQ hcalls")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On systems without MAE permission efx->mae is not initialised,
and trying to lookup an mport results in a NULL pointer
dereference.
Fixes: 25414b2a64ae ("sfc: add devlink port support for ef100")
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes a bug where on the M1 mac mini initramfs-tools fails to
include the necessary firmware into the initrd.
Fixes: c4dab50697ff ("tg3: Download 57766 EEE service patch firmware")
Signed-off-by: Tobias Heider <me@tobhe.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/ZJt7LKzjdz8+dClx@tobhe.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PTP RX timestamping should be enabled when the user requests it, not by
default. If it is enabled by default, it can be problematic when the
ocelot driver is a DSA master, and it sidesteps what DSA tries to avoid
through __dsa_master_hwtstamp_validate().
Additionally, after the change which made ocelot trap PTP packets only
to the CPU at ocelot_hwtstamp_set() time, it is no longer even true that
RX timestamping is enabled by default, because until ocelot_hwtstamp_set()
is called, the PTP traps are actually not set up. So the rx_filter field
of ocelot->hwtstamp_config reflects an incorrect reality.
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
dev_set_rx_mode() grabs a spin_lock, and the lan743x implementation
proceeds subsequently to go to sleep using readx_poll_timeout().
Introduce a helper wrapping the readx_poll_timeout_atomic() function
and use it to replace the calls to readx_polL_timeout().
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver")
Cc: stable@vger.kernel.org
Cc: Bryan Whitehead <bryan.whitehead@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230627035000.1295254-1-moritzf@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"There are three areas of note:
A bunch of strlcpy()->strscpy() conversions ended up living in my tree
since they were either Acked by maintainers for me to carry, or got
ignored for multiple weeks (and were trivial changes).
The compiler option '-fstrict-flex-arrays=3' has been enabled
globally, and has been in -next for the entire devel cycle. This
changes compiler diagnostics (though mainly just -Warray-bounds which
is disabled) and potential UBSAN_BOUNDS and FORTIFY _warning_
coverage. In other words, there are no new restrictions, just
potentially new warnings. Any new FORTIFY warnings we've seen have
been fixed (usually in their respective subsystem trees). For more
details, see commit df8fc4e934c12b.
The under-development compiler attribute __counted_by has been added
so that we can start annotating flexible array members with their
associated structure member that tracks the count of flexible array
elements at run-time. It is possible (likely?) that the exact syntax
of the attribute will change before it is finalized, but GCC and Clang
are working together to sort it out. Any changes can be made to the
macro while we continue to add annotations.
As an example of that last case, I have a treewide commit waiting with
such annotations found via Coccinelle:
https://git.kernel.org/linus/adc5b3cb48a049563dc673f348eab7b6beba8a9b
Also see commit dd06e72e68bcb4 for more details.
Summary:
- Fix KMSAN vs FORTIFY in strlcpy/strlcat (Alexander Potapenko)
- Convert strreplace() to return string start (Andy Shevchenko)
- Flexible array conversions (Arnd Bergmann, Wyes Karny, Kees Cook)
- Add missing function prototypes seen with W=1 (Arnd Bergmann)
- Fix strscpy() kerndoc typo (Arne Welzel)
- Replace strlcpy() with strscpy() across many subsystems which were
either Acked by respective maintainers or were trivial changes that
went ignored for multiple weeks (Azeem Shaikh)
- Remove unneeded cc-option test for UBSAN_TRAP (Nick Desaulniers)
- Add KUnit tests for strcat()-family
- Enable KUnit tests of FORTIFY wrappers under UML
- Add more complete FORTIFY protections for strlcat()
- Add missed disabling of FORTIFY for all arch purgatories.
- Enable -fstrict-flex-arrays=3 globally
- Tightening UBSAN_BOUNDS when using GCC
- Improve checkpatch to check for strcpy, strncpy, and fake flex
arrays
- Improve use of const variables in FORTIFY
- Add requested struct_size_t() helper for types not pointers
- Add __counted_by macro for annotating flexible array size members"
* tag 'hardening-v6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (54 commits)
netfilter: ipset: Replace strlcpy with strscpy
uml: Replace strlcpy with strscpy
um: Use HOST_DIR for mrproper
kallsyms: Replace all non-returning strlcpy with strscpy
sh: Replace all non-returning strlcpy with strscpy
of/flattree: Replace all non-returning strlcpy with strscpy
sparc64: Replace all non-returning strlcpy with strscpy
Hexagon: Replace all non-returning strlcpy with strscpy
kobject: Use return value of strreplace()
lib/string_helpers: Change returned value of the strreplace()
jbd2: Avoid printing outside the boundary of the buffer
checkpatch: Check for 0-length and 1-element arrays
riscv/purgatory: Do not use fortified string functions
s390/purgatory: Do not use fortified string functions
x86/purgatory: Do not use fortified string functions
acpi: Replace struct acpi_table_slit 1-element array with flex-array
clocksource: Replace all non-returning strlcpy with strscpy
string: use __builtin_memcpy() in strlcpy/strlcat
staging: most: Replace all non-returning strlcpy with strscpy
drm/i2c: tda998x: Replace all non-returning strlcpy with strscpy
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull ordered workqueue creation updates from Tejun Heo:
"For historical reasons, unbound workqueues with max concurrency limit
of 1 are considered ordered, even though the concurrency limit hasn't
been system-wide for a long time.
This creates ambiguity around whether ordered execution is actually
required for correctness, which was actually confusing for e.g. btrfs
(btrfs updates are being routed through the btrfs tree).
There aren't that many users in the tree which use the combination and
there are pending improvements to unbound workqueue affinity handling
which will make inadvertent use of ordered workqueue a bigger loss.
This clarifies the situation for most of them by updating the ones
which require ordered execution to use alloc_ordered_workqueue().
There are some conversions being routed through subsystem-specific
trees and likely a few stragglers. Once they're all converted,
workqueue can trigger a warning on unbound + @max_active==1 usages and
eventually drop the implicit ordered behavior"
* tag 'wq-for-6.5-cleanup-ordered' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
rxrpc: Use alloc_ordered_workqueue() to create ordered workqueues
net: qrtr: Use alloc_ordered_workqueue() to create ordered workqueues
net: wwan: t7xx: Use alloc_ordered_workqueue() to create ordered workqueues
dm integrity: Use alloc_ordered_workqueue() to create ordered workqueues
media: amphion: Use alloc_ordered_workqueue() to create ordered workqueues
scsi: NCR5380: Use default @max_active for hostdata->work_q
media: coda: Use alloc_ordered_workqueue() to create ordered workqueues
crypto: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: ath10/11/12k: Use alloc_ordered_workqueue() to create ordered workqueues
wifi: mwifiex: Use default @max_active for workqueues
wifi: iwlwifi: Use default @max_active for trans_pcie->rba.alloc_wq
xen/pvcalls: Use alloc_ordered_workqueue() to create ordered workqueues
virt: acrn: Use alloc_ordered_workqueue() to create ordered workqueues
net: octeontx2: Use alloc_ordered_workqueue() to create ordered workqueues
net: thunderx: Use alloc_ordered_workqueue() to create ordered workqueues
greybus: Use alloc_ordered_workqueue() to create ordered workqueues
powerpc, workqueue: Use alloc_ordered_workqueue() to create ordered workqueues
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into soc/drivers
NXP/FSL SoC driver updates for v6.5
- fsl-mc: Make remove function return void
- QE USB: fix build issue caused by missing dependency
* tag 'soc-fsl-next-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
bus: fsl-mc: fsl-mc-allocator: Drop a write-only variable
bus: fsl-mc: fsl-mc-allocator: Initialize mc_bus_dev before use
soc/fsl/qe: fix usb.c build errors
bus: fsl-mc: Make remove function return void
soc: fsl: dpio: Suppress duplicated error reporting on device remove
bus: fsl-mc: fsl-mc-allocator: Improve error reporting
bus: fsl-mc: fsl-mc-allocator: Drop if block with always wrong condition
bus: fsl-mc: dprc: Push down error message from fsl_mc_driver_remove()
bus: fsl-mc: Only warn once about errors on device unbind
Link: https://lore.kernel.org/r/20230621222503.12402-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Linux 6.4
Resolve conflicts between rdma rc and next in rxe_cq matching linux-next:
drivers/infiniband/sw/rxe/rxe_cq.c:
https://lore.kernel.org/r/20230622115246.365d30ad@canb.auug.org.au
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
