summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet
AgeCommit message (Collapse)Author
2023-07-12net: txgbe: fix eeprom calculation errorJiawen Wu
For some device types like TXGBE_ID_XAUI, *checksum computed in txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the limit on the size of *checksum. Fixes: 049fe5365324 ("net: txgbe: Add operations to interact with firmware") Fixes: 5e2ea7801fac ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-12net: ena: fix shift-out-of-bounds in exponential backoffKrister Johansen
The ENA adapters on our instances occasionally reset. Once recently logged a UBSAN failure to console in the process: UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13 shift exponent 32 is too large for 32-bit type 'unsigned int' CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117 Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017 Workqueue: ena ena_fw_reset_device [ena] Call Trace: <TASK> dump_stack_lvl+0x4a/0x63 dump_stack+0x10/0x16 ubsan_epilogue+0x9/0x36 __ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e ? __const_udelay+0x43/0x50 ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena] wait_for_reset_state+0x54/0xa0 [ena] ena_com_dev_reset+0xc8/0x110 [ena] ena_down+0x3fe/0x480 [ena] ena_destroy_device+0xeb/0xf0 [ena] ena_fw_reset_device+0x30/0x50 [ena] process_one_work+0x22b/0x3d0 worker_thread+0x4d/0x3f0 ? process_one_work+0x3d0/0x3d0 kthread+0x12a/0x150 ? set_kthread_struct+0x50/0x50 ret_from_fork+0x22/0x30 </TASK> Apparently, the reset delays are getting so large they can trigger a UBSAN panic. Looking at the code, the current timeout is capped at 5000us. Using a base value of 100us, the current code will overflow after (1<<29). Even at values before 32, this function wraps around, perhaps unintentionally. Cap the value of the exponent used for this backoff at (1<<16) which is larger than currently necessary, but large enough to support bigger values in the future. Cc: stable@vger.kernel.org Fixes: 4bb7f4cf60e3 ("net: ena: reduce driver load time") Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Shay Agroskin <shayagr@amazon.com> Link: https://lore.kernel.org/r/20230711013621.GE1926@templeofstupid.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-12Merge branch '1GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== igc: Fix corner cases for TSN offload Florian Kauer says: The igc driver supports several different offloading capabilities relevant in the TSN context. Recent patches in this area introduced regressions for certain corner cases that are fixed in this series. Each of the patches (except the first one) addresses a different regression that can be separately reproduced. Still, they have overlapping code changes so they should not be separately applied. Especially #4 and #6 address the same observation, but both need to be applied to avoid TX hang occurrences in the scenario described in the patches. ==================== Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-11octeontx2-pf: Add additional check for MCAM rulesSuman Ghosh
Due to hardware limitation, MCAM drop rule with ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting such rules. Fixes: dce677da57c0 ("octeontx2-pf: Add vlan-etype to ntuple filters") Signed-off-by: Suman Ghosh <sumang@marvell.com> Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-11net: fec: use netdev_err_once() instead of netdev_err()Wei Fang
In the case of heavy XDP traffic to be transmitted, the console will print the error log continuously if there are lack of enough BDs to accommodate the frames. The log looks like below. [ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG! Not only will this log be replicated and redundant, it will also degrade XDP performance. So we use netdev_err_once() instead of netdev_err() now. Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support") Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-11net: fec: increase the size of tx ring and update tx_wake_thresholdWei Fang
When the XDP feature is enabled and with heavy XDP frames to be transmitted, there is a considerable probability that available tx BDs are insufficient. This will lead to some XDP frames to be discarded and the "NOT enough BD for SG!" error log will appear in the console (as shown below). [ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG! [ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG! In the case of heavy XDP traffic, sometimes the speed of recycling tx BDs may be slower than the speed of sending XDP frames. There may be several specific reasons, such as the interrupt is not responsed in time, the efficiency of the NAPI callback function is too low due to all the queues (tx queues and rx queues) share the same NAPI, and so on. After trying various methods, I think that increase the size of tx BD ring is simple and effective. Maybe the best resolution is that allocate NAPI for each queue to improve the efficiency of the NAPI callback, but this change is a bit big and I didn't try this method. Perheps this method will be implemented in a future patch. This patch also updates the tx_wake_threshold of tx ring which is related to the size of tx ring in the previous logic. Otherwise, the tx_wake_threshold will be too high (403 BDs), which is more likely to impact the slow path in the case of heavy XDP traffic, because XDP path and slow path share the tx BD rings. According to Jakub's suggestion, the tx_wake_threshold is at least equal to tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of entries is overflowing, we should be able to apply a hysteresis of a few tens of entries. Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support") Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-11net: fec: recycle pages for transmitted XDP framesWei Fang
Once the XDP frames have been successfully transmitted through the ndo_xdp_xmit() interface, it's the driver responsibility to free the frames so that the page_pool can recycle the pages and reuse them. However, this action is not implemented in the fec driver. This leads to a user-visible problem that the console will print the following warning log. [ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec [ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec [ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec [ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec [ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec Therefore, to solve this issue, we free XDP frames via xdp_return_frame() while cleaning the tx BD ring. Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support") Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-11net: fec: dynamically set the NETDEV_XDP_ACT_NDO_XMIT feature of XDPWei Fang
When a XDP program is installed or uninstalled, fec_restart() will be invoked to reset MAC and buffer descriptor rings. It's reasonable not to transmit any packet during the process of reset. However, the NETDEV_XDP_ACT_NDO_XMIT bit of xdp_features is enabled by default, that is to say, it's possible that the fec_enet_xdp_xmit() will be invoked even if the process of reset is not finished. In this case, the redirected XDP frames might be dropped and available transmit BDs may be incorrectly deemed insufficient. So this patch disable the NETDEV_XDP_ACT_NDO_XMIT feature by default and dynamically configure this feature when the bpf program is installed or uninstalled. Fixes: e4ac7cc6e5a4 ("net: fec: turn on XDP features") Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-10igc: Fix inserting of empty frame for launchtimeFlorian Kauer
The insertion of an empty frame was introduced with commit db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit") in order to ensure that the current cycle has at least one packet if there is some packet to be scheduled for the next cycle. However, the current implementation does not properly check if a packet is already scheduled for the current cycle. Currently, an empty packet is always inserted if and only if txtime >= end_of_cycle && txtime > last_tx_cycle but since last_tx_cycle is always either the end of the current cycle (end_of_cycle) or the end of a previous cycle, the second part (txtime > last_tx_cycle) is always true unless txtime == last_tx_cycle. What actually needs to be checked here is if the last_tx_cycle was already written within the current cycle, so an empty frame should only be inserted if and only if txtime >= end_of_cycle && end_of_cycle > last_tx_cycle. This patch does not only avoid an unnecessary insertion, but it can actually be harmful to insert an empty packet if packets are already scheduled in the current cycle, because it can lead to a situation where the empty packet is actually processed as the first packet in the upcoming cycle shifting the packet with the first_flag even one cycle into the future, finally leading to a TX hang. The TX hang can be reproduced on a i225 with: sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \ num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 \ base-time 0 \ sched-entry S 01 300000 \ flags 0x1 \ txtime-delay 500000 \ clockid CLOCK_TAI sudo tc qdisc replace dev enp1s0 parent 100:1 etf \ clockid CLOCK_TAI \ delta 500000 \ offload \ skip_sock_check and traffic generator sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns with traffic.cfg #define ETH_P_IP 0x0800 { /* Ethernet Header */ 0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed 0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed const16(ETH_P_IP), /* IPv4 Header */ 0b01000101, 0, # IPv4 version, IHL, TOS const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header)) const16(2), # IPv4 ident 0b01000000, 0, # IPv4 flags, fragmentation off 64, # IPv4 TTL 17, # Protocol UDP csumip(14, 33), # IPv4 checksum /* UDP Header */ 10, 0, 48, 1, # IP Src - adapt as needed 10, 0, 48, 10, # IP Dest - adapt as needed const16(5555), # UDP Src Port const16(6666), # UDP Dest Port const16(1008), # UDP length (UDP header 8 bytes + payload length) csumudp(14, 34), # UDP checksum /* Payload */ fill('W', 1000), } and the observed message with that is for example igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang Tx Queue <0> TDH <32> TDT <3c> next_to_use <3c> next_to_clean <32> buffer_info[next_to_clean] time_stamp <ffff26a8> next_to_watch <00000000632a1828> jiffies <ffff27f8> desc.status <1048000> Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10igc: Fix launchtime before start of cycleFlorian Kauer
It is possible (verified on a running system) that frames are processed by igc_tx_launchtime with a txtime before the start of the cycle (baset_est). However, the result of txtime - baset_est is written into a u32, leading to a wrap around to a positive number. The following launchtime > 0 check will only branch to executing launchtime = 0 if launchtime is already 0. Fix it by using a s32 before checking launchtime > 0. Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10igc: No strict mode in pure launchtime/CBS offloadFlorian Kauer
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END prevent the packet transmission over slot and cycle boundaries. This is important for taprio offload where the slots and cycles correspond to the slots and cycles configured for the network. However, the Qbv offload feature of the i225 is also used for enabling TX launchtime / ETF offload. In that case, however, the cycle has no meaning for the network and is only used internally to adapt the base time register after a second has passed. Enabling strict mode in this case would unnecessarily prevent the transmission of certain packets (i.e. at the boundary of a second) and thus interferes with the ETF qdisc that promises transmission at a certain point in time. Similar to ETF, this also applies to CBS offload that also should not be influenced by strict mode unless taprio offload would be enabled at the same time. This fully reverts commit d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling") but its commit message only describes what was already implemented before that commit. The difference to a plain revert of that commit is that it now copes with the base_time = 0 case that was fixed with commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv") In particular, enabling strict mode leads to TX hang situations under high traffic if taprio is applied WITHOUT taprio offload but WITH ETF offload, e.g. as in sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \ num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 \ base-time 0 \ sched-entry S 01 300000 \ flags 0x1 \ txtime-delay 500000 \ clockid CLOCK_TAI sudo tc qdisc replace dev enp1s0 parent 100:1 etf \ clockid CLOCK_TAI \ delta 500000 \ offload \ skip_sock_check and traffic generator sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns with traffic.cfg #define ETH_P_IP 0x0800 { /* Ethernet Header */ 0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed 0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed const16(ETH_P_IP), /* IPv4 Header */ 0b01000101, 0, # IPv4 version, IHL, TOS const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header)) const16(2), # IPv4 ident 0b01000000, 0, # IPv4 flags, fragmentation off 64, # IPv4 TTL 17, # Protocol UDP csumip(14, 33), # IPv4 checksum /* UDP Header */ 10, 0, 48, 1, # IP Src - adapt as needed 10, 0, 48, 10, # IP Dest - adapt as needed const16(5555), # UDP Src Port const16(6666), # UDP Dest Port const16(1008), # UDP length (UDP header 8 bytes + payload length) csumudp(14, 34), # UDP checksum /* Payload */ fill('W', 1000), } and the observed message with that is for example igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang Tx Queue <0> TDH <d0> TDT <f0> next_to_use <f0> next_to_clean <d0> buffer_info[next_to_clean] time_stamp <ffff661f> next_to_watch <00000000245a4efb> jiffies <ffff6e48> desc.status <1048000> Fixes: d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10igc: Handle already enabled taprio offload for basetime 0Florian Kauer
Since commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv") it is possible to enable taprio offload with a basetime of 0. However, the check if taprio offload is already enabled (and thus -EALREADY should be returned for igc_save_qbv_schedule) still relied on adapter->base_time > 0. This can be reproduced as follows: # TAPRIO offload (flags == 0x2) and base-time = 0 sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \ num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 \ base-time 0 \ sched-entry S 01 300000 \ flags 0x2 # The second call should fail with "Error: Device failed to setup taprio offload." # But that only happens if base-time was != 0 sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \ num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 \ base-time 0 \ sched-entry S 01 300000 \ flags 0x2 Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10igc: Do not enable taprio offload for invalid argumentsFlorian Kauer
Only set adapter->taprio_offload_enable after validating the arguments. Otherwise, it stays set even if the offload was not enabled. Since the subsequent code does not get executed in case of invalid arguments, it will not be read at first. However, by activating and then deactivating another offload (e.g. ETF/TX launchtime offload), taprio_offload_enable is read and erroneously keeps the offload feature of the NIC enabled. This can be reproduced as follows: # TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \ num_tc 1 \ map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \ queues 1@0 \ base-time -1000 \ sched-entry S 01 300000 \ flags 0x2 # IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register) sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1 # Activate ETF offload sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \ num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \ queues 1@0 1@1 2@2 \ hw 0 sudo tc qdisc add dev enp1s0 parent 6666:1 etf \ clockid CLOCK_TAI \ delta 500000 \ offload # IGC_TQAVCTRL is 0x9 as expected sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1 # Deactivate ETF offload again sudo tc qdisc delete dev enp1s0 parent 6666:1 # IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9 sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1 Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10igc: Rename qbv_enable to taprio_offload_enableFlorian Kauer
In the current implementation the flags adapter->qbv_enable and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not have the same meaning. The first one is used only to indicate taprio offload (i.e. when igc_save_qbv_schedule was called), while the second one corresponds to the Qbv mode of the hardware. However, the second one is also used to support the TX launchtime feature, i.e. ETF qdisc offload. This leads to situations where adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED is set. This is prone to confusion. The rename should reduce this confusion. Since it is a pure rename, it has no impact on functionality. Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv") Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-10gve: unify driver name usageJunfeng Guo
Current codebase contained the usage of two different names for this driver (i.e., `gvnic` and `gve`), which is quite unfriendly for users to use, especially when trying to bind or unbind the driver manually. The corresponding kernel module is registered with the name of `gve`. It's more reasonable to align the name of the driver with the module. Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC") Cc: csully@google.com Signed-off-by: Junfeng Guo <junfeng.guo@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-09net: lan743x: select FIXED_PHYSimon Horman
The blamed commit introduces usage of fixed_phy_register() but not a corresponding dependency on FIXED_PHY. This can result in a build failure. s390-linux-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_phy_open': drivers/net/ethernet/microchip/lan743x_main.c:1514: undefined reference to `fixed_phy_register' Fixes: 624864fbff92 ("net: lan743x: add fixed phy support for LAN7431 device") Cc: stable@vger.kernel.org Reported-by: Randy Dunlap <rdunlap@infradead.org> Closes: https://lore.kernel.org/netdev/725bf1c5-b252-7d19-7582-a6809716c7d6@infradead.org/ Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-08net: bgmac: postpone turning IRQs off to avoid SoC hangsRafał Miłecki
Turning IRQs off is done by accessing Ethernet controller registers. That can't be done until device's clock is enabled. It results in a SoC hang otherwise. This bug remained unnoticed for years as most bootloaders keep all Ethernet interfaces turned on. It seems to only affect a niche SoC family BCM47189. It has two Ethernet controllers but CFE bootloader uses only the first one. Fixes: 34322615cbaa ("net: bgmac: Mask interrupts during probe") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-07ionic: remove dead device fail pathShannon Nelson
Remove the probe error path code that leaves the driver bound to the device, but with essentially a dead device. This was useful maybe twice early in the driver's life and no longer makes sense to keep. Fixes: 30a1e6d0f8e2 ("ionic: keep ionic dev on lif init fail") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-07ionic: remove WARN_ON to prevent panic_on_warnNitya Sunkad
Remove unnecessary early code development check and the WARN_ON that it uses. The irq alloc and free paths have long been cleaned up and this check shouldn't have stuck around so long. Fixes: 77ceb68e29cc ("ionic: Add notifyq support") Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-07octeontx2-af: Move validation of ptp pointer before its usageSai Krishna
Moved PTP pointer validation before its use to avoid smatch warning. Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree. Fixes: 2ef4e45d99b1 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon") Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-07octeontx2-af: Promisc enable/disable through mboxRatheesh Kannoth
In legacy silicon, promiscuous mode is only modified through CGX mbox messages. In CN10KB silicon, it is modified from CGX mbox and NIX. This breaks legacy application behaviour. Fix this by removing call from NIX. Fixes: d6c9784baf59 ("octeontx2-af: Invoke exact match functions if supported") Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-07Merge branch '1GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2023-07-05 (igc) This series contains updates to igc driver only. Husaini adds check to increment Qbv change error counter only on taprio Qbvs. He also removes delay during Tx ring configuration and resolves Tx hang that could occur when transmitting on a gate to be closed. Prasad Koya reports ethtool link mode as TP (twisted pair). Tee Min corrects value for max SDU. Aravindhan ensures that registers for PPS are always programmed to occur in future. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-06gve: Set default duplex configuration to fullJunfeng Guo
Current duplex mode was unset in the driver, resulting in the default parameter being set to 0, which corresponds to half duplex. It might mislead users to have incorrect expectation about the driver's transmission capabilities. Set the default duplex configuration to full, as the driver runs in full duplex mode at this point. Fixes: 7e074d5a76ca ("gve: Enable Link Speed Reporting in the driver.") Signed-off-by: Junfeng Guo <junfeng.guo@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-06Merge branch '100GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2023-07-05 (ice) This series contains updates to ice driver only. Sridhar fixes incorrect comparison of max Tx rate limit to occur against each TC value rather than the aggregate. He also resolves an issue with the wrong VSI being used when setting max Tx rate when TCs are enabled. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix tx queue rate limit when TCs are configured ice: Fix max_rate check while configuring TX rate limits ==================== Link: https://lore.kernel.org/r/20230705201346.49370-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-06Merge tag 'mlx5-fixes-2023-07-05' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5 fixes 2023-07-05 This series provides bug fixes to mlx5 driver. * tag 'mlx5-fixes-2023-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: RX, Fix page_pool page fragment tracking for XDP net/mlx5: Query hca_cap_2 only when supported net/mlx5e: TC, CT: Offload ct clear only once net/mlx5e: Check for NOT_READY flag state after locking net/mlx5: Register a unique thermal zone per device net/mlx5e: RX, Fix flush and close release flow of regular rq for legacy rq net/mlx5e: fix memory leak in mlx5e_ptp_open net/mlx5e: fix memory leak in mlx5e_fs_tt_redirect_any_create net/mlx5e: fix double free in mlx5e_destroy_flow_table ==================== Link: https://lore.kernel.org/r/20230705175757.284614-1-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-06net: mscc: ocelot: fix oversize frame dropping for preemptible TCsVladimir Oltean
This switch implements Hold/Release in a strange way, with no control from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly based on the schedule. Namely, when the gate of a preemptible TC is about to close (actually QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event), the QSYS seems to emit a HOLD request pulse towards the MAC which preempts the currently transmitted packet, and further packets are held back in the queue system. This allows large frames to be squeezed through small time slots, because HOLD requests initiated by the gate events result in the frame being segmented in multiple fragments, the bit time of which is equal to the size of the time slot. It has been reported that the vsc9959_tas_guard_bands_update() logic breaks this, because it doesn't take preemptible TCs into account, and enables oversized frame dropping when the time slot doesn't allow a full MTU to be sent, but it does allow 2*minFragSize to be sent (128B). Packets larger than 128B are dropped instead of being sent in multiple fragments. Confusingly, the manual says: | For guard band, SDU calculation of a traffic class of a port, if | preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then | QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise | QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used. but this only refers to the static guard band durations, and the QMAXSDU_CFG_* registers have dual purpose - the other being oversized frame dropping, which takes place irrespective of whether frames are preemptible or express. So, to fix the problem, we need to call vsc9959_tas_guard_bands_update() from ocelot_port_update_active_preemptible_tcs(), and modify the guard band logic to consider a different (lower) oversize limit for preemptible traffic classes. Fixes: 403ffc2c34de ("net: mscc: ocelot: add support for preemptible traffic classes") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-06net: mscc: ocelot: extend ocelot->fwd_domain_lock to cover ocelot->tas_lockVladimir Oltean
In a future commit we will have to call vsc9959_tas_guard_bands_update() from ocelot_port_update_active_preemptible_tcs(), and that will be impossible due to the AB/BA locking dependencies between ocelot->tas_lock and ocelot->fwd_domain_lock. Just like we did in commit 3ff468ef987e ("net: mscc: ocelot: remove struct ocelot_mm_state :: lock"), the only solution is to expand the scope of ocelot->fwd_domain_lock for it to also serialize changes made to the Time-Aware Shaper, because those will have to result in a recalculation of cut-through TCs, which is something that depends on the forwarding domain. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-06net: mvneta: fix txq_map in case of txq_number==1Klaus Kudielka
If we boot with mvneta.txq_number=1, the txq_map is set incorrectly: MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is initialized. Fix this. Fixes: 50bf8cb6fc9c ("net: mvneta: Configure XPS support") Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-07-05Merge tag 'net-6.5-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net Pull networking fixes from Jakub Kicinski: "Including fixes from bluetooth, bpf and wireguard. Current release - regressions: - nvme-tcp: fix comma-related oops after sendpage changes Current release - new code bugs: - ptp: make max_phase_adjustment sysfs device attribute invisible when not supported Previous releases - regressions: - sctp: fix potential deadlock on &net->sctp.addr_wq_lock - mptcp: - ensure subflow is unhashed before cleaning the backlog - do not rely on implicit state check in mptcp_listen() Previous releases - always broken: - net: fix net_dev_start_xmit trace event vs skb_transport_offset() - Bluetooth: - fix use-bdaddr-property quirk - L2CAP: fix multiple UaFs - ISO: use hci_sync for setting CIG parameters - hci_event: fix Set CIG Parameters error status handling - hci_event: fix parsing of CIS Established Event - MGMT: fix marking SCAN_RSP as not connectable - wireguard: queuing: use saner cpu selection wrapping - sched: act_ipt: various bug fixes for iptables <> TC interactions - sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX - dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging - eth: sfc: fix null-deref in devlink port without MAE access - eth: ibmvnic: do not reset dql stats on NON_FATAL err Misc: - xsk: honor SO_BINDTODEVICE on bind" * tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits) nfp: clean mc addresses in application firmware when closing port selftests: mptcp: pm_nl_ctl: fix 32-bit support selftests: mptcp: depend on SYN_COOKIES selftests: mptcp: userspace_pm: report errors with 'remove' tests selftests: mptcp: userspace_pm: use correct server port selftests: mptcp: sockopt: return error if wrong mark selftests: mptcp: sockopt: use 'iptables-legacy' if available selftests: mptcp: connect: fail if nft supposed to work mptcp: do not rely on implicit state check in mptcp_listen() mptcp: ensure subflow is unhashed before cleaning the backlog s390/qeth: Fix vipa deletion octeontx-af: fix hardware timestamp configuration net: dsa: sja1105: always enable the send_meta options net: dsa: tag_sja1105: fix MAC DA patching from meta frames net: Replace strlcpy with strscpy pptp: Fix fib lookup calls. mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX xsk: Honor SO_BINDTODEVICE on bind ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported ...
2023-07-05igc: Handle PPS start time programming for past time valuesAravindhan Gunasekaran
I225/6 hardware can be programmed to start PPS output once the time in Target Time registers is reached. The time programmed in these registers should always be into future. Only then PPS output is triggered when SYSTIM register reaches the programmed value. There are two modes in i225/6 hardware to program PPS, pulse and clock mode. There were issues reported where PPS is not generated when start time is in past. Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period" In the current implementation, a value of '0' is programmed into Target time registers and PPS output is in pulse mode. Eventually an interrupt which is triggered upon SYSTIM register reaching Target time is not fired. Thus no PPS output is generated. Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period" Above case, a value of '0' is programmed into Target time registers and PPS output is in clock mode. Here, HW tries to catch-up the current time by incrementing Target Time register. This catch-up time seem to vary according to programmed PPS period time as per the HW design. In my experiments, the delay ranged between few tens of seconds to few minutes. The PPS output is only generated after the Target time register reaches current time. In my experiments, I also observed PPS stopped working with below test and could not recover until module is removed and loaded again. 1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period 2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period 3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period After this PPS did not work even if i re-program with proper values. I could only get this back working by reloading the driver. This patch takes care of calculating and programming appropriate future time value into Target Time registers. Fixes: 5e91c72e560c ("igc: Fix PPS delta between two synchronized end-points") Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com> Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05igc: Include the length/type field and VLAN tag in queueMaxSDUTan Tee Min
IEEE 802.1Q does not have clear definitions of what constitutes an SDU (Service Data Unit), but IEEE Std 802.3 clause 3.1.2 does define the MAC service primitives and clause 3.2.7 does define the MAC Client Data for Q-tagged frames. It shows that the mac_service_data_unit (MSDU) does NOT contain the preamble, destination and source address, or FCS. The MSDU does contain the length/type field, MAC client data, VLAN tag and any padding data (prior to the FCS). Thus, the maximum 802.3 frame size that is allowed to be transmitted should be QueueMaxSDU (MSDU) + 16 (6 byte SA + 6 byte DA + 4 byte FCS). Fixes: 92a0dcb8427d ("igc: offload queue max SDU from tc-taprio") Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05igc: set TP bit in 'supported' and 'advertising' fields of ↵Prasad Koya
ethtool_link_ksettings set TP bit in the 'supported' and 'advertising' fields. i225/226 parts only support twisted pair copper. Fixes: 8c5ad0dae93c ("igc: Add ethtool support") Signed-off-by: Prasad Koya <prasad@arista.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05nfp: clean mc addresses in application firmware when closing portYinjun Zhang
When moving devices from one namespace to another, mc addresses are cleaned in software while not removed from application firmware. Thus the mc addresses are remained and will cause resource leak. Now use `__dev_mc_unsync` to clean mc addresses when closing port. Fixes: e20aa071cd95 ("nfp: fix schedule in atomic context when sync mc address") Cc: stable@vger.kernel.org Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Acked-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Message-ID: <20230705052818.7122-1-louis.peens@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-07-05net/mlx5e: RX, Fix page_pool page fragment tracking for XDPDragos Tatulea
Currently mlx5e releases pages directly to the page_pool for XDP_TX and does page fragment counting for XDP_REDIRECT. RX pages from the page_pool are leaking on XDP_REDIRECT because the xdp core will release only one fragment out of MLX5E_PAGECNT_BIAS_MAX and subsequently the page is marked as "skip release" which avoids the driver release. A fix would be to take an extra fragment for XDP_REDIRECT and not set the "skip release" bit so that the release on the driver side can handle the remaining bias fragments. But this would be a shortsighted solution. Instead, this patch converges the two XDP paths (XDP_TX and XDP_REDIRECT) to always do fragment tracking. The "skip release" bit is no longer necessary for XDP. Fixes: 6f5742846053 ("net/mlx5e: RX, Enable skb page recycling through the page_pool") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5: Query hca_cap_2 only when supportedMaher Sanalla
On vport enable, where fw's hca caps are queried, the driver queries hca_caps_2 without checking if fw truly supports them, causing a false failure of vfs vport load and blocking SRIOV enablement on old devices such as CX4 where hca_caps_2 support is missing. Thus, add a check for the said caps support before accessing them. Fixes: e5b9642a33be ("net/mlx5: E-Switch, Implement devlink port function cmds to control migratable") Signed-off-by: Maher Sanalla <msanalla@nvidia.com> Reviewed-by: Shay Drory <shayd@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: TC, CT: Offload ct clear only onceYevgeny Kliteynik
Non-clear CT action causes a flow rule split, while CT clear action doesn't and is just a header-rewrite to the current flow rule. But ct offload is done in post_parse and is per ct action instance, so ct clear offload is parsed multiple times, while its deleted once. Fix this by post_parsing the ct action only once per flow attribute (which is per flow rule) by using a offloaded ct_attr flag. Fixes: 08fe94ec5f77 ("net/mlx5e: TC, Remove special handling of CT action") Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: Check for NOT_READY flag state after lockingVlad Buslov
Currently the check for NOT_READY flag is performed before obtaining the necessary lock. This opens a possibility for race condition when the flow is concurrently removed from unready_flows list by the workqueue task, which causes a double-removal from the list and a crash[0]. Fix the issue by moving the flag check inside the section protected by uplink_priv->unready_flows_lock mutex. [0]: [44376.389654] general protection fault, probably for non-canonical address 0xdead000000000108: 0000 [#1] SMP [44376.391665] CPU: 7 PID: 59123 Comm: tc Not tainted 6.4.0-rc4+ #1 [44376.392984] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [44376.395342] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core] [44376.396857] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06 [44376.399167] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246 [44376.399680] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00 [44376.400337] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0 [44376.401001] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001 [44376.401663] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000 [44376.402342] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000 [44376.402999] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000 [44376.403787] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [44376.404343] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0 [44376.405004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [44376.405665] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [44376.406339] Call Trace: [44376.406651] <TASK> [44376.406939] ? die_addr+0x33/0x90 [44376.407311] ? exc_general_protection+0x192/0x390 [44376.407795] ? asm_exc_general_protection+0x22/0x30 [44376.408292] ? mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core] [44376.408876] __mlx5e_tc_del_fdb_peer_flow+0xbc/0xe0 [mlx5_core] [44376.409482] mlx5e_tc_del_flow+0x42/0x210 [mlx5_core] [44376.410055] mlx5e_flow_put+0x25/0x50 [mlx5_core] [44376.410529] mlx5e_delete_flower+0x24b/0x350 [mlx5_core] [44376.411043] tc_setup_cb_reoffload+0x22/0x80 [44376.411462] fl_reoffload+0x261/0x2f0 [cls_flower] [44376.411907] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core] [44376.412481] ? mlx5e_rep_indr_setup_ft_cb+0x160/0x160 [mlx5_core] [44376.413044] tcf_block_playback_offloads+0x76/0x170 [44376.413497] tcf_block_unbind+0x7b/0xd0 [44376.413881] tcf_block_setup+0x17d/0x1c0 [44376.414269] tcf_block_offload_cmd.isra.0+0xf1/0x130 [44376.414725] tcf_block_offload_unbind+0x43/0x70 [44376.415153] __tcf_block_put+0x82/0x150 [44376.415532] ingress_destroy+0x22/0x30 [sch_ingress] [44376.415986] qdisc_destroy+0x3b/0xd0 [44376.416343] qdisc_graft+0x4d0/0x620 [44376.416706] tc_get_qdisc+0x1c9/0x3b0 [44376.417074] rtnetlink_rcv_msg+0x29c/0x390 [44376.419978] ? rep_movs_alternative+0x3a/0xa0 [44376.420399] ? rtnl_calcit.isra.0+0x120/0x120 [44376.420813] netlink_rcv_skb+0x54/0x100 [44376.421192] netlink_unicast+0x1f6/0x2c0 [44376.421573] netlink_sendmsg+0x232/0x4a0 [44376.421980] sock_sendmsg+0x38/0x60 [44376.422328] ____sys_sendmsg+0x1d0/0x1e0 [44376.422709] ? copy_msghdr_from_user+0x6d/0xa0 [44376.423127] ___sys_sendmsg+0x80/0xc0 [44376.423495] ? ___sys_recvmsg+0x8b/0xc0 [44376.423869] __sys_sendmsg+0x51/0x90 [44376.424226] do_syscall_64+0x3d/0x90 [44376.424587] entry_SYSCALL_64_after_hwframe+0x46/0xb0 [44376.425046] RIP: 0033:0x7f045134f887 [44376.425403] Code: 0a 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 89 54 24 1c 48 89 74 24 10 [44376.426914] RSP: 002b:00007ffd63a82b98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e [44376.427592] RAX: ffffffffffffffda RBX: 000000006481955f RCX: 00007f045134f887 [44376.428195] RDX: 0000000000000000 RSI: 00007ffd63a82c00 RDI: 0000000000000003 [44376.428796] RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000 [44376.429404] R10: 00007f0451208708 R11: 0000000000000246 R12: 0000000000000001 [44376.430039] R13: 0000000000409980 R14: 000000000047e538 R15: 0000000000485400 [44376.430644] </TASK> [44376.430907] Modules linked in: mlx5_ib mlx5_core act_mirred act_tunnel_key cls_flower vxlan dummy sch_ingress openvswitch nsh rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_g ss_krb5 auth_rpcgss oid_registry overlay zram zsmalloc fuse [last unloaded: mlx5_core] [44376.433936] ---[ end trace 0000000000000000 ]--- [44376.434373] RIP: 0010:mlx5e_tc_del_fdb_flow+0xb3/0x340 [mlx5_core] [44376.434951] Code: 00 48 8b b8 68 ce 02 00 e8 8a 4d 02 00 4c 8d a8 a8 01 00 00 4c 89 ef e8 8b 79 88 e1 48 8b 83 98 06 00 00 48 8b 93 90 06 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 83 90 06 [44376.436452] RSP: 0018:ffff88812cc97570 EFLAGS: 00010246 [44376.436924] RAX: dead000000000122 RBX: ffff8881088e3800 RCX: ffff8881881bac00 [44376.437530] RDX: dead000000000100 RSI: ffff88812cc97500 RDI: ffff8881242f71b0 [44376.438179] RBP: ffff88811cbb0940 R08: 0000000000000400 R09: 0000000000000001 [44376.438786] R10: 0000000000000001 R11: 0000000000000000 R12: ffff88812c944000 [44376.439393] R13: ffff8881242f71a8 R14: ffff8881222b4000 R15: 0000000000000000 [44376.439998] FS: 00007f0451104800(0000) GS:ffff88852cb80000(0000) knlGS:0000000000000000 [44376.440714] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [44376.441225] CR2: 0000000000489108 CR3: 0000000123a79003 CR4: 0000000000370ea0 [44376.441843] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [44376.442471] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: ad86755b18d5 ("net/mlx5e: Protect unready flows with dedicated lock") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5: Register a unique thermal zone per deviceSaeed Mahameed
Prior to this patch only one "mlx5" thermal zone could have been registered regardless of the number of individual mlx5 devices in the system. To fix this setup a unique name per device to register its own thermal zone. In order to not register a thermal zone for a virtual device (VF/SF) add a check for PF device type. The new name is a concatenation between "mlx5_" and "<PCI_DEV_BDF>", which will also help associating a thermal zone with its PCI device. $ lspci | grep ConnectX 00:04.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx] 00:05.0 Ethernet controller: Mellanox Technologies MT2892 Family [ConnectX-6 Dx] $ cat /sys/devices/virtual/thermal/thermal_zone0/type mlx5_0000:00:04.0 $ cat /sys/devices/virtual/thermal/thermal_zone1/type mlx5_0000:00:05.0 Fixes: c1fef618d611 ("net/mlx5: Implement thermal zone") CC: Sandipan Patra <spatra@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: RX, Fix flush and close release flow of regular rq for legacy rqDragos Tatulea
Regular (non-XSK) RQs get flushed on XSK setup and re-activated on XSK close. If the same regular RQ is closed (a config change for example) soon after the XSK close, a double release occurs because the missing wqes get released a second time. Fixes: 3f93f82988bc ("net/mlx5e: RX, Defer page release in legacy rq for better recycling") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: fix memory leak in mlx5e_ptp_openZhengchao Shao
When kvzalloc_node or kvzalloc failed in mlx5e_ptp_open, the memory pointed by "c" or "cparams" is not freed, which can lead to a memory leak. Fix by freeing the array in the error path. Fixes: 145e5637d941 ("net/mlx5e: Add TX PTP port object support") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: fix memory leak in mlx5e_fs_tt_redirect_any_createZhengchao Shao
The memory pointed to by the fs->any pointer is not freed in the error path of mlx5e_fs_tt_redirect_any_create, which can lead to a memory leak. Fix by freeing the memory in the error path, thereby making the error path identical to mlx5e_fs_tt_redirect_any_destroy(). Fixes: 0f575c20bf06 ("net/mlx5e: Introduce Flow Steering ANY API") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05net/mlx5e: fix double free in mlx5e_destroy_flow_tableZhengchao Shao
In function accel_fs_tcp_create_groups(), when the ft->g memory is successfully allocated but the 'in' memory fails to be allocated, the memory pointed to by ft->g is released once. And in function accel_fs_tcp_create_table, mlx5e_destroy_flow_table is called to release the memory pointed to by ft->g again. This will cause double free problem. Fixes: c062d52ac24c ("net/mlx5e: Receive flow steering framework for accelerated TCP flows") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-07-05igc: Fix TX Hang issue when QBV Gate is closedMuhammad Husaini Zulkifli
If a user schedules a Gate Control List (GCL) to close one of the QBV gates while also transmitting a packet to that closed gate, TX Hang will be happen. HW would not drop any packet when the gate is closed and keep queuing up in HW TX FIFO until the gate is re-opened. This patch implements the solution to drop the packet for the closed gate. This patch will also reset the adapter to perform SW initialization for each 1st Gate Control List (GCL) to avoid hang. This is due to the HW design, where changing to TSN transmit mode requires SW initialization. Intel Discrete I225/6 transmit mode cannot be changed when in dynamic mode according to Software User Manual Section 7.5.2.1. Subsequent Gate Control List (GCL) operations will proceed without a reset, as they already are in TSN Mode. Step to reproduce: DUT: 1) Configure GCL List with certain gate close. BASE=$(date +%s%N) tc qdisc replace dev $IFACE parent root handle 100 taprio \ num_tc 4 \ map 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 \ queues 1@0 1@1 1@2 1@3 \ base-time $BASE \ sched-entry S 0x8 500000 \ sched-entry S 0x4 500000 \ flags 0x2 2) Transmit the packet to closed gate. You may use udp_tai application to transmit UDP packet to any of the closed gate. ./udp_tai -i <interface> -P 100000 -p 90 -c 1 -t <0/1> -u 30004 Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading") Co-developed-by: Tan Tee Min <tee.min.tan@linux.intel.com> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Tested-by: Chwee Lin Choong <chwee.lin.choong@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05igc: Remove delay during TX ring configurationMuhammad Husaini Zulkifli
Remove unnecessary delay during the TX ring configuration. This will cause delay, especially during link down and link up activity. Furthermore, old SKUs like as I225 will call the reset_adapter to reset the controller during TSN mode Gate Control List (GCL) setting. This will add more time to the configuration of the real-time use case. It doesn't mentioned about this delay in the Software User Manual. It might have been ported from legacy code I210 in the past. Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings") Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05igc: Add condition for qbv_config_change_errors counterMuhammad Husaini Zulkifli
Add condition to increase the qbv counter during taprio qbv configuration only. There might be a case when TC already been setup then user configure the ETF/CBS qdisc and this counter will increase if no condition above. Fixes: ae4fe4698300 ("igc: Add qbv_config_change_errors counter") Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05ice: Fix tx queue rate limit when TCs are configuredSridhar Samudrala
Configuring tx_maxrate via sysfs interface /sys/class/net/eth0/queues/tx-1/tx_maxrate was not working when TCs are configured because always main VSI was being used. Fix by using correct VSI in ice_set_tx_maxrate when TCs are configured. Fixes: 1ddef455f4a8 ("ice: Add NDO callback to set the maximum per-queue bitrate") Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-05ice: Fix max_rate check while configuring TX rate limitsSridhar Samudrala
Remove incorrect check in ice_validate_mqprio_opt() that limits filter configuration when sum of max_rates of all TCs exceeds the link speed. The max rate of each TC is unrelated to value used by other TCs and is valid as long as it is less than link speed. Fixes: fbc7b27af0f9 ("ice: enable ndo_setup_tc support for mqprio_qdisc") Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2023-07-04octeontx-af: fix hardware timestamp configurationHariprasad Kelam
MAC block on CN10K (RPM) supports hardware timestamp configuration. The previous patch which added timestamp configuration support has a bug. Though the netdev driver requests to disable timestamp configuration, the driver is always enabling it. This patch fixes the same. Fixes: d1489208681d ("octeontx2-af: cn10k: RPM hardware timestamp configuration") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-04mlxsw: spectrum_router: Fix an IS_ERR() vs NULL checkDan Carpenter
The mlxsw_sp_crif_alloc() function returns NULL on error. It doesn't return error pointers. Fix the check. Fixes: 78126cfd5dc9 ("mlxsw: spectrum_router: Maintain CRIF for fallback loopback RIF") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-07-02octeontx2-af: Reset MAC features in FLRHariprasad Kelam
AF driver configures MAC features like internal loopback and PFC upon receiving the request from PF and its VF netdev. But these features are not getting reset in FLR. This patch fixes the issue by resetting the same. Fixes: 23999b30ae67 ("octeontx2-af: Enable or disable CGX internal loopback") Fixes: 1121f6b02e7a ("octeontx2-af: Priority flow control configuration support") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-07-28 09:26:15 +0000