| Age | Commit message (Collapse) | Author |
|---|
|
Finish initializing the adapter before registering netdev so state
is consistent.
Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we get a transport event, set the error and mark the init as
complete so the attempt to send crq-init or login fail sooner
rather than wait for the timeout.
Fixes: bbd669a868bb ("ibmvnic: Fix completion structure initialization")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define and use a helper to flush the reset queue.
Fixes: 2770a7984db5 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should initialize ->init_done_rc before calling complete(). Otherwise
the waiting thread may see ->init_done_rc as 0 before we have updated it
and may assume that the CRQ was successful.
Fixes: 6b278c0cb378 ("ibmvnic delay complete()")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a tiny memory leak when flushing the reset work queue.
Fixes: 2770a7984db5 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this driver's ->ndo_open() callback, it enables DMA interrupts,
starts the DMA channels, then requests interrupts with request_irq(),
and then finally enables napi.
If RX DMA interrupts are received before napi is enabled, no processing
is done because napi_schedule_prep() will return false. If the network
has a lot of broadcast/multicast traffic, then the RX ring could fill up
completely before napi is enabled. When this happens, no further RX
interrupts will be delivered, and the driver will fail to receive any
packets.
Fix this by only enabling DMA interrupts after all other initialization
is complete.
Fixes: 523f11b5d4fd72efb ("net: stmmac: move hardware setup for stmmac_open to new function")
Reported-by: Lars Persson <larper@axis.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.
It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.
Fixes: 76723bca2802 ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fi
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.
Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to configure TC map 0 for VSI 391
This reverts commit 3d2504663c41104b4359a15f35670cfa82de1bbf.
Fixes: 3d2504663c41 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VF min and max rate were passed incorrectly and resulted in wrongly
interchanging them. Fix the order of parameters in
mlx5_esw_qos_set_vport_rate().
Fixes: d7df09f5e7b4 ("net/mlx5: E-switch, Enable vport QoS on demand")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add mistakenly missing increment of count variable when looping over
output buffer in mlx5e_self_test().
This resolves the issue of garbage values output when querying with self
test via ethtool.
before:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 1768697188
Health Test 758528120
Loopback Test 3288687
after:
$ ethtool -t eth2
The test result is PASS
The test extra info:
Link Test 0
Speed Test 0
Health Test 0
Loopback Test 0
Fixes: 7990b1b5e8bd ("net/mlx5e: loopback test is not supported in switchdev mode")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently offload of rule on bareudp device require tunnel key
in order to match on mpls fields and without it the mpls fields
are ignored, this is incorrect due to the fact udp tunnel doesn't
have key to match on.
Fix by returning error in case flow is matching on tunnel key.
Fixes: 72046a91d134 ("net/mlx5e: Allow to match on mpls parameters")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently the MPLSoUDP encap builds the MPLS header using encap action
information (tunnel id, ttl and tos) instead of the MPLS action
information (label, ttl, tc and bos) which is wrong.
Fix by storing the MPLS action information during the flow action
parse and later using it to create the encap MPLS header.
Fixes: f828ca6a2fb6 ("net/mlx5e: Add support for hw encapsulation of MPLS over UDP")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Fec counters support is checked via the PCAM feature_cap_mask,
bit 0: PPCNT_counter_group_Phy_statistical_counter_group.
Add feature check to avoid faulty behavior.
Fixes: 0a1498ebfa55 ("net/mlx5e: Expose FEC counters via ethtool")
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Offload of ct clear action is just resetting the reg_c register.
It's done by allocating modify hdr resources which is limited.
Doing it multiple times is redundant and wasting modify hdr resources
and if resources depleted the driver will fail offloading the rule.
Ignore redundant ct clear actions after the first one.
Fixes: 806401c20a0f ("net/mlx5e: CT, Fix multiple allocations and memleak of mod acts")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Such rules are redundant but allowed and passed to the driver.
The driver does not support offloading such rules so return an error.
Fixes: 03a9d11e6eeb ("net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This kind of action is not supported by firmware and generates a
syndrome.
kernel: mlx5_core 0000:08:00.0: mlx5_cmd_check:777:(pid 102063): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x8708c3)
Fixes: d7e75a325cb2 ("net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Fixes: 1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The ioctl EEPROM query wrongly returns success on read failures, fix
that by returning the appropriate error code.
Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add missing call to up_write_ref_node() which releases the semaphore
in case the FTE doesn't have destinations, such in drop rule case.
Fixes: 465e7baab6d9 ("net/mlx5: Fix deletion of duplicate rules")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Only prio 1 is supported if firmware doesn't support ignore flow
level for nic mode. The offending commit removed the check wrongly.
Add it back.
Fixes: 9a99c8f1253a ("net/mlx5e: E-Switch, Offload all chain 0 priorities when modify header and forward action is not supported")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.
Fixes: 92ab1eb392c6 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, log_max_qp value is dependent on what FW reports as its max capability.
In reality, due to a bug, some FWs report a value greater than 17, even though they
don't support log_max_qp > 17.
This FW issue led the driver to exhaust memory on startup.
Thus, log_max_qp value is set to be no more than 17 regardless
of what FW reports, as it was before the cited commit.
Fixes: f79a609ea6bf ("net/mlx5: Update log_max_qp value to FW max capability")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Avihai Horon <avihaih@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When deciding whether to start syncing and actually free all the "hot"
ICM chunks, we need to consider the type of the ICM chunks that we're
dealing with. For instance, the amount of available ICM for MODIFY_ACTION
is significantly lower than the usual STE ICM, so the threshold should
account for that - otherwise we can deplete MODIFY_ACTION memory just by
creating and deleting the same modify header action in a continuous loop.
This patch replaces the hard-coded threshold with a dynamic value.
Fixes: 1c58651412bb ("net/mlx5: DR, ICM memory pools sync optimization")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently SMFS allows adding rule with matching on src/dst IP w/o matching
on full ethertype or ip_version, which is not supported by HW.
This patch fixes this issue and adds the check as it is done in DMFS.
Fixes: 26d688e33f88 ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When adding a rule with 32 destinations, we hit the following out-of-band
access issue:
BUG: KASAN: slab-out-of-bounds in mlx5_cmd_dr_create_fte+0x18ee/0x1e70
This patch fixes the issue by both increasing the allocated buffers to
accommodate for the needed actions and by checking the number of actions
to prevent this issue when a rule with too many actions is provided.
Fixes: 1ffd498901c1 ("net/mlx5: DR, Increase supported num of actions to 32")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
During rule insertion on each ICM memory chunk we also allocate shadow memory
used for management. This includes the hw_ste, dr_ste and miss list per entry.
Since the scale of these allocations is large we noticed a performance hiccup
that happens once malloc and free are stressed.
In extreme usecases when ~1M chunks are freed at once, it might take up to 40
seconds to complete this, up to the point the kernel sees this as self-detected
stall on CPU:
rcu: INFO: rcu_sched self-detected stall on CPU
To resolve this we will increase the reuse of shadow memory.
Doing this we see that a time in the aforementioned usecase dropped from ~40
seconds to ~8-10 seconds.
Fixes: 29cf8febd185 ("net/mlx5: DR, ICM pool memory allocator")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add the upcoming BlueField-4 and ConnectX-8 device IDs.
Fixes: 2e9d3e83ab82 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.
It is caused by below procedures in the driver:
1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule
After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.
Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
function call
This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If client is unable to initiate a failover reset via H_VIOCTL hcall, then
it should schedule a failover reset as a last resort. Otherwise, there is
no need to do a last resort.
Fixes: 334c42414729 ("ibmvnic: improve failover sysfs entry")
Reported-by: Cris Forno <cforno12@outlook.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221210545.115283-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To install a livepatch, first flash the package to NVM, and then
activate the patch through the "HWRM_FW_LIVEPATCH" fw command.
To uninstall a patch from NVM, flash the removal package and then
activate it through the "HWRM_FW_LIVEPATCH" fw command.
The "HWRM_FW_LIVEPATCH" fw command has to consider following scenarios:
1. no patch in NVM and no patch active. Do nothing.
2. patch in NVM, but not active. Activate the patch currently in NVM.
3. patch is not in NVM, but active. Deactivate the patch.
4. patch in NVM and the patch active. Do nothing.
Fix the code to handle these scenarios during devlink "fw_activate".
To install and activate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
To remove and deactivate a live patch:
devlink dev flash pci/0000:c1:00.0 file thor_patch_rem.pkg
devlink -f dev reload pci/0000:c1:00.0 action fw_activate limit no_reset
Fixes: 3c4153394e2c ("bnxt_en: implement firmware live patching")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db769c ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During ifdown, we call bnxt_inv_fw_health_reg() which will clear
both the status_reliable and resets_reliable flags if these
registers are mapped. This is correct because a FW reset during
ifdown will clear these register mappings. If we detect that FW
has gone through reset during the next ifup, we will remap these
registers.
But during normal ifup with no FW reset, we need to restore the
resets_reliable flag otherwise we will not show the reset counter
during devlink diagnose.
Fixes: 8cc95ceb7087 ("bnxt_en: improve fw diagnose devlink health messages")
Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should setup multicast only when net_device flags explicitly
has IFF_MULTICAST set. Otherwise we will incorrectly turn it on
even when not asked. Fix it by only passing the multicast table
to the firmware if IFF_MULTICAST is set.
Fixes: 7d2837dd7a32 ("bnxt_en: Setup multicast properly after resetting device.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b97a ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For offline (destructive) self tests, we need to stop the RDMA driver
first. Otherwise, the RDMA driver will run into unrecoverable errors
when destructive firmware tests are being performed.
The irq_re_init parameter used in the half close and half open
sequence when preparing the NIC for offline tests should be set to
true because the RDMA driver will free all IRQs before the offline
tests begin.
Fixes: 55fd0cf320c3 ("bnxt_en: Add external loopback test to ethtool selftest.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Ben Li <ben.li@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890ad8 ("bnxt_en: Report FEC settings to ethtool.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-02-18
This series contains updates to ice driver only.
Wojciech fixes protocol matching for slow-path switchdev so that all
packets are correctly redirected.
Michal removes accidental unconditional setting of l4 port filtering
flag.
Jake adds locking to protect VF reset and removal to fix various issues
that can be encountered when they race with each other.
Tom Rix propagates an error and initializes a struct to resolve reported
Clang issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ida_simple_get() returns an id between min (0) and max (NFP_MAX_MAC_INDEX)
inclusive.
So NFP_MAX_MAC_INDEX (0xff) is a valid id.
In order for the error handling path to work correctly, the 'invalid'
value for 'ida_idx' should not be in the 0..NFP_MAX_MAC_INDEX range,
inclusive.
So set it to -1.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220218131535.100258-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Booting a MACCHIATObin with 5.17, the system OOPs with
a null pointer deref when the network is started. This
is caused by the pcs->ops structure being null in
mcpp2_acpi_start() when it tries to call pcs_config().
Hoisting the code which sets pcs_gmac.ops and pcs_xlg.ops,
assuring they are always set, fixes the problem.
The OOPs looks like:
[ 18.687760] Unable to handle kernel access to user memory outside uaccess routines at virtual address 0000000000000010
[ 18.698561] Mem abort info:
[ 18.698564] ESR = 0x96000004
[ 18.698567] EC = 0x25: DABT (current EL), IL = 32 bits
[ 18.709821] SET = 0, FnV = 0
[ 18.714292] EA = 0, S1PTW = 0
[ 18.718833] FSC = 0x04: level 0 translation fault
[ 18.725126] Data abort info:
[ 18.729408] ISV = 0, ISS = 0x00000004
[ 18.734655] CM = 0, WnR = 0
[ 18.738933] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000111bbf000
[ 18.745409] [0000000000000010] pgd=0000000000000000, p4d=0000000000000000
[ 18.752235] Internal error: Oops: 96000004 [#1] SMP
[ 18.757134] Modules linked in: rfkill ip_set nf_tables nfnetlink qrtr sunrpc vfat fat omap_rng fuse zram xfs crct10dif_ce mvpp2 ghash_ce sbsa_gwdt phylink xhci_plat_hcd ahci_plam
[ 18.773481] CPU: 0 PID: 681 Comm: NetworkManager Not tainted 5.17.0-0.rc3.89.fc36.aarch64 #1
[ 18.781954] Hardware name: Marvell Armada 7k/8k Family Board /Armada 7k/8k Family Board , BIOS EDK II Jun 4 2019
[ 18.795222] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 18.802213] pc : mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[ 18.807208] lr : mvpp2_start_dev+0x298/0x300 [mvpp2]
[ 18.812197] sp : ffff80000b4732c0
[ 18.815522] x29: ffff80000b4732c0 x28: 0000000000000000 x27: ffffccab38ae57f8
[ 18.822689] x26: ffff6eeb03065a10 x25: ffff80000b473a30 x24: ffff80000b4735b8
[ 18.829855] x23: 0000000000000000 x22: 00000000000001e0 x21: ffff6eeb07b6ab68
[ 18.837021] x20: ffff6eeb07b6ab30 x19: ffff6eeb07b6a9c0 x18: 0000000000000014
[ 18.844187] x17: 00000000f6232bfe x16: ffffccab899b1dc0 x15: 000000006a30f9fa
[ 18.851353] x14: 000000003b77bd50 x13: 000006dc896f0e8e x12: 001bbbfccfd0d3a2
[ 18.858519] x11: 0000000000001528 x10: 0000000000001548 x9 : ffffccab38ad0fb0
[ 18.865685] x8 : ffff80000b473330 x7 : 0000000000000000 x6 : 0000000000000000
[ 18.872851] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff80000b4732f8
[ 18.880017] x2 : 000000000000001a x1 : 0000000000000002 x0 : ffff6eeb07b6ab68
[ 18.887183] Call trace:
[ 18.889637] mvpp2_start_dev+0x2b0/0x300 [mvpp2]
[ 18.894279] mvpp2_open+0x134/0x2b4 [mvpp2]
[ 18.898483] __dev_open+0x128/0x1e4
[ 18.901988] __dev_change_flags+0x17c/0x1d0
[ 18.906187] dev_change_flags+0x30/0x70
[ 18.910038] do_setlink+0x278/0xa7c
[ 18.913540] __rtnl_newlink+0x44c/0x7d0
[ 18.917391] rtnl_newlink+0x5c/0x8c
[ 18.920892] rtnetlink_rcv_msg+0x254/0x314
[ 18.925006] netlink_rcv_skb+0x48/0x10c
[ 18.928858] rtnetlink_rcv+0x24/0x30
[ 18.932449] netlink_unicast+0x290/0x2f4
[ 18.936386] netlink_sendmsg+0x1d0/0x41c
[ 18.940323] sock_sendmsg+0x60/0x70
[ 18.943825] ____sys_sendmsg+0x248/0x260
[ 18.947762] ___sys_sendmsg+0x74/0xa0
[ 18.951438] __sys_sendmsg+0x64/0xcc
[ 18.955027] __arm64_sys_sendmsg+0x30/0x40
[ 18.959140] invoke_syscall+0x50/0x120
[ 18.962906] el0_svc_common.constprop.0+0x4c/0xf4
[ 18.967629] do_el0_svc+0x30/0x9c
[ 18.970958] el0_svc+0x28/0xb0
[ 18.974025] el0t_64_sync_handler+0x10c/0x140
[ 18.978400] el0t_64_sync+0x1a4/0x1a8
[ 18.982078] Code: 52800004 b9416262 aa1503e0 52800041 (f94008a5)
[ 18.988196] ---[ end trace 0000000000000000 ]---
Fixes: cff056322372 ("net: mvpp2: use .mac_select_pcs() interface")
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220214231852.3331430-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang static analysis reports this issues
ice_common.c:5008:21: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ldo->phy_type_low |= ((u64)buf << (i * 16));
~~~~~~~~~~~~~~~~~ ^
When called from ice_cfg_phy_fec() ldo is the uninitialized local
variable tlv. So initialize.
Fixes: ea78ce4dab05 ("ice: add link lenient and default override support")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Clang static analysis reports this issue
time64.h:69:50: warning: The left operand of '+'
is a garbage value
set_normalized_timespec64(&ts_delta, lhs.tv_sec + rhs.tv_sec,
~~~~~~~~~~ ^
In ice_ptp_adjtime_nonatomic(), the timespec64 variable 'now'
is set by ice_ptp_gettimex64(). This function can fail
with -EBUSY, so 'now' can have a gargbage value.
So check the return.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit c503e63200c6 ("ice: Stop processing VF messages during teardown")
introduced a driver state flag, ICE_VF_DEINIT_IN_PROGRESS, which is
intended to prevent some issues with concurrently handling messages from
VFs while tearing down the VFs.
This change was motivated by crashes caused while tearing down and
bringing up VFs in rapid succession.
It turns out that the fix actually introduces issues with the VF driver
caused because the PF no longer responds to any messages sent by the VF
during its .remove routine. This results in the VF potentially removing
its DMA memory before the PF has shut down the device queues.
Additionally, the fix doesn't actually resolve concurrency issues within
the ice driver. It is possible for a VF to initiate a reset just prior
to the ice driver removing VFs. This can result in the remove task
concurrently operating while the VF is being reset. This results in
similar memory corruption and panics purportedly fixed by that commit.
Fix this concurrency at its root by protecting both the reset and
removal flows using the existing VF cfg_lock. This ensures that we
cannot remove the VF while any outstanding critical tasks such as a
virtchnl message or a reset are occurring.
This locking change also fixes the root cause originally fixed by commit
c503e63200c6 ("ice: Stop processing VF messages during teardown"), so we
can simply revert it.
Note that I kept these two changes together because simply reverting the
original commit alone would leave the driver vulnerable to worse race
conditions.
Fixes: c503e63200c6 ("ice: Stop processing VF messages during teardown")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Accidentally filter flag for none encapsulated l4 port field is always
set. Even if user wants to add encapsulated l4 port field.
Remove this unnecessary flag setting.
Fixes: 9e300987d4a81 ("ice: VXLAN and Geneve TC support")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In switchdev mode, slow-path rules need to match all protocols, in order
to correctly redirect unfiltered or missed packets to the uplink. To set
this up for the virtual function to uplink flow, the rule that redirects
packets to the control VSI must have the tunnel type set to
ICE_SW_TUN_AND_NON_TUN. As a result of that new tunnel type being set,
ice_get_compat_fv_bitmap will select ICE_PROF_ALL. At that point all
profiles would be selected for this rule, resulting in the desired
behavior. Without this change slow-path would not work with
tunnel protocols.
Fixes: 8b032a55c1bd ("ice: low level support for tunnels")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f051 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 GRE tunnels are not being offloaded, this is caused by a missing
netdev offload check. The functionality of IPv6 GRE tunnel offloading
was previously added but this check was not included. Adding the
ip6gretap check allows IPv6 GRE tunnels to be offloaded correctly.
Fixes: f7536ffb0986 ("nfp: flower: Allow ipv6gretap interface for offloading")
Signed-off-by: Danie du Toit <danie.dutoit@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220217124820.40436-1-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 3710e80952cf2dc48257ac9f145b117b5f74e0a5.
Since idm_base and nicpm_base are still optional resources not present
on all platforms, this breaks the driver for everything except Northstar
2 (which has both).
The same change was already reverted once with 755f5738ff98 ("net:
broadcom: fix a mistake about ioremap resource").
So let's do it again.
Fixes: 3710e80952cf ("net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[florian: Added comments to explain the resources are optional]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220216184634.2032460-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
