| Age | Commit message (Collapse) | Author |
|---|
|
The ice_sq_done function is used to check the control queue head register
and determine whether or not the control queue processing is done. This
function is called in a loop checking against jiffies for a specified
timeout.
The pattern of reading a register in a loop until a condition is true or a
timeout is reached is a relatively common pattern. In fact, the kernel
provides a read_poll_timeout function implementing this behavior in
<linux/iopoll.h>
Use of read_poll_timeout is preferred over directly coding these loops.
However, using it in the ice driver is a bit more difficult because of the
rd32 wrapper. Implement a rd32_poll_timeout wrapper based on
read_poll_timeout.
Refactor ice_sq_done to use rd32_poll_timeout, replacing the loop calling
ice_sq_done in ice_sq_send_cmd. This simplifies the logic down to a single
ice_sq_done() call.
The implementation of rd32_poll_timeout uses microseconds for its timeout
value, so update the CQ timeout macros used to be specified in microseconds
units as well instead of using HZ for jiffies.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.h
c948c0973df5 ("bnxt_en: Don't clear ntuple filters and rss contexts during ethtool ops")
f2878cdeb754 ("bnxt_en: Add support to call FW to update a VNIC")
Link: https://patch.msgid.link/20240822210125.1542769-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds with GCC 14.2.0 warn that:
.../aq_ethtool.c:278:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 6 [-Wformat-truncation=]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~
.../aq_ethtool.c:278:56: note: directive argument in the range [-2147483641, 254]
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~
.../aq_ethtool.c:278:33: note: ‘snprintf’ output between 5 and 15 bytes into a destination of size 8
278 | snprintf(tc_string, 8, "TC%d ", tc);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tc is always in the range 0 - cfg->tcs. And as cfg->tcs is a u8,
the range is 0 - 255. Further, on inspecting the code, it seems
that cfg->tcs will never be more than AQ_CFG_TCS_MAX (8), so
the range is actually 0 - 8.
So, it seems that the condition that GCC flags will not occur.
But, nonetheless, it would be nice if it didn't emit the warning.
It seems that this can be achieved by changing the format specifier
from %d to %u, in which case I believe GCC recognises an upper bound
on the range of tc of 0 - 255. After some experimentation I think
this is due to the combination of the use of %u and the type of
cfg->tcs (u8).
Empirically, updating the type of the tc variable to unsigned int
has the same effect.
As both of these changes seem to make sense in relation to what the code
is actually doing - iterating over unsigned values - do both.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821-atlantic-str-v1-1-fa2cfe38ca00@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a multicast address is removed but there are still some multicast
addresses, that address would remain programmed into the frame filter.
Fix this by explicitly setting the enable bit for each filter.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If promiscuous mode is disabled when there are fewer than four multicast
addresses, then it will not be reflected in the hardware. Fix this by
always clearing the promiscuous mode flag even when we program multicast
addresses.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Let the kememdup_array() take care about multiplication and possible
overflows.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821081447.12430-1-yujiaoliang@vivo.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GDM1 port on EN7581 SoC is connected to the lan dsa switch.
GDM{2,3,4} can be used as wan port connected to an external
phy module. Configure hw mac address registers according to the port id.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20240821-airoha-eth-wan-mac-addr-v2-1-8706d0cd6cd5@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Some CPT AF registers are per LF and others are global. Translation
of PF/VF local LF slot number to actual LF slot number is required
only for accessing perf LF registers. CPT AF global registers access
do not require any LF slot number. Also, there is no reason CPT
PF/VF to know actual lf's register offset.
Without this fix microcode loading will fail, VFs cannot be created
and hardware is not usable.
Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write")
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The MAC only has add the TX delay and it can not be modified.
MAC and PHY are both set the TX delay cause transmission problems.
So just disable TX delay in PHY, when use rgmii to attach to
external phy, set PHY_INTERFACE_MODE_RGMII_RXID to phy drivers.
And it is does not matter to internal phy.
Fixes: bc2426d74aa3 ("net: ngbe: convert phylib to phylink")
Signed-off-by: Mengyuan Lou <mengyuanlou@net-swift.com>
Cc: stable@vger.kernel.org # 6.3+
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/E6759CF1387CF84C+20240820030425.93003-1-mengyuanlou@net-swift.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-20 (ice)
This series contains updates to ice driver only.
Maciej fixes issues with Rx data path on architectures with
PAGE_SIZE >= 8192; correcting page reuse usage and calculations for
last offset and truesize.
Michal corrects assignment of devlink port number to use PF id.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: use internal pf id instead of function number
ice: fix truesize operations for PAGE_SIZE >= 8192
ice: fix ICE_LAST_OFFSET formula
ice: fix page reuse when PAGE_SIZE is over 8k
====================
Link: https://patch.msgid.link/20240820215620.1245310-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reading the statistics counters, if they are enabled.
The counters may be 64-bit, but we can't detect this statically as
there's no ability bit for it and the counters are read-only. Therefore,
we assume the counters are 32-bits by default. To ensure we don't miss
an overflow, we read all counters at 13-second intervals. This should be
often enough to ensure the bytes counters don't wrap at 2.5 Gbit/s.
Another complication is that the counters may be reset when the device
is reset (depending on configuration). To ensure the counters persist
across link up/down (including suspend/resume), we maintain our own
versions along with the last counter value we saw. Because we might wait
up to 100 ms for the reset to complete, we use a mutex to protect
writing hw_stats. We can't sleep in ndo_get_stats64, so we use a seqlock
to protect readers.
We don't bother disabling the refresh work when we detect 64-bit
counters. This is because the reset issue requires us to read
hw_stat_base and reset_in_progress anyway, which would still require the
seqcount. And I don't think skipping the task is worth the extra
bookkeeping.
We can't use the byte counters for either get_stats64 or
get_eth_mac_stats. This is because the byte counters include everything
in the frame (destination address to FCS, inclusive). But
rtnl_link_stats64 wants bytes excluding the FCS, and
ethtool_eth_mac_stats wants to exclude the L2 overhead (addresses and
length/type). It might be possible to calculate the byte values Linux
expects based on the frame counters, but I think it is simpler to use
the existing software counters.
get_ethtool_stats is implemented for nonstandard statistics. This
includes the aforementioned byte counters, VLAN and PFC frame
counters, and user-defined (e.g. with custom RTL) counters.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20240820175343.760389-3-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Receive Frame Rejected interrupt is asserted whenever there was a
receive error (bad FCS, bad length, etc.) or whenever the frame was
dropped due to a mismatched address. So this is really a combination of
rx_otherhost_dropped, rx_length_errors, rx_frame_errors, and
rx_crc_errors. Mismatched addresses are common and aren't really errors
at all (much like how fragments are normal on half-duplex links). To
avoid confusion, report these events as rx_dropped. This better
reflects what's going on: the packet was received by the MAC but dropped
before being processed.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://patch.msgid.link/20240820175343.760389-2-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove the dma_unmap_page_attrs() call in the driver's XDP_REDIRECT
code path. This should have been removed when we let the page pool
handle the DMA mapping. This bug causes the warning:
WARNING: CPU: 7 PID: 59 at drivers/iommu/dma-iommu.c:1198 iommu_dma_unmap_page+0xd5/0x100
CPU: 7 PID: 59 Comm: ksoftirqd/7 Tainted: G W 6.8.0-1010-gcp #11-Ubuntu
Hardware name: Dell Inc. PowerEdge R7525/0PYVT1, BIOS 2.15.2 04/02/2024
RIP: 0010:iommu_dma_unmap_page+0xd5/0x100
Code: 89 ee 48 89 df e8 cb f2 69 ff 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9 31 f6 31 ff 45 31 c0 e9 ab 17 71 00 <0f> 0b 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d 31 c0 31 d2 31 c9
RSP: 0018:ffffab1fc0597a48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99ff838280c8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffffab1fc0597a78 R08: 0000000000000002 R09: ffffab1fc0597c1c
R10: ffffab1fc0597cd3 R11: ffff99ffe375acd8 R12: 00000000e65b9000
R13: 0000000000000050 R14: 0000000000001000 R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffff9a06efb80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000565c34c37210 CR3: 00000005c7e3e000 CR4: 0000000000350ef0
? show_regs+0x6d/0x80
? __warn+0x89/0x150
? iommu_dma_unmap_page+0xd5/0x100
? report_bug+0x16a/0x190
? handle_bug+0x51/0xa0
? exc_invalid_op+0x18/0x80
? iommu_dma_unmap_page+0xd5/0x100
? iommu_dma_unmap_page+0x35/0x100
dma_unmap_page_attrs+0x55/0x220
? bpf_prog_4d7e87c0d30db711_xdp_dispatcher+0x64/0x9f
bnxt_rx_xdp+0x237/0x520 [bnxt_en]
bnxt_rx_pkt+0x640/0xdd0 [bnxt_en]
__bnxt_poll_work+0x1a1/0x3d0 [bnxt_en]
bnxt_poll+0xaa/0x1e0 [bnxt_en]
__napi_poll+0x33/0x1e0
net_rx_action+0x18a/0x2f0
Fixes: 578fcfd26e2a ("bnxt_en: Let the page pool manage the DMA mapping")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240820203415.168178-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BIT() is unsigned long but ->pu.flg_msk and ->pu.flg_val are u64 type.
On 32 bit systems, unsigned long is a u32 and the mismatch between u32
and u64 will break things for the high 32 bits.
Fixes: 9a4c07aaa0f5 ("ice: add parser execution main loop")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://patch.msgid.link/ddc231a8-89c1-4ff4-8704-9198bcb41f8d@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sabrina reports that the igb driver does not cope well with large
MAX_SKB_FRAG values: setting MAX_SKB_FRAG to 45 causes payload
corruption on TX.
An easy reproducer is to run ssh to connect to the machine. With
MAX_SKB_FRAGS=17 it works, with MAX_SKB_FRAGS=45 it fails. This has
been reported originally in
https://bugzilla.redhat.com/show_bug.cgi?id=2265320
The root cause of the issue is that the driver does not take into
account properly the (possibly large) shared info size when selecting
the ring layout, and will try to fit two packets inside the same 4K
page even when the 1st fraglist will trump over the 2nd head.
Address the issue by checking if 2K buffers are insufficient.
Fixes: 3948b05950fd ("net: introduce a config option to tweak MAX_SKB_FRAGS")
Reported-by: Jan Tluka <jtluka@redhat.com>
Reported-by: Jirka Hladky <jhladky@redhat.com>
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Link: https://patch.msgid.link/20240816152034.1453285-1-vinschen@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It is done everywhere in cxgb4 code, e.g. in is_filter_exact_match()
There is no reason it should not be done here
Found by Linux Verification Center (linuxtesting.org) with SVACE
Signed-off-by: Nikolay Kuratov <kniv@yandex-team.ru>
Cc: stable@vger.kernel.org
Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters")
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240819075408.92378-1-kniv@yandex-team.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a helper function ARRAY_SIZE() to help calculating the
u32 array size, and we don't need to do it mannually. So, let's
use ARRAY_SIZE() to calculate the array size, and improve the code
readability.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Jijie Shao<shaojijie@huawei.com>
Link: https://patch.msgid.link/20240818052518.45489-1-zhangzekun11@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dpaa2_switch_add_bufs() function returns the number of bufs that it
was able to add. It returns BUFS_PER_CMD (7) for complete success or a
smaller number if there are not enough pages available. However, the
error checking is looking at the total number of bufs instead of the
number which were added on this iteration. Thus the error checking
only works correctly for the first iteration through the loop and
subsequent iterations are always counted as a success.
Fix this by checking only the bufs added in the current iteration.
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://patch.msgid.link/eec27f30-b43f-42b6-b8ee-04a6f83423b6@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use always the same pf id in devlink port number. When doing
pass-through the PF to VM bus info func number can be any value.
Fixes: 2ae0aa4758b0 ("ice: Move devlink port to PF/VF struct")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When working on multi-buffer packet on arch that has PAGE_SIZE >= 8192,
truesize is calculated and stored in xdp_buff::frame_sz per each
processed Rx buffer. This means that frame_sz will contain the truesize
based on last received buffer, but commit 1dc1a7e7f410 ("ice:
Centrallize Rx buffer recycling") assumed this value will be constant
for each buffer, which breaks the page recycling scheme and mess up the
way we update the page::page_offset.
To fix this, let us work on constant truesize when PAGE_SIZE >= 8192
instead of basing this on size of a packet read from Rx descriptor. This
way we can simplify the code and avoid calculating truesize per each
received frame and on top of that when using
xdp_update_skb_shared_info(), current formula for truesize update will
be valid.
This means ice_rx_frame_truesize() can be removed altogether.
Furthermore, first call to it within ice_clean_rx_irq() for 4k PAGE_SIZE
was redundant as xdp_buff::frame_sz is initialized via xdp_init_buff()
in ice_vsi_cfg_rxq(). This should have been removed at the point where
xdp_buff struct started to be a member of ice_rx_ring and it was no
longer a stack based variable.
There are two fixes tags as my understanding is that the first one
exposed us to broken truesize and page_offset handling and then second
introduced broken skb_shared_info update in ice_{construct,build}_skb().
Reported-and-tested-by: Luiz Capitulino <luizcap@redhat.com>
Closes: https://lore.kernel.org/netdev/8f9e2a5c-fd30-4206-9311-946a06d031bb@redhat.com/
Fixes: 1dc1a7e7f410 ("ice: Centrallize Rx buffer recycling")
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
For bigger PAGE_SIZE archs, ice driver works on 3k Rx buffers.
Therefore, ICE_LAST_OFFSET should take into account ICE_RXBUF_3072, not
ICE_RXBUF_2048.
Fixes: 7237f5b0dba4 ("ice: introduce legacy Rx flag")
Suggested-by: Luiz Capitulino <luizcap@redhat.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Architectures that have PAGE_SIZE >= 8192 such as arm64 should act the
same as x86 currently, meaning reuse of a page should only take place
when no one else is busy with it.
Do two things independently of underlying PAGE_SIZE:
- store the page count under ice_rx_buf::pgcnt
- then act upon its value vs ice_rx_buf::pagecnt_bias when making the
decision regarding page reuse
Fixes: 2b245cb29421 ("ice: Implement transmit and NAPI support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
for_each_child_of_node can help to iterate through the device_node,
and we don't need to use while loop. No functional change with this
conversion.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240816015837.109627-1-zhangzekun11@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These are never implenmented since commit b691b1116e82 ("net/mlx5: Implement
devlink port function cmds to control ipsec_packet").
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240816101550.881844-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no caller and implementations in tree.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240816101638.882072-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit f13697cc7a19 ("gve: Switch to config-aware queue allocation")
convert this function to gve_rx_alloc_rings_gqi().
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240816101906.882743-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In bnx2x_get_vf_config():
* The vlan field of ivi is a 32-bit integer, it is used to store a vlan ID.
* The vlan field of bulletin is a 16-bit integer, it is also used to store
a vlan ID.
In the current code, ivi->vlan is set using memset. But in the case of
setting it to the value of bulletin->vlan, this involves reading
32 bits from a 16bit source. This is likely safe, as the following
6 bytes are padding in the same structure, but none the less, it seems
undesirable.
However, it is entirely unclear to me how this scheme works on
big-endian systems.
Resolve this by simply assigning integer values to ivi->vlan.
Flagged by W=1 builds.
f.e. gcc-14 reports:
In function 'fortify_memcpy_chk',
inlined from 'bnx2x_get_vf_config' at .../bnx2x_sriov.c:2655:4:
.../fortify-string.h:580:25: warning: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Wattribute-warning]
580 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20240815-bnx2x-int-vlan-v1-1-5940b76e37ad@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove unnecessary NULL check before freeing using kvfree().
This function will ignore a NULL argument.
Flagged by Coccinelle:
.../txgbe_hw.c:187:2-8: WARNING: NULL check before some freeing functions is not needed.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240815-txgbe-kvfree-v1-1-5ecf8656f555@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove a variable that has never been used.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://patch.msgid.link/20240815074956.155224-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prevent the call trace below from happening, by not allowing IPsec
creation over a slave, if master device doesn't support IPsec.
WARNING: CPU: 44 PID: 16136 at kernel/locking/rwsem.c:240 down_read+0x75/0x94
Modules linked in: esp4_offload esp4 act_mirred act_vlan cls_flower sch_ingress mlx5_vdpa vringh vhost_iotlb vdpa mst_pciconf(OE) nfsv3 nfs_acl nfs lockd grace fscache netfs xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 rfkill cuse fuse rpcrdma sunrpc rdma_ucm ib_srpt ib_isert iscsi_target_mod target_core_mod ib_umad ib_iser libiscsi scsi_transport_iscsi rdma_cm ib_ipoib iw_cm ib_cm ipmi_ssif intel_rapl_msr intel_rapl_common amd64_edac edac_mce_amd kvm_amd kvm irqbypass crct10dif_pclmul crc32_pclmul mlx5_ib ghash_clmulni_intel sha1_ssse3 dell_smbios ib_uverbs aesni_intel crypto_simd dcdbas wmi_bmof dell_wmi_descriptor cryptd pcspkr ib_core acpi_ipmi sp5100_tco ccp i2c_piix4 ipmi_si ptdma k10temp ipmi_devintf ipmi_msghandler acpi_power_meter acpi_cpufreq ext4 mbcache jbd2 sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect mlx5_core sysimgblt fb_sys_fops cec
ahci libahci mlxfw drm pci_hyperv_intf libata tg3 sha256_ssse3 tls megaraid_sas i2c_algo_bit psample wmi dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mst_pci]
CPU: 44 PID: 16136 Comm: kworker/44:3 Kdump: loaded Tainted: GOE 5.15.0-20240509.el8uek.uek7_u3_update_v6.6_ipsec_bf.x86_64 #2
Hardware name: Dell Inc. PowerEdge R7525/074H08, BIOS 2.0.3 01/15/2021
Workqueue: events xfrm_state_gc_task
RIP: 0010:down_read+0x75/0x94
Code: 00 48 8b 45 08 65 48 8b 14 25 80 fc 01 00 83 e0 02 48 09 d0 48 83 c8 01 48 89 45 08 5d 31 c0 89 c2 89 c6 89 c7 e9 cb 88 3b 00 <0f> 0b 48 8b 45 08 a8 01 74 b2 a8 02 75 ae 48 89 c2 48 83 ca 02 f0
RSP: 0018:ffffb26387773da8 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffa08b658af900 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ff886bc5e1366f2f RDI: 0000000000000000
RBP: ffffa08b658af940 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffa0a9bfb31540
R13: ffffa0a9bfb37900 R14: 0000000000000000 R15: ffffa0a9bfb37905
FS: 0000000000000000(0000) GS:ffffa0a9bfb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055a45ed814e8 CR3: 000000109038a000 CR4: 0000000000350ee0
Call Trace:
<TASK>
? show_trace_log_lvl+0x1d6/0x2f9
? show_trace_log_lvl+0x1d6/0x2f9
? mlx5_devcom_for_each_peer_begin+0x29/0x60 [mlx5_core]
? down_read+0x75/0x94
? __warn+0x80/0x113
? down_read+0x75/0x94
? report_bug+0xa4/0x11d
? handle_bug+0x35/0x8b
? exc_invalid_op+0x14/0x75
? asm_exc_invalid_op+0x16/0x1b
? down_read+0x75/0x94
? down_read+0xe/0x94
mlx5_devcom_for_each_peer_begin+0x29/0x60 [mlx5_core]
mlx5_ipsec_fs_roce_tx_destroy+0xb1/0x130 [mlx5_core]
tx_destroy+0x1b/0xc0 [mlx5_core]
tx_ft_put+0x53/0xc0 [mlx5_core]
mlx5e_xfrm_free_state+0x45/0x90 [mlx5_core]
___xfrm_state_destroy+0x10f/0x1a2
xfrm_state_gc_task+0x81/0xa9
process_one_work+0x1f1/0x3c6
worker_thread+0x53/0x3e4
? process_one_work.cold+0x46/0x3c
kthread+0x127/0x144
? set_kthread_struct+0x60/0x52
ret_from_fork+0x22/0x2d
</TASK>
---[ end trace 5ef7896144d398e1 ]---
Fixes: dfbd229abeee ("net/mlx5: Configure IPsec steering for egress RoCEv2 MPV traffic")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240815071611.2211873-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The offending commit overlooked the Multi-PF Netdev changes.
Revert mlx5e_set_default_xps_cpumasks to incorporate Multi-PF Netdev
changes.
Fixes: bcee093751f8 ("net/mlx5e: Modifying channels number and updating TX queues")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240815071611.2211873-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The change in the fixes tag cleaned up too much: it removed the part
that was releasing header pages that were posted via UMR but haven't
been acknowledged yet on the ICOSQ.
This patch corrects this omission by setting the bits between pi and ci
to on when shutting down a queue with SHAMPO. To be consistent with the
Striding RQ code, this action is done in mlx5e_free_rx_missing_descs().
Fixes: e839ac9a89cb ("net/mlx5e: SHAMPO, Simplify header page release in teardown")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240815071611.2211873-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When SHAMPO is used, a receive queue currently almost always leaks one
page on shutdown.
A page has MLX5E_SHAMPO_WQ_HEADER_PER_PAGE (8) headers. These headers
are tracked in the SHAMPO bitmap. Each page is released when the last
header index in the group is processed. During header allocation, there
can be leftovers from a page that will be used in a subsequent
allocation. This is normally fine, except for the following scenario
(simplified a bit):
1) Allocate N new page fragments, showing only the relevant last 4
fragments:
0: new page
1: new page
2: new page
3: new page
4: page from previous allocation
5: page from previous allocation
6: page from previous allocation
7: page from previous allocation
2) NAPI processes header indices 4-7 because they are the oldest
allocated. Bit 7 will be set to 0.
3) Receive queue shutdown occurs. All the remaining bits are being
iterated on to release the pages. But the page assigned to header
indices 0-3 will not be freed due to what happened in step 2.
This patch fixes the issue by making sure that on allocation, header
fragments are always allocated in groups of
MLX5E_SHAMPO_WQ_HEADER_PER_PAGE so that there is never a partial page
left over between allocations.
A more appropriate fix would be a refactoring of
mlx5e_alloc_rx_hd_mpwqe() and mlx5e_build_shampo_hd_umr(). But this
refactoring is too big for net. It will be targeted for net-next.
Fixes: e839ac9a89cb ("net/mlx5e: SHAMPO, Simplify header page release in teardown")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240815071611.2211873-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
ice: iavf: add support for TC U32 filters on VFs
Ahmed Zaki says:
The Intel Ethernet 800 Series is designed with a pipeline that has
an on-chip programmable capability called Dynamic Device Personalization
(DDP). A DDP package is loaded by the driver during probe time. The DDP
package programs functionality in both the parser and switching blocks in
the pipeline, allowing dynamic support for new and existing protocols.
Once the pipeline is configured, the driver can identify the protocol and
apply any HW action in different stages, for example, direct packets to
desired hardware queues (flow director), queue groups or drop.
Patches 1-8 introduce a DDP package parser API that enables different
pipeline stages in the driver to learn the HW parser capabilities from
the DDP package that is downloaded to HW. The parser library takes raw
packet patterns and masks (in binary) indicating the packet protocol fields
to be matched and generates the final HW profiles that can be applied at
the required stage. With this API, raw flow filtering for FDIR or RSS
could be done on new protocols or headers without any driver or Kernel
updates (only need to update the DDP package). These patches were submitted
before [1] but were not accepted mainly due to lack of a user.
Patches 9-11 extend the virtchnl support to allow the VF to request raw
flow director filters. Upon receiving the raw FDIR filter request, the PF
driver allocates and runs a parser lib instance and generates the hardware
profile definitions required to program the FDIR stage. These were also
submitted before [2].
Finally, patches 12 and 13 add TC U32 filter support to the iavf driver.
Using the parser API, the ice driver runs the raw patterns sent by the
user and then adds a new profile to the FDIR stage associated with the VF's
VSI. Refer to examples in patch 13 commit message.
[1]: https://lore.kernel.org/netdev/20230904021455.3944605-1-junfeng.guo@intel.com/
[2]: https://lore.kernel.org/intel-wired-lan/20230818064703.154183-1-junfeng.guo@intel.com/
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
iavf: add support for offloading tc U32 cls filters
iavf: refactor add/del FDIR filters
ice: enable FDIR filters from raw binary patterns for VFs
ice: add method to disable FDIR SWAP option
virtchnl: support raw packet in protocol header
ice: add API for parser profile initialization
ice: add UDP tunnels support to the parser
ice: support turning on/off the parser's double vlan mode
ice: add parser execution main loop
ice: add parser internal helper functions
ice: add debugging functions for the parser sections
ice: parse and init various DDP parser sections
ice: add parser create and destroy skeleton
====================
Link: https://patch.msgid.link/20240813222249.3708070-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'req_vec_chunks' is used to store the vector info received
from the device control plane. The memory for it is allocated
in idpf_send_alloc_vectors_msg and returns an error if the memory
allocation fails.
'req_vec_chunks' cannot be NULL in the later code flow. So remove
the conditional check to extract the vector ids received from
the device control plane.
Smatch static checker warning:
drivers/net/ethernet/intel/idpf/idpf_lib.c:417 idpf_intr_req()
error: we previously assumed 'adapter->req_vec_chunks'
could be null (see line 360)
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/intel-wired-lan/a355ae8a-9011-4a85-a4d1-5b2793bb5f7b@stanley.mountain/
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240814175903.4166390-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows completely removing the remove function. Nothing is being done
manually now.
Tested on TP-LINK Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240813170516.7301-4-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows removing ag71xx_mdio_remove.
Removed ag.mii_bus variable. Local one can be used with devm. Easier to
reason about as mii_bus is only used here now. Also shrinks the struct
slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240813170516.7301-3-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows removal of clk_prepare_enable to simplify the code slightly.
Tested on a TP-LINK Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20240813170516.7301-2-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use new ipv6_addr_cpu_to_be32 and ipv6_addr_be32_to_cpu helpers,
and IPV6_ADDR_WORDS. This is arguably slightly nicer.
No functional change intended.
Compile tested only.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/netdev/c7684349-535c-45a4-9a74-d47479a50020@lunn.ch/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240813-ipv6_addr-helpers-v2-3-5c974f8cca3e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use ipv6_addr_cpu_to_be32 and ipv6_addr_be32_to_cpu helpers to convert
address, rather than open coding the conversion.
No functional change intended.
Compile tested only.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/netdev/c7684349-535c-45a4-9a74-d47479a50020@lunn.ch/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240813-ipv6_addr-helpers-v2-2-5c974f8cca3e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I was revisiting the topic of 802.1ad treatment in the Ocelot switch [0]
and realized that not only is its basic VLAN classification pipeline
improper for offloading vlan_protocol 802.1ad bridges, but also improper
for offloading regular 802.1Q bridges already.
Namely, 802.1ad-tagged traffic should be treated as VLAN-untagged by
bridged ports, but this switch treats it as if it was 802.1Q-tagged with
the same VID as in the 802.1ad header. This is markedly different to
what the Linux bridge expects; see the "other_tpid()" function in
tools/testing/selftests/net/forwarding/bridge_vlan_aware.sh.
An idea came to me that the VCAP IS1 TCAM is more powerful than I'm
giving it credit for, and that it actually overwrites the classified VID
before the VLAN Table lookup takes place. In other words, it can be
used even to save a packet from being dropped on ingress due to VLAN
membership.
Add a sophisticated TCAM rule hardcoded into the driver to force the
switch to behave like a Linux bridge with vlan_filtering 1 vlan_protocol
802.1Q.
Regarding the lifetime of the filter: eventually the bridge will
disappear, and vlan_filtering on the port will be restored to 0 for
standalone mode. Then the filter will be deleted.
[0]: https://lore.kernel.org/netdev/20201009122947.nvhye4hvcha3tljh@skbuf/
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained by Horatiu Vultur in commit 603ead96582d ("net: sparx5: Add
spinlock for frame transmission from CPU") which is for a similar
hardware design, multiple CPUs can simultaneously perform injection
or extraction. There are only 2 register groups for injection and 2
for extraction, and the driver only uses one of each. So we'd better
serialize access using spin locks, otherwise frame corruption is
possible.
Note that unlike in sparx5, FDMA in ocelot does not have this issue
because struct ocelot_fdma_tx_ring already contains an xmit_lock.
I guess this is mostly a problem for NXP LS1028A, as that is dual core.
I don't think VSC7514 is. So I'm blaming the commit where LS1028A (aka
the felix DSA driver) started using register-based packet injection and
extraction.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 distinct code paths (listed below) in the source code which
set up an injection header for Ocelot(-like) switches. Code path (2)
lacks the QoS class and source port being set correctly. Especially the
improper QoS classification is a problem for the "ocelot-8021q"
alternative DSA tagging protocol, because we support tc-taprio and each
packet needs to be scheduled precisely through its time slot. This
includes PTP, which is normally assigned to a traffic class other than
0, but would be sent through TC 0 nonetheless.
The code paths are:
(1) ocelot_xmit_common() from net/dsa/tag_ocelot.c - called only by the
standard "ocelot" DSA tagging protocol which uses NPI-based
injection - sets up bit fields in the tag manually to account for
a small difference (destination port offset) between Ocelot and
Seville. Namely, ocelot_ifh_set_dest() is omitted out of
ocelot_xmit_common(), because there's also seville_ifh_set_dest().
(2) ocelot_ifh_set_basic(), called by:
- ocelot_fdma_prepare_skb() for FDMA transmission of the ocelot
switchdev driver
- ocelot_port_xmit() -> ocelot_port_inject_frame() for
register-based transmission of the ocelot switchdev driver
- felix_port_deferred_xmit() -> ocelot_port_inject_frame() for the
DSA tagger ocelot-8021q when it must transmit PTP frames (also
through register-based injection).
sets the bit fields according to its own logic.
The problem is that (2) doesn't call ocelot_ifh_set_qos_class().
Copying that logic from ocelot_xmit_common() fixes that.
Unfortunately, although desirable, it is not easily possible to
de-duplicate code paths (1) and (2), and make net/dsa/tag_ocelot.c
directly call ocelot_ifh_set_basic()), because of the ocelot/seville
difference. This is the "minimal" fix with some logic duplicated (but
at least more consolidated).
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
register injection
Problem description
-------------------
On an NXP LS1028A (felix DSA driver) with the following configuration:
- ocelot-8021q tagging protocol
- VLAN-aware bridge (with STP) spanning at least swp0 and swp1
- 8021q VLAN upper interfaces on swp0 and swp1: swp0.700, swp1.700
- ptp4l on swp0.700 and swp1.700
we see that the ptp4l instances do not see each other's traffic,
and they all go to the grand master state due to the
ANNOUNCE_RECEIPT_TIMEOUT_EXPIRES condition.
Jumping to the conclusion for the impatient
-------------------------------------------
There is a zero-day bug in the ocelot switchdev driver in the way it
handles VLAN-tagged packet injection. The correct logic already exists in
the source code, in function ocelot_xmit_get_vlan_info() added by commit
5ca721c54d86 ("net: dsa: tag_ocelot: set the classified VLAN during xmit").
But it is used only for normal NPI-based injection with the DSA "ocelot"
tagging protocol. The other injection code paths (register-based and
FDMA-based) roll their own wrong logic. This affects and was noticed on
the DSA "ocelot-8021q" protocol because it uses register-based injection.
By moving ocelot_xmit_get_vlan_info() to a place that's common for both
the DSA tagger and the ocelot switch library, it can also be called from
ocelot_port_inject_frame() in ocelot.c.
We need to touch the lines with ocelot_ifh_port_set()'s prototype
anyway, so let's rename it to something clearer regarding what it does,
and add a kernel-doc. ocelot_ifh_set_basic() should do.
Investigation notes
-------------------
Debugging reveals that PTP event (aka those carrying timestamps, like
Sync) frames injected into swp0.700 (but also swp1.700) hit the wire
with two VLAN tags:
00000000: 01 1b 19 00 00 00 00 01 02 03 04 05 81 00 02 bc
~~~~~~~~~~~
00000010: 81 00 02 bc 88 f7 00 12 00 2c 00 00 02 00 00 00
~~~~~~~~~~~
00000020: 00 00 00 00 00 00 00 00 00 00 00 01 02 ff fe 03
00000030: 04 05 00 01 00 04 00 00 00 00 00 00 00 00 00 00
00000040: 00 00
The second (unexpected) VLAN tag makes felix_check_xtr_pkt() ->
ptp_classify_raw() fail to see these as PTP packets at the link
partner's receiving end, and return PTP_CLASS_NONE (because the BPF
classifier is not written to expect 2 VLAN tags).
The reason why packets have 2 VLAN tags is because the transmission
code treats VLAN incorrectly.
Neither ocelot switchdev, nor felix DSA, declare the NETIF_F_HW_VLAN_CTAG_TX
feature. Therefore, at xmit time, all VLANs should be in the skb head,
and none should be in the hwaccel area. This is done by:
static struct sk_buff *validate_xmit_vlan(struct sk_buff *skb,
netdev_features_t features)
{
if (skb_vlan_tag_present(skb) &&
!vlan_hw_offload_capable(features, skb->vlan_proto))
skb = __vlan_hwaccel_push_inside(skb);
return skb;
}
But ocelot_port_inject_frame() handles things incorrectly:
ocelot_ifh_port_set(ifh, port, rew_op, skb_vlan_tag_get(skb));
void ocelot_ifh_port_set(struct sk_buff *skb, void *ifh, int port, u32 rew_op)
{
(...)
if (vlan_tag)
ocelot_ifh_set_vlan_tci(ifh, vlan_tag);
(...)
}
The way __vlan_hwaccel_push_inside() pushes the tag inside the skb head
is by calling:
static inline void __vlan_hwaccel_clear_tag(struct sk_buff *skb)
{
skb->vlan_present = 0;
}
which does _not_ zero out skb->vlan_tci as seen by skb_vlan_tag_get().
This means that ocelot, when it calls skb_vlan_tag_get(), sees
(and uses) a residual skb->vlan_tci, while the same VLAN tag is
_already_ in the skb head.
The trivial fix for double VLAN headers is to replace the content of
ocelot_ifh_port_set() with:
if (skb_vlan_tag_present(skb))
ocelot_ifh_set_vlan_tci(ifh, skb_vlan_tag_get(skb));
but this would not be correct either, because, as mentioned,
vlan_hw_offload_capable() is false for us, so we'd be inserting dead
code and we'd always transmit packets with VID=0 in the injection frame
header.
I can't actually test the ocelot switchdev driver and rely exclusively
on code inspection, but I don't think traffic from 8021q uppers has ever
been injected properly, and not double-tagged. Thus I'm blaming the
introduction of VLAN fields in the injection header - early driver code.
As hinted at in the early conclusion, what we _want_ to happen for
VLAN transmission was already described once in commit 5ca721c54d86
("net: dsa: tag_ocelot: set the classified VLAN during xmit").
ocelot_xmit_get_vlan_info() intends to ensure that if the port through
which we're transmitting is under a VLAN-aware bridge, the outer VLAN
tag from the skb head is stripped from there and inserted into the
injection frame header (so that the packet is processed in hardware
through that actual VLAN). And in all other cases, the packet is sent
with VID=0 in the injection frame header, since the port is VLAN-unaware
and has logic to strip this VID on egress (making it invisible to the
wire).
Fixes: 08d02364b12f ("net: mscc: fix the injection header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently blindly deletes its cache of RSS cotexts and
ntuple filters when the ethtool channel count is changing. It also
deletes the ntuple filters cache when the default indirection table
is changing.
The core will not allow ethtool channels to drop below any that
have been configured as ntuple destinations since this commit from 2022:
47f3ecf4763d ("ethtool: Fail number of channels change when it conflicts with rxnfc")
So there is absolutely no need to delete the ntuple filters and
RSS contexts when changing ethtool channels.
It is also unnecessary to delete ntuple filters when the default
RSS indirection table is changing.
Remove bnxt_clear_usr_fltrs() and bnxt_clear_rss_ctxis() from the
ethtool ops and change them to static functions.
This bug will cause confusion to the end user and causes failure when
running the rss_ctx.py selftest.
Fixes: 1018319f949c ("bnxt_en: Invalidate user filters when needed")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20240725111912.7bc17cf6@kernel.org/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240814225429.199280-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 2acda57736de ("net/mlx5e: Improve remote NUMA preferences used for the IRQ affinity hints")
removed the usage of cpumask_local_spread().
The issue explained in this commit was fixed by
commit 406d394abfcd ("cpumask: improve on cpumask_local_spread() locality").
Since this commit, mlx5_cpumask_default_spread() is having the same
behavior as cpumask_local_spread().
This commit is about :
- removing the specific logic and use cpumask_local_spread() instead
- passing mlx5_core_dev as argument to more flexibility
mlx5_cpumask_default_spread() is kept as it could be useful for some
future specific quirks.
Signed-off-by: Erwan Velu <e.velu@criteo.com>
Acked-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240812082244.22810-1-e.velu@criteo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now, ifa_dev is only set in inet_alloc_ifa() and never
NULL after ifa gets visible.
Let's remove the unneeded NULL check for ifa->ifa_dev.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240809235406.50187-4-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Increase max_mtu from 1500 to 1518 bytes when not configured for jumbo
frames. Use 1536 as a starting point as documented in macb.h for
oversized (big) frames, which is the configuration applied in case
jumbo frames capability is not configured; ref. macb_main.c.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Link: https://patch.msgid.link/20240812090657.583821-1-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
Documentation/devicetree/bindings/net/fsl,qoriq-mc-dpmac.yaml
c25504a0ba36 ("dt-bindings: net: fsl,qoriq-mc-dpmac: add missed property phys")
be034ee6c33d ("dt-bindings: net: fsl,qoriq-mc-dpmac: using unevaluatedProperties")
https://lore.kernel.org/20240815110934.56ae623a@canb.auug.org.au
drivers/net/dsa/vitesse-vsc73xx-core.c
5b9eebc2c7a5 ("net: dsa: vsc73xx: pass value in phy_write operation")
fa63c6434b6f ("net: dsa: vsc73xx: check busy flag in MDIO operations")
2524d6c28bdc ("net: dsa: vsc73xx: use defined values in phy operations")
https://lore.kernel.org/20240813104039.429b9fe6@canb.auug.org.au
Resolve by using FIELD_PREP(), Stephen's resolution is simpler.
Adjacent changes:
net/vmw_vsock/af_vsock.c
69139d2919dd ("vsock: fix recursive ->recvmsg calls")
744500d81f81 ("vsock: add support for SIOCOUTQ ioctl")
Link: https://patch.msgid.link/20240815141149.33862-1-pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_request_regions is called to apply for PCI I/O and memory resources
when the driver is initialized, Therefore, when the driver is uninstalled,
pci_release_regions should be used to release PCI I/O and memory resources
instead of pci_release_mem_regions is used to release memory reasouces
only.
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
