| Age | Commit message (Collapse) | Author |
|---|
|
No need to stop ctlr if it was already stopped. It can cause timeout
warns. Steps:
- ifconfig eth0 down
- ethtool -l eth0 rx 8 tx 8
- ethtool -l eth0 rx 1 tx 1
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma ctlr is reseted to 0 while cpdma soft reset, thus cpdma ctlr
cannot be configured after cpdma is stopped. So restoring content
of cpdma ctlr while off/on procedure is needed. The cpdma ctlr off/on
procedure is present while interface down/up and while changing number
of channels with ethtool. In order to not restore content in many
places, move it to cpdma_ctlr_start().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While create/destroy channel operation memory is not freed. It was
supposed that memory is freed while driver remove. But a channel
can be created and destroyed many times while changing number of
channels with ethtool.
Based on net-next/master
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This node pointer is returned by of_get_child_by_name() with refcount
incremented in this function. of_node_put() on it before exitting this
function.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not necessary to free memory allocated with devm_kzalloc in the
remove path and using kfree leads to a double free.
Fixes: 84640e27f230 ("net: netcp: Add Keystone NetCP core ethernet
driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
et131x: min_mtu 64, max_mtu 9216
altera_tse: min_mtu 64, max_mtu 1500
amd8111e: min_mtu 60, max_mtu 9000
bnad: min_mtu 46, max_mtu 9000
macb: min_mtu 68, max_mtu 1500 or 10240 depending on hardware capability
xgmac: min_mtu 46, max_mtu 9000
cxgb2: min_mtu 68, max_mtu 9582 (pm3393) or 9600 (vsc7326)
enic: min_mtu 68, max_mtu 9000
gianfar: min_mtu 50, max_mu 9586
hns_enet: min_mtu 68, max_mtu 9578 (v1) or 9706 (v2)
ksz884x: min_mtu 60, max_mtu 1894
myri10ge: min_mtu 68, max_mtu 9000
natsemi: min_mtu 64, max_mtu 2024
nfp: min_mtu 68, max_mtu hardware-specific
forcedeth: min_mtu 64, max_mtu 1500 or 9100, depending on hardware
pch_gbe: min_mtu 46, max_mtu 10300
pasemi_mac: min_mtu 64, max_mtu 9000
qcaspi: min_mtu 46, max_mtu 1500
- remove qcaspi_netdev_change_mtu as it is now redundant
rocker: min_mtu 68, max_mtu 9000
sxgbe: min_mtu 68, max_mtu 9000
stmmac: min_mtu 46, max_mtu depends on hardware
tehuti: min_mtu 60, max_mtu 16384
- driver had no max mtu checking, but product docs say 16k jumbo packets
are supported by the hardware
netcp: min_mtu 68, max_mtu 9486
- remove netcp_ndo_change_mtu as it is now redundant
via-velocity: min_mtu 64, max_mtu 9000
octeon: min_mtu 46, max_mtu 65370
CC: netdev@vger.kernel.org
CC: Mark Einon <mark.einon@gmail.com>
CC: Vince Bridgers <vbridger@opensource.altera.com>
CC: Rasesh Mody <rasesh.mody@qlogic.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Christian Benvenuti <benve@cisco.com>
CC: Sujith Sankar <ssujith@cisco.com>
CC: Govindarajulu Varadarajan <_govind@gmx.com>
CC: Neel Patel <neepatel@cisco.com>
CC: Claudiu Manoil <claudiu.manoil@freescale.com>
CC: Yisen Zhuang <yisen.zhuang@huawei.com>
CC: Salil Mehta <salil.mehta@huawei.com>
CC: Hyong-Youb Kim <hykim@myri.com>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Olof Johansson <olof@lixom.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Byungho An <bh74.an@samsung.com>
CC: Girish K S <ks.giri@samsung.com>
CC: Vipul Pandya <vipul.pandya@samsung.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Wingman Kwok <w-kwok2@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
While build testing with randconfig on x86, I ran into this warning
that appears to have been around forever
drivers/net/ethernet/ti/tlan.c: In function ‘tlan_probe1’:
drivers/net/ethernet/ti/tlan.c:614:1: error: label ‘err_out’ defined but not used [-Werror=unused-label]
This can be trivially avoided by just moving the label into the
existing #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to enable CPSW RGMII internal delay (id mode) bits
when rgmii internal delay is configured in phy.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the cpsw_fill_rx_channels()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ce52c744574b ("net: ethernet: ti: cpsw: add ethtool channels support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.
How many channels are supported and enabled:
$ ethtool -l ethX
Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6
Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
internals
Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupts shouldn't be disabled while receiving skb, but while
ctrl_stop, the channels are stopped and all remaining packets are
handled with netif_receive_skb(), it can cause WARN_ONCE when ctrl
is stopping while not all packets were handled with NAPIs:
lock_irq_save
cpdma_ctlr_stop
cpdma_chan_top
__cpdma_chan_free
cpsw_rx_handler
netif_receive_skb
So, split locking while ctrl stop thus interrupts are still
enabled while skbs handling. It can cause WARN_ONCE in rare
cases when ctrl is stopping while not all packets were handled
with NAPIs.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to hold pdev link when only dev is needed.
This allows to simplify a bunch of cpsw->pdev->dev now and farther.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch simply create holder for common data and as a start moves
pdev var to it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to check const slave num in runtime for every packet,
and ndev for slaves w/o ndev is anyway NULL. So remove redundant
check and macro.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to hold link to clk, it's used only once
while probe.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need in priv here.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At poll handler no possibility to figure out which network device is
handling packets, as cpdma channels are common for both network
devices in dual_emac mode. Currently, the messages are printed only
for one device, in fact, there is two. This print msg is incorrect
and seems is not very useful, so drop it from poll handler.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As second net dev is created only in case of dual_emac mode, port
number can be figured out in simpler way. Also no need to pass
redundant ndev struct.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a preparatory patch for converting qdisc linked list into a
hashtable. As we'll need to include hashtable.h in netdevice.h, we first
have to make sure that this will not introduce symbol conflicts for any of
the netdevice.h users.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kmemleak reports following false positive memory leaks for each sk
buffers allocated by CPSW (__netdev_alloc_skb_ip_align()) in
cpsw_ndo_open() and cpsw_rx_handler():
unreferenced object 0xea915000 (size 2048):
comm "systemd-network", pid 713, jiffies 4294938323 (age 102.180s)
hex dump (first 32 bytes):
00 58 91 ea ff ff ff ff ff ff ff ff ff ff ff ff .X..............
ff ff ff ff ff ff fd 0f 00 00 00 00 00 00 00 00 ................
backtrace:
[<c0108680>] __kmalloc_track_caller+0x1a4/0x230
[<c0529eb4>] __alloc_skb+0x68/0x16c
[<c052c884>] __netdev_alloc_skb+0x40/0x104
[<bf1ad29c>] cpsw_ndo_open+0x374/0x670 [ti_cpsw]
[<c053c3d4>] __dev_open+0xb0/0x114
[<c053c690>] __dev_change_flags+0x9c/0x14c
[<c053c760>] dev_change_flags+0x20/0x50
[<c054bdcc>] do_setlink+0x2cc/0x78c
[<c054c358>] rtnl_setlink+0xcc/0x100
[<c054b34c>] rtnetlink_rcv_msg+0x184/0x224
[<c056467c>] netlink_rcv_skb+0xa8/0xc4
[<c054b1c0>] rtnetlink_rcv+0x2c/0x34
[<c0564018>] netlink_unicast+0x16c/0x1f8
[<c0564498>] netlink_sendmsg+0x334/0x348
[<c052015c>] sock_sendmsg+0x1c/0x2c
[<c05213e0>] SyS_sendto+0xc0/0xe8
unreferenced object 0xec861780 (size 192):
comm "softirq", pid 0, jiffies 4294938759 (age 109.540s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 b0 5a ed 00 00 00 00 00 00 00 00 ......Z.........
backtrace:
[<c0107830>] kmem_cache_alloc+0x190/0x208
[<c052c768>] __build_skb+0x30/0x98
[<c052c8fc>] __netdev_alloc_skb+0xb8/0x104
[<bf1abc54>] cpsw_rx_handler+0x68/0x1e4 [ti_cpsw]
[<bf11aa30>] __cpdma_chan_free+0xa8/0xc4 [davinci_cpdma]
[<bf11ab98>] __cpdma_chan_process+0x14c/0x16c [davinci_cpdma]
[<bf11abfc>] cpdma_chan_process+0x44/0x5c [davinci_cpdma]
[<bf1adc78>] cpsw_rx_poll+0x1c/0x9c [ti_cpsw]
[<c0539180>] net_rx_action+0x1f0/0x2ec
[<c003881c>] __do_softirq+0x134/0x258
[<c0038a00>] do_softirq+0x68/0x70
[<c0038adc>] __local_bh_enable_ip+0xd4/0xe8
[<c0640994>] _raw_spin_unlock_bh+0x30/0x34
[<c05f4e9c>] igmp6_group_added+0x4c/0x1bc
[<c05f6600>] ipv6_dev_mc_inc+0x398/0x434
[<c05dba74>] addrconf_dad_work+0x224/0x39c
This happens because CPSW allocates SK buffers and then passes
pointers on them in CPDMA where they stored in internal CPPI RAM
(SRAM) which belongs to DEV MMIO space. Kmemleak does not scan IO
memory and so reports memory leaks.
Hence, mark allocated sk buffers as false positive explicitly.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct cpdma_desc_pool->used_desc field can be safely removed from
CPDMA driver (and hot patch) because used_descs counter is used just
for pool consistency check at CPDMA deinitialization and now this
check can be re-implemnted using gen_pool_size(pool->gen_pool) !=
gen_pool_avail(pool->gen_pool).
More over, this will allow to get rid of warnings in
cpdma_desc_pool_destro()-> WARN_ON(pool->used_desc) which may happen
because the used_descs is used unprotected, since CPDMA has been
switched to use genalloc, and may get wrong values on SMP.
Hence, remove used_desc from struct cpdma_desc_pool.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_parse_phandle
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use of_platform_depopulate() in cpsw_remove() instead of
of_device_unregister(), because CSPW child devices will not be
recreated otherwise on next insmod. of_platform_depopulate() is
correct way now as it will ensure that all steps done in
of_platform_populate() are reverted, including cleaning up of
OF_POPULATED flag.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The L3 error will be generated and system will crash during unloading
of CPSW driver if CPSW is used as module and ethX devices are down.
This happens because CPSW can be power off by PM runtime now when ethX
devices are down.
Hence, ensure that CPSW powered up by PM runtime before performing any
deinitialization actions which require CPSW registers access. In case
of PM runtime error just leave cpsw_remove() as we can't do anything
anymore.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix deadlock in cpdma_ctlr_destroy() which is triggered now on
cpsw module removal:
cpsw_remove()
- cpdma_ctlr_destroy()
- spin_lock_irqsave(&ctlr->lock, flags)
- cpdma_ctlr_stop()
- spin_lock_irqsave(&ctlr->lock, flags);
- cpdma_chan_destroy()
- spin_lock_irqsave(&ctlr->lock, flags);
The issue has not been observed before because CPDMA channels have
been destroyed manually by CPSW until commit d941ebe88a41 ("net:
ethernet: ti: cpsw: use destroy ctlr to destroy channels") was merged.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Such a big dump of register values is hardly useful on a production
system.
Another downside of the now removed functions is that calling
emac_dump_regs resulted in at least 87 calls to dev_info while holding a
spinlock and having irqs off which is a big source of latency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing free_netdev() before return from function
cpmac_probe() in the error handling case.
This patch revert commit 0465be8f4f1d ("net: cpmac: fix in
releasing resources"), which changed to only free_netdev
while register_netdev failed.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In 'cpmac_open', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Also, we don't need to free these resources if the allocation has failed.
So I have slighly modified the goto label in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So
there is no reason to have this symbol visible.
A further optimisation would be to put the code for both symbols into a
single module which would allow to not export at least cpsw_phy_sel()
and simplify the module load process.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in cpmac_set_settings, but this
check is already done in dev_ethtool, so no need to repeat it before
calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
