| Age | Commit message (Collapse) | Author |
|---|
|
Hence all users of davinci_cpdma switched to skb_put_padto() the frame
padding can be removed from it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df9322 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098ed ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df9322 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
am65_cpsw_port_offload_fwd_mark_update()
The am65_cpsw_port_offload_fwd_mark_update() causes NULL exception crash
when there is at least one disabled port and any other port added to the
bridge first time.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000858
pc : am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
lr : am65_cpsw_netdevice_event+0x8c/0xf0
Call trace:
am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
notifier_call_chain+0x54/0x98
raw_notifier_call_chain+0x14/0x20
call_netdevice_notifiers_info+0x34/0x78
__netdev_upper_dev_link+0x1c8/0x290
netdev_master_upper_dev_link+0x1c/0x28
br_add_if+0x3f0/0x6d0 [bridge]
Fix it by adding proper check for port->ndev != NULL.
Fixes: 2934db9bcb30 ("net: ti: am65-cpsw-nuss: Add netdevice notifiers")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b0e81817629a496854ff1799f6cbd89597db65fd. Explicit
driver dependency on the bridge is no longer needed since
switchdev_bridge_port_{,un}offload() is no longer implemented by the
bridge driver but by switchdev.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e81817629a ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit that introduced devlink support released devlink resources in
wrong order, that made an unwind flow to be asymmetrical. In addition,
the am65-cpsw-nuss used internal to devlink core field - registered.
In order to fix the unwind flow and remove such access to the
registered field, rewrite the code to call devlink_port_unregister only
on registered ports.
Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, all drivers depend on the bool CONFIG_NET_SWITCHDEV, but only
the drivers that call some sort of function exported by the bridge, like
br_vlan_enabled() or whatever, have an extra dependency on CONFIG_BRIDGE.
Since the blamed commit, all switchdev drivers have a functional
dependency upon switchdev_bridge_port_{,un}offload(), which is a pair of
functions exported by the bridge module and not by the bridge-independent
part of CONFIG_NET_SWITCHDEV.
Problems appear when we have:
CONFIG_BRIDGE=m
CONFIG_NET_SWITCHDEV=y
CONFIG_TI_CPSW_SWITCHDEV=y
because cpsw, am65_cpsw and sparx5 will then be built-in but they will
call a symbol exported by a loadable module. This is not possible and
will result in the following build error:
drivers/net/ethernet/ti/cpsw_new.o: in function `cpsw_netdevice_event':
drivers/net/ethernet/ti/cpsw_new.c:1520: undefined reference to
`switchdev_bridge_port_offload'
drivers/net/ethernet/ti/cpsw_new.c:1537: undefined reference to
`switchdev_bridge_port_unoffload'
As mentioned, the other switchdev drivers don't suffer from this because
switchdev_bridge_port_offload() is not the first symbol exported by the
bridge that they are calling, so they already needed to deal with this
in the same way.
Fixes: 2f5dc00f7a3e ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with commit 4f2673b3a2b6 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c4a ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef716 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d355 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-20-toke@redhat.com
|
|
When changing number of TX queues using ethtool:
# ethtool -L eth0 tx 1
[ 135.301047] Unable to handle kernel paging request at virtual address 00000000af5d0000
[...]
[ 135.525128] Call trace:
[ 135.525142] dma_release_from_dev_coherent+0x2c/0xb0
[ 135.525148] dma_free_attrs+0x54/0xe0
[ 135.525156] k3_cppi_desc_pool_destroy+0x50/0xa0
[ 135.525164] am65_cpsw_nuss_remove_tx_chns+0x88/0xdc
[ 135.525171] am65_cpsw_set_channels+0x3c/0x70
[...]
This is because k3_cppi_desc_pool_destroy() which is called after
k3_udma_glue_release_tx_chn() in am65_cpsw_nuss_remove_tx_chns()
references struct device that is unregistered at the end of
k3_udma_glue_release_tx_chn()
Therefore the right order is to call k3_cppi_desc_pool_destroy() and
destroy desc pool before calling k3_udma_glue_release_tx_chn().
Fix this throughout the driver.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As already done for mvneta and mvpp2, enable skb recycling for ti
ethernet drivers
ti driver on net-next:
----------------------
[perf top]
47.15% [kernel] [k] _raw_spin_unlock_irqrestore
11.77% [kernel] [k] __cpdma_chan_free
3.16% [kernel] [k] ___bpf_prog_run
2.52% [kernel] [k] cpsw_rx_vlan_encap
2.34% [kernel] [k] __netif_receive_skb_core
2.27% [kernel] [k] free_unref_page
2.26% [kernel] [k] kmem_cache_free
2.24% [kernel] [k] kmem_cache_alloc
1.69% [kernel] [k] __softirqentry_text_start
1.61% [kernel] [k] cpsw_rx_handler
1.19% [kernel] [k] page_pool_release_page
1.19% [kernel] [k] clear_bits_ll
1.15% [kernel] [k] page_frag_free
1.06% [kernel] [k] __dma_page_dev_to_cpu
0.99% [kernel] [k] memset
0.94% [kernel] [k] __alloc_pages_bulk
0.92% [kernel] [k] kfree_skb
0.85% [kernel] [k] packet_rcv
0.78% [kernel] [k] page_address
0.75% [kernel] [k] v7_dma_inv_range
0.71% [kernel] [k] __lock_text_start
[iperf3 tcp]
[ 5] 0.00-10.00 sec 873 MBytes 732 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 866 MBytes 726 Mbits/sec receiver
ti + skb recycling:
-------------------
[perf top]
40.58% [kernel] [k] _raw_spin_unlock_irqrestore
16.18% [kernel] [k] __softirqentry_text_start
10.33% [kernel] [k] __cpdma_chan_free
2.62% [kernel] [k] ___bpf_prog_run
2.05% [kernel] [k] cpsw_rx_vlan_encap
2.00% [kernel] [k] kmem_cache_alloc
1.86% [kernel] [k] __netif_receive_skb_core
1.80% [kernel] [k] kmem_cache_free
1.63% [kernel] [k] cpsw_rx_handler
1.12% [kernel] [k] cpsw_rx_mq_poll
1.11% [kernel] [k] page_pool_put_page
1.04% [kernel] [k] _raw_spin_unlock
0.97% [kernel] [k] clear_bits_ll
0.90% [kernel] [k] packet_rcv
0.88% [kernel] [k] __dma_page_dev_to_cpu
0.85% [kernel] [k] kfree_skb
0.80% [kernel] [k] memset
0.71% [kernel] [k] __lock_text_start
0.66% [kernel] [k] v7_dma_inv_range
0.64% [kernel] [k] gen_pool_free_owner
[iperf3 tcp]
[ 5] 0.00-10.00 sec 884 MBytes 742 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 878 MBytes 735 Mbits/sec receiver
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cdc-wdm: s/kill_urbs/poison_urbs/ to fix build
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/cpsw_ale.c:88: warning: expecting prototype for struct ale_dev_id. Prototype was for struct cpsw_ale_dev_id instead
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ret' is known to be 0 here.
The expected error code is stored in 'tx_pipe->dma_queue', so use it
instead.
While at it, switch from %d to %pe which is more user friendly.
Fixes: 84640e27f230 ("net: netcp: Add Keystone NetCP core ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in bugfix commit 6ab4c3117aec ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
|
|
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
J721e, J7200 and AM64 have multi port switches which can work in multi
mac mode and in switch mode. Add support for configuring this HW in
switch mode using devlink and switchdev notifiers.
Support is similar to existing CPSW switchdev implementation of TI's 32 bit
platform like AM33/AM43/AM57.
To enable switch mode:
devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence AM65 CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register netdevice notifiers in order to receive notification when
individual MAC ports are added to the HW bridge.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AM65 NUSS ethernet switch on K3 devices can be configured to work either
in independent mac mode where each port acts as independent network
interface (multi mac) or switch mode.
Add devlink hooks to provide a way to switch b/w these modes.
Rationale to use devlink instead of defaulting to bridge mode is that
SoC use cases require to support multiple independent MAC ports with no
switching so that users can use software bridges with multi-mac
configuration (e.g: to support LAG, HSR/PRP, etc). Also, switching
between multi mac and switch mode requires significant Port and ALE
reconfiguration, therefore is easier to be made as part of mode change
devlink hooks. It also allows to keep user interface similar to what
was implemented for the previous generation of TI CPSW IP
(on AM33/AM43/AM57 SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align netdevice statistics when the device is running in XDP mode
to other upstream drivers. In particular report to user-space rx
packets even if they are not forwarded to the networking stack
(XDP_PASS) but if they are redirected (XDP_REDIRECT), dropped (XDP_DROP)
or sent back using the same interface (XDP_TX). This patch allows the
system administrator to verify the device is receiving data correctly.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a457cb17dd9c58c116d64ee34c354b2e89c0ff8f.1612375372.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the more modern API to get the match data out of the of match table.
This saves some code, lines, and nicely avoids referencing the match
table when it is undefined with configurations where CONFIG_OF=n.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-omap@vger.kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210123034428.2841052-3-swboyd@chromium.org
|
|
The TI AM64x SoCs Gigabit Ethernet Switch subsystem (CPSW3g NUSS) has three
ports (2 ext. ports) and provides Ethernet packet communication for the
device and can be configured in multi port mode or as an Ethernet switch.
This patch adds support for the corresponding CPSW3g version.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The AM642x CPSW3g is similar to j721e-cpswxg except its ALE table size is
512 entries. Add entry for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the glue layer's functions to convert the dma_addr_t to and from CPPI5
address (with the ASEL bits), which should be used within the descriptors
and data buffers.
- Per channel coherency support
The DMAs use the 'ASEL' bits to select data and configuration fetch path.
The ASEL bits are placed at the unused parts of any address field used by
the DMAs (pointers to descriptors, addresses in descriptors, ring base
addresses). The ASEL is not part of the address (the DMAs can address
48bits). Individual channels can be configured to be coherent (via ACP
port) or non coherent individually by configuring the ASEL to appropriate
value.
[1] https://lore.kernel.org/patchwork/cover/1350756/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For DMA API the DMA device should be used as cpsw does not accesses to
descriptors or data buffers in any ways. The DMA does.
Also, drop dma_coerce_mask_and_coherent() setting on CPSW device, as it
should be done by DMA driver which does data movement.
This is required for adding AM64x CPSW3g support where DMA coherency
supported per DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/am65-cpts.c:736: warning: Function parameter or member 'en' not described in 'am65_cpts_rx_enable'
drivers/net/ethernet/ti/am65-cpts.c:736: warning: Excess function parameter 'skb' description in 'am65_cpts_rx_enable'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'ndev' not described in 'am65_cpsw_timer_set'
drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'est_new' not described in 'am65_cpsw_timer_set'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d8a
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceffc1 ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef7838
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1a4 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b9359e ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2fa ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d83 ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1ae3 ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d83 by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc28e
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
