summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/ti/cpsw.c
AgeCommit message (Collapse)Author
2015-08-06drivers: net: cpsw: add separate napi for txMugunthan V N
Instead of processing tx events in isr adding separate napi for tx which improves performance by ~180Mbps with omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis by renaming to napi_rx for better understanding the code. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-06drivers: net: cpsw: dual_emac: simplify napi usageMugunthan V N
Since interrupt is shared between the two ethernet interface and in isr only one napi is scheduled at an instance so having two napis doesn't make any difference. So making napi also as a common resource for the dual ethernet interfaces. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-08-06drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from ↵Mugunthan V N
cpsw itself CPSW interrupts can be disabled by masking CPSW interrupts and clearing interrupt by writing appropriate EOI. So removing all disable_irq/enable_irq as discussed in [1] [1] http://patchwork.ozlabs.org/patch/492741/ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-21drivers: net: cpsw: remove tx event processing in rx napi pollMugunthan V N
With commit c03abd84634d ("net: ethernet: cpsw: don't requests IRQs we don't use") common isr and napi are separated into separate tx isr and rx isr/napi, but still in rx napi tx events are handled. So removing the tx event handling in rx napi. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-09drivers: net: cpsw: fix disabling of tx interrupt in rx isrMugunthan V N
In commit 'c03abd84634d ("net: ethernet: cpsw: don't requests IRQs we don't use")', common isr is split into tx and rx, but in rx isr tx interrupt is also disabledi in cpsw_disable_irq(). So tx interrupts are not handled during rx interrupts and rx napi completion and results in poor tx performance by 40Mbps. Fixing by disabling only rx interrupt in rx isr. Cc: Felipe Balbi <balbi@ti.com> Cc: <stable@vger.kernel.org> # v4.0+ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-07-08drivers: net: cpsw: fix crash while accessing second slave ethernet interfaceMugunthan V N
When cpsw's number of slave is set to 1 in device tree and while accessing second slave ndev and priv in cpsw_tx_interrupt(), there is a kernel crash. This is due to cpsw_get_slave_priv() not verifying number of slaves while retriving netdev priv and returns a invalid memory region. Fixing the issue by introducing number of slave check in cpsw_get_slave_priv() and cpsw_get_slave_ndev(). [ 15.879589] Unable to handle kernel paging request at virtual address 0f0e142c [ 15.888540] pgd = ed374000 [ 15.891359] [0f0e142c] *pgd=00000000 [ 15.895105] Internal error: Oops: 5 [#1] SMP ARM [ 15.899936] Modules linked in: [ 15.903139] CPU: 0 PID: 593 Comm: udhcpc Tainted: G W 4.1.0-12205-gfda8b18-dirty #10 [ 15.912386] Hardware name: Generic AM43 (Flattened Device Tree) [ 15.918557] task: ed2a2e00 ti: ed3fe000 task.ti: ed3fe000 [ 15.924187] PC is at cpsw_tx_interrupt+0x30/0x44 [ 15.929008] LR is at _raw_spin_unlock_irqrestore+0x40/0x44 [ 15.934726] pc : [<c048b9cc>] lr : [<c05ef4f4>] psr: 20000193 [ 15.934726] sp : ed3ffc08 ip : ed2a2e40 fp : 00000000 [ 15.946685] r10: c0969ce8 r9 : c0969cfc r8 : 00000000 [ 15.952129] r7 : 000000c6 r6 : ee54ab00 r5 : ee169c64 r4 : ee534e00 [ 15.958932] r3 : 0f0e0d0c r2 : 00000000 r1 : ed3ffbc0 r0 : 00000001 [ 15.965735] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user [ 15.973261] Control: 10c5387d Table: ad374059 DAC: 00000015 [ 15.979246] Process udhcpc (pid: 593, stack limit = 0xed3fe218) [ 15.985414] Stack: (0xed3ffc08 to 0xed400000) [ 15.989954] fc00: ee54ab00 c009928c c0a9e648 60000193 000032e4 ee169c00 [ 15.998478] fc20: ee169c64 ee169c00 ee169c64 ee54ab00 00000001 00000001 ee67e268 ee008800 [ 16.006995] fc40: ee534800 c009946c ee169c00 ee169c64 c08bd660 c009c370 c009c2a4 000000c6 [ 16.015513] fc60: c08b75c4 c08b0854 00000000 c0098b3c 000000c6 c0098c50 ed3ffcb0 0000003a [ 16.024033] fc80: ed3ffcb0 fa24010c c08b7800 fa240100 ee7e9880 c00094c4 c05ef4e8 60000013 [ 16.032556] fca0: ffffffff ed3ffce4 ee7e9880 c05ef964 00000001 ed2a33d8 00000000 ed2a2e00 [ 16.041080] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800 [ 16.049603] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff 00000001 00000001 [ 16.058121] fd00: ee536bf8 c0487a04 00000000 00000000 ee534800 00000000 00000156 c048c990 [ 16.066645] fd20: 00000000 00000000 c0969f40 00000000 00000000 c05000e8 00000001 00000000 [ 16.075167] fd40: 00000000 c051eefc 00000000 ee67e268 00000000 00000000 ee51b800 ed3ffd9c [ 16.083690] fd60: 00000000 ee67e200 ee51b800 ee7e9880 ee67e268 00000000 00000000 ee67e200 [ 16.092211] fd80: ee51b800 ee7e9880 ee67e268 ee534800 ee67e200 c051eedc ee67e268 00000010 [ 16.100727] fda0: 00000000 00000000 ee7e9880 ee534800 00000000 ee67e268 ee51b800 c05006fc [ 16.109247] fdc0: ee67e268 00000001 c0500488 00000156 ee7e9880 00000000 ed3fe000 fffffff4 [ 16.117771] fde0: ed3fff1c ee7e9880 ee534800 00000148 00000000 ed1f8340 00000000 00000000 [ 16.126289] fe00: 00000000 c05a9054 00000000 00000000 00000156 c0ab62a8 00000010 ed3e7000 [ 16.134812] fe20: 00000000 00000008 edcfb700 ed3fff1c c0fb5f94 ed2a2e00 c0fb5f64 000005d8 [ 16.143336] fe40: c0a9b3b8 00000000 ed3e7070 00000000 00000000 00000000 00009f40 00000000 [ 16.151858] fe60: 00000000 00020022 00110008 00000000 00000000 43004400 00000000 ffffffff [ 16.160374] fe80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 16.168898] fea0: edcfb700 bee5f380 00000014 00000000 ed3fe000 00000000 00004400 c04e2b64 [ 16.177415] fec0: 00000002 c04e3b00 ed3ffeec 00000001 0000011a 00000000 00000000 bee5f394 [ 16.185937] fee0: 00000148 ed3fff10 00000014 00000001 00000000 00000000 ed3ffee4 00000000 [ 16.194459] ff00: 00000000 00000000 00000000 c04e3664 00080011 00000002 06000000 ffffffff [ 16.202980] ff20: 0000ffff ffffffff 0000ffff c008dd54 ee5a6f08 ee636e80 c096972d c0089c14 [ 16.211499] ff40: 00000000 60000013 ee5a6f40 60000013 00000000 ee5a6f40 00000002 00000006 [ 16.220023] ff60: 00000000 edcfb700 00000001 ed2a2e00 c000f60c 00000001 0000011a c008ea34 [ 16.228540] ff80: 00000006 00000000 bee5f380 00000014 bee5f380 00000014 bee5f380 00000122 [ 16.237059] ffa0: c000f7c4 c000f5e0 bee5f380 00000014 00000006 bee5f394 00000148 00000000 [ 16.245581] ffc0: bee5f380 00000014 bee5f380 00000122 fffffd6e 00004300 00004800 00004400 [ 16.254104] ffe0: bee5f378 bee5f36c 000307ec b6f39044 40000010 00000006 ed36fa40 00000000 [ 16.262642] [<c048b9cc>] (cpsw_tx_interrupt) from [<c009928c>] (handle_irq_event_percpu+0x64/0x204) [ 16.272076] [<c009928c>] (handle_irq_event_percpu) from [<c009946c>] (handle_irq_event+0x40/0x64) [ 16.281330] [<c009946c>] (handle_irq_event) from [<c009c370>] (handle_fasteoi_irq+0xcc/0x1a8) [ 16.290220] [<c009c370>] (handle_fasteoi_irq) from [<c0098b3c>] (generic_handle_irq+0x20/0x30) [ 16.299197] [<c0098b3c>] (generic_handle_irq) from [<c0098c50>] (__handle_domain_irq+0x64/0xdc) [ 16.308273] [<c0098c50>] (__handle_domain_irq) from [<c00094c4>] (gic_handle_irq+0x20/0x60) [ 16.316987] [<c00094c4>] (gic_handle_irq) from [<c05ef964>] (__irq_svc+0x44/0x5c) [ 16.324779] Exception stack(0xed3ffcb0 to 0xed3ffcf8) [ 16.330044] fca0: 00000001 ed2a33d8 00000000 ed2a2e00 [ 16.338567] fcc0: 60000013 ee536bf8 60000013 ee51b800 ee7e9880 ee67e268 ee7e9880 ee534800 [ 16.347090] fce0: c0ad0768 ed3ffcf8 c008e910 c05ef4e8 60000013 ffffffff [ 16.353987] [<c05ef964>] (__irq_svc) from [<c05ef4e8>] (_raw_spin_unlock_irqrestore+0x34/0x44) [ 16.362973] [<c05ef4e8>] (_raw_spin_unlock_irqrestore) from [<c0487a04>] (cpdma_check_free_tx_desc+0x60/0x6c) [ 16.373311] [<c0487a04>] (cpdma_check_free_tx_desc) from [<c048c990>] (cpsw_ndo_start_xmit+0xb4/0x1ac) [ 16.383017] [<c048c990>] (cpsw_ndo_start_xmit) from [<c05000e8>] (dev_hard_start_xmit+0x2a4/0x4c0) [ 16.392364] [<c05000e8>] (dev_hard_start_xmit) from [<c051eedc>] (sch_direct_xmit+0xf4/0x210) [ 16.401246] [<c051eedc>] (sch_direct_xmit) from [<c05006fc>] (__dev_queue_xmit+0x2ac/0x7bc) [ 16.409960] [<c05006fc>] (__dev_queue_xmit) from [<c05a9054>] (packet_sendmsg+0xc68/0xeb4) [ 16.418585] [<c05a9054>] (packet_sendmsg) from [<c04e2b64>] (sock_sendmsg+0x14/0x24) [ 16.426663] [<c04e2b64>] (sock_sendmsg) from [<c04e3b00>] (SyS_sendto+0xb4/0xe0) [ 16.434377] [<c04e3b00>] (SyS_sendto) from [<c000f5e0>] (ret_fast_syscall+0x0/0x54) [ 16.442360] Code: e5943118 e593303c e3530000 0a000002 (e5930720) [ 16.448716] ---[ end trace a68159f094d85ba6 ]--- [ 16.453526] Kernel panic - not syncing: Fatal exception in interrupt [ 16.460149] ---[ end Kernel panic - not syncing: Fatal exception in interrupt Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-25net: cpsw: remove redundant calls disabling dma interrupts.Richard Cochran
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There is no need to disable the dma interrupts twice. This patch removes the extra calls. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-25net: cpsw: remove redundant calls enabling dma interrupts.Richard Cochran
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There is no need to enable the dma interrupts twice. This patch removes the extra call. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-25net: cpsw: fix misplaced break statements.Richard Cochran
Having the breaks too far to the left makes parsing the dense switch/case block unnecessarily harder. Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-08ethernet: codespell comment spelling fixesJoe Perches
To test a checkpatch spelling patch, I ran codespell against drivers/net/ethernet/. $ git ls-files drivers/net/ethernet/ | \ while read file ; do \ codespell -w $file; \ done I removed a false positive in e1000_hw.h Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-01net: ti: cpsw: add hibernation callbacksGrygorii Strashko
Setting a dev_pm_ops suspend/resume pair but not a set of hibernation functions means those pm functions will not be called upon hibernation. Fix this by using SIMPLE_DEV_PM_OPS, which appropriately assigns the suspend and hibernation handlers and move cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP to avoid build warnings. Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-28drivers: net: cpsw: Set SECURE for dual_emac ucastGeorge McCollister
Prior to this patch, sending a packet with the source MAC address of one of the CPSW interfaces to one of the CPSW slave ports while it's configured in dual_emac mode would update the port_num field of the VLAN/Unicast Address Table Entry. This would cause it to discard all incoming traffic addressed to that MAC address, essentially rendering the port useless until the ALE table is cleared (by starting and stopping the interface or rebooting.) For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have an ALE table entry: 00 00 00 00 59 90 02 30 e9 43 8f af (VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9) If you configure another device with the same MAC address and connect it to the first CPSW slave port and send some traffic the ALE table entry becomes: 04 00 00 00 59 90 02 30 e9 43 8f af (VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9) >From this point forward all incoming traffic addressed to 90:59:af:8f:43:e9 will be dropped. Setting the SECURE bit for the VLAN/Unicast address table entry for each interface's MAC address corrects the problem. Signed-off-by: George McCollister <george.mccollister@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-30net: cpsw: Add a minimal cpsw-common module for shared codeTony Lindgren
Looks like davinci_emac and cpsw can share some code although the device registers have a different layout. At least the code for getting the MAC address using syscon can be shared by passing the register offset. Let's start with that and set up a minimal shared cpsw-shared.c. Cc: Brian Hutchinson <b.hutchman@gmail.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: arch/arm/boot/dts/imx6sx-sdb.dts net/sched/cls_bpf.c Two simple sets of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-26drivers: net: cpsw: discard dual emac default vlan configurationMugunthan V N
In Dual EMAC, the default VLANs are used to segregate Rx packets between the ports, so adding the same default VLAN to the switch will affect the normal packet transfers. So returning error on addition of dual EMAC default VLANs. Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to break dual EMAC port separations. Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation) Cc: <stable@vger.kernel.org> # v3.9+ Reported-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-19net: ethernet: ti: cpsw: fix buld break when NET_POLL_CONTROLLERFelipe Balbi
Commit c03abd84634d (net: ethernet: cpsw: don't requests IRQs we don't use) left one build breakage when NET_POLL_CONTROLLER is enabled. Fix this build break by referring to the correct irqs_table array. Fixes: c03abd84634d (net: ethernet: cpsw: don't requests IRQs we don't use) Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-18net: ethernet: cpsw: don't requests IRQs we don't useFelipe Balbi
CPSW never uses RX_THRESHOLD or MISC interrupts. In fact, they are always kept masked in their appropriate IRQ Enable register. Instead of allocating an IRQ that never fires, it's best to remove that code altogether and let future patches implement it if anybody needs those. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-18net: ethernet: cpsw: unroll IRQ request loopFelipe Balbi
This patch is in preparation for a nicer IRQ handling scheme where we use different IRQ handlers for each IRQ line (as it should be). Later, we will also drop IRQs offset 0 and 3 because they are always disabled in this driver. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-15drivers: net: cpsw: fix cpsw hung with add vlan using vconfigMugunthan V N
while adding vlan in dual EMAC mode, only specific ports should be subscribed for the vlan, else it will lead to switching mode and if both ports connected to same switch cpsw will hung as it creates a network loop. Fixing this by adding only specific ports in case of dual EMAC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13drivers: net: cpsw: fix multicast flush in dual emac modeMugunthan V N
Since ALE table is a common resource for both the interfaces in Dual EMAC mode and while bringing up the second interface in cpsw_ndo_set_rx_mode() all the multicast entries added by the first interface is flushed out and only second interface multicast addresses are added. Fixing this by flushing multicast addresses based on dual EMAC port vlans which will not affect the other emac port multicast addresses. Fixes: d9ba8f9 (driver: net: ethernet: cpsw: dual emac interface implementation) Cc: <stable@vger.kernel.org> # v3.9+ Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-04net: ethernet: cpsw: fix hangs with interruptsFelipe Balbi
The CPSW IP implements pulse-signaled interrupts. Due to that we must write a correct, pre-defined value to the CPDMA_MACEOIVECTOR register so the controller generates a pulse on the correct IRQ line to signal the End Of Interrupt. The way the driver is written today, all four IRQ lines are requested using the same IRQ handler and, because of that, we could fall into situations where a TX IRQ fires but we tell the controller that we ended an RX IRQ (or vice-versa). This situation triggers an IRQ storm on the reserved IRQ 127 of INTC which will in turn call ack_bad_irq() which will, then, print a ton of: unexpected IRQ trap at vector 00 In order to fix the problem, we are moving all calls to cpdma_ctlr_eoi() inside the IRQ handler and making sure we *always* write the correct value to the CPDMA_MACEOIVECTOR register. Note that the algorithm assumes that IRQ numbers and value-to-be-written-to-EOI are proportional, meaning that a write of value 0 would trigger an EOI pulse for the RX_THRESHOLD Interrupt and that's the IRQ number sitting in the 0-th index of our irqs_table array. This, however, is safe at least for current implementations of CPSW so we will refrain from making the check smarter (and, as a side-effect, slower) until we actually have a platform where IRQ lines are swapped. This patch has been tested for several days with AM335x- and AM437x-based platforms. AM57x was left out because there are still pending patches to enable ethernet in mainline for that platform. A read of the TRM confirms the statement on previous paragraph. Reported-by: Yegor Yefremov <yegorslists@googlemail.com> Fixes: 510a1e7 (drivers: net: davinci_cpdma: acknowledge interrupt properly) Cc: <stable@vger.kernel.org> # v3.9+ Signed-off-by: Felipe Balbi <balbi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-11-16drivers: net: cpsw: Fix TX_IN_SEL offsetJohn Ogness
The TX_IN_SEL offset for the CPSW_PORT/TX_IN_CTL register was incorrect. This caused the Dual MAC mode to never get set when it should. It also caused possible unintentional setting of a bit in the CPSW_PORT/TX_BLKS_REM register. The purpose of setting the Dual MAC mode for this register is to: "... allow packets from both ethernet ports to be written into the FIFO without one port starving the other port." - AM335x ARM TRM Signed-off-by: John Ogness <john.ogness@linutronix.de> Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-31drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch modeLennart Sorensen
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic multicast routing not work. Related to this, when enabling IFF_PROMISC in switch mode, all registered multicast addresses are flushed, resulting in only broadcast and unicast traffic being received. A new cpsw_ale_set_allmulti function now scans through the ALE entry table and adds/removes the host port from the unregistered multicast port mask of each vlan entry depending on the state of IFF_ALLMULTI. In promiscious mode, cpsw_ale_set_allmulti is used to force reception of all multicast traffic in addition to the unicast and broadcast traffic. With this change dynamic multicast and promiscious mode both work in switch mode. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-31drivers: net: cpsw: Fix broken loop condition in switch modeLennart Sorensen
0d961b3b52f566f823070ce2366511a7f64b928c (drivers: net: cpsw: fix buggy loop condition) accidentally fixed a loop comparison in too many places while fixing a real bug. It was correct to fix the dual_emac mode section since there 'i' is used as an index into priv->slaves which is a 0 based array. However the other two changes (which are only used in switch mode) are wrong since there 'i' is actually the ALE port number, and port 0 is the host port, while port 1 and up are the slave ports. Putting the loop condition back in the switch mode section fixes it. A comment has been added to point out the intent clearly to avoid future confusion. Also a comment is fixed that said the opposite of what was actually happening. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-28drivers: net:cpsw: fix probe_dt when only slave 1 is pinned outMugunthan V N
when slave 0 has no phy and slave 1 connected to phy, driver probe will fail as there is no phy id present for slave 0 device tree, so continuing even though no phy-id found, also moving mac-id read later to ensure mac-id is read from device tree even when phy-id entry in not found. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14drivers: net: cpsw: remove child devices while driver detachMugunthan V N
remove all the child devices from the system to make sure that re-insert of cpsw module doesn't fail on child device populated by of_platform_populate(). Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30net: cpsw: Add am33xx MACID readoutMarkus Pargmann
This patch adds a function to get the MACIDs from the am33xx SoC control module registers which hold unique vendor MACIDs. This is only used if of_get_mac_address() fails to get a valid mac address. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Tested-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30net: cpsw: Replace pr_err by dev_errMarkus Pargmann
Use dev_err instead of pr_err. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-30net: cpsw: Add missing return valueMarkus Pargmann
ret is set 0 at this point, so jumping to that error label would result in a return value of 0. Set ret to -ENOMEM to return a proper error value. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Reviewed-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: arch/mips/net/bpf_jit.c drivers/net/can/flexcan.c Both the flexcan and MIPS bpf_jit conflicts were cases of simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-13drivers: net: cpsw: dual_emac: in suspend/resume bring down/up all the netdevMugunthan V N
During suspend and resume in Dual EMAC, second port is not working as in suspend/resume only the first slave netdev is closed and opened. So bring down and up all the interfaces that are up during suspend/resume. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-10drivers: net: cpsw: dual_emac: fix reducing of rx descriptor during ifdownMugunthan V N
In Dual EMAC, when both interface are up and while doing ifdown with heavy traffic then skbs already processed by DMA from that slave emac has to be requeued as still the other interface is up and running. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-09ethernet: ti: remove unwanted THIS_MODULE macroVarka Bhadram
It removes the owner field updation of driver structure. It will be automatically updated by module_platform_driver() Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-08drivers: net: cpsw: Add support for pause framesMugunthan V N
CPSW supports both rx and tx pause frames for flow control. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-05net: ethernet: cpsw: improve interrupt lookup logic in cpsw_probe()Daniel Mack
Simplify the interrupt resource lookup code in cpsw_probe() by the following: * Only look at the first member of the resource. As the driver only works for DT-enabled platforms anyway, a resource of type IORESOURCE_IRQ will only contain one single entry (res->start == res->end), so there is no need for the iteration. * Add a bounds check to avoid overflows if we are passed more than ARRAY_SIZE(priv->irqs_table) resources. * Assign 'ret' with the return value of devm_request_irq() so that cpsw_probe() returns the appropriate error code. * If devm_request_irq() fails, report the error code in the log message. Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Mugunthan V N <mugunthanvnm@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-24drivers: net: cpsw: cleanup: remove unused functionMugunthan V N
removing unused function as part of driver cleanup.` Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-22drivers: net: cpsw: add support to dump ALE table via ethtool register dumpMugunthan V N
Add support to view addresses added by the driver and learnt by the hardware from ALE table via ethtool register dump interface. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-07-15drivers: net: cpsw: disable coalesce when rx_coalesce_usecs is zeroMugunthan V N
instead of return error on zero rx_coalesce_usecs, disable coalesce Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-21drivers: net: cpsw: fix dual EMAC stall when connected to same switchMugunthan V N
In commit 629c9a8fd0bbdfc6d702526b327470166ec39c6b (drivers: net: cpsw: Add default vlan for dual emac case also), api cpsw_add_default_vlan() also changes the port vlan which is required to seperate the ports which results in the following behavior In Dual EMAC mode, when both the Etnernet connected is connected to same switch, it creates a loop in the switch and when a broadcast packet is received it is forwarded to the other port which stalls the whole switch and needs a reset/power cycle to the switch to recover. So intead of using the api, add only the default VLAN entry in dual EMAC case. Cc: Yegor Yefremov <yegorslists@googlemail.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Yegor Yefremov <yegorslists@googlemail.com> Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15ti: Remove trailing semicolon from do {...} while (0) macroJoe Perches
These should not have trailing semicolons so remove them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15driver net: cpsw: Convert pr_*() to dev_*() callsGeorge Cherian
Convert all pr_*() calls to dev_*() calls. No functional changes. Signed-off-by: George Cherian <george.cherian@ti.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13net: get rid of SET_ETHTOOL_OPSWilfried Klaebe
net: get rid of SET_ETHTOOL_OPS Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone. This does that. Mostly done via coccinelle script: @@ struct ethtool_ops *ops; struct net_device *dev; @@ - SET_ETHTOOL_OPS(dev, ops); + dev->ethtool_ops = ops; Compile tested only, but I'd seriously wonder if this broke anything. Suggested-by: Dave Miller <davem@davemloft.net> Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/altera/altera_sgdma.c net/netlink/af_netlink.c net/sched/cls_api.c net/sched/sch_api.c The netlink conflict dealt with moving to netlink_capable() and netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations in non-init namespaces. These were simple transformations from netlink_capable to netlink_ns_capable. The Altera driver conflict was simply code removal overlapping some void pointer cast cleanups in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: cpsw: add missing of_node_putJohan Hovold
Add missing of_node_put to avoid kref leak. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09net: cpsw: fix null dereference at probeJohan Hovold
Fix null-pointer dereference at probe when the mdio platform device is missing (e.g. when it has been disabled in DT). Cc: stable <stable@vger.kernel.org> # v3.8 Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-09Revert "net: eth: cpsw: Correctly attach to GPIO bitbang MDIO driver"Johan Hovold
This reverts commit f8d56d8f892be43a2404356073e16401eb5a42e6 ("net: eth: cpsw: Correctly attach to GPIO bitbang MDIO driver"). Fix potential null-pointer dereference at probe if the mdio-gpio device has not been successfully probed yet. The offending commit is plain wrong for a number of reasons. First of all it accesses internal driver data of an unrelated device. Neither does it check that the data is non-null (which it is in case the device has not been probed yet). Furthermore, the decision on whether to treat any driver data according to the mdio-gpio driver's internals is made based on the node name. But the name is not compared against "mdio" which is the normal name for the node, but rather against "gpio" which the node does not have to be named (and shouldn't be according to the binding documentation). [ If this hack is to be kept out-of-tree it should at least be matching against the compatible property. ] Cc: Stefan Roese <sr@denx.de> Cc: stable <stable@vger.kernel.org> # v3.14 Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05drivers: net: cpsw: Enable Annexe F Time syncGeorge Cherian
Enable the Annex F Time Sync explicitly for DRA7x and AM4372. With this enabled the L2 PTP is working. while at that rename TS_BIT8 to TS_TTL_NONZERO Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-05drivers: net: cpsw: Enable CPTS for DRA7xx and AM4372George Cherian
Enable cpts hardware time stamping for Dra7xx and AM4372. This enables PTPv2 for DRA7xx and AM4372. Signed-off-by: George Cherian <george.cherian@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-11drivers: net: cpsw: enable interrupts after napi enable and clearing ↵Mugunthan V N
previous interrupts When the Ethernet interface is put down and up with heavy Ethernet traffic, then there is prossibility of an interrupt waiting in irq controller to be processed, so when the interface is brought up again just after enable interrupt, it goes to ISR due to the previous unhandled interrutp and in ISR napi is not scheduled as the napi is not enabled in ndo_open which results in disabled interrupt for CPSW and no packets are received in cpsw. So this patch moves enabling of interupts after napi_enable and clearing CPDMA interrupts. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-11drivers: net: cpsw: discard all packets received when interface is downMugunthan V N
When the Ethernet interface is brought down during high Ethernet traffic, then cpsw creates the following warn dump. When cpdma has already processed the packet then the status will be greater than 0, so the cpsw_rx_handler considers that the interface is up and try to resubmit one more rx buffer to cpdma which fails as the DMA is in teardown process. This can be avoided by checking the interface state and then process the received packet, if the interface is down just discard and free the skb and return. [ 2823.104591] WARNING: CPU: 0 PID: 1823 at drivers/net/ethernet/ti/cpsw.c:711 cpsw_rx_handler+0x148/0x164() [ 2823.114654] Modules linked in: [ 2823.117872] CPU: 0 PID: 1823 Comm: ifconfig Tainted: G W 3.14.0-11992-gf34c4a3 #11 [ 2823.126860] [<c0014b5c>] (unwind_backtrace) from [<c00117e4>] (show_stack+0x10/0x14) [ 2823.135030] [<c00117e4>] (show_stack) from [<c0533a9c>] (dump_stack+0x80/0x9c) [ 2823.142619] [<c0533a9c>] (dump_stack) from [<c003f0e0>] (warn_slowpath_common+0x6c/0x90) [ 2823.151141] [<c003f0e0>] (warn_slowpath_common) from [<c003f120>] (warn_slowpath_null+0x1c/0x24) [ 2823.160336] [<c003f120>] (warn_slowpath_null) from [<c03caeb0>] (cpsw_rx_handler+0x148/0x164) [ 2823.169314] [<c03caeb0>] (cpsw_rx_handler) from [<c03c730c>] (__cpdma_chan_free+0x90/0xa8) [ 2823.178028] [<c03c730c>] (__cpdma_chan_free) from [<c03c7418>] (__cpdma_chan_process+0xf4/0x134) [ 2823.187279] [<c03c7418>] (__cpdma_chan_process) from [<c03c7560>] (cpdma_chan_stop+0xb4/0x17c) [ 2823.196349] [<c03c7560>] (cpdma_chan_stop) from [<c03c766c>] (cpdma_ctlr_stop+0x44/0x9c) [ 2823.204872] [<c03c766c>] (cpdma_ctlr_stop) from [<c03cb708>] (cpsw_ndo_stop+0x154/0x188) [ 2823.213321] [<c03cb708>] (cpsw_ndo_stop) from [<c046f0ec>] (__dev_close_many+0x84/0xc8) [ 2823.221761] [<c046f0ec>] (__dev_close_many) from [<c046f158>] (__dev_close+0x28/0x3c) [ 2823.230012] [<c046f158>] (__dev_close) from [<c0474ca8>] (__dev_change_flags+0x88/0x160) [ 2823.238483] [<c0474ca8>] (__dev_change_flags) from [<c0474da0>] (dev_change_flags+0x18/0x48) [ 2823.247316] [<c0474da0>] (dev_change_flags) from [<c04d12c4>] (devinet_ioctl+0x61c/0x6e0) [ 2823.255884] [<c04d12c4>] (devinet_ioctl) from [<c045c660>] (sock_ioctl+0x68/0x2a4) [ 2823.263789] [<c045c660>] (sock_ioctl) from [<c0125fe4>] (do_vfs_ioctl+0x78/0x61c) [ 2823.271629] [<c0125fe4>] (do_vfs_ioctl) from [<c01265ec>] (SyS_ioctl+0x64/0x74) [ 2823.279284] [<c01265ec>] (SyS_ioctl) from [<c000e580>] (ret_fast_syscall+0x0/0x48) Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 13:04:53 +0000