| Age | Commit message (Collapse) | Author |
|---|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to duplicate the same function in rx handler to get info
if any interface is running.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to create additional vars to identify if interface is running.
So simplify code by removing redundant var and checking usage counter
instead.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to set number of descs close to possible values. In case of
minimum limit it's equal to number of channels to be able to set
at least one desc per channel. For maximum limit leave enough descs
number for tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPDMA uses one pool of descriptors for both RX and TX which by default
split between all channels proportionally depending on total number of
CPDMA channels and number of TX and RX channels. As result, more
descriptors will be consumed by TX path if there are more TX channels and
there is no way now to dedicate more descriptors for RX path.
So, add the ability to re-split CPDMA pool of descriptors between RX and TX
path via ethtool '-G' command wich will allow to configure and fix number
of descriptors used by RX and TX path, which, then, will be split between
RX/TX channels proportionally depending on RX/TX channels number and
weight. ethtool '-G' command will accept only number of RX entries and rest
of descriptors will be arranged for TX automatically.
Command:
ethtool -G <devname> rx <number of descriptors>
defaults and limitations:
- minimum number of rx descriptors is 10% of total number of descriptors in
CPDMA pool
- maximum number of rx descriptors is 90% of total number of descriptors in
CPDMA pool
- by default, descriptors will be split equally between RX/TX path
- any values passed in "tx" parameter will be ignored
Usage:
# ethtool -g eth0
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 4096
RX Mini: 0
RX Jumbo: 0
TX: 4096
# ethtool -G eth0 rx 7372
# ethtool -g eth0
Ring parameters for eth0:
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 820
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPSW CPDMA can process buffer descriptors placed as in internal
CPPI RAM as in DDR. This patch adds support in CPSW and CPDMA for
descs_pool_size mudule parameter, which defines total number of CPDMA CPPI
descriptors to be used for both ingress/egress packets processing:
- memory size, required for CPDMA descriptor pool, is calculated basing
on number of descriptors specified by user in descs_pool_size and
CPDMA descriptor size and allocated from coherent memory (CMA area);
- CPDMA descriptor pool will be allocated in DDR if pool memory size >
internal CPPI RAM or use internal CPPI RAM otherwise;
- if descs_pool_size not specified in DT - the default value 256 will
be used which will allow to place CPDMA descriptors pool into the
internal CPPI RAM (current default behaviour);
- CPDMA will ignore descs_pool_size if descs_pool_size = 0 for
backward comaptiobility with davinci_emac.
descs_pool_size is boot time setting and can't be changed once
CPSW/CPDMA is initialized.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.
Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The budget split function requires the phy speed to be known.
While ndo open a phy speed identification is postponed till the
moment link is up. Hence, move it to appropriate callback, when link
is up.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: 8feb0a196507 ("net: ethernet: ti: cpsw: split tx budget according between channels")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netif_set_real_num_tx/rx_queues() are required to be called with rtnl_lock
taken, otherwise ASSERT_RTNL() warning will be triggered - which happens
now during System resume from suspend:
cpsw_resume()
|- cpsw_ndo_open()
|- netif_set_real_num_tx/rx_queues()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_open() by rtnl_lock/unlock() calls.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: commit e05107e6b747 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split device budget between channels according to channel rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check budget fullness only after it's updated and update
channel mask only once to keep budget balance between channels.
It's also needed for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows to rate limit queues tx queues for cpsw interface.
The rate is set in absolute Mb/s units and cannot be more a speed
an interface is connected with.
The rate for a tx queue can be tested with:
ethtool -L eth0 rx 4 tx 4
echo 100 > /sys/class/net/eth0/queues/tx-0/tx_maxrate
echo 200 > /sys/class/net/eth0/queues/tx-1/tx_maxrate
echo 50 > /sys/class/net/eth0/queues/tx-2/tx_maxrate
echo 30 > /sys/class/net/eth0/queues/tx-3/tx_maxrate
tc qdisc add dev eth0 root handle 1: multiq
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5001 0xffff action skbedit queue_mapping 0
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5002 0xffff action skbedit queue_mapping 1
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5003 0xffff action skbedit queue_mapping 2
tc filter add dev eth0 parent 1: protocol ip prio 1 u32 match ip\
dport 5004 0xffff action skbedit queue_mapping 3
iperf -c 192.168.2.1 -b 110M -p 5001 -f m -t 60
iperf -c 192.168.2.1 -b 215M -p 5002 -f m -t 60
iperf -c 192.168.2.1 -b 55M -p 5003 -f m -t 60
iperf -c 192.168.2.1 -b 32M -p 5004 -f m -t 60
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for ethtool's '-r' command. Restarting
N-WAY negotiation can be useful to activate newly changed EEE
settings etc.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ability to query and set Energy Efficient Ethernet parameters
via ethtool for applicable devices.
This patch doesn't activate full EEE support in cpsw driver, but it
enables reading and writing EEE advertising settings. This way one
can disable advertising EEE for certain speeds.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to propagate errors from of_phy_register_fixed_link() which
can fail with -EPROBE_DEFER.
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to check for allocation failures before dereferencing a
NULL-pointer during probe.
Fixes: 649a1688c960 ("net: ethernet: ti: cpsw: create common struct to
hold shared driver data")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister the primary device in case the secondary emac
fails to probe.
kernel BUG at /home/johan/work/omicron/src/linux/net/core/dev.c:7743!
...
[<c05b3dec>] (free_netdev) from [<c04fe6c0>] (cpsw_probe+0x9cc/0xe50)
[<c04fe6c0>] (cpsw_probe) from [<c047b28c>] (platform_drv_probe+0x5c/0xc0)
Fixes: d9ba8f9e6298 ("driver: net: ethernet: cpsw: dual emac interface
implementation")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop references taken and deregister devices registered
during probe on probe errors (including deferred probe) and driver
unbind.
Specifically, PHY of-node references were never released and fixed-link
PHY devices were never deregistered.
Fixes: 9e42f715264f ("drivers: net: cpsw: add phy-handle parsing")
Fixes: 1f71e8c96fc6 ("drivers: net: cpsw: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to deregister all child devices also on probe errors to avoid
leaks and to fix probe deferral:
cpsw 4a100000.ethernet: omap_device: omap_device_enable() called from invalid state 1
cpsw 4a100000.ethernet: use pm_runtime_put_sync_suspend() in driver?
cpsw: probe of 4a100000.ethernet failed with error -22
Add generic helper to undo the effects of cpsw_probe_dt(), which will
also be used in a follow-on patch to fix further leaks that have been
introduced more recently.
Note that the platform device is now runtime-resumed before registering
any child devices in order to make sure that it is synchronously
suspended after having deregistered the children in the error path.
Fixes: 1fb19aa730e4 ("net: cpsw: Add parent<->child relation support
between cpsw and mdio")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by of_find_device_by_node() when
looking up an mdio device from a phy_id property during probe.
Fixes: 549985ee9c72 ("cpsw: simplify the setup of the register
pointers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to keep the platform device runtime-resumed throughout probe
to avoid accessing the CPSW registers in the error path (e.g. for
deferred probe) with clocks disabled:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0872d08
...
[<c04fabcc>] (cpsw_ale_control_set) from [<c04fb8b4>] (cpsw_ale_destroy+0x2c/0x44)
[<c04fb8b4>] (cpsw_ale_destroy) from [<c04fea58>] (cpsw_probe+0xbd0/0x10c4)
[<c04fea58>] (cpsw_probe) from [<c047b2a0>] (platform_drv_probe+0x5c/0xc0)
Fixes: df828598a755 ("netdev: driver: ethernet: Add TI CPSW driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma ctlr is reseted to 0 while cpdma soft reset, thus cpdma ctlr
cannot be configured after cpdma is stopped. So restoring content
of cpdma ctlr while off/on procedure is needed. The cpdma ctlr off/on
procedure is present while interface down/up and while changing number
of channels with ethtool. In order to not restore content in many
places, move it to cpdma_ctlr_start().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the cpsw_fill_rx_channels()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ce52c744574b ("net: ethernet: ti: cpsw: add ethtool channels support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.
How many channels are supported and enabled:
$ ethtool -l ethX
Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6
Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
internals
Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
