| Age | Commit message (Collapse) | Author |
|---|
|
On the Arria10, Agilex, and Stratix10 SoC, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Thus, this patch creates a separate function for setting the phy modes on
Arria10/Agilex/Stratix10. The separation is based a new DTS binding:
"altr,socfpga-stmmac-a10-s10".
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the default value of tx-frames is 25, it's too late when
passing tstamp to stack, then the ptp4l will fail:
ptp4l -i eth0 -f gPTP.cfg -m
ptp4l: selected /dev/ptp0 as PTP clock
ptp4l: port 1: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 0: INITIALIZING to LISTENING on INITIALIZE
ptp4l: port 1: link up
ptp4l: timed out while polling for tx timestamp
ptp4l: increasing tx_timestamp_timeout may correct this issue,
but it is likely caused by a driver bug
ptp4l: port 1: send peer delay response failed
ptp4l: port 1: LISTENING to FAULTY on FAULT_DETECTED (FT_UNSPECIFIED)
ptp4l tests pass when changing the tx-frames from 25 to 1 with
ethtool -C option.
It should be fine to set tx-frames default value to 1, so ptp4l will pass
by default.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
disable rx watchdog for dwmac-mediatek, then the hw will
issue a rx interrupt once receiving a packet, so the responding time
for rx path will be reduced.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add Ethernet power on/off operations in init/exit flow.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope [that] it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 57 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.515993066@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add option for enabling RMII phy mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wei Liang Lim <wei.liang.lim@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
|
|
Pull networking fixes from David Miller:
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
|
|
kfree_skb() shall be used instead of kfree(). Fix it.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable shall be __be16. Fix it.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of devm_alloc_etherdev_mqs() to simplify the code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix gcc build error while CONFIG_INET is not set
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.o: In function `__stmmac_test_loopback':
stmmac_selftests.c:(.text+0x8ec): undefined reference to `ip_send_check'
stmmac_selftests.c:(.text+0xacc): undefined reference to `udp4_hwcsum'
Add CONFIG_INET dependency to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the netdev is registered, calling netdev_info() will emit
something as "(unnamed net device) (uninitialized)", looks confusing.
Before this patch:
[ 3.155028] stmmaceth f7b60000.ethernet (unnamed net_device) (uninitialized): device MAC address 52:1a:55:18:9e:9d
After this patch:
[ 3.155028] stmmaceth f7b60000.ethernet: device MAC address 52:1a:55:18:9e:9d
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the subdriver defers probe, do not show an error message. It's
perfectly fine for this error to occur since the driver will get another
chance to probe after some time and will usually succeed after all of
the resources that it requires have been registered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. the frequency of csr clock is 66.5MHz, so the csr_clk value should
be 0 other than 5.
2. the csr_clk can be got from device tree, so remove initialization here.
Fixes: 9992f37e346b ("stmmac: dwmac-mediatek: add support for mt2712")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specific clk_csr value can be zero, and
stmmac_clk is necessary for MDC clock which can be set dynamically.
So, change the condition from plat->clk_csr to plat->stmmac_clk to
fix clk_csr can't be zero issue.
Fixes: cd7201f477b9 ("stmmac: MDC clock dynamically based on the csr clock input")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we will not update the receive descriptor tail pointer in
stmmac_rx_refill. Rx dma will think no available descriptors and stop
once received packets exceed DMA_RX_SIZE, so that the rx only test will fail.
Update the receive tail pointer in stmmac_rx_refill to add more descriptors
to the rx channel, so packets can be received continually
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
|
|
When we trigger NAPI we are disabling interrupts but in case we receive
or send a packet in the meantime, as interrupts are disabled, we will
miss this event.
Trigger both NAPI instances (RX and TX) when at least one event happens
so that we don't miss any interrupts.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.
This is also needed for stmmac Flow Control selftest.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need to disable the whole RX when dma_stop_rx() is called
because there may be the need of just disabling 1 DMA channel.
This is also needed for stmmac Flow Control selftest.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for hash filter to work we need to set the HPF bit.
Fout out while running stmmac selftests
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we don't use a given address entry we need to clear it because
it could contain previous values that are no longer valid.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for hash filter to work we need to set the HPF bit.
Found out while running stmmac selftests.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We add support for selftests on stmmac driver with 9 basic sanity checks
for now:
- MAC Loopback
- PHY Loopback
- MMC Counters
- EEE
- Hash Filter Multicast
- Perfect Filter Unicast
- Multicast Filter All
- Unicast Filter All
- Flow Control
This allows for fast tracking of regressions in the driver and helps in
spotting mis-configuration of HW.
Changes from v1:
- Fix build error as module (David)
- Check for link status before running tests
Changes from RFC v2:
- Return proper error code in stmmac_test_mmc (Corentin)
- Use only 1 MMC counter in stmmac_test_mmc (Alexandre)
Changes from RFC v1:
- Change test_loopback to test_mac_loopback (Andrew)
- Change timeout to retries (Andrew)
- Add MC/UC filter tests (Andrew)
- Only test in offline mode (Andrew)
- Do not call phy_loopback twice (Alexandre)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the selftests to run the Flow Control selftest we need to
also pass pause frames to the stack.
Pass this type of frames while in promiscuous mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XGMAC has a different MMC module. Lets use HWIF callbacks for MMC module
so that correct callbacks are automatically selected.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enable use of set_mac_loopback in dwmac-sun8i
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwxgmac2 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac4/5 cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac1000 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the addition of stmmac selftests we implement the MAC
loopback callback in dwmac100 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the addition of selftests support for stmmac we add a
new callback to HWIF that can be used to set the controller in loopback
mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
licensed under the gplv2 or at your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091651.323272658@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
removed the reset gpio free, when the driver is unbinded or rmmod,
we miss the gpio free.
This patch uses managed API to request the reset gpio, so that the
gpio could be freed properly.
Fixes: 984203ceff27 ("net: stmmac: mdio: remove reset gpio free")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
stmmac_init_chan() needs to be called before stmmac_init_rx_chan() and
stmmac_init_tx_chan(). This is because if PBLx8 is to be used,
"DMA_CH(#i)_Control.PBLx8" needs to be set before programming
"DMA_CH(#i)_TX_Control.TxPBL" and "DMA_CH(#i)_RX_Control.RxPBL".
Fixes: 47f2a9ce527a ("net: stmmac: dma channel init prepared for multiple queues")
Reviewed-by: Zhang, Baoli <baoli.zhang@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Weifeng Voon <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
