| Age | Commit message (Collapse) | Author |
|---|
|
sa8775p-ride-r3
[ Upstream commit 3c466d6537b99f801b3f68af3d8124d4312437a0 ]
On sa8775p-ride-r3 the RX clocks from the AQR115C PHY are not available at
the time of the DMA reset. We can however extract the RX clock from the
internal SERDES block. Once the link is up, we can revert to the
previous state.
The AQR115C PHY doesn't support in-band signalling so we can count on
getting the link up notification and safely reuse existing callbacks
which are already used by another HW quirk workaround which enables the
functional clock to avoid a DMA reset due to timeout.
Only enable loopback on revision 3 of the board - check the phy_mode to
make sure.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240703181500.28491-3-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9dbebae2e3c338122716914fe105458f41e3a4a ]
The perfect_match parameter of the update_vlan_hash operation is __le16,
and is correctly converted from host byte-order in the lone caller,
stmmac_vlan_update().
However, the implementations of this caller, dwxgmac2_update_vlan_hash()
and dwxgmac2_update_vlan_hash(), both treat this parameter as host byte
order, using the following pattern:
u32 value = ...
...
writel(value | perfect_match, ...);
This is not correct because both:
1) value is host byte order; and
2) writel expects a host byte order value as it's first argument
I believe that this will break on big endian systems. And I expect it
has gone unnoticed by only being exercised on little endian systems.
The approach taken by this patch is to update the callback, and it's
caller to simply use a host byte order value.
Flagged by Sparse.
Compile tested only.
Fixes: c7ab0b8088d7 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b698ab56837bc9e666b7e7e12e9c28fe1d6a763c upstream.
Correct member @num_por with size of right array @emac_v4_0_0_por for
struct ethqos_emac_driver_data @emac_v4_0_0_data.
Cc: stable@vger.kernel.org
Fixes: 8c4d92e82d50 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20240701014720.2547856-1-quic_yijiyang@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8851346912a1fa33e7a5966fe51f07313b274627 upstream.
Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529da60 ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b8c43360f6e424131fa81d3ba8792ad8ff25a09e ]
commit be27b8965297 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b8965297 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
parameters
[ Upstream commit be27b896529787e23a35ae4befb6337ce73fcca0 ]
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0579f27249047006a818e463ee66a6c314d04cea ]
Commit 070246e4674b ("net: stmmac: Fix for mismatched host/device DMA
address width") added support in the stmmac driver for platform drivers
to indicate the host DMA width, but left it up to authors of the
specific platforms to indicate if their width differed from the addr64
register read from the MAC itself.
Qualcomm's EMAC4 integration supports only up to 36 bit width (as
opposed to the addr64 register indicating 40 bit width). Let's indicate
that in the platform driver to avoid a scenario where the driver will
allocate descriptors of size that is supported by the CPU which in our
case is 36 bit, but as the addr64 register is still capable of 40 bits
the device will use two descriptors as one address.
Fixes: 8c4d92e82d50 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Sagar Cheluvegowda <quic_scheluve@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9cb54af214a7cdc91577ec083e5569f2ce2c86d8 ]
Here is the list of the MAC capabilities specific to the particular DW MAC
IP-cores currently supported by the driver:
DW MAC100: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100
DW GMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
Allwinner sun8i MAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000
DW QoS Eth: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10 | MAC_100 | MAC_1000 | MAC_2500FD
if there is more than 1 active Tx/Rx queues:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_10FD | MAC_100FD | MAC_1000FD | MAC_2500FD
DW XGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD
DW XLGMAC: MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
MAC_1000FD | MAC_2500FD | MAC_5000FD | MAC_10000FD |
MAC_25000FD | MAC_40000FD | MAC_50000FD | MAC_100000FD
As you can see there are only two common capabilities:
MAC_ASYM_PAUSE | MAC_SYM_PAUSE.
Meanwhile what is currently implemented defines 10/100/1000 link speeds
for all IP-cores, which is definitely incorrect for DW MAC100, DW XGMAC
and DW XLGMAC devices.
Seeing the flow-control is implemented as a callback for each MAC IP-core
(see dwmac100_flow_ctrl(), dwmac1000_flow_ctrl(), sun8i_dwmac_flow_ctrl(),
etc) and since the MAC-specific setup() method is supposed to be called
for each available DW MAC-based device, the capabilities initialization
can be freely moved to these setup() functions, thus correctly setting up
the MAC-capabilities for each IP-core (including the Allwinner Sun8i). A
new stmmac_link::caps field was specifically introduced for that so to
have all link-specific info preserved in a single structure.
Note the suggested change fixes three earlier commits at a time. The
commit 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC
supports") permitted the 10-100 link speeds and 1G half-duplex mode for DW
XGMAC IP-core even though it doesn't support them. The commit df7699c70c1b
("net: stmmac: Do not cut down 1G modes") incorrectly added the MAC1000
capability to the DW MAC100 IP-core. Similarly to the DW XGMAC the commit
8a880936e902 ("net: stmmac: Add XLGMII support") incorrectly permitted the
10-100 link speeds and 1G half-duplex mode for DW XLGMAC IP-core.
Fixes: 5b0d7d7da64b ("net: stmmac: Add the missing speeds that XGMAC supports")
Fixes: df7699c70c1b ("net: stmmac: Do not cut down 1G modes")
Fixes: 8a880936e902 ("net: stmmac: Add XLGMII support")
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 59c3d6ca6cbded6c6599e975b42a9d6a27fcbaf2 ]
It's possible to have the maximum link speed being artificially limited on
the platform-specific basis. It's done either by setting up the
plat_stmmacenet_data::max_speed field or by specifying the "max-speed"
DT-property. In such cases it's required that any specific
MAC-capabilities re-initializations would take the limit into account. In
particular the link speed capabilities may change during the number of
active Tx/Rx queues re-initialization. But the currently implemented
procedure doesn't take the speed limit into account.
Fix that by calling phylink_limit_mac_speed() in the
stmmac_reinit_queues() method if the speed limitation was required in the
same way as it's done in the stmmac_phy_setup() function.
Fixes: 95201f36f395 ("net: stmmac: update MAC capabilities when tx queues are updated")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ebd96f5da4410c0cb8fc75e44f1009530b2f90b ]
There are three DW MAC IP-cores which can have the multiple Tx/Rx queues
enabled:
DW GMAC v3.7+ with AV feature,
DW QoS Eth v4.x/v5.x,
DW XGMAC/XLGMAC
Based on the respective HW databooks, only the DW QoS Eth IP-core doesn't
support the half-duplex link mode in case if more than one queues enabled:
"In multiple queue/channel configurations, for half-duplex operation,
enable only the Q0/CH0 on Tx and Rx. For single queue/channel in
full-duplex operation, any queue/channel can be enabled."
The rest of the IP-cores don't have such constraint. Thus in order to have
the constraint applied for the DW QoS Eth MACs only, let's move the it'
implementation to the respective MAC-capabilities getter and make sure the
getter is called in the queues re-init procedure.
Fixes: b6cfffa7ad92 ("stmmac: fix DMA channel hang in half-duplex mode")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d4597b871210429bda0f5c3a8816b7d9b6daf7e ]
Add a missing quirk to enable support for the StarFive JH7100 SoC.
Additionally, for greater flexibility in operation, allow using the
rgmii-rxid and rgmii-txid phy modes.
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b3da86d432b7cd65b025a11f68613e333d2483db upstream.
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2a7 ("net: stmmac: TX and RX queue priority configuration")
Fixes: 2142754f8b9c ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com>
Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8af411bbba1f457c33734795f024d0ef26d0963f ]
Currently when suspending driver and stopping workqueue it is checked whether
workqueue is not NULL and if so, it is destroyed.
Function destroy_workqueue() does drain queue and does clear variable, but
it does not set workqueue variable to NULL. This can cause kernel/module
panic if code attempts to clear workqueue that was not initialized.
This scenario is possible when resuming suspended driver in stmmac_resume(),
because there is no handling for failed stmmac_hw_setup(),
which can fail and return if DMA engine has failed to initialize,
and workqueue is initialized after DMA engine.
Should DMA engine fail to initialize, resume will proceed normally,
but interface won't work and TX queue will eventually timeout,
causing 'Reset adapter' error.
This then does destroy workqueue during reset process.
And since workqueue is initialized after DMA engine and can be skipped,
it will cause kernel/module panic.
To secure against this possible crash, set workqueue variable to NULL when
destroying workqueue.
Log/backtrace from crash goes as follows:
[88.031977]------------[ cut here ]------------
[88.031985]NETDEV WATCHDOG: eth0 (sxgmac): transmit queue 1 timed out
[88.032017]WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:477 dev_watchdog+0x390/0x398
<Skipping backtrace for watchdog timeout>
[88.032251]---[ end trace e70de432e4d5c2c0 ]---
[88.032282]sxgmac 16d88000.ethernet eth0: Reset adapter.
[88.036359]------------[ cut here ]------------
[88.036519]Call trace:
[88.036523] flush_workqueue+0x3e4/0x430
[88.036528] drain_workqueue+0xc4/0x160
[88.036533] destroy_workqueue+0x40/0x270
[88.036537] stmmac_fpe_stop_wq+0x4c/0x70
[88.036541] stmmac_release+0x278/0x280
[88.036546] __dev_close_many+0xcc/0x158
[88.036551] dev_close_many+0xbc/0x190
[88.036555] dev_close.part.0+0x70/0xc0
[88.036560] dev_close+0x24/0x30
[88.036564] stmmac_service_task+0x110/0x140
[88.036569] process_one_work+0x1d8/0x4a0
[88.036573] worker_thread+0x54/0x408
[88.036578] kthread+0x164/0x170
[88.036583] ret_from_fork+0x10/0x20
[88.036588]---[ end trace e70de432e4d5c2c1 ]---
[88.036597]Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004
Fixes: 5a5586112b929 ("net: stmmac: support FPE link partner hand-shaking procedure")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97dde84026339e4b4af9a6301f825d1828d7874b ]
If 'dev' or 'data' is NULL, the 'priv' variable has an incorrect address
when dereferencing calling netdev_err().
Since we get as 'dev_id' or 'data' what was passed as the 'dev' argument
to request_irq() during interrupt initialization (that is, the net_device
and rx/tx queue pointers initialized at the time of the call) and since
there are usually no checks for the 'dev_id' argument in such handlers
in other drivers, remove these checks from the handlers in stmmac driver.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX")
Signed-off-by: Pavel Sakharov <p.sakharov@ispras.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 38cc3c6dcc09dc3a1800b5ec22aef643ca11eab8 upstream.
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/Za173PhviYg-1qIn@torres.zugschlus.de/t/
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4896bb7c0b31a0a3379b290ea7729900c59e0c69 upstream.
With the dma conf being reallocated on each call to stmmac_open(), any
information in there is lost, unless we specifically handle it.
The STMMAC_TBS_EN bit is set when adding an etf qdisc, and the etf qdisc
therefore would stop working when link was set down and then back up.
Fixes: ba39b344e924 ("net: ethernet: stmicro: stmmac: generate stmmac dma conf before open")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ce2654d87e2fb91fea83b288bd9b2641045e42a upstream.
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1692b9775e745f84b69dc8ad0075b0855a43db4e upstream.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 46eba193d04f8bd717e525eb4110f3c46c12aec3 ]
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a5f5eee282a0aae80227697e1d9c811b1726d31d ]
otherwise the synopsys_id value may be read out wrong,
because the GMAC_VERSION register might still be in reset
state, for at least 1 us after the reset is de-asserted.
Add a wait for 10 us before continuing to be on the safe side.
> From what have you got that delay value?
Just try and error, with very old linux versions and old gcc versions
the synopsys_id was read out correctly most of the time (but not always),
with recent linux versions and recnet gcc versions it was read out
wrongly most of the time, but again not always.
I don't have access to the VHDL code in question, so I cannot
tell why it takes so long to get the correct values, I also do not
have more than a few hardware samples, so I cannot tell how long
this timeout must be in worst case.
Experimentally I can tell that the register is read several times
as zero immediately after the reset is de-asserted, also adding several
no-ops is not enough, adding a printk is enough, also udelay(1) seems to
be enough but I tried that not very often, and I have not access to many
hardware samples to be 100% sure about the necessary delay.
And since the udelay here is only executed once per device instance,
it seems acceptable to delay the boot for 10 us.
BTW: my hardware's synopsys id is 0x37.
Fixes: c5e4ddbdfa11 ("net: stmmac: Add support for optional reset control")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/AS8P193MB1285A810BD78C111E7F6AA34E4752@AS8P193MB1285.EURP193.PROD.OUTLOOK.COM
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2945c435c999c63e47f337bc7c13c98c21d0bcc ]
Some DSA tagging protocols change the EtherType field in the MAC header
e.g. DSA_TAG_PROTO_(DSA/EDSA/BRCM/MTK/RTL4C_A/SJA1105). On TX these tagged
frames are ignored by the checksum offload engine and IP header checker of
some stmmac cores.
On RX, the stmmac driver wrongly assumes that checksums have been computed
for these tagged packets, and sets CHECKSUM_UNNECESSARY.
Add an additional check in the stmmac TX and RX hotpaths so that COE is
deactivated for packets with ethertypes that will not trigger the COE and
IP header checks.
Fixes: 6b2c6e4a938f ("net: stmmac: propagate feature flags to vlan")
Cc: <stable@vger.kernel.org>
Reported-by: Richard Tresidder <rtresidd@electromag.com.au>
Link: https://lore.kernel.org/netdev/e5c6c75f-2dfa-4e50-a1fb-6bf4cdb617c2@electromag.com.au/
Reported-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://lore.kernel.org/netdev/c57283ed-6b9b-b0e6-ee12-5655c1c54495@bootlin.com/
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8452a05b2c633b708dbe3e742f71b24bf21fe42d ]
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c2945c435c99 ("net: stmmac: Prevent DSA tags from breaking COE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
calls
[ Upstream commit a23aa04042187cbde16f470b49d4ad60d32e9206 ]
We found the following dmesg calltrace when testing the GMAC NIC notebook:
[9.448656] ------------[ cut here ]------------
[9.448658] Unbalanced IRQ 43 wake disable
[9.448673] WARNING: CPU: 3 PID: 1083 at kernel/irq/manage.c:688 irq_set_irq_wake+0xe0/0x128
[9.448717] CPU: 3 PID: 1083 Comm: ethtool Tainted: G O 4.19 #1
[9.448773] ...
[9.448774] Call Trace:
[9.448781] [<9000000000209b5c>] show_stack+0x34/0x140
[9.448788] [<9000000000d52700>] dump_stack+0x98/0xd0
[9.448794] [<9000000000228610>] __warn+0xa8/0x120
[9.448797] [<9000000000d2fb60>] report_bug+0x98/0x130
[9.448800] [<900000000020a418>] do_bp+0x248/0x2f0
[9.448805] [<90000000002035f4>] handle_bp_int+0x4c/0x78
[9.448808] [<900000000029ea40>] irq_set_irq_wake+0xe0/0x128
[9.448813] [<9000000000a96a7c>] stmmac_set_wol+0x134/0x150
[9.448819] [<9000000000be6ed0>] dev_ethtool+0x1368/0x2440
[9.448824] [<9000000000c08350>] dev_ioctl+0x1f8/0x3e0
[9.448827] [<9000000000bb2a34>] sock_ioctl+0x2a4/0x450
[9.448832] [<900000000046f044>] do_vfs_ioctl+0xa4/0x738
[9.448834] [<900000000046f778>] ksys_ioctl+0xa0/0xe8
[9.448837] [<900000000046f7d8>] sys_ioctl+0x18/0x28
[9.448840] [<9000000000211ab4>] syscall_common+0x20/0x34
[9.448842] ---[ end trace 40c18d9aec863c3e ]---
Multiple disable_irq_wake() calls will keep decreasing the IRQ
wake_depth, When wake_depth is 0, calling disable_irq_wake() again,
will report the above calltrace.
Due to the need to appear in pairs, we cannot call disable_irq_wake()
without calling enable_irq_wake(). Fix this by making sure there are
no unbalanced disable_irq_wake() calls.
Fixes: 3172d3afa998 ("stmmac: support wake up irq from external sources (v3)")
Signed-off-by: Qiang Ma <maqianga@uniontech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240112021249.24598-1-maqianga@uniontech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 08300adac3b8dab9e2fd3be0155c7d3093c755f4 ]
Currently get/set_link_ksettings ethtool ops are dependent on PCS.
When PCS is integrated, it will not have separate link config.
Bypass configuring and checking PCS for integrated PCS.
Fixes: aa571b6275fb ("net: stmmac: add new switch to struct plat_stmmacenet_data")
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8775p-ride
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 61921bdaa132b580b6db6858e6d7dcdb870df5fe upstream.
Fix per-queue statistics for devices with more than one queue.
The output data pointer is currently reset in each loop iteration,
effectively summing all queue statistics in the first four u64 values.
The summary values are not even labeled correctly. For example, if eth0 has
2 queues, ethtool -S eth0 shows:
q0_tx_pkt_n: 374 (actually tx_pkt_n over all queues)
q0_tx_irq_n: 23 (actually tx_normal_irq_n over all queues)
q1_tx_pkt_n: 462 (actually rx_pkt_n over all queues)
q1_tx_irq_n: 446 (actually rx_normal_irq_n over all queues)
q0_rx_pkt_n: 0
q0_rx_irq_n: 0
q1_rx_pkt_n: 0
q1_rx_irq_n: 0
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31fea092c6f9f8fb2c40a08137907f5fbeae55dd ]
Device binds to proper PCI ID (LOONGSON, 0x7a03), already listed in DTS,
so checking for some other compatible does not make sense. It cannot be
bound to unsupported platform.
Drop useless, incorrect (space in between) and undocumented compatible.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit bd7f77dae69532ffc027ee50ff99e3792dc30b7f upstream.
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7fbd5fc2b35a8f559a6b380dfa9bcd964a758186 ]
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e23c0d21ce9234fbc31ece35663ababbb83f9347 ]
Many hardware configurations have the MDIO bus disabled, and are instead
using some other MDIO bus to talk to the MAC's phy.
of_mdiobus_register() returns -ENODEV in this case. Let's handle it
gracefully instead of failing to probe the MAC.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20231212-b4-stmmac-handle-mdio-enodev-v2-1-600171acf79f@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 981d947bcd382c3950a593690e0e13d194d65b1c ]
In 10M SGMII mode all the packets are being dropped due to wrong Rx clock.
SGMII 10MBPS mode needs RX clock divider programmed to avoid drops in Rx.
Update configure SGMII function with Rx clk divider programming.
Fixes: 463120c31c58 ("net: stmmac: dwmac-qcom-ethqos: add support for SGMII")
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Sneh Shah <quic_snehshah@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20231212092208.22393-1-quic_snehshah@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e87d3a1370ce9f04770d789bcf7cce44865d2e8d ]
Generic code will use mdio. If it is not initialized before use,
the kernel will Oops.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37e4b8df27bc68340f3fc80dbb27e3549c7f881c ]
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e54d628a2721bfbb002c19f6e8ca6746cec7640f ]
Commit aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd07692 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b6cb4541853c7ee512111b0e7ddf3cb66c99c137 ]
dma_rx_size can be set as low as 64. Rx budget might be higher than
that. Make sure to not overrun allocated rx buffers when budget is
larger.
Leave one descriptor unused to avoid wrap around of 'dirty_rx' vs
'cur_rx'.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Link: https://lore.kernel.org/r/d95413e44c97d4692e72cec13a75f894abeb6998.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fa02de9e75889915b554eda1964a631fd019973b ]
The while loop condition verifies 'count < limit'. Neither value change
before the 'count >= limit' check. As is this check is dead code. But
code inspection reveals a code path that modifies 'count' and then goto
'drain_data' and back to 'read_again'. So there is a need to verify
count value sanity after 'read_again'.
Move 'read_again' up to fix the count limit check.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/d9486296c3b6b12ab3a0515fcd47d56447a07bfc.1699897370.git.baruch@tkos.co.il
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit db456d90a4c1b43b6251fa4348c8adc59b583274 ]
From XGMAC Core 3.20 and later, each Flexible PPS has individual PPSEN bit
to select Fixed mode or Flexible mode. The PPSEN must be set, or it stays
in Fixed PPS mode by default.
XGMAC Core prior 3.20, only PPSEN0(bit 4) is writable. PPSEN{1,2,3} are
read-only reserved, and they are already in Flexible mode by default, our
new code always set PPSEN{1,2,3} do not make things worse ;-)
Fixes: 95eaf3cd0a90 ("net: stmmac: dwxgmac: Add Flexible PPS support")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Upon boot up, the driver will configure the MAC capabilities based on
the maximum number of tx and rx queues. When the user changes the
tx queues to single queue, the MAC should be capable of supporting Half
Duplex, but the driver does not update the MAC capabilities when it is
configured so.
Using the stmmac_reinit_queues() to check the number of tx queues
and set the MAC capabilities accordingly.
Fixes: 0366f7e06a6b ("net: stmmac: add ethtool support for get/set channels")
Cc: <stable@vger.kernel.org> # 5.17+
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Gan, Yi Fang <yi.fang.gan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034e5 ("netpoll: make ndo_poll_controller() optional")
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The second parameter of stmmac_pltfr_init() needs the pointer of
"struct plat_stmmacenet_data". So, correct the parameter typo when calling the
function.
Otherwise, it may cause this alignment exception when doing suspend/resume.
[ 49.067201] CPU1 is up
[ 49.135258] Internal error: SP/PC alignment exception: 000000008a000000 [#1] PREEMPT SMP
[ 49.143346] Modules linked in: soc_imx9 crct10dif_ce polyval_ce nvmem_imx_ocotp_fsb_s400 polyval_generic layerscape_edac_mod snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_imx_card snd_soc_wm8962 el_enclave snd_soc_fsl_micfil rtc_pcf2127 rtc_pcf2131 flexcan can_dev snd_soc_fsl_xcvr snd_soc_fsl_sai imx8_media_dev(C) snd_soc_fsl_utils fuse
[ 49.173393] CPU: 0 PID: 565 Comm: sh Tainted: G C 6.5.0-rc4-next-20230804-05047-g5781a6249dae #677
[ 49.183721] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[ 49.189190] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 49.196140] pc : 0x80800052
[ 49.198931] lr : stmmac_pltfr_resume+0x34/0x50
[ 49.203368] sp : ffff800082f8bab0
[ 49.206670] x29: ffff800082f8bab0 x28: ffff0000047d0ec0 x27: ffff80008186c170
[ 49.213794] x26: 0000000b5e4ff1ba x25: ffff800081e5fa74 x24: 0000000000000010
[ 49.220918] x23: ffff800081fe0000 x22: 0000000000000000 x21: 0000000000000000
[ 49.228042] x20: ffff0000001b4010 x19: ffff0000001b4010 x18: 0000000000000006
[ 49.235166] x17: ffff7ffffe007000 x16: ffff800080000000 x15: 0000000000000000
[ 49.242290] x14: 00000000000000fc x13: 0000000000000000 x12: 0000000000000000
[ 49.249414] x11: 0000000000000001 x10: 0000000000000a60 x9 : ffff800082f8b8c0
[ 49.256538] x8 : 0000000000000008 x7 : 0000000000000001 x6 : 000000005f54a200
[ 49.263662] x5 : 0000000001000000 x4 : ffff800081b93680 x3 : ffff800081519be0
[ 49.270786] x2 : 0000000080800052 x1 : 0000000000000000 x0 : ffff0000001b4000
[ 49.277911] Call trace:
[ 49.280346] 0x80800052
[ 49.282781] platform_pm_resume+0x2c/0x68
[ 49.286785] dpm_run_callback.constprop.0+0x74/0x134
[ 49.291742] device_resume+0x88/0x194
[ 49.295391] dpm_resume+0x10c/0x230
[ 49.298866] dpm_resume_end+0x18/0x30
[ 49.302515] suspend_devices_and_enter+0x2b8/0x624
[ 49.307299] pm_suspend+0x1fc/0x348
[ 49.310774] state_store+0x80/0x104
[ 49.314258] kobj_attr_store+0x18/0x2c
[ 49.318002] sysfs_kf_write+0x44/0x54
[ 49.321659] kernfs_fop_write_iter+0x120/0x1ec
[ 49.326088] vfs_write+0x1bc/0x300
[ 49.329485] ksys_write+0x70/0x104
[ 49.332874] __arm64_sys_write+0x1c/0x28
[ 49.336783] invoke_syscall+0x48/0x114
[ 49.340527] el0_svc_common.constprop.0+0xc4/0xe4
[ 49.345224] do_el0_svc+0x38/0x98
[ 49.348526] el0_svc+0x2c/0x84
[ 49.351568] el0t_64_sync_handler+0x100/0x12c
[ 49.355910] el0t_64_sync+0x190/0x194
[ 49.359567] Code: ???????? ???????? ???????? ???????? (????????)
[ 49.365644] ---[ end trace 0000000000000000 ]---
Fixes: 97117eb51ec8 ("net: stmmac: platform: provide stmmac_pltfr_init()")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics
where necessary") caused one regression as found by Uwe, the backtrace
looks like:
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.5.0-rc1-00449-g133466c3bbe1-dirty #21
Hardware name: STM32 (Device Tree Support)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x60/0x90
dump_stack_lvl from register_lock_class+0x98c/0x99c
register_lock_class from __lock_acquire+0x74/0x293c
__lock_acquire from lock_acquire+0x134/0x398
lock_acquire from stmmac_get_stats64+0x2ac/0x2fc
stmmac_get_stats64 from dev_get_stats+0x44/0x130
dev_get_stats from rtnl_fill_stats+0x38/0x120
rtnl_fill_stats from rtnl_fill_ifinfo+0x834/0x17f4
rtnl_fill_ifinfo from rtmsg_ifinfo_build_skb+0xc0/0x144
rtmsg_ifinfo_build_skb from rtmsg_ifinfo+0x50/0x88
rtmsg_ifinfo from __dev_notify_flags+0xc0/0xec
__dev_notify_flags from dev_change_flags+0x50/0x5c
dev_change_flags from ip_auto_config+0x2f4/0x1260
ip_auto_config from do_one_initcall+0x70/0x35c
do_one_initcall from kernel_init_freeable+0x2ac/0x308
kernel_init_freeable from kernel_init+0x1c/0x138
kernel_init from ret_from_fork+0x14/0x2c
The reason is the rxq|txq_stats structures are not what expected
because stmmac_open() -> __stmmac_open() the structure is overwritten
by "memcpy(&priv->dma_conf, dma_conf, sizeof(*dma_conf));"
This causes the well initialized syncp member of rxq|txq_stats is
overwritten unexpectedly as pointed out by Johannes and Uwe.
Fix this issue by moving rxq|txq_stats back to stmmac_extra_stats. For
SMP cache friendly, we also mark stmmac_txq_stats and stmmac_rxq_stats
as ____cacheline_aligned_in_smp.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917165328.3403-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce33317023 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Stein reports that commit a014c35556b9 ("net: stmmac: clarify
difference between "interface" and "phy_interface"") caused breakage,
because plat->mac_interface will never be negative. Fix this by using
the "rc" temporary variable in stmmac_probe_config_dt().
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/E1qayn0-006Q8J-GE@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clarify the difference between "interface" and "phy_interface" in
struct plat_stmmacenet_data, both by adding a comment, and also
renaming "interface" to be "mac_interface". The difference between
these are:
MAC ----- optional PCS ----- SerDes ----- optional PHY ----- Media
^ ^
mac_interface phy_interface
Note that phylink currently only deals with phy_interface.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZq83-005tts-6K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rather than detecting when half-duplex is not supported, and clearing
the MAC capabilities, reverse the if() condition and use it to set the
capabilities instead.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXn-005pUb-SP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move priv->phylink_config.mac_managed_pm to be along side the other
phylink initialisations.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXi-005pUV-Nq@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the xgmac specific phylink capabilities to the dwxgmac2 support
core.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXd-005pUP-JL@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the setup of gmac4 speicifc phylink capabilities into gmac4 code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXY-005pUJ-Ez@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow MACs to provide their own capabilities via the MAC operations
struct.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXT-005pUD-Aj@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_limit_mac_speed() to limit the MAC capabilities rather
than coding this for each speed.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAXO-005pU7-61@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
