| Age | Commit message (Collapse) | Author |
|---|
|
Malicious VF existance should be interesting enough for the
hyperuser. Change the PF indication that one of its child VF
became malicious to appear by default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PF<->VF interface allows for the VF to request
multiple queues closure via a single message, but this has
never been used by any official driver.
We now deprecate this option, forcing each queue close
to arrive via a different command; This would be required
for future TLVs that are going to extend the queue TLVs with
additional information on a per-queue basis.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF needs to validate the status of VF queues before asking firmware
to configure anything for them, but that validation is done in various
different forms - sometimes inadequate.
Add auxillary functions that can be used for testing of the queue
state and convert the various flows to use those instead of current
existing flows; Also, add missing validations where needed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When starting the VF's vport, the PF would first configure
the status blocks of the VF and then reset them.
That would cause some of the configured information to be lost -
specifically it would mean that all the VFs queues would use
the Rx coalescing state-machine of the status block.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PF responds to the VF requests it also cleans the HW-channel
indication in firmware to allow further VF messages to arrive,
but the order currently applied is wrong -
The PF is copying by DMAE the response the VF is polling on for
completion, and only afterwards sets the HW-channel to ready state.
This creates a race condition where the VF would be able to send
an additional message to the PF before the channel would get ready
again, causing the firmware to consider the VF as malicious.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a VF is considered malicious, driver handling of the VF
FLR flow would clean said indication - but not if the FLR is
part of an sriov-disable flow.
That leads to further issues, as PF wouldn't re-enable the
previously malicious VF when sriov is re-enabled.
No reason for that - simply clean malicious indications in
the sriov-disable flow as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VFs are currently logging errors when communicating
with their PFs in a too-low verbosity that wouldn't
be shown by default. As timeouts and failed commands
are crucial for VF operability, make them appear by
default.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca43 ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb50 ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.
It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.
In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].
Changes from Previous versions:
-------------------------------
- V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In qed_ll2_start_ooo() the ll2_info variable is uninitialized and then
passed to qed_ll2_acquire_connection() where it is copied into a new
memory space.
This shouldn't cause any issue as long as non of the copied memory is
every read.
But the potential for a bug being introduced by reading this memory
is real.
Detected by CoverityScan, CID#1399632 ("Uninitialized scalar variable")
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 653d2ffd6405 ("qed*: Fix link indication race") introduced another
race - one of the inner functions called from the link-change flow is
explicitly using the slowpath context dedicated PTT instead of gaining
that PTT from the caller. Since this flow can now be called from
a different context as well, we're in risk of the PTT breaking.
Fixes: 653d2ffd6405 ("qed*: Fix link indication race")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A PF syncronizes all IOV activity relating to its VFs
by using a single workqueue handling the work.
The workqueue would reach a bitmask of pending VF events
and act upon each in turn.
Problem is that the indication of a VF message [which sets
the 'vf event' bit for that VF] arrives and is set in
the slowpath attention context, which isn't syncronized with
the processing of the events.
When multiple VFs are present, it's possible that PF would
lose the indication of one of the VF's pending evens, leading
that VF to later timeout.
Instead of adding locks/barriers, simply move from a bitmask
into a per-VF indication inside that VF entry in the PF database.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver changes the link properties via communication with
the management firmware, and re-reads the resulting link status
when it receives an indication that the link has changed.
However, there are certain scenarios where such indications
might be missing, and so driver also re-reads the current link
results without attention in several places. Specifically, it
does so during load and when resetting the link.
This creates a race where driver might reflect incorrect
link status - e.g., when explicit reading of the link status is
switched by attention with the changed configuration.
Correct this flow by a lock syncronizing the handling of the
link indications [both explicit requests and attention].
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flows accessing registers require the flow to hold a PTT entry.
To protect 'major' load/unload flows a main_ptt is pre-allocated
to guarantee such flows wouldn't be blocked by PTT being
unavailable.
Status block initialization currently uses the main_ptt which
is incorrect, as this flow might run concurrently to others
[E.g., loading qedr while toggling qede]. That would have dire
effects as it means registers' access to device breaks and further
read/writes might access incorrect addresses.
Instead, when initializing status blocks acquire/release a PTT
as part of the flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.
Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If QP is in reset state then there are no resources to free so avoid
freeing any.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CQ resource pool is protected by a spin lock. When a CQ creation
fails it now deallocates under that lock as well.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two trivial overlapping changes conflicts in MPLS and mlx5.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct qed_ll2_info is rather large, so putting it on the stack
can cause an overflow, as this warning tries to tell us:
drivers/net/ethernet/qlogic/qed/qed_ll2.c: In function 'qed_ll2_start':
drivers/net/ethernet/qlogic/qed/qed_ll2.c:2159:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
qed_ll2_start_ooo() already uses a dynamic allocation for the structure
to work around that problem, and we could do the same in qed_ll2_start()
as well as qed_roce_ll2_start(), but since the structure is only
used to pass a couple of initialization values here, it seems nicer
to replace it with a different structure.
Lacking any idea for better naming, I'm adding 'struct qed_ll2_conn',
which now contains all the initialization data, and this now simply
gets copied into struct qed_ll2_info rather than assigning all members
one by one.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If qedr isn't part of the kernel then don't allocate RDMA resources
for it in qed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently multicast traffic wouldn't be routed internally to
listener; Instead it would only be sent to network via the
physical carrier.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trusted VFs would be allowed to receive promiscuous and
multicast promiscuous data.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Today qede requests contexts that would suffice for 64 'whole'
combined queues [192 meant for 64 rx, tx and xdp tx queues],
but registers netdev and limits the number of queues based on
information received by qed. In turn, qed doesn't take context
into account when informing qede how many queues it can support.
This would lead to a configuration problem in case user tries
configuring >64 combined queues to interface [or >96 in case
xdp isn't enabled]. Since we don't have a mangement firware
that actually provides so many interrupt lines to a single
device we're currently safe but that's about to change soon.
The new maximum is hence changed:
- For RoCE devices, the limit would remain 64.
- For non-RoCE devices, the limit might be higher [depending
on the actual configuration of the device].
qed would start enforcing that limit in both scenarios.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
|
|
The newly added file causes a harmless warning, with "make W=1":
drivers/net/ethernet/qlogic/qed/qed_iscsi.c: In function 'qed_get_iscsi_ops':
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:1268:29: warning: old-style function definition [-Wold-style-definition]
This makes it a proper prototype.
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
NTB: correct ntb_spad_count comment typo
misc: ibmasm: fix typo in error message
Remove references to dead make variable LINUX_INCLUDE
Remove last traces of ikconfig.h
treewide: Fix printk() message errors
Documentation/device-mapper: s/getsize/getsz/
|
|
This patch fix spelling typos in printk and kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
When calling dma_mapping_error(), the value of return variable rc is 0.
And when the call returns an unexpected value, rc is not set to a
negative errno. Thus, it will return 0 on the error path, and its
callers cannot detect the bug. This patch fixes the bug, assigning
"-ENOMEM" to err.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189041
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds out of order packet handling for hardware offloaded
iSCSI. Out of order packet handling requires driver buffer allocation
and assistance.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the backbone required for the various HW initalizations
which are necessary for the iSCSI driver (qedi) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The chain structure and functions are widely used by the qed* modules,
both for configuration and datapath.
E.g., qede's Tx has one such chain and its Rx has two.
Currently, the strucutre's fields which are required for datapath
related functions [produce/consume] are intertwined with fields which
are required only for configuration purposes [init/destroy/etc.].
This patch re-arranges the chain structure so that all the fields which
are required for datapath usage could reside in a single cacheline instead
of the two which are required today.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
