| Age | Commit message (Collapse) | Author |
|---|
|
Recent additions to the flower app private data have grouped the variables
of a given feature into a struct and added that struct to the main private
data struct.
In keeping with this, move all tunnel related private data to their own
struct. This has no affect on functionality but improves readability and
maintenance of the code.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.
Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-21
The following pull-request contains BPF updates for your *net-next* tree.
There is a merge conflict in test_verifier.c. Result looks as follows:
[...]
},
{
"calls: cross frame pruning",
.insns = {
[...]
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "function calls to other bpf functions are allowed for root only",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
{
"jset: functional",
.insns = {
[...]
{
"jset: unknown const compare not taken",
.insns = {
BPF_RAW_INSN(BPF_JMP | BPF_CALL, 0, 0, 0,
BPF_FUNC_get_prandom_u32),
BPF_JMP_IMM(BPF_JSET, BPF_REG_0, 1, 1),
BPF_LDX_MEM(BPF_B, BPF_REG_8, BPF_REG_9, 0),
BPF_EXIT_INSN(),
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.errstr_unpriv = "!read_ok",
.result_unpriv = REJECT,
.errstr = "!read_ok",
.result = REJECT,
},
[...]
{
"jset: range",
.insns = {
[...]
},
.prog_type = BPF_PROG_TYPE_SOCKET_FILTER,
.result_unpriv = ACCEPT,
.result = ACCEPT,
},
The main changes are:
1) Various BTF related improvements in order to get line info
working. Meaning, verifier will now annotate the corresponding
BPF C code to the error log, from Martin and Yonghong.
2) Implement support for raw BPF tracepoints in modules, from Matt.
3) Add several improvements to verifier state logic, namely speeding
up stacksafe check, optimizations for stack state equivalence
test and safety checks for liveness analysis, from Alexei.
4) Teach verifier to make use of BPF_JSET instruction, add several
test cases to kselftests and remove nfp specific JSET optimization
now that verifier has awareness, from Jakub.
5) Improve BPF verifier's slot_type marking logic in order to
allow more stack slot sharing, from Jiong.
6) Add sk_msg->size member for context access and add set of fixes
and improvements to make sock_map with kTLS usable with openssl
based applications, from John.
7) Several cleanups and documentation updates in bpftool as well as
auto-mount of tracefs for "bpftool prog tracelog" command,
from Quentin.
8) Include sub-program tags from now on in bpf_prog_info in order to
have a reliable way for user space to get all tags of the program
e.g. needed for kallsyms correlation, from Song.
9) Add BTF annotations for cgroup_local_storage BPF maps and
implement bpf fs pretty print support, from Roman.
10) Fix bpftool in order to allow for cross-compilation, from Ivan.
11) Update of bpftool license to GPLv2-only + BSD-2-Clause in order
to be compatible with libbfd and allow for Debian packaging,
from Jakub.
12) Remove an obsolete prog->aux sanitation in dump and get rid of
version check for prog load, from Daniel.
13) Fix a memory leak in libbpf's line info handling, from Prashant.
14) Fix cpumap's frame alignment for build_skb() so that skb_shared_info
does not get unaligned, from Jesper.
15) Fix test_progs kselftest to work with older compilers which are less
smart in optimizing (and thus throwing build error), from Stanislav.
16) Cleanup and simplify AF_XDP socket teardown, from Björn.
17) Fix sk lookup in BPF kselftest's test_sock_addr with regards
to netns_id argument, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The top word of the constant can only have bits set if sign
extension set it to all-1, therefore we don't really have to
mask the top half of the register. We can just OR it into
the result as is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The verifier will now understand the JSET instruction, so don't
mark the dead branch in the JIT as noop. We won't generate any
code, anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Previously the identifier used for indirect block callback registry and
for block rule cb registry (when done via indirect blocks) was the pointer
to the netdev we were interested in receiving updates on. This worked fine
if a single app existed that registered one callback per netdev of
interest. However, if multiple cards are in place and, in turn, multiple
apps, then each app may register the same callback with the same
identifier to both the netdev's indirect block cb list and to a block's cb
list. This can lead to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the app pointer as the identifier for
netdev indirect block cb registry, allowing each app to register a unique
callback per netdev. For block cb registry, the same app may register
multiple cbs to the same block if using TC shared blocks. Instead of the
app, use the pointer to the allocated cb_priv data as the identifier here.
This means that there can be a unique block callback for each app/netdev
combo.
Fixes: 3166dd07a9cb ("nfp: flower: offload tunnel decap rules via indirect TC blocks")
Reported-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation. Add an opt-out flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-12-11
The following pull-request contains BPF updates for your *net-next* tree.
It has three minor merge conflicts, resolutions:
1) tools/testing/selftests/bpf/test_verifier.c
Take first chunk with alignment_prevented_execution.
2) net/core/filter.c
[...]
case bpf_ctx_range_ptr(struct __sk_buff, flow_keys):
case bpf_ctx_range(struct __sk_buff, wire_len):
return false;
[...]
3) include/uapi/linux/bpf.h
Take the second chunk for the two cases each.
The main changes are:
1) Add support for BPF line info via BTF and extend libbpf as well
as bpftool's program dump to annotate output with BPF C code to
facilitate debugging and introspection, from Martin.
2) Add support for BPF_ALU | BPF_ARSH | BPF_{K,X} in interpreter
and all JIT backends, from Jiong.
3) Improve BPF test coverage on archs with no efficient unaligned
access by adding an "any alignment" flag to the BPF program load
to forcefully disable verifier alignment checks, from David.
4) Add a new bpf_prog_test_run_xattr() API to libbpf which allows for
proper use of BPF_PROG_TEST_RUN with data_out, from Lorenz.
5) Extend tc BPF programs to use a new __sk_buff field called wire_len
for more accurate accounting of packets going to wire, from Petar.
6) Improve bpftool to allow dumping the trace pipe from it and add
several improvements in bash completion and map/prog dump,
from Quentin.
7) Optimize arm64 BPF JIT to always emit movn/movk/movk sequence for
kernel addresses and add a dedicated BPF JIT backend allocator,
from Ard.
8) Add a BPF helper function for IR remotes to report mouse movements,
from Sean.
9) Various cleanups in BPF prog dump e.g. to make UAPI bpf_prog_info
member naming consistent with existing conventions, from Yonghong
and Song.
10) Misc cleanups and improvements in allowing to pass interface name
via cmdline for xdp1 BPF example, from Matteo.
11) Fix a potential segfault in BPF sample loader's kprobes handling,
from Daniel T.
12) Fix SPDX license in libbpf's README.rst, from Andrey.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfca5 ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BPF_X support needs indirect shift mode, please see code comments for
details.
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW reconfiguration timeouts are a common indicator of FW trouble.
To make debugging easier print requested update and control word
when reconfiguration fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When troubleshooting incorrect FW capabilities it's useful to know
where the faulty TLV is located. Add offset to all errors messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW/HW can generally support the standard networking offloads
on representors without any trouble. Add the ability for FW
to advertise which features should be available on representors.
Because representors are muxed on top of the vNIC we need to listen
on feature changes of their lower devices, and update their features
appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we never needed to keep a networking locks around
representors accesses, we only accessed them when device was
reconfigured (under nfp pf->lock) or on fast path (under RCU).
Now we want to be able to iterate over all representors during
notifications, so make sure representor assignment is done
under RTNL lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our representors are software devices built on top of the PF
vNIC, the queuing should only happen at the vNIC netdevice.
Allow representors to run qdisc-less.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our representors are software devices built on top of the PF
vNIC, the only state they have are per-cpu stats, so make
the TX run locklessly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for TSO over representors make sure the port id
prepend will always fit in the frame. The current max header
length is 255, which is ample, so assume worst case scenario
of 8 byte prepend and save ourselves the conditionals.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO-related offsets in the descriptor should not include
the length of the prepended metadata. Adjust them. Note that
this could not have caused issues in the past as we don't
support TSO with metadata prepend as of this patch.
Signed-off-by: Michael Rapson <michael.rapson@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nd_q is only used at the very end of nfp_net_tx(), there is no need
to initialize it early.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move temporary variables in scope of the loop in nfp_net_tx_complete(),
and add a temp for txbuf software structure. This saves us 0.2% of CPU.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chained descriptors for fragments need to duplicate all the descriptor
fields of the skb head, so we copy the descriptor and then modify the
relevant fields. This is wasteful, because the top half of the descriptor
will get overwritten entirely while the bottom half is not modified at all.
Copy only the bottom half. This saves us 0.3% of CPU in a GSO test.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.
Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.
Fixes: c01d0efa5136 ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.
Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.
Fixes: 81f3ddf2547d ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-11-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Extend BTF to support function call types and improve the BPF
symbol handling with this info for kallsyms and bpftool program
dump to make debugging easier, from Martin and Yonghong.
2) Optimize LPM lookups by making longest_prefix_match() handle
multiple bytes at a time, from Eric.
3) Adds support for loading and attaching flow dissector BPF progs
from bpftool, from Stanislav.
4) Extend the sk_lookup() helper to be supported from XDP, from Nitin.
5) Enable verifier to support narrow context loads with offset > 0
to adapt to LLVM code generation (currently only offset of 0 was
supported). Add test cases as well, from Andrey.
6) Simplify passing device functions for offloaded BPF progs by
adding callbacks to bpf_prog_offload_ops instead of ndo_bpf.
Also convert nfp and netdevsim to make use of them, from Quentin.
7) Add support for sock_ops based BPF programs to send events to
the perf ring-buffer through perf_event_output helper, from
Sowmini and Daniel.
8) Add read / write support for skb->tstamp from tc BPF and cg BPF
programs to allow for supporting rate-limiting in EDT qdiscs
like fq from BPF side, from Vlad.
9) Extend libbpf API to support map in map types and add test cases
for it as well to BPF kselftests, from Nikita.
10) Account the maximum packet offset accessed by a BPF program in
the verifier and use it for optimizing nfp JIT, from Jiong.
11) Fix error handling regarding kprobe_events in BPF sample loader,
from Daniel T.
12) Add support for queue and stack map type in bpftool, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Original FW only allowed us to perform ECN marking. Newer releases
also support plain old drop. Add the ability to configure drop
policy. This is particularly useful in combination with GRED,
because different bands can have different ECN marking setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use offload of very simple u32 filters to direct packets to GRED
bands based on the DSCP marking. No u32 hashing is supported,
just plain simple filters matching on ToS or Priority with
appropriate mask device can support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Learn how to set the DSCP map. FW uses a packed array which
geometry depends on the number of supported priorities and
virtual queues. Write code to assemble this map and to communicate
the setting to the FW via mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for PRIO offload calculate how long the prio map
for FW will be and make sure the configuration can be performed
via the vNIC mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for GRED offload. It behaves much like RED, but
can apply different parameters to different bands. GRED operates
pretty much exactly like our HW/FW with a single FIFO and different
RED state instances.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wrap RED parameters and stats into a structure, and a 1-element
array. Upcoming GRED offload will add the support for more bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add up stats for all bands for the extra ethtool statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In PRIO-enabled FW read the statistics from per-band symbol, rather
than from the standard per-PCIe-queue counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure the threshold table is large enough to hold information
for all bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for per-band RED offload pass band parameter to
functions. For now it will always be 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for multi-band RED offload if FW is capable map
the extended symbols which will allow us to set per-band parameters
and read stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation of handling more Qdisc types switch to a different
offload strategy. We have now recreated the Qdisc hierarchy in
the driver. Every time the hierarchy changes parse it, and update
the configuration of the HW accordingly.
While at it drop the support of pretending that we can instantiate
a single queue on a multi-queue device in HW/FW. MQ is now required,
and each queue will have its own instance of RED.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new driver Qdisc structure to keep track of parameters
of RED Qdiscs. This way as the Qdisc moves around in the hierarchy
we will be able to configure the HW appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RED qdisc will replace its child Qdisc with a new FIFO queue if
it is reconfigured and the limit parameter is not 0.
This means that when it's created with limit of 0 it will have no FIFO,
and all packets will be dropped. If it's changed and limit is specified
it will loose its existing child (implicit graft). Make sure we mark
RED Qdisc child as NFP_QDISC_UNTRACKED if its not the expected FIFO.
nfp_abm_qdisc_replace() will return 1 if Qdisc already existed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using graft notifications recreate in the driver the full Qdisc
hierarchy. Keep track of how many times each Qdisc is attached
to the hierarchy to make sure we don't offload Qdiscs which are
attached multiple times (device queues can't be shared). For
graft events of Qdiscs we don't know exist make the child as
invalid/untracked.
Note that MQ Qdisc doesn't send destruction events reliably when
device is dismantled, so we need to manually clean out the
children otherwise we'd think Qdiscs which are still in use
are getting freed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To keep track of Qdisc hierarchy allocate a table for children
for each Qdisc. RED Qdisc can only have one child.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep track of which Qdisc is currently root. We need to implement
TC_SETUP_ROOT_QDISC handling, and for completeness also clear the
root Qdisc pointer when it's freed. TC_SETUP_ROOT_QDISC isn't always
sent when device is dismantled.
Remembering the root Qdisc will allow us to build the entire hierarchy
in following patches.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate an object corresponding to any offloaded qdisc we are
informed about by the kernel. Not only the qdiscs we have a
chance of offloading.
The count of created objects will be used to decide whether
the ethtool TC offload can be disabled, since otherwise we may
miss destroy commands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of writing the threshold out when Qdisc is configured
and not remembering it move to a scheme where we remember all
thresholds. When configuration changes parse the offloaded
Qdiscs and set thresholds appropriately.
This will help future extensions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename qdiscs member to red_qdiscs. One of following patches will
use the name qdiscs for tracking all qdisc types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes to NFP mean that stats updates from fw to driver no longer
require a flow lookup and (because egdev offload has been removed) the
ingress netdev for a lookup is now always known.
Remove obsolete code in a flow lookup that matches on host context and
that allows for a netdev to be NULL.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
