| Age | Commit message (Collapse) | Author |
|---|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot switch library does not need this information, but the felix
DSA driver does.
As a reminder, the VSC9959 switch in LS1028A doesn't have an IRQ line
for packet extraction, so to be notified that a PTP packet needs to be
dequeued, it receives that packet also over Ethernet, by setting up a
packet trap. The Felix driver needs to install special kinds of traps
for packets in need of RX timestamps, such that the packets are
replicated both over Ethernet and over the CPU port module.
But the Ocelot switch library sets up more than one trap for PTP event
messages; it also traps PTP general messages, MRP control messages etc.
Those packets don't need PTP timestamps, so there's no reason for the
Felix driver to send them to the CPU port module.
By knowing which traps need PTP timestamps, the Felix driver can
adjust the traps installed using ocelot_trap_add() such that only those
will actually get delivered to the CPU port module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MRP assist code installs a VCAP IS2 trapping rule for each port, but
since the key and the action is the same, just the ingress port mask
differs, there isn't any need to do this. We can save some space in the
TCAM by using a single filter and adjusting the ingress port mask.
Reuse the ocelot_trap_add() and ocelot_trap_del() functions for this
purpose.
Now that the cookies are no longer per port, we need to change the
allocation scheme such that MRP traps use a fixed number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MRP frames are configured to be trapped to the CPU queue 7, and this
number is reflected in the extraction header. However, the information
isn't used anywhere, so just leave MRP frames to go to CPU queue 0
unless needed otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every use case that needed VCAP filters (in order: DSA tag_8021q, MRP,
PTP traps) has hardcoded filter identifiers that worked well enough for
that use case alone. But when two or more of those use cases would be
used together, some of those identifiers would overlap, leading to
breakage.
Add definitions for each cookie and centralize them in ocelot_vcap.h,
such that the overlaps are more obvious.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver uses an identifier equal to (ocelot->num_phys_ports + port)
for MRP traps installed when the system is in the role of an MRC, and an
identifier equal to (port) otherwise.
Use the same identifier in both cases as a consolidation for the various
cookie values spread throughout the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot switchdev driver does not include the CPU port in the list of
flooding destinations for unknown traffic, instead that traffic is
supposed to match FDB entries to reach the CPU.
The addresses it installs are:
(a) the station MAC address, in ocelot_probe_port() and later during
runtime in ocelot_port_set_mac_address(). These are the VLAN-unaware
addresses. The VLAN-aware addresses are in ocelot_vlan_vid_add().
(b) multicast addresses added with dev_mc_add() (not bridge host MDB
entries) in ocelot_mc_sync()
(c) multicast destination MAC addresses for MRP in ocelot_mrp_save_mac(),
to make sure those are dropped (not forwarded) by the bridging
service, just trapped to the CPU
So we can see that the logic is slightly buggy ever since the initial
commit a556c76adc05 ("net: mscc: Add initial Ocelot switch support").
This is because, when ocelot_probe_port() runs, the port pvid is 0.
Then we join a VLAN-aware bridge, the pvid becomes 1, we call
ocelot_port_set_mac_address(), this learns the new MAC address in VID 1
(also fails to forget the old one, since it thinks it's in VID 1, but
that's not so important). Then when we leave the VLAN-aware bridge,
outside world is unable to ping our new MAC address because it isn't
learned in VID 0, the VLAN-unaware pvid.
[ note: this is strictly based on static analysis, I don't have hardware
to test. But there are also many more corner cases ]
The basic idea is that we should have a separation of concerns, and the
FDB entries used for standalone operation should be managed by the
driver, and the FDB entries used by the bridging service should be
managed by the bridge. So the standalone and VLAN-unaware bridge FDB
entries should not follow the bridge PVID, because that will only be
active when the bridge is VLAN-aware. So since the port pvid is
coincidentally zero during probe time, just make those entries
statically go to VID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the driver will always be notified that the role is deleted
before the ring is deleted, then we don't need to duplicate the logic of
cleaning the resources also in the delete function.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a MRP ring was deleted or disabled, the driver was iterating over
the ports to detect if any other MPR rings exists and in case it didn't
exist it would delete the MAC table entry. But the problem was that it
used the last iterated port to delete the MAC table entry and this could
be a NULL port.
The fix consists of using the port on which the function was called.
Fixes: 7c588c3e96e9733a ("net: ocelot: Extend MRP")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.
Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
will not need to do this. So it would be able to have the role MRC
without SW support.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
