| Age | Commit message (Collapse) | Author |
|---|
|
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef987e ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In a future change, the driver will need to determine whether PTP RX
timestamping is enabled on a port (including whether traps were set up
on that port in particular) and that is currently not possible.
The driver supports different RX filters (L2, L4) and kinds of TX
timestamping (one-step, two-step) on its ports, but it saves all
configuration in a single struct hwtstamp_config that is global to the
switch. So, the latest timestamping configuration on one port
(including a request to disable timestamping) affects what gets reported
for all ports, even though the configuration itself is still individual
to each port.
The port timestamping configurations are only coupled because of the
common structure, so replace the hwtstamp_config with a mask of trapped
protocols saved per port. We also have the ptp_cmd to distinguish
between one-step and two-step PTP timestamping, so with those 2 bits of
information we can fully reconstruct a descriptive struct
hwtstamp_config for each port, during the SIOCGHWTSTAMP ioctl.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Fixes: 96ca08c05838 ("net: mscc: ocelot: set up traps for PTP packets")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).
There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During chip initialization, ports that use SGMII / QSGMII to interface to
external phys need to be configured on the VSC7513 and VSC7514. Expose this
configuration routine, so it can be used by DSA drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot-switch driver can utilize the phylink_mac_config routine. Move
this to the ocelot library location and export the symbol to make this
possible.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ocelot chips have an internal PLL that must be used when communicating
through external phys. Expose the init routine, so it can be used by other
drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting the switch core is the same whether it is done internally or
externally. Move this routine to the ocelot library so it can be used by
other drivers.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # regression
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As phylink gained generic support for PHYs with rate matching via PAUSE
frames, the phylink_mac_link_up() method will be called with the maximum
speed and with rx_pause=true if rate matching is in use. This means that
setups with 2500base-x as the SERDES protocol between the MAC/PCS and
the PHY now work with no need for the driver to do anything special.
Tested with fsl-ls1028a-qds-7777.dts.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the following set of commands fails:
$ ip link add br0 type bridge # vlan_filtering 0
$ ip link set swp0 master br0
$ bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged
$ bridge vlan add dev swp0 vid 10
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
Dumping ocelot->vlans, one can see that the 2 egress-untagged VLANs on swp0 are
vid 1 (the bridge PVID) and vid 4094, a PVID used privately by the driver for
VLAN-unaware bridging. So this is why bridge vid 10 is refused, despite
'bridge vlan' showing a single egress untagged VLAN.
As mentioned in the comment added, having this private VLAN does not impose
restrictions to the hardware configuration, yet it is a bookkeeping problem.
There are 2 possible solutions.
One is to make the functions that operate on VLAN-unaware pvids:
- ocelot_add_vlan_unaware_pvid()
- ocelot_del_vlan_unaware_pvid()
- ocelot_port_setup_dsa_8021q_cpu()
- ocelot_port_teardown_dsa_8021q_cpu()
call something different than ocelot_vlan_member_(add|del)(), the latter being
the real problem, because it allocates a struct ocelot_bridge_vlan *vlan which
it adds to ocelot->vlans. We don't really *need* the private VLANs in
ocelot->vlans, it's just that we have the extra convenience of having the
vlan->portmask cached in software (whereas without these structures, we'd have
to create a raw ocelot_vlant_rmw_mask() procedure which reads back the current
port mask from hardware).
The other solution is to filter out the private VLANs from
ocelot_port_num_untagged_vlans(), since they aren't what callers care about.
We only need to do this to the mentioned function and not to
ocelot_port_num_tagged_vlans(), because private VLANs are never egress-tagged.
Nothing else seems to be broken in either solution, but the first one requires
more rework which will conflict with the net-next change 36a0bf443585 ("net:
mscc: ocelot: set up tag_8021q CPU ports independent of user port affinity"),
and I'd like to avoid that. So go with the other one.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220927122042.1100231-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Changing the DSA master means different things depending on the tagging
protocol in use.
For NPI mode ("ocelot" and "seville"), there is a single port which can
be configured as NPI, but DSA only permits changing the CPU port
affinity of user ports one by one. So changing a user port to a
different NPI port globally changes what the NPI port is, and breaks the
user ports still using the old one.
To address this while still permitting the change of the NPI port,
require that the user ports which are still affine to the old NPI port
are down, and cannot be brought up until they are all affine to the same
NPI port.
The tag_8021q mode ("ocelot-8021q") is more flexible, in that each user
port can be freely assigned to one CPU port or to the other. This works
by filtering host addresses towards both tag_8021q CPU ports, and then
restricting the forwarding from a certain user port only to one of the
two tag_8021q CPU ports.
Additionally, the 2 tag_8021q CPU ports can be placed in a LAG. This
works by enabling forwarding via PGID_SRC from a certain user port
towards the logical port ID containing both tag_8021q CPU ports, but
then restricting forwarding per packet, via the LAG hash codes in
PGID_AGGR, to either one or the other.
When we change the DSA master to a LAG device, DSA guarantees us that
the LAG has at least one lower interface as a physical DSA master.
But DSA masters can come and go as lowers of that LAG, and
ds->ops->port_change_master() will not get called, because the DSA
master is still the same (the LAG). So we need to hook into the
ds->ops->port_lag_{join,leave} calls on the CPU ports and update the
logical port ID of the LAG that user ports are assigned to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Drivers could refuse to offload a LAG configuration for a variety of
reasons, mainly having to do with its TX type. Additionally, since DSA
masters may now also be LAG interfaces, and this will translate into a
call to port_lag_join on the CPU ports, there may be extra restrictions
there. Propagate the netlink extack to this DSA method in order for
drivers to give a meaningful error message back to the user.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Decongest ocelot.c a bit more by moving all PTP related logic (including
timestamp processing and PTP packet traps) to ocelot_ptp.c.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ocelot_port_fdb_do_dump() is only used by ocelot_net.c, so move it
there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main C file of the ocelot switch lib, ocelot.c, is getting larger
and larger, and there are plans to add more logic related to stats.
So it seems like an appropriate moment to split the statistics code to a
new file.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Felix PSFP counters suffer from the same problem as the ocelot
ndo_get_stats64 ones - they are 32-bit, so they can easily overflow and
this can easily go undetected.
Add a custom hook in ocelot_check_stats_work() through which driver
specific actions can be taken, and update the stats for the existing
PSFP filters from that hook.
Previously, vsc9959_psfp_filter_add() and vsc9959_psfp_filter_del() were
serialized with respect to each other via rtnl_lock(). However, with the
new entry point into &psfp->sfi_list coming from the periodic worker, we
now need an explicit mutex to serialize access to these lists.
We used to keep a struct felix_stream_filter_counters on stack, through
which vsc9959_psfp_stats_get() - a FLOW_CLS_STATS callback - would
retrieve data from vsc9959_psfp_counters_get(). We need to become
smarter about that in 3 ways:
- we need to keep a persistent set of counters for each stream instead
of keeping them on stack
- we need to promote those counters from u32 to u64, and create a
procedure that properly keeps 64-bit counters. Since we clear the
hardware counters anyway, and we poll every 2 seconds, a simple
increment of a u64 counter with a u32 value will perfectly do the job.
- FLOW_CLS_STATS also expect incremental counters, so we also need to
zeroize our u64 counters every time sch_flower calls us
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support SPI-controlled switches in the future, access to
SYS_STAT_CFG_STAT_VIEW needs to be done outside of any spinlock
protected region, but it still needs to be serialized (by a mutex).
Split the ocelot->stats_lock spinlock into a mutex that serializes
indirect access to hardware registers (ocelot->stat_view_lock) and a
spinlock that serializes access to the u64 ocelot->stats array.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when we have 2 CPU ports configured for DSA tag_8021q mode and
we put them in a LAG, a PGID dump looks like this:
PGID_SRC[0] = ports 4,
PGID_SRC[1] = ports 4,
PGID_SRC[2] = ports 4,
PGID_SRC[3] = ports 4,
PGID_SRC[4] = ports 0, 1, 2, 3, 4, 5,
PGID_SRC[5] = no ports
(ports 0-3 are user ports, ports 4 and 5 are CPU ports)
There are 2 problems with the configuration above:
- user ports should enable forwarding towards both CPU ports, not just 4,
and the aggregation PGIDs should prune one CPU port or the other from
the destination port mask, based on a hash computed from packet headers.
- CPU ports should not be allowed to forward towards themselves and also
not towards other ports in the same LAG as themselves
The first problem requires fixing up the PGID_SRC of user ports, when
ocelot_port_assigned_dsa_8021q_cpu_mask() is called. We need to say that
when a user port is assigned to a tag_8021q CPU port and that port is in
a LAG, it should forward towards all ports in that LAG.
The second problem requires fixing up the PGID_SRC of port 4, to remove
ports 4 and 5 (in a LAG) from the allowed destinations.
After this change, the PGID source masks look as follows:
PGID_SRC[0] = ports 4, 5,
PGID_SRC[1] = ports 4, 5,
PGID_SRC[2] = ports 4, 5,
PGID_SRC[3] = ports 4, 5,
PGID_SRC[4] = ports 0, 1, 2, 3,
PGID_SRC[5] = no ports
Note that PGID_SRC[5] still looks weird (it should say "0, 1, 2, 3" just
like PGID_SRC[4] does), but I've tested forwarding through this CPU port
and it doesn't seem like anything is affected (it appears that PGID_SRC[4]
is being looked up on forwarding from the CPU, since both ports 4 and 5
have logical port ID 4). The reason why it looks weird is because
we've never called ocelot_port_assign_dsa_8021q_cpu() for any user port
towards port 5 (all user ports are assigned to port 4 which is in a LAG
with 5).
Since things aren't broken, I'm willing to leave it like that for now
and just document the oddity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This is a partial revert of commit c295f9831f1d ("net: mscc: ocelot:
switch from {,un}set to {,un}assign for tag_8021q CPU ports"), because
as it turns out, this isn't how tag_8021q CPU ports under a LAG are
supposed to work.
Under that scenario, all user ports are "assigned" to the single
tag_8021q CPU port represented by the logical port corresponding to the
bonding interface. So one CPU port in a LAG would have is_dsa_8021q_cpu
set to true (the one whose physical port ID is equal to the logical port
ID), and the other one to false.
In turn, this makes 2 undesirable things happen:
(1) PGID_CPU contains only the first physical CPU port, rather than both
(2) only the first CPU port will be added to the private VLANs used by
ocelot for VLAN-unaware bridging
To make the driver behave in the same way for both bonded CPU ports, we
need to bring back the old concept of setting up a port as a tag_8021q
CPU port, and this is what deals with VLAN membership and PGID_CPU
updating. But we also need the CPU port "assignment" (the user to CPU
port affinity), and this is what updates the PGID_SRC forwarding rules.
All DSA CPU ports are statically configured for tag_8021q mode when the
tagging protocol is changed to ocelot-8021q. User ports are "assigned"
to one CPU port or the other dynamically (this will be handled by a
future change).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adjusting the PTP clock, the base time of the TAS configuration
will become unreliable. We need reset the TAS configuration by using a
new base time.
For example, if the driver gets a base time 0 of Qbv configuration from
user, and current time is 20000. The driver will set the TAS base time
to be 20000. After the PTP clock adjustment, the current time becomes
10000. If the TAS base time is still 20000, it will be a future time,
and TAS entry list will stop running. Another example, if the current
time becomes to be 10000000 after PTP clock adjust, a large time offset
can cause the hardware to hang.
This patch introduces a tas_clock_adjust() function to reset the TAS
module by using a new base time after the PTP clock adjustment. This can
avoid issues above.
Due to PTP clock adjustment can occur at any time, it may conflict with
the TAS configuration. We introduce a new TAS lock to serialize the
access to the TAS registers.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a desire for the felix driver to gain support for multiple
tag_8021q CPU ports, but the current model prevents it.
This is because ocelot_apply_bridge_fwd_mask() only takes into
consideration whether a port is a tag_8021q CPU port, but not whose CPU
port it is.
We need a model where we can have a direct affinity between an ocelot
port and a tag_8021q CPU port. This serves as the basis for multiple CPU
ports.
Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which
encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to
"ocelot_assign_dsa_8021q_cpu" to express the change of paradigm.
Note that this change makes the first practical use of the new
ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where
we need to remove the old tag_8021q CPU port from the reserved VLAN range.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Absorb the final details of calling ocelot_port_{,un}set_dsa_8021q_cpu(),
i.e. the need to lock &ocelot->fwd_domain_lock, into the callee, to
simplify the caller and permit easier code reuse later.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tag_8021q CPU
Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot
switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that
felix used to have.
This is necessary because the CPU port change procedure will also need
to do this, and it's good to reduce code duplication by having an entry
point in the ocelot switch lib that does all that is needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PGID_CPU must be updated every time a port is configured or unconfigured
as a tag_8021q CPU port. The ocelot switch lib already has a hook for
that operation, so move the updating of PGID_CPU to those hooks.
These bits are pretty specific to DSA, so normally I would keep them out
of the common switch lib, but when tag_8021q is in use, this has
implications upon the forwarding mask determined by
ocelot_apply_bridge_fwd_mask() and called extensively by the switch lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For symmetry with host FDBs and MDBs where the indirection is now
handled outside the ocelot switch lib, do the same for bridge port
flags (unicast/multicast/broadcast flooding).
The only caller of the ocelot switch lib which uses the NPI port is the
Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For symmetry with host FDBs where the indirection is now handled outside
the ocelot switch lib, do the same for host MDB entries. The only caller
of the ocelot switch lib which uses the NPI port is the Felix DSA driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I remembered why we had the host FDB migration procedure in place.
It is true that host FDB entry migration can be done by changing the
value of PGID_CPU, but the problem is that only host FDB entries learned
while operating in NPI mode go to PGID_CPU. When the CPU port operates
in tag_8021q mode, the FDB entries are learned towards the unicast PGID
equal to the physical port number of this CPU port, bypassing the
PGID_CPU indirection.
So host FDB entries learned in tag_8021q mode are not migrated any
longer towards the NPI port.
Fix this by extracting the NPI port -> PGID_CPU redirection from the
ocelot switch lib, moving it to the Felix DSA driver, and applying it
for any CPU port regardless of its kind (NPI or tag_8021q).
Fixes: a51c1c3f3218 ("net: dsa: felix: stop migrating FDBs back and forth on tag proto change")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed commit, VCAP filters can appear on more than one list.
If their action is "trap", they are chained on ocelot->traps via
filter->trap_list. This is in addition to their normal placement on the
VCAP block->rules list head.
Therefore, when we free a VCAP filter, we must remove it from all lists
it is a member of, including ocelot->traps.
There are at least 2 bugs which are direct consequences of this design
decision.
First is the incorrect usage of list_empty(), meant to denote whether
"filter" is chained into ocelot->traps via filter->trap_list.
This does not do the correct thing, because list_empty() checks whether
"head->next == head", but in our case, head->next == head->prev == NULL.
So we dereference NULL pointers and die when we call list_del().
Second is the fact that not all places that should remove the filter
from ocelot->traps do so. One example is ocelot_vcap_block_remove_filter(),
which is where we have the main kfree(filter). By keeping freed filters
in ocelot->traps we end up in a use-after-free in
felix_update_trapping_destinations().
Attempting to fix all the buggy patterns is a whack-a-mole game which
makes the driver unmaintainable. Actually this is what the previous
patch version attempted to do:
https://patchwork.kernel.org/project/netdevbpf/patch/20220503115728.834457-3-vladimir.oltean@nxp.com/
but it introduced another set of bugs, because there are other places in
which create VCAP filters, not just ocelot_vcap_filter_create():
- ocelot_trap_add()
- felix_tag_8021q_vlan_add_rx()
- felix_tag_8021q_vlan_add_tx()
Relying on the convention that all those code paths must call
INIT_LIST_HEAD(&filter->trap_list) is not going to scale.
So let's do what should have been done in the first place and keep a
bool in struct ocelot_vcap_filter which denotes whether we are looking
at a trapping rule or not. Iterating now happens over the main VCAP IS2
block->rules. The advantage is that we no longer risk having stale
references to a freed filter, since it is only present in that list.
Fixes: e42bd4ed09aa ("net: mscc: ocelot: keep traps in a list")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a desire to share the oclot_stats_layout struct outside of the
current vsc7514 driver. In order to do so, the length of the array needs to
be known at compile time, and defined in the struct ocelot and struct
felix_info.
Since the array is defined in a .c file and would be declared in the header
file via:
extern struct ocelot_stat_layout[];
the size of the array will not be known at compile time to outside modules.
To fix this, remove the need for defining the number of stats at compile
time and allow this number to be determined at initialization.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bridge
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c319846086 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the user runs:
bridge link set dev $br_port mcast_flood on
this command should affect not only L2 multicast, but also IPv4 and IPv6
multicast.
In the Ocelot switch, unknown multicast gets flooded according to
different PGIDs according to its type, and PGID_MC only handles L2
multicast. Therefore, by leaving PGID_MCIPV4 and PGID_MCIPV6 at their
default value of 0, unknown IP multicast traffic is never flooded.
Fixes: 421741ea5672 ("net: mscc: ocelot: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220415151950.219660-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Per-flow mirroring with the VCAP IS2 TCAM (in itself handled as an
offload for tc-flower) is done by setting the MIRROR_ENA bit from the
action vector of the filter. The packet is mirrored to the port mask
configured in the ANA:ANA:MIRRORPORTS register (the same port mask as
the destinations for port-based mirroring).
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress protocol ip \
flower skip_sw ip_proto icmp \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ocelot switches perform port-based ingress mirroring if
ANA:PORT:PORT_CFG field SRC_MIRROR_ENA is set, and egress mirroring if
the port is in ANA:ANA:EMIRRORPORTS.
Both ingress-mirrored and egress-mirrored frames are copied to the port
mask from ANA:ANA:MIRRORPORTS.
So the choice of limiting to a single mirror port via ocelot_mirror_get()
and ocelot_mirror_put() may seem bizarre, but the hardware model doesn't
map very well to the user space model. If the user wants to mirror the
ingress of swp1 towards swp2 and the ingress of swp3 towards swp4, we'd
have to program ANA:ANA:MIRRORPORTS with BIT(2) | BIT(4), and that would
make swp1 be mirrored towards swp4 too, and swp3 towards swp2. But there
are no tc-matchall rules to describe those actions.
Now, we could offload a matchall rule with multiple mirred actions, one
per desired mirror port, and force the user to stick to the multi-action
rule format for subsequent matchall filters. But both DSA and ocelot
have the flow_offload_has_one_action() check for the matchall offload,
plus the fact that it will get cumbersome to cross-check matchall
mirrors with flower mirrors (which will be added in the next patch).
As a result, we limit the configuration to a single mirror port, with
the possibility of lifting the restriction in the future.
Frames injected from the CPU don't get egress-mirrored, since they are
sent with the BYPASS bit in the injection frame header, and this
bypasses the analyzer module (effectively also the mirroring logic).
I don't know what to do/say about this.
Functionality was tested with:
tc qdisc add dev swp3 clsact
tc filter add dev swp3 ingress \
matchall skip_sw \
action mirred egress mirror dev swp1
and pinging through swp3, while seeing that the ICMP replies are
mirrored towards swp1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IEEE_8021QAZ_MAX_TCS is defined in include/uapi/linux/dcbnl.h, which is
included by net/dcbnl.h. Then, linux/netdevice.h conditionally includes
net/dcbnl.h if CONFIG_DCB is enabled.
Therefore, when CONFIG_DCB is disabled, this indirect dependency is
broken.
There isn't a good reason to include net/dcbnl.h headers into the ocelot
switch library which exports low-level hardware API, so replace
IEEE_8021QAZ_MAX_TCS with OCELOT_NUM_TC which has the same value.
Fixes: 978777d0fb06 ("net: dsa: felix: configure default-prio and dscp priorities")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220315131215.273450-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for the Felix DSA driver to be able to turn on/off flooding
towards its CPU port, we need to redirect calls on the NPI port to
actually act upon the index in the analyzer block that corresponds to
the CPU port module. This was never necessary until now because DSA
(or the bridge) never called ocelot_port_bridge_flags() for the NPI
port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the logic in the Felix DSA driver and Ocelot switch library.
For Ocelot switches, the DEST_IDX that is the output of the MAC table
lookup is a logical port (equal to physical port, if no LAG is used, or
a dynamically allocated number otherwise). The allocation we have in
place for LAG IDs is different from DSA's, so we can't use that:
- DSA allocates a continuous range of LAG IDs starting from 1
- Ocelot appears to require that physical ports and LAG IDs are in the
same space of [0, num_phys_ports), and additionally, ports that aren't
in a LAG must have physical port id == logical port id
The implication is that an FDB entry towards a LAG might need to be
deleted and reinstalled when the LAG ID changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ocelot switch library does not need this information, but the felix
DSA driver does.
As a reminder, the VSC9959 switch in LS1028A doesn't have an IRQ line
for packet extraction, so to be notified that a PTP packet needs to be
dequeued, it receives that packet also over Ethernet, by setting up a
packet trap. The Felix driver needs to install special kinds of traps
for packets in need of RX timestamps, such that the packets are
replicated both over Ethernet and over the CPU port module.
But the Ocelot switch library sets up more than one trap for PTP event
messages; it also traps PTP general messages, MRP control messages etc.
Those packets don't need PTP timestamps, so there's no reason for the
Felix driver to send them to the CPU port module.
By knowing which traps need PTP timestamps, the Felix driver can
adjust the traps installed using ocelot_trap_add() such that only those
will actually get delivered to the CPU port module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the ocelot-8021q tagging protocol, the CPU port isn't
configured as an NPI port, but is a regular port. So a "trap to CPU"
operation is actually a "redirect" operation. So DSA needs to set up the
trapping action one way or another, depending on the tagging protocol in
use.
To ease DSA's work of modifying the action, keep all currently installed
traps in a list, so that DSA can live-patch them when the tagging
protocol changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MRP assist code installs a VCAP IS2 trapping rule for each port, but
since the key and the action is the same, just the ingress port mask
differs, there isn't any need to do this. We can save some space in the
TCAM by using a single filter and adjusting the ingress port mask.
Reuse the ocelot_trap_add() and ocelot_trap_del() functions for this
purpose.
Now that the cookies are no longer per port, we need to change the
allocation scheme such that MRP traps use a fixed number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
