| Age | Commit message (Collapse) | Author |
|---|
|
When the action of an xdp program was XDP_TX, lan966x was creating
a xdp_frame and use this one to send the frame back. But it is also
possible to send back the frame without needing a xdp_frame, because
it is possible to send it back using the page.
And then once the frame is transmitted is possible to use directly
page_pool_recycle_direct as lan966x is using page pools.
This would save some CPU usage on this path, which results in higher
number of transmitted frames. Bellow are the statistics:
Frame size: Improvement:
64 ~8%
256 ~11%
512 ~8%
1000 ~0%
1500 ~0%
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20230422142344.3630602-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever a frame was received to the CPU, the HW is timestamping the
frame. In the IFH(Inter Frame Header) it is found the nanosecond part
of the timestamps the SW is required to read from HW the second part.
But reading the second part it seems to be a expensive operations, so
so change this such to read the second part only when rx filter is
enabled.
Doing this change gives the RX a performance boost of ~70mbit.
before:
[ 5] 0.00-10.01 sec 546 MBytes 457 Mbits/sec 0 sender
now:
[ 5] 0.00-10.01 sec 652 MBytes 530 Mbits/sec 0 sender
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: a825b611c7c1 ("net: lan966x: Add support for XDP_REDIRECT")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend lan966x XDP support with the action XDP_REDIRECT. This is similar
with the XDP_TX, so a lot of functionality can be reused.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend lan966x XDP support with the action XDP_TX. In this case when the
received buffer needs to execute XDP_TX, the buffer will be moved to the
TX buffers. So a new RX buffer will be allocated.
When the TX finish with the frame, it would give back the buffer to the
page pool.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To add support for XDP_TX it is required to be able to write to the DMA
area therefore it is required that the pages will be mapped using
DMA_BIDIRECTIONAL flag.
Therefore check if there are any xdp programs on the interfaces and in
that case set DMA_BIDRECTIONAL otherwise use DMA_FROM_DEVICE.
Therefore when a new XDP program is added it is required to redo the
page_pool.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default the rxq memory model is MEM_TYPE_PAGE_SHARED but to be able
to reuse pages on the TX side, when the XDP action XDP_TX it is required
to update the memory model to PAGE_POOL.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when a frame was transmitted, it is required to unamp the
frame that was transmitted. The length of the frame was taken from the
transmitted skb. In the future we might not have an skb, therefore store
the length skb directly in the lan966x_tx_dcb_buf and use this one to
unamp the frame.
While at this, also arrange the members in lan966x_tx_dcb_buf not to
have any holes.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce lan966x_fdma_tx_setup_dcb and lan966x_fdma_tx_start functions
and use of them inside lan966x_fdma_xmit. There is no functional change
in here.
They are introduced to be used when XDP_TX/REDIRECT actions are
introduced.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the page_pool params to allocate XDP_PACKET_HEADROOM space as
headroom for all received frames.
This is needed for when the XDP_TX and XDP_REDIRECT are implemented.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the page_pool API for allocation, freeing and DMA handling instead
of dev_alloc_pages, __free_pages and dma_map_page.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce basic XDP support to lan966x driver. Currently the driver
supports only the actions XDP_PASS, XDP_DROP and XDP_ABORTED.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function lan966x_fdma_rx_get_frame was unmapping the frame from
device and check also if the frame was received on a valid port. And
only after that it tried to generate the skb.
Move this check in a different function, in preparation for xdp
support. Such that xdp to be added here and the
lan966x_fdma_rx_get_frame to be used only when giving the skb to upper
layers.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The total length of IFH(inter frame header) in bytes is calculated as
IFH_LEN * sizeof(u32). Because IFH_LEN describes the length in words
and not in bytes. As the length of IFH in bytes is used quite often,
add a define for this. This is just to simplify the things.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When lan966x was receiving a frame, then it was building the skb and
after that it was calling dma_unmap_single with frame size as the
length. This actually has 2 issues:
1. It is using a length to map and a different length to unmap.
2. When the unmap was happening, the data was sync for cpu but it could
be that this will overwrite what build_skb was initializing.
The fix for these two problems is to change the order of operations.
First to sync the frame for cpu, then to build the skb and in the end to
unmap using the correct size but without sync the frame again for cpu.
Fixes: c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221031133421.1283196-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When MTU is changed, FDMA is required to calculate what is the maximum
size of the frame that it can received. So it can calculate what is the
page order needed to allocate for the received frames.
The first problem was that, when the max MTU was calculated it was
reading the value from dev and not from HW, so in this way it was
missing L2 header + the FCS.
The other problem was that once the skb is created using
__build_skb_around, it would reserve some space for skb_shared_info.
So if we received a frame which size is at the limit of the page order
then the creating will failed because it would not have space to put all
the data.
Fixes: 2ea1cbac267e ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a frame is sent using FDMA, the skb is mapped and then the mapped
address is given to an tx dcb that is different than the last used tx
dcb. Once the HW finish with this frame, it would generate an interrupt
and then the dcb can be reused and memory can be freed. For each dcb
there is an dcb buf that contains some meta-data(is used by PTP, is
it free). There is 1 to 1 relationship between dcb and dcb_buf.
The following issue was observed. That sometimes after changing the MTU
to allocate new tx dcbs and dcbs_buf, two frames were not
transmitted. The frames were not transmitted because when reloading the
tx dcbs, it was always presuming to use the first dcb but that was not
always happening. Because it could be that the last tx dcb used before
changing MTU was first dcb and then when it tried to get the next dcb it
would take dcb 1 instead of 0. Because it is supposed to take a
different dcb than the last used one. This can be fixed simply by
changing tx->last_in_use to -1 when the fdma is disabled to reload the
new dcb and dcbs_buff.
But there could be a different issue. For example, right after the frame
is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be
cleared. And now get the interrupt from HW that it finished with the
frame. So when we try to clear the skb, it is not possible because we
lost all the dcbs_buf.
The solution here is to stop replacing the tx dcbs and dcbs_buf when
changing MTU because the TX doesn't care what is the MTU size, it is
only the RX that needs this information.
Fixes: 2ea1cbac267e ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221021090711.3749009-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Don't just print a warning. Clean up and return an error as well.
Fixes: c8349639324a ("net: lan966x: Add FDMA functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/YwjgDm/SVd5c1tQU@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The smatch found the following warning:
drivers/net/ethernet/microchip/lan966x/lan966x_fdma.c:736 lan966x_fdma_reload()
warn: 'rx_dcbs' was already freed.
This issue can happen when changing the MTU on one of the ports and once
the RX buffers are allocated and then the TX buffer allocation fails.
In that case the RX buffers should not be restore. This fix this issue
such that the RX buffers will not be restored if the TX buffers failed
to be allocated.
Fixes: 2ea1cbac267e2a ("net: lan966x: Update FDMA to change MTU.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220511204059.2689199-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When changing the MTU, it is required to change also the size of the
DBs. In case those frames will arrive to CPU.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethernet frames can be extracted or injected to or from the device's
DDR memory. There is one channel for injection and one channel for
extraction. Each of these channels contain a linked list of DCBs which
contains DB. The DCB contains only 1 DB for both the injection and
extraction. Each DB contains a frame. Every time when a frame is received
or transmitted an interrupt is generated.
It is not possible to use both the FDMA and the manual
injection/extraction of the frames. Therefore the FDMA has priority over
the manual because of better performance values.
FDMA:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 420 MBytes 352 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 420 MBytes 351 Mbits/sec receiver
iperf -c 192.168.1.1 -R
[ 5] 0.00-10.01 sec 528 MBytes 442 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 524 MBytes 440 Mbits/sec receiver
Manual:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 93.8 MBytes 78.5 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 93.8 MBytes 78.4 Mbits/sec receiver
ipers -c 192.168.1.1 -R
[ 5] 0.00-10.03 sec 121 MBytes 101 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 118 MBytes 99.0 Mbits/sec receiver
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
