| Age | Commit message (Collapse) | Author |
|---|
|
the dtsi
Because hw lro started to be supported from MT7623, the proper way to check if
the feature is capable is to judge by the chip id instead of by the dtsi.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver gets the chip id by ETHSYS_CHIPID0_3/ETHSYS_CHIPID4_7 registers
in mtk_probe().
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(1) Modify the register settings for LRO relinquishments
(2) Jump out from the waiting loop while LRO relinquishments are done
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reuse phydev already in struct net_device instead of creating
another new one in private structure.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
through TRGMII
Changing dynamically source clock, TX/RX delay and interface mode
used by TRGMII hardware module inside PHY capability polling routine
for adapting to the various speed of RGMII used by external PHY for
GMAC0.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
adds PHY-mode "trgmii" as an extension for the operation
mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII.
and adds a variable trgmii inside mtk_mac as the indication
to make the difference between the MAC connected to internal
switch or connected to external PHY by the given configuration
on the board and then to perform the corresponding setup on
TRGMII hardware module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The codes add the large receive offload (LRO) functions by hardware as below:
1) PDMA has total four RX rings that one is the normal ring, and others can
be configured as LRO rings.
2) Only TCP/IP RX flows can be offloaded. The hardware can set four IP
addresses at most, if the destination IP of the RX flow matches one of
them, it has the chance to be offloaded.
3) There three RX flows can be offloaded at most, and one flow is mapped to
one RX ring.
4) If there are more than three candidate RX flows, the hardware can
choose three of them by throughput comparison results.
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add the protection of the race condition between
the reset process and hardware access happening
on the related callbacks.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct mtk_eth has already contained struct regmap ethsys pointer
to the address range of the internal circuit reset, so we reuse it
to reset more internal blocks on ethernet hardware such as packet
processing engine (PPE) and frame engine (FE) instead of rstc which
deals with FE only.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) original driver only resets DMA used by descriptor rings
which can't guarantee it can recover all various kinds of fatal
errors, so the patch tries to reset the underlying hardware
resource from scratch on Mediatek SoC required for ethernet
running, including power, pin mux control, clock and internal
circuits on the ethernet in order to restore into the initial
state which the rebooted machine gives.
2) add state variable inside structure mtk_eth to help distinguish
mtk_hw_init is called between the initialization during boot time
or re-initialization during the reset process.
3) add ge_mode variable inside structure mtk_mac for restoring
the interface mode of the current setup for the target MAC.
4) remove __init attribute from mtk_hw_init definition
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
EPROBE_DEFER
1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethernet RX
Because the PDMA has richer features than the QDMA for Ethernet RX
(such as multiple RX rings, HW LRO, etc.),
the patch modifies to use the PDMA to handle Ethernet RX.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethernet core has 3 IRQs. Using the IRQ grouping registers we are able
to separate TX and RX IRQs, which allows us to service them on separate
cores. This patch splits the IRQ handler into 2 separate functions, one for
TX and another for RX. The TX housekeeping is split out into its own NAPI
handler.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code that enables and disables IRQs is missing proper locking. After
adding the IRQ grouping patch and routing the RX and TX IRQs to different
cores we experienced IRQ stalls. Fix this by adding proper locking.
We use a dedicated lock to reduce the latency if the IRQ code.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QDMA engine can fail to update the register pointing to the next TX
descriptor if this bit does not get set in the QDMA configuration register.
Not setting this bit can result in invalid values inside the TX rings
registers which will causes TX stalls.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Scratch memory gets allocated in mtk_init_fq_dma() but the corresponding
code to free it is missing inside mtk_dma_free() causing a memory leak.
With this patch applied, we can run ifconfig up/down several thousand
times without any problems.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The worker always touches both netdevs. It is ethernet core and not MAC
specific. We only need one worker, which belongs into the ethernets core
struct.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethernet support for MediaTek SoCs from the MT7623 family. These have
dual GMAC. Depending on the exact version, there might be a built-in
Gigabit switch (MT7530). The core does not have the typical DMA ring setup.
Instead there is a linked list that we add descriptors to. There is only
one linked list that both MACs use together. There is a special field
inside the TX descriptors called the VQID. This allows us to assign packets
to different internal queues. By using a separate id for each MAC we are
able to get deterministic results for BQL. Additionally we need to
provide the core with a block of scratch memory that is the same size as
the RX ring and data buffer. This is really needed to make the HW datapath
work. Although the driver does not support this yet, we still need to
assign the memory and tell the core about it for RX to work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
