| Age | Commit message (Collapse) | Author |
|---|
|
Implements tc offload support for rvu representors.
Usage example:
- Add tc rule to drop packets with vlan id 3 using port
representor(Rpf1vf0).
# tc filter add dev Rpf1vf0 protocol 802.1Q parent ffff: flower
vlan_id 3 vlan_ethtype ipv4 skip_sw action drop
- Redirect packets with vlan id 5 and IPv4 packets to eth1,
after stripping vlan header.
# tc filter add dev Rpf1vf0 ingress protocol 802.1Q flower vlan_id 5
vlan_ethtype ipv4 skip_sw action vlan pop action mirred ingress
redirect dev eth1
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register devlink port for the rvu representors.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware supports different types of MACs eg RPM, SDP, LBK.
LBK is for internal Tx->Rx HW loopback path. RPM and SDP MACs support
ingress/egress pkt IO on interfaces with different set of capabilities
like interface modes. At the time of netdev driver registration PF will
seek MAC related information from Admin function driver
'drivers/net/ethernet/marvell/octeontx2/af' and sets up ingress/egress
queues etc such that pkt IO on the channels of these different MACs is
possible. This patch add representors for SDP MAC.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implements the below requirement mentioned
in the representors documentation.
"
The representee's link state is controlled through the
representor. Setting the representor administratively UP
or DOWN should cause carrier ON or OFF at the representee.
"
This patch enables
- Reflecting the link state of representor based on the VF state and
link state of VF based on representor.
- On VF interface up/down a notification is sent via mbox to representor
to update the link state.
eg: ip link set eth0 up/down will disable carrier on/off
of the corresponding representor(r0p1) interface.
- On representor interface up/down will cause the link state update of VF.
eg: ip link set r0p1 up/down will disable carrier on/off
of the corresponding representee(eth0) interface.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support to export VF port statistics via representor
netdev. Defines new mbox "NIX_LF_STATS" to fetch VF hw stats.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current HW, do not support in-built switch which will forward pkts
between representee and representor. When representor is put under
a bridge and pkts needs to be sent to representee, then pkts from
representor are sent on a HW internal loopback channel, which again
will be punted to ingress pkt parser. Now the rules that this patch
installs are the MCAM filters/rules which will match against these
pkts and forward them to representee.
The rules that this patch installs are for basic
representor <=> representee path similar to Tun/TAP between VM and
Host.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds basic driver for the RVU representor.
Driver on probe does pci specific initialization and
does hw resources configuration. Introduces RVU_ESWITCH
kernel config to enable/disable the driver. Representor
and NIC shares the code but representors netdev support
subset of NIC functionality. Hence "otx2_rep_dev" API
helps to skip the features initialization that are not
supported by the representors.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink knobs to enable/disable counters on NPC
default rule entries.
Sample command to enable default rule counters:
devlink dev param set <dev> name npc_def_rule_cntr value true cmode runtime
Sample command to read the counter:
cat /sys/kernel/debug/cn10k/npc/mcam_rules
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Link: https://patch.msgid.link/20241105125620.2114301-3-lcherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce lowlevel variant of rvu_mcam_remove/add_counter_from/to_rule
for better code reuse, which assumes necessary locks are taken at
higher level.
These low level functions would be used for implementing default rule
counter APIs in the subsequent patch.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241105125620.2114301-2-lcherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc4).
Conflicts:
107a034d5c1e ("net/mlx5: qos: Store rate groups in a qos domain")
1da9cfd6c41c ("net/mlx5: Unregister notifier on eswitch init failure")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The left shift int 32 bit integer constants 1 is evaluated using 32 bit
arithmetic and then assigned to a 64 bit unsigned integer. In the case
where the shift is 32 or more this can lead to an overflow. Avoid this
by shifting using the BIT_ULL macro instead.
Fixes: 019aba04f08c ("octeontx2-af: Modify SMQ flush sequence to drop packets")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/20241010154519.768785-1-colin.i.king@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert struct rvu_block block to const struct rvu_block *block in
get_lf_str_list() function parameter. This improves efficiency by
avoiding structure copying and reflects the function's read-only
access to block.
Signed-off-by: Riyan Dhiman <riyandhiman14@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241001110542.5404-2-riyandhiman14@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Display channel info in the RPM map debugfs output.
With this, cat /sys/kernel/debug/cn10k/rvu_pf_rpm_map
would display channel number for each device in addition to
the existing data.
Sample output:
PCI dev RVU PF Func NIX block rpm LMAC CHAN
0002:02:00.0 0x400 NIX0 rpm0 LMAC0 256
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Link: https://patch.msgid.link/20240912161450.164402-3-lcherian@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb227 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb04 ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current implementation of SMQ flush sequence waits for the packets
in the TM pipeline to be transmitted out of the link. This sequence
doesn't succeed in HW when there is any issue with link such as lack of
link credits, link down or any other traffic that is fully occupying the
link bandwidth (QoS). This patch modifies the SMQ flush sequence to
drop the packets after TL1 level (SQM) instead of polling for the packets
to be sent out of RPM/CGX link.
Fixes: 5d9b976d4480 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://patch.msgid.link/20240906045838.1620308-1-naveenm@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Recently I noticed that both gcc-14 and clang-18 report that passing
a non-string literal as the format argument of alloc_workqueue()
is potentially insecure.
E.g. clang-18 says:
.../rvu.c:2493:32: warning: format string is not a string literal (potentially insecure) [-Wformat-security]
2493 | mw->mbox_wq = alloc_workqueue(name,
| ^~~~
.../rvu.c:2493:32: note: treat the string as an argument to avoid this
2493 | mw->mbox_wq = alloc_workqueue(name,
| ^
| "%s",
It is always the case where the contents of name is safe to pass as the
format argument. That is, in my understanding, it never contains any
format escape sequences.
But, it seems better to be safe than sorry. And, as a bonus, compiler
output becomes less verbose by addressing this issue as suggested by
clang-18.
Compile tested only by author.
Tested-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240904-octeontx2-sparse-v2-1-14f2305fe4b2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The maximum CPT credits that RXC can use are now configurable on CN10KA B0
through a hardware CSR. This patch sets the default value to optimize peak
performance, aligning it with other chip versions.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch modifies the driver to prevent access to RXC hardware
registers on the CN10KB, as RXC is not available on this chip.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the driver to use a dynamic number of vectors instead
of a hard-coded value. This change accommodates the CN10KB, which has 2
vectors, unlike the previously supported chips that have 3 vectors.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some CPT AF registers are per LF and others are global. Translation
of PF/VF local LF slot number to actual LF slot number is required
only for accessing perf LF registers. CPT AF global registers access
do not require any LF slot number. Also, there is no reason CPT
PF/VF to know actual lf's register offset.
Without this fix microcode loading will fail, VFs cannot be created
and hardware is not usable.
Fixes: bc35e28af789 ("octeontx2-af: replace cpt slot with lf id on reg write")
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240821070558.1020101-1-bbhushan2@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
f7ce5eb2cb79 ("bnxt_en: Fix crash in bnxt_get_max_rss_ctx_ring()")
20c8ad72eb7f ("eth: bnxt: use the RSS context XArray instead of the local list")
Adjacent changes:
net/ethtool/ioctl.c
503757c80928 ("net: ethtool: Fix RSS setting")
eac9122f0c41 ("net: ethtool: record custom RSS contexts in the XArray")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While performing RSS based on IPv4, packets with
IPv4 options are not being considered. Adding changes
to match both plain IPv4 and IPv4 with option header.
Fixes: 41a7aa7b800d ("octeontx2-af: NIX Rx flowkey configuration for RSS")
Signed-off-by: Satheesh Paul <psatheesh@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While performing RSS based on IPv6, extension ltype
is not being considered. This will be problem for
fragmented packets or packets with extension header.
Adding changes to match IPv6 ext header along with IPv6
ltype.
Fixes: 41a7aa7b800d ("octeontx2-af: NIX Rx flowkey configuration for RSS")
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checksum and length checks are not enabled for IPv4 header with
options and IPv6 with extension headers.
To fix this a change in enum npc_kpu_lc_ltype is required which will
allow adjustment of LTYPE_MASK to detect all types of IP headers.
Fixes: 21e6699e5cd6 ("octeontx2-af: Add NPC KPU profile")
Signed-off-by: Michal Mazur <mmazur2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes CPT_LF_ALLOC mailbox error due to
incompatible mailbox message format. Specifically, it
corrects the `blkaddr` field type from `int` to `u8`.
Fixes: de2854c87c64 ("octeontx2-af: Mailbox changes for 98xx CPT block")
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace slot id with global CPT lf id on reg read/write as
CPTPF/VF driver would send slot number instead of global
lf id in the reg offset. And also update the mailbox response
with the global lf's register offset.
Fixes: ae454086e3c2 ("octeontx2-af: add mailbox interface for CPT")
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/act_ct.c
26488172b029 ("net/sched: Fix UAF when resolving a clash")
3abbd7ed8b76 ("act_ct: prepare for stolen verdict coming from conntrack and nat engine")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rvu_check_rsrc_availability()
In rvu_check_rsrc_availability() in case of invalid SSOW req, an incorrect
data is printed to error log. 'req->sso' value is printed instead of
'req->ssow'. Looks like "copy-paste" mistake.
Fix this mistake by replacing 'req->sso' with 'req->ssow'.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 746ea74241fa ("octeontx2-af: Add RVU block LF provisioning support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240705095317.12640-1-amishin@t-argos.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Octeontx2 hardware uses Near Data Cache(NDC) block to cache
contexts in it so that access to LLC/DRAM can be avoided.
It is recommended in HRM to sync the NDC contents before
releasing/resetting LF resources. Hence implement NDC_SYNC
mailbox and sync contexts during driver teardown.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/pensando/ionic/ionic_txrx.c
d9c04209990b ("ionic: Mark error paths in the data path as unlikely")
491aee894a08 ("ionic: fix kernel panic in XDP_TX action")
net/ipv6/ip6_fib.c
b4cb4a1391dc ("net: use unrcu_pointer() helper")
b01e1c030770 ("ipv6: fix possible race in __fib6_drop_pcpu_from()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds support to dump NIX transmit queue topology.
There are multiple levels of scheduling/shaping supported by
NIX and a packet traverses through multiple levels before sending
the packet out. At each level, there are set of scheduling/shaping
rules applied to a packet flow.
Each packet traverses through multiple levels
SQ->SMQ->TL4->TL3->TL2->TL1 and these levels are mapped in a parent-child
relationship.
This patch dumps the debug information related to all TM Levels in
the following way.
Example:
$ echo <nixlf> > /sys/kernel/debug/octeontx2/nix/tm_tree
$ cat /sys/kernel/debug/octeontx2/nix/tm_tree
A more desriptive set of registers at each level can be dumped
in the following way.
Example:
$ echo <nixlf> > /sys/kernel/debug/octeontx2/nix/tm_topo
$ cat /sys/kernel/debug/octeontx2/nix/tm_topo
Signed-off-by: Anshumali Gaur <agaur@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF mcam entries has to be at low priority always so that VF
can install longest prefix match rules at higher priority.
This was taken care currently but when priority allocation
wrt reference entry is requested then entries are allocated
from mid-zone instead of low priority zone. Fix this and
always allocate entries from low priority zone for PFs.
Fixes: 7df5b4b260dd ("octeontx2-af: Allocate low priority entries for PF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/filter.h
kernel/bpf/core.c
66e13b615a0c ("bpf: verifier: prevent userspace memory access")
d503a04f8bc0 ("bpf: Add support for certain atomics in bpf_arena to x86 JIT")
https://lore.kernel.org/all/20240429114939.210328b0@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d136 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/ti/icssg/icssg_prueth.c
net/mac80211/chan.c
89884459a0b9 ("wifi: mac80211: fix idle calculation with multi-link")
87f5500285fb ("wifi: mac80211: simplify ieee80211_assign_link_chanctx()")
https://lore.kernel.org/all/20240422105623.7b1fbda2@canb.auug.org.au/
net/unix/garbage.c
1971d13ffa84 ("af_unix: Suppress false-positive lockdep splat for spin_lock() in __unix_gc().")
4090fa373f0e ("af_unix: Replace garbage collection algorithm.")
drivers/net/ethernet/ti/icssg/icssg_prueth.c
drivers/net/ethernet/ti/icssg/icssg_common.c
4dcd0e83ea1d ("net: ti: icssg-prueth: Fix signedness bug in prueth_init_rx_chns()")
e2dc7bfd677f ("net: ti: icssg-prueth: Move common functions into a separate file")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang static checker(scan-build) warning：
drivers/net/ethernet/marvell/octeontx2/af/rvu_npc.c:line 2184, column 2
Attempt to free released memory.
npc_mcam_rsrcs_deinit() has released 'mcam->counters.bmap'. Deleted this
redundant kfree() to fix this double free problem.
Fixes: dd7842878633 ("octeontx2-af: Add new devlink param to configure maximum usable NIX block LFs")
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240424022724.144587-1-suhui@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend devlink_param *set function pointer to take extack as a param.
Sometimes it is needed to pass information to the end user from set
function. It is more proper to use for that netlink instead of passing
message to dmesg.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Support offloading of skbedit mark action.
For example, to mark with 0x0008, with dest ip 60.60.60.2 on eth2
interface:
# tc qdisc add dev eth2 ingress
# tc filter add dev eth2 ingress protocol ip flower \
dst_ip 60.60.60.2 action skbedit mark 0x0008 skip_sw
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/unix/garbage.c
47d8ac011fe1 ("af_unix: Fix garbage collector racing against connect()")
4090fa373f0e ("af_unix: Replace garbage collection algorithm.")
Adjacent changes:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
faa12ca24558 ("bnxt_en: Reset PTP tx_avail after possible firmware reset")
b3d0083caf9a ("bnxt_en: Support RSS contexts in ethtool .{get|set}_rxfh()")
drivers/net/ethernet/broadcom/bnxt/bnxt_ulp.c
7ac10c7d728d ("bnxt_en: Fix possible memory leak in bnxt_rdma_aux_device_init()")
194fad5b2781 ("bnxt_en: Refactor bnxt_rdma_aux_device_init/uninit functions")
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
958f56e48385 ("net/mlx5e: Un-expose functions in en.h")
49e6c9387051 ("net/mlx5e: RSS, Block XOR hash with over 128 channels")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
NIX SQ mode and link backpressure configuration is required for
all platforms. But in current driver this code is wrongly placed
under specific platform check. This patch fixes the issue by
moving the code out of platform check.
Fixes: 5d9b976d4480 ("octeontx2-af: Support fixed transmit scheduler topology")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240408063643.26288-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/ip_gre.c
17af420545a7 ("erspan: make sure erspan_base_hdr is present in skb->head")
5832c4a77d69 ("ip_tunnel: convert __be16 tunnel flags to bitmaps")
https://lore.kernel.org/all/20240402103253.3b54a1cf@canb.auug.org.au/
Adjacent changes:
net/ipv6/ip6_fib.c
d21d40605bca ("ipv6: Fix infinite recursion in fib6_dump_done().")
5fc68320c1fb ("ipv6: remove RTNL protection from inet6_dump_fib()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reset CGX/RPM MAC HW statistics at the time of driver probe()
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rvu_map_cgx_lmac_pf() the 'iter', which is used as an array index, can reach
value (up to 14) that exceed the size (MAX_LMAC_COUNT = 8) of the array.
Fix this bug by adding 'iter' value check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 91c6945ea1f9 ("octeontx2-af: cn10k: Add RPM MAC support")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Any NIX interface type can have maximum 256 channels. So increased the
backpressure ID count to 256 so that it can cover cn9k and cn10k SoCs that
have different NIX interface types with varied maximum channels.
Signed-off-by: Radha Mohan Chintakuntla <radhac@marvell.com>
Link: https://lore.kernel.org/r/20240326184514.1628284-1-radhac@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current implementation for loading coalesced KPU profiles has
a limitation. The "offset" field, which is used to locate profiles
within the profile is restricted to a u16.
This restricts the number of profiles that can be loaded. This patch
addresses this limitation by increasing the size of the "offset" field.
Fixes: 11c730bfbf5b ("octeontx2-af: support for coalescing KPU profiles")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Octeontx2 MAC block (CGX) has separate data paths (SMU and GMP) for
different speeds, allowing for efficient data transfer.
The previous patch which added pause frame configuration has a bug due
to which pause frame feature is not working in GMP mode.
This patch fixes the issue by configurating appropriate registers.
Fixes: f7e086e754fe ("octeontx2-af: Pause frame configuration at cgx")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326052720.4441-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f58d ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
