| Age | Commit message (Collapse) | Author |
|---|
|
By design, the idleslope increments are restricted to 16.384kbps steps.
Add a comment to igb_main.c making that explicit and add one example
that illustrates the impact of that.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to section 12.0.3.4.13 "Receive Descriptor Control - RXDCTL"
of the Intel® 82579 Gigabit Ethernet PHY Datasheet v2.1:
"HTHRESH should be given a non zero value when ever PTHRESH is
used."
In RXDCTL(0), PTHRESH lives at bits 5:0, and HTHREST lives at bits 13:8.
Set only bit 8 of HTHREST as is done in e1000_flush_rx_ring(). Found by
inspection.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a new function igb_get_max_rss_queues() to get maximum
RSS queues, this will reduce duplicate code and facilitate future
maintenance.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Before libvirt modifies the MAC address and vlan tag for an SRIOV VF
for use by a virtual machine (either using vfio device assignment or
macvtap passthru mode), it saves the current MAC address and vlan tag
so that it can reset them to their original value when the guest is
done. Libvirt can't leave the VF MAC set to the value used by the
now-defunct guest since it may be started again later using a
different VF, but it certainly shouldn't just pick any random value,
either. So it saves the state of everything prior to using the VF, and
resets it to that.
The igb driver initializes the MAC addresses of all VFs to
00:00:00:00:00:00, and reports that when asked (via an RTM_GETLINK
netlink message, also visible in the list of VFs in the output of "ip
link show"). But when libvirt attempts to restore the MAC address back
to 00:00:00:00:00:00 (using an RTM_SETLINK netlink message) the kernel
responds with "Invalid argument".
Forbidding a reset back to the original value leaves the VF MAC at the
value set for the now-defunct virtual machine. Especially on a system
with NetworkManager enabled, this has very bad consequences, since
NetworkManager forces all interfacess to be IFF_UP all the time - if
the same virtual machine is restarted using a different VF (or even on
a different host), there will be multiple interfaces watching for
traffic with the same MAC address.
To allow libvirt to revert to the original state, we need a way to
remove the administrative set MAC on a VF, to allow normal host
operation again, and to reset/overwrite the VF MAC via VF netdev.
This patch implements the outlined scenario by allowing to set the
VF MAC to 00:00:00:00:00:00 via RTM_SETLINK on the PF.
igb_ndo_set_vf_mac resets the IGB_VF_FLAG_PF_SET_MAC flag to 0,
so it's possible to reset the VF MAC back to the original value via
the VF netdev.
Note: Recent patches to libvirt allow for a workaround if the NIC
isn't capable of resetting the administrative MAC back to all 0, but
in theory the NIC should allow resetting the MAC in the first place.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-01-23
This series contains updates to i40e and i40evf only.
Pawel enables FlatNVM support on x722 devices by allowing nvmupdate tool
to configure the preservation flags in the AdminQ command.
Mitch fixes a potential divide by zero error when DCB is enabled and
the firmware fails to configure the VSI, so check for this state.
Fixed a bug where the driver could fail to adhere to ETS bandwidth
allocations if 8 traffic classes were configured on the switch.
Sudheer fixes a potential deadlock by avoiding to call
flush_schedule_work() in i40evf_remove(), since cancel_work_sync()
and cancel_delayed_work_sync() already cleans up necessary work items.
Fixed an issue with the problematic detection and recovery from
hung queues in the PF which was causing lost interrupts. This is done
by triggering a software interrupt so that interrupts are forced on
and if we are already in napi_poll and an interrupt fires, napi_poll
will not be rescheduled and the interrupt is lost.
Avinash fixes an issue in the VF where is was possible to issue a
reset_task while the device is currently being removed.
Michal fixes an issue occurring while calling i40e_led_set() with
the blink parameter set to true, which was causing the activity LED
instead of the link LED to blink for port identification.
Shiraz changes the client interface to not call client close/open on
netdev down/up events, since this causes a lot of thrash that is
not needed. Instead, disable the PE TCP-ENA flag during a netdev
down event and re-enable on a netdev up event, since this blocks all
TCP traffic to the RDMA protocol engine.
Alan fixes an issue which was causing a potential transmit hang by
ignoring the PF link up message if the VF state is not yet in the
RUNNING state.
Amritha fixes the channel VSI recreation during the reset flow to
reconfigure the transmit rings and the queue context associated with
the channel VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If we receive the link status message from PF with link up before queues
are actually enabled, it will trigger a TX hang. This fixes the issue
by ignoring a link up message if the VF state is not yet in RUNNING
state.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40e_init_interrupt_scheme()
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a host disables and enables a PF device, all the associated
VFs are removed and added back in. It also generates a PFR which in turn
resets all the connected VFs. This behaviour is different from that of
Linux guest on Linux host. Hence we end up in a situation where there's
a PFR and device removal at the same time. And watchdog doesn't have a
clue about this and schedules a reset_task. This patch adds code to send
signal to reset_task that the device is currently being removed.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
flush_schedule_work blocks until completion of all scheduled
work items in global work-queue. This can cause deadlock in some
cases. i40evf_remove() cleans up necessary work items with
cancel_delayed_work_sync and cancel_work_sync. This fix removes
flush_schedule_work call inside i40evf_remove().
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
for NVM update
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
With all the support code in place we can now link in the ipsec
offload operations and set the ESP feature flag for the XFRM
subsystem to see.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add a simple statistic to count the ipsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the skb has a security association referenced in the skb, then
set up the Tx descriptor with the ipsec offload bits. While we're
here, we fix an oddly named field in the context descriptor struct.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the chip sees and decrypts an ipsec offload, set up the skb
sp pointer with the ralated SA info. Since the chip is rude
enough to keep to itself the table index it used for the
decryption, we have to do our own table lookup, using the
hash for speed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On a chip reset most of the table contents are lost, so must be
restored. This scans the driver's ipsec tables and restores both
the filled and empty table slots to their pre-reset values.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the functions for setting up and removing offloaded SAs (Security
Associations) with the x540 hardware. We set up the callback structure
but we don't yet set the hardware feature bit to be sure the XFRM service
won't actually try to use us for an offload yet.
The software tables are made up to mimic the hardware tables to make it
easier to track what's in the hardware, and the SA table index is used
for the XFRM offload handle. However, there is a hashing field in the
Rx SA tracking that will be used to facilitate faster table searches in
the Rx fast path.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set up the data structures to be used by the ipsec offload.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add in the code for running and stopping the hardware ipsec
encryption/decryption engine. It is good to keep the engine
off when not in use in order to save on the power draw.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add a few routines to make access to the ipsec registers just a little
easier, and throw in the beginnings of an initialization.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clean up the ipsec/macsec descriptor bit definitions to match the rest
of the defines and file organization. Also recognise the bit-definition
overlap in the error mask macro.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2502:12: error: 'fm10k_suspend' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/fm10k/fm10k_pci.c:2475:12: error: 'fm10k_resume' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 8249c47c6ba4 ("fm10k: use generic PM hooks instead of legacy PCIe power hooks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value. This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This update makes it so that we report the actual number of Tx queues via
real_num_tx_queues but are still restricted to RSS on only the first pool
by setting num_tc equal to 1. Doing this locks us into only having the
ability to setup XPS on the queues in that pool, and only those queues
should be used for transmitting anything other than macvlan traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that instead of bringing rings up/down for various
we just update the netdev pointer for the Rx ring and set or clear the MAC
filter for the interface. By doing it this way we can avoid a number of
races and issues in the code as things were getting messy with the macvlan
clean-up racing with the interface clean-up to bring the rings down on
shutdown.
With this change we opt to leave the rings owned by the PF interface for
both Tx and Rx and just direct the packets once they are received to the
macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We should not be stopping/starting the upper devices Tx queues when
handling a macvlan offload. Instead we should be stopping and starting
traffic on our own queues.
In order to prevent us from doing this I am updating the code so that we no
longer change the queue configuration on the upper device, nor do we update
the queue_index on our own device. Instead we can just use the queue index
for our local device and not update the netdev in the case of the transmit
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
rings
We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.
Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code throughout ixgbe was assuming that dev->num_tc was populated and
configured with the driver, when in fact this can be configured via mqprio
without any hardware coordination other than restricting us to the real
number of Tx queues we advertise.
Instead of handling things this way we need to keep a local copy of the
number of TCs in use so that we don't accidentally pull in the TC
configuration from mqprio when it is configured in software mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We might as well configure the limit to default to 1 pool always for the
interface. This accounts for the fact that the PF counts as 1 pool if
SR-IOV is enabled, and in general we are always running in 1 pool mode when
RSS or DCB is enabled as well, though we don't need to actually evaluate
any of the VMDq features in those cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The macvlan driver itself will validate the MAC address that is configured
for a given interface. There is no need for us to verify it again.
Instead we should be checking to verify that we actually allocate the filter
and have not run out of resources to configure a MAC rule in our filter
table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
track_id == 0 is valid for “read only” profiles when
profile does not have any “write” commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Having the interrupts firing while we are polling causes extra overhead and
isn't needed for most systems out there. If an interrupt is lost us
experiencing a 2s latency spike before recovering is still not acceptable
and masks the issue. We are better off just identifying systems that lose
interrupts and instead enable workarounds for those systems.
To that end I am dropping the code that was strobing the interrupts as
there is a narrow window where having them enabled can actually cause
race issues anyway where a few stray packets might get misses if the
interrupt is re-enabled and fires before we call napi_complete.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If you enabled and disabled promiscuous mode on a VF you could easily put
it into a state where it would start firing interrupts on all queues at a
rate of 50+ interrupts per second even though there was no traffic present.
The issue seems to have been a stray admin queue feature flag set that was
leaving us in a high polling rate for the adminq task.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We should not be clearing the pending bit array for each vector manually.
The documentation for the hardware states that when in MSI-X mode the
pending bit array will be cleared automatically. Us clearing it ourselves
just results in multiple opportunities for us to drop an interrupt.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Variable read_size is initialized and this value is never read, it is
instead set inside the do-loop, hence the initialization is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:390:6: warning: Value stored
to 'read_size' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We introduced the virtchnl interface in order to have an interface for
talking to a virtual device driver which was host-driver agnostic. This
interface has its own definitions, including one for link speed.
The host driver has to talk to the virtchnl interface using these new
definitions in order to remain compatible. Today, the i40e link_speed
enumerations are value-exact matches for the virtchnl interface, so it
was originally decided to simply use a typecast.
However, this is unsafe, and makes it easier for future drivers to
continue this unsafe practice. There is nothing guaranteeing these
values are exact, and the type-cast would hide any compiler warning
which indicates the problem.
Rather than rely on this type cast, introduce a helper function which
can convert the AdminQ link speed definition into a virtchnl
definition. This can then be used by host driver implementations in
order to safely convert to the interface recognized by the virtual
functions.
If the link speed is not able to be represented by the virtchnl
definitions we'll report UNKNOWN which is the safest result.
This will ensure that should the driver specific link_speeds actual bit
definitions change, we do not report them incorrectly according to the
VF.
Additionally, this provides a better pattern for future drivers to copy,
as it is more likely a future device may not use the exact same bit-wise
definition as the current virtchnl interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We currently notify a VF of the link state after ENABLE_QUEUES, which is
the last thing a VF does after being configured. Guests may not actually
ENABLE_QUEUES until they get configured, and thus between driver load
and device configuration the VF may show inaccurate link status.
Fix this by also sending the link state after GET_VF_RESOURCES. Although
we could remove the message following ENABLE_QUEUES, it's not that
significant of a loss, so this patch just keeps both to ensure maximum
compatibility with guests on various OSes.
Specifically, without this patch guests running FreeBSD will display
inaccurate link state until the device is brought up. This is mostly
a cosmetic issue but can be confusing to system administrators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If i40evf_open() is called quickly at the same time as a reset occurs
(such as via ethtool) it is possible for the device to attempt to open
while a reset is in progress. This occurs because the driver was not
holding the critical task bit lock during i40evf_open, nor was it
holding it around the call to i40evf_up_complete() in
i40evf_reset_task().
We didn't hold the lock previously because calls to i40evf_down() would
take the bit lock directly, and this would have caused a deadlock.
To avoid this, we'll move the bit lock handling out of i40evf_down() and
into the callers of this function. Additionally, we'll now hold the bit
lock over the entire set of steps when going up or down, to ensure that
we remain consistent.
Ultimately this causes us to serialize the transitions between down and
up properly, and avoid changing status while we're resetting.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Although not strictly necessary, it is customary to reverse the order in
which we release locks that we acquire. This helps preserve lock
ordering during future refactors, which can help avoid potential
deadlock situations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Stop overloading the __I40EVF_IN_CRITICAL_TASK bit lock to protect the
mac_filter_list and vlan_filter_list. Instead, implement a spinlock to
protect these two lists, similar to how we protect the hash in the i40e
PF code.
Ensure that every place where we access the list uses the spinlock to
ensure consistency, and stop holding the critical section around blocks
of code which only need access to the macvlan filter lists.
This refactor helps simplify the locking behavior, and is necessary as
a future refactor to the __I40EVF_IN_CRITICAL_TASK would cause
a deadlock otherwise.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
