summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/igb/igb_main.c
AgeCommit message (Collapse)Author
2021-05-26igb/igc: use strongly typed pointerJesse Brandeburg
The igb and igc driver both use a trick of creating a local type pointer on the stack to ease dealing with a receive descriptor in 64 bit chunks for printing. Sparse however was not taken into account and receive descriptors are always in little endian order, so just make the unions use __le64 instead of u64. No functional change. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-04-16igb: Redistribute memory for transmit packet buffers when in Qav modeEderson de Souza
i210 has a total of 24KB of transmit packet buffer. When in Qav mode, this buffer is divided into four pieces, one for each Tx queue. Currently, 8KB are given to each of the two SR queues and 4KB are given to each of the two SP queues. However, it was noticed that such distribution can make best effort traffic (which would usually go to the SP queues when Qav is enabled, as the SR queues would be used by ETF or CBS qdiscs for TSN-aware traffic) perform poorly. Using iperf3 to measure, one could see the performance of best effort traffic drop by nearly a third (from 935Mbps to 578Mbps), with no TSN traffic competing. This patch redistributes the 24KB to each queue equally: 6KB each. On tests, there was no notable performance reduction of best effort traffic performance when there was no TSN traffic competing. Below, more details about the data collected: All experiments were run using the following qdisc setup: qdisc taprio 100: root refcnt 9 tc 4 map 3 3 3 2 3 0 0 3 3 3 3 3 3 3 3 3 queues offset 0 count 1 offset 1 count 1 offset 2 count 1 offset 3 count 1 clockid TAI base-time 0 cycle-time 10000000 cycle-time-extension 0 index 0 cmd S gatemask 0xf interval 10000000 qdisc etf 8045: parent 100:1 clockid TAI delta 1000000 offload on deadline_mode off skip_sock_check off TSN traffic, when enabled, had this characteristics: Packet size: 1500 bytes Transmission interval: 125us ---------------------------------- Without this patch: ---------------------------------- - TCP data: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.35 GBytes 578 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.07 GBytes 460 Mbits/sec 1 - TCP data limiting iperf3 buffer size to 4K: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.35 GBytes 579 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.08 GBytes 462 Mbits/sec 0 - TCP data limiting iperf3 buffer size to 192 bytes (smallest size without serious performance degradation): - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.34 GBytes 577 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.07 GBytes 461 Mbits/sec 1 - UDP data at 1000Mbit/sec: - No TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.36 GBytes 586 Mbits/sec 0.000 ms 0/1011407 (0%) - With TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.05 GBytes 451 Mbits/sec 0.000 ms 0/778672 (0%) ---------------------------------- With this patch: ---------------------------------- - TCP data: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 646 Mbits/sec 1 - TCP data limiting iperf3 buffer size to 4K: - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 931 Mbits/sec 0 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0 - TCP data limiting iperf3 buffer size to 192 bytes (smallest size without serious performance degradation): - No TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 2.17 GBytes 932 Mbits/sec 1 - With TSN traffic: [ ID] Interval Transfer Bitrate Retr [ 5] 0.00-20.00 sec 1.50 GBytes 645 Mbits/sec 0 - UDP data at 1000Mbit/sec: - No TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 2.23 GBytes 956 Mbits/sec 0.000 ms 0/1650226 (0%) - With TSN traffic: [ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams [ 5] 0.00-20.00 sec 1.51 GBytes 649 Mbits/sec 0.000 ms 0/1120264 (0%) Signed-off-by: Ederson de Souza <ederson.desouza@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-25Merge https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller
Alexei Starovoitov says: ==================== pull-request: bpf-next 2021-03-24 The following pull-request contains BPF updates for your *net-next* tree. We've added 37 non-merge commits during the last 15 day(s) which contain a total of 65 files changed, 3200 insertions(+), 738 deletions(-). The main changes are: 1) Static linking of multiple BPF ELF files, from Andrii. 2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo. 3) Spelling fixes from various folks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-23intel: clean up mismatched header commentsJesse Brandeburg
A bunch of header comments were showing warnings when compiling with W=1. Fix them all at once. This changes only comments. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-19igb: check timestamp validityJesse Brandeburg
Add a couple of checks to make sure timestamping is on and that the timestamp value from DMA is valid. This avoids any functional issues that could come from a misinterpreted time stamp. One of the functions changed doesn't need a return value added because there was no value in checking from the calling locations. While here, fix a couple of reverse christmas tree issues next to the code being changed. Fixes: f56e7bba22fa ("igb: Pull timestamp from fragment before adding it to skb") Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-18bpf, devmap: Move drop error path to devmap for XDP_REDIRECTLorenzo Bianconi
We want to change the current ndo_xdp_xmit drop semantics because it will allow us to implement better queue overflow handling. This is working towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error path handling from each XDP ethernet driver to devmap code. According to the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx loop whenever the hw reports a tx error and it will just return to devmap caller the number of successfully transmitted frames. It will be devmap responsibility to free dropped frames. Move each XDP ndo_xdp_xmit capable driver to the new APIs: - veth - virtio-net - mvneta - mvpp2 - socionext - amazon ena - bnxt - freescale (dpaa2, dpaa) - xen-frontend - qede - ice - igb - ixgbe - i40e - mlx5 - ti (cpsw, cpsw-new) - tun - sfc Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Camelia Groza <camelia.groza@nxp.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
2021-03-15net: ethernet: intel: igb: Typo fix in the file igb_main.cBhaskar Chowdhury
s/structue/structure/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-12igb: avoid premature Rx buffer reuseLi RongQing
Igb needs a similar fix as commit 75aab4e10ae6a ("i40e: avoid premature Rx buffer reuse") The page recycle code, incorrectly, relied on that a page fragment could not be freed inside xdp_do_redirect(). This assumption leads to that page fragments that are used by the stack/XDP redirect can be reused and overwritten. To avoid this, store the page count prior invoking xdp_do_redirect(). Longer explanation: Intel NICs have a recycle mechanism. The main idea is that a page is split into two parts. One part is owned by the driver, one part might be owned by someone else, such as the stack. t0: Page is allocated, and put on the Rx ring +--------------- used by NIC ->| upper buffer (rx_buffer) +--------------- | lower buffer +--------------- page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX t1: Buffer is received, and passed to the stack (e.g.) +--------------- | upper buff (skb) +--------------- used by NIC ->| lower buffer (rx_buffer) +--------------- page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX - 1 t2: Buffer is received, and redirected +--------------- | upper buff (skb) +--------------- used by NIC ->| lower buffer (rx_buffer) +--------------- Now, prior calling xdp_do_redirect(): page count == USHRT_MAX rx_buffer->pagecnt_bias == USHRT_MAX - 2 This means that buffer *cannot* be flipped/reused, because the skb is still using it. The problem arises when xdp_do_redirect() actually frees the segment. Then we get: page count == USHRT_MAX - 1 rx_buffer->pagecnt_bias == USHRT_MAX - 2 From a recycle perspective, the buffer can be flipped and reused, which means that the skb data area is passed to the Rx HW ring! To work around this, the page count is stored prior calling xdp_do_redirect(). Fixes: 9cbc948b5a20 ("igb: add XDP support") Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-03-10net: add a helper to avoid issues with HW TX timestamping and SO_TXTIMEVladimir Oltean
As explained in commit 29d98f54a4fe ("net: enetc: allow hardware timestamping on TX queues with tc-etf enabled"), hardware TX timestamping requires an skb with skb->tstamp = 0. When a packet is sent with SO_TXTIME, the skb->skb_mstamp_ns corrupts the value of skb->tstamp, so the drivers need to explicitly reset skb->tstamp to zero after consuming the TX time. Create a helper named skb_txtime_consumed() which does just that. All drivers which offload TC_SETUP_QDISC_ETF should implement it, and it would make it easier to assess during review whether they do the right thing in order to be compatible with hardware timestamping or not. Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-04Merge branch '1GbE' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue Tony Nguyen says: ==================== 1GbE Intel Wired LAN Driver Updates 2021-02-03 This series contains updates to igc, igb, e1000e, and e1000 drivers. Sasha adds counting of good transmit packets and reporting of NVM version and gPHY version in ethtool firmware version. Replaces the use of strlcpy to the preferred strscpy. Fixes a typo that caused the wrong register to be output. He also removes an unused function pointer, some unneeded defines, and a non-applicable comment. All changes for igc. Gal Hammer fixes a typo which caused the RDBAL register values to be shown instead of TDBAL for igb. Nick Lowe enables RSS support for i211 devices for igb. Tom Rix fixes checkpatch warning by removing h from printk format specifier for igb. Kaixu Xia removes setting of a variable that is overwritten before next use for e1000e. Sudip Mukherjee removes an unneeded assignment for e1000. * '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: e1000: drop unneeded assignment in e1000_set_itr() e1000e: remove the redundant value assignment in e1000_update_nvm_checksum_spt igb: remove h from printk format specifier igb: Enable RSS for Intel I211 Ethernet Controller igb: fix TDBAL register show incorrect value igc: Fix TDBAL register show incorrect value igc: Remove unused FUNC_1 mask igc: Remove unused local receiver mask igc: Prefer strscpy over strlcpy igc: Expose the gPHY firmware version igc: Expose the NVM version igc: Add Host Good Packets Transmitted Count igc: Remove MULR mask define igc: Remove igc_set_fw_version comment igc: Clean up nvm_operations structure ==================== Link: https://lore.kernel.org/r/20210204004259.3662059-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-04net: use the new dev_page_is_reusable() instead of private versionsAlexander Lobakin
Now we can remove a bunch of identical functions from the drivers and make them use common dev_page_is_reusable(). All {,un}likely() checks are omitted since it's already present in this helper. Also update some comments near the call sites. Suggested-by: David Rientjes <rientjes@google.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Cc: John Hubbard <jhubbard@nvidia.com> Signed-off-by: Alexander Lobakin <alobakin@pm.me> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-03igb: remove h from printk format specifierTom Rix
This change fixes the checkpatch warning described in this commit cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]") Standard integer promotion is already done and %hx and %hhx is useless so do not encourage the use of %hh[xudi] or %h[xudi]. Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-02-03igb: Enable RSS for Intel I211 Ethernet ControllerNick Lowe
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS) queues. It should not be excluded from having this feature enabled. Via commit c883de9fd787 ("igb: rename igb define to be more generic") E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to indicate that this is a generic bit flag to enable queues and not a flag that is specific to devices that support 4 queues The bit flag enables 2, 4 or 8 queues appropriately depending on the part. Tested with a multicore CPU and frames were then distributed as expected. This issue appears to have been introduced because of confusion caused by the prior name. Signed-off-by: Nick Lowe <nick.lowe@gmail.com> Tested-by: David Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-02-03igb: fix TDBAL register show incorrect valueGal Hammer
Fixed a typo which caused the registers dump function to read the RDBAL register when printing TDBAL register values. Signed-off-by: Gal Hammer <ghammer@redhat.com> Tested-by: David Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2021-01-19net: igb: use skb_csum_is_sctp instead of protocol checkXin Long
Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC checksum offload packet, and there is no need to parse the packet to check its proto field, especially when it's a UDP or GRE encapped packet. So this patch also makes igb support SCTP CRC checksum offload for UDP and GRE encapped packets. Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-08net, xdp: Introduce xdp_prepare_buff utility routineLorenzo Bianconi
Introduce xdp_prepare_buff utility routine to initialize per-descriptor xdp_buff fields (e.g. xdp_buff pointers). Rely on xdp_prepare_buff() in all XDP capable drivers. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Acked-by: Camelia Groza <camelia.groza@nxp.com> Acked-by: Marcin Wojtas <mw@semihalf.com> Link: https://lore.kernel.org/bpf/45f46f12295972a97da8ca01990b3e71501e9d89.1608670965.git.lorenzo@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2021-01-08net, xdp: Introduce xdp_init_buff utility routineLorenzo Bianconi
Introduce xdp_init_buff utility routine to initialize xdp_buff fields const over NAPI iterations (e.g. frame_sz or rxq pointer). Rely on xdp_init_buff in all XDP capable drivers. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Acked-by: Camelia Groza <camelia.groza@nxp.com> Acked-by: Marcin Wojtas <mw@semihalf.com> Link: https://lore.kernel.org/bpf/7f8329b6da1434dc2b05a77f2e800b29628a8913.1608670965.git.lorenzo@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
2020-12-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
xdp_return_frame_bulk() needs to pass a xdp_buff to __xdp_return(). strlcpy got converted to strscpy but here it makes no functional difference, so just keep the right code. Conflicts: net/netfilter/nf_tables_api.c Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-09igb: avoid transmit queue timeout in xdp pathSven Auhagen
Since we share the transmit queue with the network stack, it is possible that we run into a transmit queue timeout. This will reset the queue. This happens under high load when XDP is using the transmit queue pretty much exclusively. netdev_start_xmit() sets the trans_start variable of the transmit queue to jiffies which is later utilized by dev_watchdog(), so to avoid timeout, let stack know that XDP xmit happened by bumping the trans_start within XDP Tx routines to jiffies. Fixes: 9cbc948b5a20 ("igb: add XDP support") Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09igb: use xdp_do_flushSven Auhagen
Since it is a new XDP implementation change xdp_do_flush_map to xdp_do_flush. Fixes: 9cbc948b5a20 ("igb: add XDP support") Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09igb: skb add metasize for xdpSven Auhagen
add metasize if it is set in xdp Fixes: 9cbc948b5a20 ("igb: add XDP support") Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09igb: XDP extack message on errorSven Auhagen
Add an extack error message when the RX buffer size is too small for the frame size. Fixes: 9cbc948b5a20 ("igb: add XDP support") Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09igb: take VLAN double header into accountSven Auhagen
Increase the packet header padding to include double VLAN tagging. This patch uses a macro for this. Fixes: 9cbc948b5a20 ("igb: add XDP support") Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-09igb: XDP xmit back fix error codeSven Auhagen
The igb XDP xmit back function should only return defined error codes. Fixes: 9cbc948b5a20 ("igb: add XDP support") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-12-01xsk: Propagate napi_id to XDP socket Rx pathBjörn Töpel
Add napi_id to the xdp_rxq_info structure, and make sure the XDP socket pick up the napi_id in the Rx path. The napi_id is used to find the corresponding NAPI structure for socket busy polling. Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
2020-09-29net: intel: Remove in_interrupt() warningsSebastian Andrzej Siewior
in_interrupt() is ill defined and does not provide what the name suggests. The usage especially in driver code is deprecated and a tree wide effort to clean up and consolidate the (ab)usage of in_interrupt() and related checks is happening. In this case the checks cover only parts of the contexts in which these functions cannot be called. They fail to detect preemption or interrupt disabled invocations. As the functions which are invoked from the various places contain already a broad variety of checks (always enabled or debug option dependent) cover all invalid conditions already, there is no point in having inconsistent warnings in those drivers. Just remove them. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-28igb: read PBA number from flashGal Hammer
Fixed flash presence check for 82576 controllers so the part number string is read and displayed correctly. Signed-off-by: Gal Hammer <ghammer@redhat.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-28igb: add XDP supportSven Auhagen
Add XDP support to the IGB driver. The implementation follows the IXGBE XDP implementation closely and I used the following patches as basis: 1. commit 924708081629 ("ixgbe: add XDP support for pass and drop actions") 2. commit 33fdc82f0883 ("ixgbe: add support for XDP_TX action") 3. commit ed93a3987128 ("ixgbe: tweak page counting for XDP_REDIRECT") Due to the hardware constraints of the devices using the IGB driver we must share the TX queues with XDP which means locking the TX queue for XDP. I ran tests on an older device to get better numbers. Test machine: Intel(R) Atom(TM) CPU C2338 @ 1.74GHz (2 Cores) 2x Intel I211 Routing Original Driver Network Stack: 382 Kpps Routing XDP Redirect (xdp_fwd_kern): 1.48 Mpps XDP Drop: 1.48 Mpps Using XDP we can achieve line rate forwarding even on an older Intel Atom CPU. Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-09-25intel-ethernet: clean up W=1 warnings in kdocJesse Brandeburg
This takes care of all of the trivial W=1 fixes in the Intel Ethernet drivers, which allows developers and maintainers to build more of the networking tree with more complete warning checks. There are three classes of kdoc warnings fixed: - cannot understand function prototype: 'x' - Excess function parameter 'x' description in 'y' - Function parameter or member 'x' not described in 'y' All of the changes were trivial comment updates on function headers. Inspired by Lee Jones' series of wireless work to do the same. Compile tested only, and passes simple test of $ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \ xargs scripts/kernel-doc -none Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
We got slightly different patches removing a double word in a comment in net/ipv4/raw.c - picked the version from net. Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached values instead of VNIC login response buffer (following what commit 507ebe6444a4 ("ibmvnic: Fix use-after-free of VNIC login response buffer") did). Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-08-26net: Take common prefetch code structure into a functionTariq Toukan
Many device drivers use the same prefetch code structure to deal with small L1 cacheline size. Take this code into a function and call it from the drivers. Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Resolved kernel/bpf/btf.c using instructions from merge commit 69138b34a7248d2396ab85c8652e20c0c39beaba Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-30igb: use eth_zero_addr() to clear mac addressMiaohe Lin
Use eth_zero_addr() to clear mac address instead of memset(). Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-30igb: reinit_locked() should be called with rtnl_lockFrancesco Ruggeri
We observed two panics involving races with igb_reset_task. The first panic is caused by this race condition: kworker reboot -f igb_reset_task igb_reinit_locked igb_down napi_synchronize __igb_shutdown igb_clear_interrupt_scheme igb_free_q_vectors igb_free_q_vector adapter->q_vector[v_idx] = NULL; napi_disable Panics trying to access adapter->q_vector[v_idx].napi_state The second panic (a divide error) is caused by this race: kworker reboot -f tx packet igb_reset_task __igb_shutdown rtnl_lock() ... igb_clear_interrupt_scheme igb_free_q_vectors adapter->num_tx_queues = 0 ... rtnl_unlock() rtnl_lock() igb_reinit_locked igb_down igb_up netif_tx_start_all_queues dev_hard_start_xmit igb_xmit_frame igb_tx_queue_mapping Panics on r_idx % adapter->num_tx_queues This commit applies to igb_reset_task the same changes that were applied to ixgbe in commit 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver"), commit 8f4c5c9fb87a ("ixgbe: reinit_locked() should be called with rtnl_lock") and commit 88adce4ea8f9 ("ixgbe: fix possible race in reset subtask"). Signed-off-by: Francesco Ruggeri <fruggeri@arista.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-07-01ethernet/intel: Convert fallthrough code commentsJeff Kirsher
Convert all the remaining 'fall through" code comments to the newer 'fallthrough;' keyword. Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2020-06-25net/intel: remove driver versions from Intel driversJeff Kirsher
As with other networking drivers, remove the unnecessary driver version from the Intel drivers. The ethtool driver information and module version will then report the kernel version instead. For ixgbe, i40e and ice drivers, the driver passes the driver version to the firmware to confirm that we are up and running. So we now pass the value of UTS_RELEASE to the firmware. This adminq call is required per the HAS document. The Device then sends an indication to the BMC that the PF driver is present. This is done using Host NC Driver Status Indication in NC-SI Get Link command or via the Host Network Controller Driver Status Change AEN. What the BMC may do with this information is implementation-dependent, but this is a standard NC-SI 1.1 command we honor per the HAS. CC: Bruce Allan <bruce.w.allan@intel.com> CC: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: Alek Loktionov <aleksandr.loktionov@intel.com> CC: Kevin Liedtke <kevin.d.liedtke@intel.com> CC: Aaron Rowden <aaron.f.rowden@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Co-developed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com>
2020-04-24PM: sleep: core: Rename DPM_FLAG_NEVER_SKIPRafael J. Wysocki
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which matches its purpose more closely. No functional impact. Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alex Deucher <alexander.deucher@amd.com>
2019-12-31igb: dont drop packets if rx flow control is enabledRobert Beckett
If Rx flow control has been enabled (via autoneg or forced), packets should not be dropped due to Rx descriptor ring exhaustion. Instead pause frames should be used to apply back pressure. This only applies if VFs are not in use. Move SRRCTL setup to its own function for easy reuse and only set drop enable bit if Rx flow control is not enabled. Since v1: always enable dropping of packets if VFs in use. Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-12-12netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin
This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
One conflict in the BPF samples Makefile, some fixes in 'net' whilst we were converting over to Makefile.target rules in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-08igb/igc: use ktime accessors for skb->tstampJacob Keller
When implementing launch time support in the igb and igc drivers, the skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t value. Although ktime_t is typedef'd to s64 it wasn't always, and the kernel provides accessors for ktime_t values. Use the ktime_to_timespec64 and ktime_set accessors instead of directly assuming that the variable is always an s64. This improves portability if the code is ever moved to another kernel version, or if the definition of ktime_t ever changes again in the future. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-11-07net: ethernet: intel: Demote MTU change prints to debugFlorian Fainelli
Changing a network device MTU can be a fairly frequent operation, and failure to change the MTU is reflected to user-space properly, both by an appropriate message as well as by looking at whether the device's MTU matches the configuration. Demote the prints to debug prints by using netdev_dbg(), making all Intel wired LAN drivers consistent, since they used a mixture of PCI device and network device prints before. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
The only slightly tricky merge conflict was the netdevsim because the mutex locking fix overlapped a lot of driver reload reorganization. The rest were (relatively) trivial in nature. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-01igb: Fix constant media auto sense switching when no cable is connectedManfred Rudigier
At least on the i350 there is an annoying behavior that is maybe also present on 82580 devices, but was probably not noticed yet as MAS is not widely used. If no cable is connected on both fiber/copper ports the media auto sense code will constantly swap between them as part of the watchdog task and produce many unnecessary kernel log messages. The swap code responsible for this behavior (switching to fiber) should not be executed if the current media type is copper and there is no signal detected on the fiber port. In this case we can safely wait until the AUTOSENSE_EN bit is cleared. Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-31igb: Enable media autosense for the i350.Manfred Rudigier
This patch enables the hardware feature "Media Auto Sense" also on the i350. It works in the same way as on the 82850 devices. Hardware designs using dual PHYs (fiber/copper) can enable this feature by setting the MAS enable bits in the NVM_COMPAT register (0x03) in the EEPROM. Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-31igb/igc: Don't warn on fatal read failures when the device is removedLyude Paul
Fatal read errors are worth warning about, unless of course the device was just unplugged from the machine - something that's a rather normal occurrence when the igb/igc adapter is located on a Thunderbolt dock. So, let's only WARN() if there's a fatal read error while the device is still present. This fixes the following WARN splat that's been appearing whenever I unplug my Caldigit TS3 Thunderbolt dock from my laptop: igb 0000:09:00.0 enp9s0: PCIe link lost ------------[ cut here ]------------ igb: Failed to read reg 0x18! WARNING: CPU: 7 PID: 516 at drivers/net/ethernet/intel/igb/igb_main.c:756 igb_rd32+0x57/0x6a [igb] Modules linked in: igb dca thunderbolt fuse vfat fat elan_i2c mei_wdt mei_hdcp i915 wmi_bmof intel_wmi_thunderbolt iTCO_wdt iTCO_vendor_support x86_pkg_temp_thermal intel_powerclamp joydev coretemp crct10dif_pclmul crc32_pclmul i2c_algo_bit ghash_clmulni_intel intel_cstate drm_kms_helper intel_uncore syscopyarea sysfillrect sysimgblt fb_sys_fops intel_rapl_perf intel_xhci_usb_role_switch mei_me drm roles idma64 i2c_i801 ucsi_acpi typec_ucsi mei intel_lpss_pci processor_thermal_device typec intel_pch_thermal intel_soc_dts_iosf intel_lpss int3403_thermal thinkpad_acpi wmi int340x_thermal_zone ledtrig_audio int3400_thermal acpi_thermal_rel acpi_pad video pcc_cpufreq ip_tables serio_raw nvme nvme_core crc32c_intel uas usb_storage e1000e i2c_dev CPU: 7 PID: 516 Comm: kworker/u16:3 Not tainted 5.2.0-rc1Lyude-Test+ #14 Hardware name: LENOVO 20L8S2N800/20L8S2N800, BIOS N22ET35W (1.12 ) 04/09/2018 Workqueue: kacpi_hotplug acpi_hotplug_work_fn RIP: 0010:igb_rd32+0x57/0x6a [igb] Code: 87 b8 fc ff ff 48 c7 47 08 00 00 00 00 48 c7 c6 33 42 9b c0 4c 89 c7 e8 47 45 cd dc 89 ee 48 c7 c7 43 42 9b c0 e8 c1 94 71 dc <0f> 0b eb 08 8b 00 ff c0 75 b0 eb c8 44 89 e0 5d 41 5c c3 0f 1f 44 RSP: 0018:ffffba5801cf7c48 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff9e7956608840 RCX: 0000000000000007 RDX: 0000000000000000 RSI: ffffba5801cf7b24 RDI: ffff9e795e3d6a00 RBP: 0000000000000018 R08: 000000009dec4a01 R09: ffffffff9e61018f R10: 0000000000000000 R11: ffffba5801cf7ae5 R12: 00000000ffffffff R13: ffff9e7956608840 R14: ffff9e795a6f10b0 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff9e795e3c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000564317bc4088 CR3: 000000010e00a006 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: igb_release_hw_control+0x1a/0x30 [igb] igb_remove+0xc5/0x14b [igb] pci_device_remove+0x3b/0x93 device_release_driver_internal+0xd7/0x17e pci_stop_bus_device+0x36/0x75 pci_stop_bus_device+0x66/0x75 pci_stop_bus_device+0x66/0x75 pci_stop_and_remove_bus_device+0xf/0x19 trim_stale_devices+0xc5/0x13a ? __pm_runtime_resume+0x6e/0x7b trim_stale_devices+0x103/0x13a ? __pm_runtime_resume+0x6e/0x7b trim_stale_devices+0x103/0x13a acpiphp_check_bridge+0xd8/0xf5 acpiphp_hotplug_notify+0xf7/0x14b ? acpiphp_check_bridge+0xf5/0xf5 acpi_device_hotplug+0x357/0x3b5 acpi_hotplug_work_fn+0x1a/0x23 process_one_work+0x1a7/0x296 worker_thread+0x1a8/0x24c ? process_scheduled_works+0x2c/0x2c kthread+0xe9/0xee ? kthread_destroy_worker+0x41/0x41 ret_from_fork+0x35/0x40 ---[ end trace 252bf10352c63d22 ]--- Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 47e16692b26b ("igb/igc: warn when fatal read failure happens") Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Acked-by: Feng Tang <feng.tang@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-10-29igb: Add UDP segmentation offload supportJosh Hunt
Based on a series from Alexander Duyck this change adds UDP segmentation offload support to the igb driver. CC: Alexander Duyck <alexander.h.duyck@intel.com> CC: Willem de Bruijn <willemb@google.com> Signed-off-by: Josh Hunt <johunt@akamai.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2019-08-22ethernet: Delete unnecessary checks before the macro call “dev_kfree_skb”Markus Elfring
The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>