summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/i40evf
AgeCommit message (Collapse)Author
2016-05-20intel: Add support for IPv6 IP-in-IP offloadAlexander Duyck
This patch adds support for offloading IPXIP6 type packets that represent either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In addition with this change we should also be able to support FOU encapsulated traffic with outer IPv6 headers. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-20net: define gso types for IPx over IPv4 and IPv6Tom Herbert
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and NETIF_F_GSO_IPXIP6. These are used to described IP in IP tunnel and what the outer protocol is. The inner protocol can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT are removed (these are both instances of SKB_GSO_IPXIP4). SKB_GSO_IPXIP6 will be used when support for GSO with IP encapsulation over IPv6 is added. Signed-off-by: Tom Herbert <tom@herbertland.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-13i40e: Add allmulti support for the VFAnjali Singhai Jain
This patch enables a feature to enable/disable all multicast for a trusted VF. Change-Id: I926eba7f8850c8d40f8ad7e08bbe4056bbd3985f Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40evf: Allocate Rx buffers properlyMitch Williams
Allocate the correct number of RX buffers, and don't fiddle with next_to_use. The common RX code handles all of this. This fixes a memory leak of one page each time the driver is opened. Change-Id: Id06eca353086e084921f047acad28c14745684ee Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40e/i40evf: Remove unused hardware receive descriptor codeJesse Brandeburg
The hardware supports a 16 byte descriptor for receive, but the driver was never using it in production. There was no performance benefit to the real driver of 16 byte descriptors, so drop a whole lot of complexity while getting rid of the code. Also since the previous patch made us use no-split mode all the time, drop any support in the driver for any other value in dtype and assume it is always zero (aka no-split). Hooray for code removal! Change-ID: I2257e902e4dad84a07b94db6d2e6f4ce69b27bc0 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40evf: refactor receive routineJesse Brandeburg
This is part 2 of the Rx refactor series, just including changes to i40evf. This refactor aligns the receive routine with the one in ixgbe which was highly optimized. This reduces the code we have to maintain and allows for (hopefully) more readable and maintainable RX hot path. In order to do this: - consolidate the receive path into a single function that doesn't use packet split but *does* use pages for Rx buffers. - remove the old _1buf routine - consolidate several routines into helper functions - remove VF ethtool control over packet split - remove priv_flags interface since it is unused Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40evf: Drop packet split receive routineJesse Brandeburg
As part of preparation for the rx-refactor, remove the packet split receive routine and ancillary code. Some of the split related context set up code stays in i40e_virtchnl_pf.c in case an older VF driver tries to load and still wants to use packet split. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40e/i40evf: Remove reference to ring->dtypeJesse Brandeburg
As part of the rx-refactor, the dtype variable in the i40e_ring struct is no longer used, so remove it. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-05i40e/i40evf: Refactor tunnel interpretationJesse Brandeburg
Refactor the interpretation of a tunnel. This removes some code and lets us start using the hardware's parsing. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40e/i40evf: Add support for GSO partial with UDP_TUNNEL_CSUM and GRE_CSUMAlexander Duyck
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support segmentation for frames with checksums enabled in outer headers. As a result we can now send data over these types of tunnels at over 20Gb/s versus the 12Gb/s that was previously possible on my system. The advantage with the i40e parts is that this offload is mostly transparent as the hardware still deals with the inner and/or outer IPv4 headers so the IP ID is still incrementing for both when this offload is performed. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40evf: make use of BIT() macro to avoid signed left shiftJacob Keller
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40e/i40evf: fix I40E_MASK signed shift overflow warningsJacob Keller
GCC 6 has a new warning which will display when you attempt to left shift a signed value beyond the storage size of the type. I40E_MASK generates a mask value for 32bit registers. Properly typecast the mask value and place the values in parenthesis to prevent macro expansion issues. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40e/i40evf : Bump driver version from 1.5.5 to 1.5.10Harshitha Ramamurthy
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40evf: RSS Hash Option parametersCarolyn Wyborny
This patch syncs the VF code for the changes made to the PF for the RSS hash tuple settings. Since the VF still cannot change the RSS hash settings, change the code to make this clear to the user. Previously, the default settings were returned in this function. However, the default can be changed by the PF so this does not make sense anymore. Change-Id: I085eaf005fc7978b440d2a1bf2b2dd7cadaff39b Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-01i40e: Remove HMC AQ API implementationNeerav Parikh
Remove the code that implements the HMC AQ APIs and call these APIs. This is done because these are obsolete APIs and are not supported by firmware. Change-ID: I5d771d8f37c3e16e7b0a972ff9b27e75aa2d05d4 Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-27i40evf: Add driver support for promiscuous modeAnjali Singhai Jain
Add necessary Linux Ethernet driver support for promiscuous mode operation. Add a flag so the VF knows it is in promiscuous mode and two state flags to discreetly track multicast and unicast promiscuous states. Change-Id: Ib2f2dc7a7582304fec90fc917ebb7ded21ba1de4 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-27i40e/i40evf: Only offload VLAN tag if enabledJesse Brandeburg
The driver was offloading the VLAN tag into the skb any time there was a VLAN tag and the hardware stripping was enabled. Just check to make sure it's enabled before put_tag. Change-Id: Ife95290c06edd9a616393b38679923938b382241 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-27i40e: Add DeviceID for X722 QSFP+Kamil Krawczyk
Change-ID: I1370fbc7774e815ac1ad56561e97488e829592fc Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-27i40e: Add device capability which defines if update is availableMichal Kosiarz
Add device capability which defines if update is available and security check is needed during update process. Change-ID: I380787c878275e1df18b39198df3ee3666342282 Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-26i40evf: Allow PF driver to configure RSSMitch Williams
If the PF driver reports proper support, allow the PF driver to configure RSS on the behalf of the VF driver. This will allow for RSS support on future hardware without changes to the VF driver. Unfortunately, the old RSS code still needs to stay as the driver needs to be compatible with PF drivers that don't support this interface. But this change still simplifies the data structures a bunch and makes this code simpler to read and maintain. Change-ID: I0375aad40788ecdc0cb24d5cfeccf07804e69771 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-26i40e: Specify AQ event opcode to wait forShannon Nelson
To add a little flexibility to the nvmupdate facility, this code adds the ability to specify an AQ event opcode to wait on after the Exec_AQ request. Change-ID: Iddbfd63c3de8df3edb9d3e90678b08989bc4946e Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-26i40evf: Don't PanicMitch Williams
Under some circumstances the driver remove function may be called before the driver is fully initialized. So we can't assume that we know where our towel is at, or that all of the data structures are initialized. To ensure that we don't panic, check that the vsi_res pointer is valid before dereferencing it. Then drink beer and eat peanuts. Change-ID: If697b4db57348e39f9538793e16aa755e3e1af03 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-26i40e/i40evf: Add support for IPIP and SIT offloadsAlexander Duyck
Looking over the documentation it turns out enabling IPIP and SIT offloads for i40e is pretty straightforward. As such I decided to enable them with this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s for IPIP and SIT tunnels with this offload enabled. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-26i40e/i40evf: Clean up feature flagsAlexander Duyck
The feature flags list for i40e and i40evf is beginning to become pretty massive. I plan to add another 4 or so features to these drivers and duplicating the flags for each and every flags list is becoming a bit repetitive. The primary change here is that we now build our features list around hw_encap_features. After that we assign that to vlan_features, hw_features, and finally map that onto features. In addition we end up throwing features onto hw_encap_features that end up having no effect such as the Rx offloads and SCTP_CRC. However that should have no impact and makes things a bit easier for us as hw_encap_features is one of the less updated features maps available. For i40evf I went through and sanity checked a few features as well. Specifically RXCSUM was being set as a read-only feature which didn't make much sense. I have updated things so we can clear the NETIF_F_RXCSUM flag since that is really a software feature and not a hardware one anyway so disabling it is just a matter of ignoring the result from the hardware. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts were two cases of simple overlapping changes, nothing serious. In the UDP case, we need to add a hlist_add_tail_rcu() to linux/rculist.h, because we've moved UDP socket handling away from using nulls lists. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-04-13i40e/i40evf: Limit TSO to 7 descriptors for payload instead of 8 per packetAlexander Duyck
This patch addresses a bug introduced based on my interpretation of the XL710 datasheet. Specifically section 8.4.1 states that "A single transmit packet may span up to 8 buffers (up to 8 data descriptors per packet including both the header and payload buffers)." It then later goes on to say that each segment for a TSO obeys the previous rule, however it then refers to TSO header and the segment payload buffers. I believe the actual limit for fragments with TSO and a skbuff that has payload data in the header portion of the buffer is actually only 7 fragments as the skb->data portion counts as 2 buffers, one for the TSO header, and one for a segment payload buffer. Fixes: 2d37490b82af ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check") Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40evf: properly handle VLAN featuresMitch Williams
Correctly set the VLAN feature flags after setting the rest of the netdev flags. And don't set them in hw_features, because these can't be controlled by the VF driver. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e/i40evf: Bump patch from 1.5.2 to 1.5.5Harshitha Ramamurthy
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e: Input set mask constants for RSS, flow director, and flex bytesKiran Patil
Add defines for input set mask (RSS, flow director, flexible payload), including defines specific to IPv6. Change-ID: Ie95ef7d0916a4d6ca011c194283f959774c8dce9 Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e: Add RSS configuration to virtual channelMitch Williams
Add opcodes and structures to support RSS configuration by PF driver on behalf of the VF drivers. This reduces complexity in the VF driver and allows us to support future hardware designs without modifying the VF driver. Change-ID: I8c75765c630eacb71f95967f1109a198542593ac Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e: Move NVM variable out of AQ structShannon Nelson
The NVM update status info should stay collected together, not spread across different structs. Change-ID: Ic16f9e9fd79945d865bb7226184c889884585025 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e/i40evf: Faster RX via avoiding FCoEJesse Brandeburg
As it turns out, calling into other files from hot path hurts performance a lot. In this case the majority of the time we call "check FCoE" and the packet is *not* FCoE, but this call was taking 5% of our total cycles spent on receive. Change-ID: I080552c26e7060bc7b78504dc2763f6f0b3d8c76 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e/i40evf: Drop unused tx_ring argumentJesse Brandeburg
Some of the tx_ring arguments can be deleted since they are not used. Change-ID: I99275b0f191d7f63ec2f05061919904940c36f31 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-06i40e/i40evf: Move stack var deeperJesse Brandeburg
A local variable could move down inside the context where it is used. Change-ID: I9caba9e1eacf921037077f2665cbce83fd8e95d6 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Fix TSO checksum pseudo-header adjustmentAlexander Duyck
With IPv4 and IPv6 now using the same format for checksums based on the length of the frame we need to update the i40e and i40evf drivers so that they correctly account for lengths greater than or equal to 64K. With this patch the driver should now correctly update checksums for frames up to 16776960 in length which should be more than large enough for all possible TSO frames in the near future. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Bump patch from 1.5.1 to 1.5.2Avinash Dayanand
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40evf: Fix get_rss_aqCatherine Sullivan
We were passing in the seed where we should just be passing false because we want the VSI table not the pf table. Change-ID: I9b633ab06eb59468087f0c0af8539857e99f9495 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40evf: Add longer wait after remove moduleMitch Williams
Upon module remove, wait a little longer after requesting a reset before checking to see if the firmware responded. This change prevents double resets when the firmware is busy. Change-ID: Ieedc988ee82fac1f32a074bf4d9e4dba426bfa58 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e: Add new device ID for X722Catherine Sullivan
The new device ID is 0x37D3 and it should follow the same flows and branding string as for 0x37D0. Change-ID: Ia5ad4a1910268c4666a3fd46a7afffbec55b4fc2 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40evf: Fix VLAN featuresMitch Williams
Users of ethtool were being given the mistaken impression that this driver was able to change its VLAN tagging features, and were disappointed that this was not actually the case. Implement ndo_fix_features method so that we can adjust these flags as needed to avoid false impressions. Change-ID: I08584f103a4fa73d6a4128d472e4ef44dcfda57f Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Bump patch from 1.4.25 to 1.5.1Catherine Sullivan
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40evf: Add additional check for resetMitch Williams
If the driver happens to read a register during the time in which the device is undergoing reset, it will receive a value of 0xdeadbeef instead of a valid value. Unfortunately, the driver may misinterpret this as a valid value, especially if it's just looking for individual bits. Add an explicit check for this value when we are looking for admin queue errors, and trigger reset recovery if we find it. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Fix casting in transmit codeJesse Brandeburg
Simple cast to fix a sparse warning. Fixes: commit 5453205cd097 ("i40e/i40evf: Enable support for SKB_GSO_UDP_TUNNEL_CSUM") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Add support for bulk free in Tx cleanupAlexander Duyck
This patch enables bulk Tx clean for skbs. In order to enable it we need to pass the napi_budget value as that is used to determine if we are truly running in NAPI mode or if we are simply calling the routine from netpoll with a budget of 0. In order to avoid adding too many more variables I thought it best to pass the VSI directly in a fashion similar to what we do on igb and ixgbe with the q_vector. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Fix handling of boolean logic in polling routinesAlexander Duyck
In the polling routines for i40e and i40evf we were using bitwise operators to avoid the side effects of the logical operators, specifically the fact that if the first case is true with "||" we skip the second case, or if it is false with "&&" we skip the second case. This fixes an earlier patch that converted the bitwise operators over to the logical operators and instead replaces the entire thing with just an if statement since it should be more readable what we are trying to do this way. Fixes: 1a36d7fadd14 ("i40e/i40evf: use logical operators, not bitwise") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40evf: remove dead codeAlan Cox
The only error case is when the malloc fails, in which case the clean up loop does nothing at all, so remove it Signed-off-by: Alan Cox <alan@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-04-05i40e/i40evf: Allow up to 12K bytes of data per Tx descriptor instead of 8KAlexander Duyck
From what I can tell the practical limitation on the size of the Tx data buffer is the fact that the Tx descriptor is limited to 14 bits. As such we cannot use 16K as is typically used on the other Intel drivers. However artificially limiting ourselves to 8K can be expensive as this means that we will consume up to 10 descriptors (1 context, 1 for header, and 9 for payload, non-8K aligned) in a single send. I propose that we can reduce this by increasing the maximum data for a 4K aligned block to 12K. We can reduce the descriptors used for a 32K aligned block by 1 by increasing the size like this. In addition we still have the 4K - 1 of space that is still unused. We can use this as a bit of extra padding when dealing with data that is not aligned to 4K. By aligning the descriptors after the first to 4K we can improve the efficiency of PCIe accesses as we can avoid using byte enables and can fetch full TLP transactions after the first fetch of the buffer. This helps to improve PCIe efficiency. Below is the results of testing before and after with this patch: Recv Send Send Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size Size Size Time Throughput local remote local remote bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB Before: 87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00 After: 87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00 So the net result of this patch is that we have a small gain in throughput due to a reduction in overhead for putting together the frame. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-19i40e/i40evf: Bump i40e to 1.4.25 and i40evf to 1.4.15Jesse Brandeburg
Bump. Change-ID: Ifa19aadaa892ad103f1b96fe2361fa690912c6a3 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-18i40e: implement and use Rx CTL helper functionsShannon Nelson
Use the new AdminQ functions for safely accessing the Rx control registers that may be affected by heavy small packet traffic. Change-ID: Ibb00983e8dcba71f4b760222a609a5fcaa726f18 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-18i40e: add adminq commands for Rx CTL registersShannon Nelson
Add the new opcodes and struct used for asking the firmware to update Rx control registers that need extra care when being accessed while under heavy traffic - e.g. sustained 64byte packets at line rate on all ports. The firmware will take extra steps to be sure the register accesses are successful. The registers involved are: PFQF_CTL_0 PFQF_HENA PFQF_FDALLOC PFQF_HREGION PFLAN_QALLOC VPQF_CTL VFQF_HENA VFQF_HREGION VSIQF_CTL VSILAN_QBASE VSILAN_QTABLE VSIQF_TCREGION PFQF_HKEY VFQF_HKEY PRTQF_CTL_0 GLFCOE_RCTL GLFCOE_RSOF GLQF_CTL GLQF_SWAP GLQF_HASH_MSK GLQF_HASH_INSET GLQF_HSYM GLQF_FC_MSK GLQF_FC_INSET GLQF_FD_MSK PRTQF_FD_INSET PRTQF_FD_FLXINSET PRTQF_FD_MSK Change-ID: I56c8144000da66ad99f68948d8a184b2ec2aeb3e Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-02 22:34:49 +0000