| Age | Commit message (Collapse) | Author |
|---|
|
There are two ways to get RSS, this patch implements two functions
with the same input parameters, and creates a more generic function
for getting RSS configuration.
Change-ID: I12d3b712c21455d47dd0a5aae58fc9b7c680db59
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are two ways to configure RSS, this patch adjusts those two
functions with the same input parameters, and creates a more
generic function for configuring RSS.
Change-ID: Iace73bdeba4831909979bef221011060ab327f71
Signed-off-by: Helin Zhang <helin.zhang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The adaptive ITR (interrupt throttle rate) algorithm was adjusting
the hardware's interrupt rate too frequently. This caused a lot
of variation in the interrupt rate for fairly constant workloads.
Change the code to have a counter and adjust only once every N
number of interrupts.
Change-ID: I0460f1f86571037484eca5aca36ac4d889cb8389
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On some devices, in some systems, in some configurations, the VFs would
fail to initialize the first time you loaded the driver.
To correct this, increase the delay time for the init task slightly, and
wait longer before giving up.
If we enable VFs and load the VF driver in the same kernel as the PF
driver, we can totally overwhelm the PF driver with AQ requests because
all of the instances try to initialize at the same time.
To help alleviate this, stagger the initial scheduling of the init task
using the PCIe function as a multiplier. We mask off the function to
only three bits so no instance has to wait too long.
With these two changes, initializing 128 VFs on a single device goes
from four minutes to just a few seconds.
Change-ID: If3d8720c1c4e838ab36d8781d9ec295a62380936
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code in i40e and i40evf is using an "IN_NETPOLL" flag that has never
added any value due to the fact that the Rx clean-up is handled in NAPI.
As such the flag was set, the queue was scheduled via NAPI, and then polled
from the netpoll controller and if any Rx packets were processed the were
processed in the wrong context.
In addition the flag itself just added an unneeded conditional to the
hot-path so it can safely be dropped and save us a few instructions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was not correctly handling calls to its ndo_set_mac_address
method. It did not properly check to see if the override would be
allowed by the PF driver, and never removed the old address from its
filter list.
Add a new flag to the adapter struct which is set if the MAC address is
assigned by the PF. Check this flag and don't allow the MAC address to
be changed if it is set. Search for and properly remove the filter
for the old MAC address when the new one is set.
Change-ID: I817bf620c869c5a80e6a7eab65c9cbad1dc89799
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The VF really doesn't care about the QOS handle but it will in the
future. Since the VF only uses TC0, send it that handle. On the VF
side, save the handle and use it to populate the QOS params when we call
into the client interface.
Change-ID: I76f41b070baeaa09b19383e9168bc677837e0761
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add missings spaces after declarations, remove another __func__ use,
remove uncessary braces, remove unneeded breaks, and useless returns,
and generally fix up some code.
Change-ID: Ie715d6b64976c50e1c21531685fe0a2bd38c4244
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X722 fixes an issue from X710 where TX descriptor WB would not happen if
the interrupts were disabled. In order for the write backs to happen a
bit needs to be set in the dynamic interrupt control register called
WB_ON_ITR. With this feature, the SW driver need not arm SW interrupts to
work around the issue in X710.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
X722 uses the admin queue to configure RSS. This patch adds the necessary
flow changes to configure RSS through AQ. It also adds the separate VMDQ2
lookup tables and hash key programming for X722.
X722 also exposes a different set of PCTYPES for RSS, this patch
accommodates those changes.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add capabilities flags specific to X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use macros for abstracting (1 << foo) to BIT(foo)
and (1ULL << foo64) to BIT_ULL(foo64) in order to match
better with kernel requirements.
NOTE: the adminq_cmd.h file was not modified on purpose because
of the dependency upon firmware for that file.
Change-ID: I73ee2e48c880d671948aad19bd53ca6b2ac558fc
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The most common type of reset that the VF will encounter is a PF reset
that cascades down into a VF reset for each VF. In this case, the VF
will always be assigned the same VSI and recovery is fairly simple.
However, in the case of 'bigger' resets, such as a Core or EMP reset,
when the device is reinitialized, it's probable that the VF will NOT get
the same VSI. When this happens, the VF will not be able to recover, as
it will continue to request resources for its original VSI.
Add an extra state to the admin queue state machine so that the driver
can re-request its configuration information at runtime. During reset
recovery, set this bit in the aq_required field, and fetch the (possibly
new) configuration information before attempting to bring the driver
back up. Since the driver doesn't know what kind of reset it has
encountered, this step is done even for a PF reset, but it doesn't hurt
anything - it just gets the same VSI back.
Change-ID: I915d59ffb40375215117362f4ac7a37811aba748
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that we've rolled the virtual channel API version to 1.1, add some
macros to test what version is being used by our partner in crime. For the
VF, add some macros to determine what our device capabilities are.
Change-ID: I79f6683d4c23bd76a8ad9fd492776fcc1208e1dc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable. This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.
Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.
Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The aq_pending field in the adapter structure is actually redundant with
the current_op field. Remove the aq_pending field and expunge all traces
of it from the official record. This simplifies the code significantly,
especially in the virtual channel completion routine.
Change-ID: Ib2957c8c19882bd0cecc6fcd133912c24b46a1ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the VF interface is closed, we cannot immediately free our rings
and RX buffers, because the hardware hasn't yet stopped accessing this
memory. This shows up as a panic or memory corruption when the device is
brought down while under heavy stress.
To fix this, delay releasing resources until we receive acknowledgment
from the PF driver that the rings have indeed been stopped. Because of
this delay, we also need to check to make sure that all of our admin
queue requests have been handled before allowing the device to be
opened.
Change-ID: I44edd35529ce2fa2a9512437a3a8e6f14ed8ed63
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is the result of running checkpatch on the i40evf driver with
the --strict option. The vast majority of changes are adding/removing
blank lines, aligning function parameters, and correcting over-long
lines.
The only possible functional change is changing the flags member of the
adapter structure to be non-volatile. However, according to the kernel
documentation, this is not necessary and the volatile should be removed.
Change-ID: Ie8c6414800924f529bef831e8845292b970fe2ed
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It's kind of silly to configure and attempt to use a bunch of queue
pairs when you're running on a single (virtual) CPU. Instead of
unconditionally configuring all of the queues that the PF gives us,
clamp the number of queue pairs to the number of CPUs.
Change-ID: I321714c9e15072ee76de8f95ab9a81f86ed347d1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Patrick Lu <patrick.lu@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Hardware requires descriptors to be allocated in groups of 32.
Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Adding the appropriate GNU General Public License header and
update copyright year to 2014.
Change-ID: I769dd2d37d70350afd0c8727ae2859c0fd340361
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The Tx watchdog handler runs in interrupt context, so it would cause an
oops when sending an admin queue message to request a reset, because the
admin queue functions use spinlocks.
Instead, set a flag and let the reset task handle sending the request.
Change-ID: I65879470b72963d9c308edfb8f45ac4fbba2c14f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Keep the descriptor ring size in the actual ring structs instead of in
the adapter struct. This enables us to use common tx and rx code with
the i40e PF driver.
Also update copyrights.
Change-ID: I2861e599b2b4c76441c062ea14400f4750f54d0e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the kernel watchdog bites us, ask the PF to reset us and attempt to
reinit the driver.
Change-ID: Ic97665aeeed71ce712b9c4f057e78ff8372522b9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
linux/sctp.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As pointed out by Dan Carpenter (from Oracle), the flags variable is
declared as a 64-bit long but all of the flags are defined as u32,
which may lead to unintended consequences. Fix this by declaring flags
as u32 (since we don't need any more than about a dozen flags right
now), and remove the volatile qualifier, since it's unnecessary and
just makes checkpatch cry.
Change-ID: I137d3bb1842bf7e9456b5929ca54e3b0ed45dcab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Locate the structure in the correct header file.
Change-ID: Ic7853131728812093a44a75d6b70953311a48dab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a bunch of unused structure members that are just wasting
space. Remove a completely unused info structure definition as well.
Also update copyrights.
Change-ID: I028ab92d9b7bd13a832cf3363bd1dc6610d8a535
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch contains the main driver header files, containing structures
and data types specific to the linux driver.
i40e_osdep.h contains some code that helps us adapt our OS agnostic code
to Linux.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
