| Age | Commit message (Collapse) | Author |
|---|
|
Could a Bad Person do Bad Things to a server if they found these
addresses printed in the log? Who knows? But let's not take that risk.
Remove pointers from a bunch of printks. In some cases, I was able to
adjust the message to indicate whether or not the value was null. In
others, I just removed the entire message as there was really no hope of
saving it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:5440:5: warning:
symbol 'i40e_get_link_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch replaces the existing mechanism for determining the correct
value to program for adaptive ITR with yet another new and more
complicated approach.
The basic idea from a 30K foot view is that this new approach will push the
Rx interrupt moderation up so that by default it starts in low latency and
is gradually pushed up into a higher latency setup as long as doing so
increases the number of packets processed, if the number of packets drops
to 4 to 1 per packet we will reset and just base our ITR on the size of the
packets being received. For Tx we leave it floating at a high interrupt
delay and do not pull it down unless we start processing more than 112
packets per interrupt. If we start exceeding that we will cut our interrupt
rates in half until we are back below 112.
The side effect of these patches are that we will be processing more
packets per interrupt. This is both a good and a bad thing as it means we
will not be blocking processing in the case of things like pktgen and XDP,
but we will also be consuming a bit more CPU in the cases of things such as
network throughput tests using netperf.
One delta from this versus the ixgbe version of the changes is that I have
made the interrupt moderation a bit more aggressive when we are in bulk
mode by moving our "goldilocks zone" up from 48 to 96 to 56 to 112. The
main motivation behind moving this is to address the fact that we need to
update less frequently, and have more fine grained control due to the
separate Tx and Rx ITR times.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is mostly prep-work for replacing the current approach to
programming the dynamic aka adaptive ITR. Specifically here what we are
doing is splitting the Tx and Rx ITR each into two separate values.
The first value current_itr represents the current value of the register.
The second value target_itr represents the desired value of the register.
The general plan by doing this is to allow for deferring the update of the
ITR value under certain circumstances. For now we will work with what we
have, but in the future I hope to change the behavior so that we always
only update one ITR at a time using some simple logic to determine which
ITR requires an update.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.
This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.
Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag. This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads. This means
we need some way to detect if FW LLDP is enabled on init. We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.
This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it. If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.
The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.
This patch also adds a comment explaining that the cmpxchg is the point
of no return. Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.
This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.
The other big change made here is that we replace references to:
vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
q_vector->rx.ring->itr_setting
The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
'bufer' should be 'buffer'
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch suppresses the message about invalid TC mapping and wrong
selected TX queue. The root cause of this bug was setting too many
TC queue pairs on huge multiprocessor machines. When quantity of the
TC queue pairs is exceeding MSI-X vectors count then TX queue number
can be selected beyond actual TX queues amount.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The drivers for i40e and i40evf had a reg_idx value stored in the q_vector
that was going completely unused. I can only assume this was copied over
from ixgbe and nobody knew how to use it.
I'm going to make use of the value to avoid having to compute the vector
and thus the register index for multiple paths throughout the drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 36777d9fa24c ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa24c ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Our hardware does not allow situations where two filters might conflict
when matching. Essentially hardware only programs one filter for each
set of matching criteria. We don't support filters with overlapping
input sets, because each flow type can only use a single input set.
Additionally, different flow types will never have overlapping matches,
because of how the hardware parses the flow type before checking
matching criteria.
For this reason, we do not need or use the location number when
programming filters to hardware.
In order to avoid confusing scenarios with filters that match the same
criteria but program the flow to different queues, do not allow multiple
filters that match identical criteria to be programmed.
This ensures that we avoid odd scenarios when deleting filters, and when
programming new filters that match the same criteria.
Instead, users that wish to update the criteria for a filter must use
the same location id, or must delete all the matching filters first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
kdump fails in the system when used in conjunction with Ethernet driver
X722/X710. This is mainly because when we are resource constrained i.e.
when we have just one online_cpus, we are enabling VMDq and iWARP. It
doesn't make sense to enable them with just one CPU and starve kdump
for lack of IRQs.
So don't enable VMDq or iWARP when we just have a single CPU.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clean up unnecessary parenthesis.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
|
|
Using ethtool --set-priv-flags disable-fw-lldp <on/off> is persistent
across reboots/reloads so we need some mechanism in the driver to detect
if it's on or off on init so we can set the ethtool private flag
appropriately. Without this, every time the driver is reloaded the flag
will default to off regardless of whether it's on or off in FW.
We detect this by first attempting to program DCB and if AQ fails
returning I40E_AQ_RC_EPERM, we know that LLDP is disabled in FW.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As we have added more flags, we need to now use more
bits and have over flooded the 32 bit size. So
make it 64.
Also change all the existing bits to unsigned long long
bits.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch enables driver to display LLDP information on the vSphere Web
Client with Intel adapters (X710, XL710) and Distributed Virtual Switch.
Signed-off-by: Upasana Menon <upasana.menon@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The FW has the ability to return a critical error on every AQ command.
When this critical error occurs then we need to send the correct response
to the caller.
Signed-off-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Make use of tc_cls_can_offload_and_chain0() to set extack msg in case
ethtool tc offload flag is not set or chain unsupported.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a768b7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40e_init_interrupt_scheme()
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Client close is overloaded to handle both un-registration and
netdev down event. On netdev down, i40iw client close is called
which unregisters the RDMA dev and this is too destructive
since the netdev is still registered.
Do not call client close/open on netdev down/up events. Instead
disable the PE TCP_ENA flag during a netdev down event. This
blocks all TCP traffic to the RDMA Protocol Engine. On netdev up,
re-enable the flag.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fix solves an issue occurring while calling i40e_led_set function
from the driver with "blink" parameter set as TRUE. This call resulted
in Activity LED blinking instead of Link LED, which may lead to errors
in physically identifying the port, since Activity LED may be blinking
for different reasons as well.
Signed-off-by: Michal Kuchta <michal.kuchta@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
for NVM update
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
track_id == 0 is valid for “read only” profiles when
profile does not have any “write” commands.
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Variable read_size is initialized and this value is never read, it is
instead set inside the do-loop, hence the initialization is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:390:6: warning: Value stored
to 'read_size' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We introduced the virtchnl interface in order to have an interface for
talking to a virtual device driver which was host-driver agnostic. This
interface has its own definitions, including one for link speed.
The host driver has to talk to the virtchnl interface using these new
definitions in order to remain compatible. Today, the i40e link_speed
enumerations are value-exact matches for the virtchnl interface, so it
was originally decided to simply use a typecast.
However, this is unsafe, and makes it easier for future drivers to
continue this unsafe practice. There is nothing guaranteeing these
values are exact, and the type-cast would hide any compiler warning
which indicates the problem.
Rather than rely on this type cast, introduce a helper function which
can convert the AdminQ link speed definition into a virtchnl
definition. This can then be used by host driver implementations in
order to safely convert to the interface recognized by the virtual
functions.
If the link speed is not able to be represented by the virtchnl
definitions we'll report UNKNOWN which is the safest result.
This will ensure that should the driver specific link_speeds actual bit
definitions change, we do not report them incorrectly according to the
VF.
Additionally, this provides a better pattern for future drivers to copy,
as it is more likely a future device may not use the exact same bit-wise
definition as the current virtchnl interface.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We currently notify a VF of the link state after ENABLE_QUEUES, which is
the last thing a VF does after being configured. Guests may not actually
ENABLE_QUEUES until they get configured, and thus between driver load
and device configuration the VF may show inaccurate link status.
Fix this by also sending the link state after GET_VF_RESOURCES. Although
we could remove the message following ENABLE_QUEUES, it's not that
significant of a loss, so this patch just keeps both to ensure maximum
compatibility with guests on various OSes.
Specifically, without this patch guests running FreeBSD will display
inaccurate link state until the device is brought up. This is mostly
a cosmetic issue but can be confusing to system administrators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Display some more stats that were already being counted, to help users
understand when priority xon/xoff packets are being sent/received
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
|
The i40e driver has a special "FDIR" RX-ring (I40E_VSI_FDIR) which is
a sideband channel for configuring/updating the flow director tables.
This (i40e_vsi_)type does not invoke XDP-ebpf code.
As suggested by Björn (V2): Instead of marking this I40E_VSI_FDIR RX-ring
a special case, reverse the logic and only select RX-rings of type
I40E_VSI_MAIN to register xdp_rxq_info's for.
Driver hook points for xdp_rxq_info:
* reg : i40e_setup_rx_descriptors (via i40e_vsi_setup_rx_resources)
* unreg: i40e_free_rx_resources (via i40e_vsi_free_rx_resources)
Tested on actual hardware with samples/bpf program.
V2: Fixed bug in i40e_set_ringparam (memset zero) + match on I40E_VSI_MAIN.
V4: Update patch desc that got out-of-sync with code.
Cc: intel-wired-lan@lists.osuosl.org
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
