| Age | Commit message (Collapse) | Author |
|---|
|
Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag. This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads. This means
we need some way to detect if FW LLDP is enabled on init. We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.
This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it. If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.
The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.
This patch also adds a comment explaining that the cmpxchg is the point
of no return. Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 36777d9fa24c ("i40e: check current configured input set when
adding ntuple filters") some code was added to report the input set
mask for a given filter when reporting it to the user.
This code is necessary so that the reported filter correctly displays
that it is or is not masking certain fields.
Unfortunately the code was incorrect. Development error accidentally
swapped the mask values for the IPv4 addresses with the L4 port numbers.
The port numbers are only 16bits wide while IPv4 addresses are 32 bits.
Unfortunately we assigned only 16 bits to the IPv4 address masks.
Additionally we assigned 32bit value 0xFFFFFFF to the TCP port numbers.
This second part does not matter as the value would be truncated to
16bits regardless, but it is unnecessary.
Fix the reported masks to properly report that the entire field is
masked.
Fixes: 36777d9fa24c ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Our hardware does not allow situations where two filters might conflict
when matching. Essentially hardware only programs one filter for each
set of matching criteria. We don't support filters with overlapping
input sets, because each flow type can only use a single input set.
Additionally, different flow types will never have overlapping matches,
because of how the hardware parses the flow type before checking
matching criteria.
For this reason, we do not need or use the location number when
programming filters to hardware.
In order to avoid confusing scenarios with filters that match the same
criteria but program the flow to different queues, do not allow multiple
filters that match identical criteria to be programmed.
This ensures that we avoid odd scenarios when deleting filters, and when
programming new filters that match the same criteria.
Instead, users that wish to update the criteria for a filter must use
the same location id, or must delete all the matching filters first.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When implementing support for IP_USER_FLOW filters, we correctly
programmed a filter for both the non fragmented IPv4/Other filter, as
well as the fragmented IPv4 filters. However, we did not properly
program the input set for fragmented IPv4 PCTYPE. This meant that the
filters would almost certainly not match, unless the user specified all
of the flow types.
Add support to program the fragmented IPv4 filter input set. Since we
always program these filters together, we'll assume that the two input
sets must match, and will thus always program the input sets to the same
value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement the private flag disable-fw-lldp for ethtool
to disable the processing of LLDP packets by the FW.
This will stop the FW from consuming LLDPDU and cause
them to be sent up the stack.
The FW is also being configured to apply a default DCB
configuration on link up.
Toggling the value of this flag will also cause a PF reset.
Disabling FW DCB will also disable DCBx.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As we have added more flags, we need to now use more
bits and have over flooded the 32 bit size. So
make it 64.
Also change all the existing bits to unsigned long long
bits.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change cleans up the i40e/i40evf_set_itr_per_queue function by
dropping all the unneeded pointer chases. Instead we can just pull out the
pointers for the Tx and Rx rings and use them throughout the function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch reorders i40e_add_del_fdir and i40e_update_ethtool_fdir_entry
calls so that we first remove an already existing filter (inside
i40e_update_ethtool_fdir_entry using i40e_add_del_fdir) and then
we add a new one with i40e_add_del_fdir.
After applying this patch, creating multiple identical filters (with
the same location) one after another doesn't revert their behavior
but behaves correctly.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Display some more stats that were already being counted, to help users
understand when priority xon/xoff packets are being sent/received
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e driver has a special "FDIR" RX-ring (I40E_VSI_FDIR) which is
a sideband channel for configuring/updating the flow director tables.
This (i40e_vsi_)type does not invoke XDP-ebpf code.
As suggested by Björn (V2): Instead of marking this I40E_VSI_FDIR RX-ring
a special case, reverse the logic and only select RX-rings of type
I40E_VSI_MAIN to register xdp_rxq_info's for.
Driver hook points for xdp_rxq_info:
* reg : i40e_setup_rx_descriptors (via i40e_vsi_setup_rx_resources)
* unreg: i40e_free_rx_resources (via i40e_vsi_free_rx_resources)
Tested on actual hardware with samples/bpf program.
V2: Fixed bug in i40e_set_ringparam (memset zero) + match on I40E_VSI_MAIN.
V4: Update patch desc that got out-of-sync with code.
Cc: intel-wired-lan@lists.osuosl.org
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
|
|
Add definitions for L4 filters and switch modes based on cloud filters
modes and extend the set switch config command to include the
additional cloud filter mode.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
to READ_ONCE()/WRITE_ONCE()
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This finishes off the conversion to the new ethtool API by removing the
old macros being used in i40e_set_link_ksettings and replacing them with
shiny new ones.
This conversion also allows us to provide link speed support for new 25G
and 10G macros which is included here as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This variable isn't actually very descriptive and makes the code a bit
confusing as to what it is being used for. This patch enhances the
variable with the longer name, 'autoneg_changed', which makes it clear
we are concerned with autoneg changing in this context.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This removes references to old ethtool API macros and functions in
i40e_get_settings_link_up as part of the process of converting to the
new API. The new API also allows us to provide more explicit support
for new 25G and 10G PHY types so some of the PHY types have been
adjusted where necessary as well.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We are still largely using the old ethtool API macros. This is
problematic because eventually they will be removed and they only
support 32 bits of PHY types.
This overhauls i40e_phy_type_to_ethtool to use only the new API. Doing
this also allows us to provide much better support for newer 25G and 10G
PHY types which is included here as well.
The remaining usages of the old ethtool API will be addressed in other
patches in the series.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Krzysztof Malek <krzysztof.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This separates the setting of autoneg in i40e_phy_types_to_ethtool into
its own conditional. Doing this adds clarity as what PHYs
support/advertise autoneg and makes it easier to add new PHY types in
the future.
This also fixes an issue on devices with CRT_RETIMER where advertising
autoneg was being set, but supported autoneg was not.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There's a number of minor incidental whitespace issues in this file.
This addresses most of the ones I could find.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Someone forgot a word in this comment and it's confusing without it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The function header erroneously listed 'phy_types' as a parameter. The
correct parameter is 'pf'.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This fixes two issues in i40e_get_link_ksettings. It adds calls to
ethtool_link_ksettings_zero_link_mode to make sure advertising and
supported link masks are cleared before we start setting bits in them.
This also replaces some funky bit manipulations with a much nicer call
to ethtool_link_ksettings_del_link_mode when removing link modes.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Someone left this poor little function naked with no header. This
dresses it up in a proper function header it deserves.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This 'ifdef' doesn't accomplish anything so remove it.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After the switch to the new ethtool API, ethtool passes us
ethtool_ksettings structs instead of ethtool_command structs, however we
were still referring to them as 'cmd' variables. This renames them to
'ks' variables which makes the code easier to understand.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that we've reduced the number of flags, organize similar flags
together and re-number them accordingly.
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
One alternative approach considered, but not implemented here, was to
use an enumeration for the flag variables, and create a macro
I40E_FLAG() which used string concatenation to generate BIT_ULL values.
This has the advantage of making the actual bit values compile-time
dynamic so that we do not need to worry about matching the order to the
bit value. However, this does produce a high level of code churn, and
makes it more difficult to read a dumped flags value when debugging.
Change-ID: I8653fff69453cd547d6fe98d29dfa9d8710387d1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previous implementation of LED set/get functions required to enter
PHY debug mode, in order to prevent access to it from FW and SW at
the same time. Reset of all ports was a unwanted side effect.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
By default, our devices do source pruning, that is, they drop receive
packets that have the source MAC matching one of the receive filters.
Unfortunately, this breaks ARP monitoring in channel bonding, as the
bonding driver expects devices to receive ARPs containing their own
source address.
Add an ethtool private flag to control this feature.
Also, remove the netif_running() check when we process our private
flags. It's OK to reset when the device is closed and in most cases we
need the reset the apply these changes.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the driver allows the user to change (or even disable)
interrupt moderation if adaptive-rx/tx is enabled when this should
not be the case.
Adaptive RX/TX will not respect the user's ITR settings so
allowing the user to change it is weird. This bug would also
allow the user to disable interrupt moderation with adaptive-rx/tx
enabled which doesn't make much sense either.
This patch makes it such that if adaptive-rx/tx is enabled, the user
cannot make any manual adjustments to interrupt moderation. It also
makes it so that if ITR is disabled but adaptive-rx/tx is then
enabled, ITR will be re-enabled.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a user gives an invalid command to change a private flag which is
not supported, either because it is read-only, or the device is not
capable of the feature, we simply ignore the request.
A naive solution would simply be to report error codes when one of the
flags was not supported. However, this causes problems because it makes
the operation not atomic. If a user requests multiple private flags
together at once we could end up changing one before failing at the
second flag.
We can do a bit better if we instead update a temporary copy of the
flags variable in the loop, and then copy it into place after. If we
aren't careful this has the pitfall of potentially silently overwriting
any changes caused by other threads.
Avoid this by using cmpxchg64 which will compare and swap the flags
variable only if it currently matched the old value. We'll report
-EAGAIN in the (hopefully rare!) case where the cmpxchg64 fails.
This ensures that we can properly report when flags are not supported in
an atomic fashion without the risk of overwriting other threads changes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.
Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.
Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.
The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.
Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Compiler reported several places where driver compared
signed and unsigned types. Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a check and message if the device is in
MFP mode as changing RSS input set is not supported in
MFP mode.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The conflicts were two cases of overlapping changes in
batman-adv and the qed driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a36 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The i40e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The check for I40E_CONFIG_BUSY state bit in the i40e_set_link_ksettings
function is fishy. First we can notice a few things about the check here.
First a similar check was introduced by commit
'c7d05ca89f8e ("i40e: driver ethtool core")'
Later a commit introducing the link settings was added by commit
'bf9c71417f72 ("i40e: Implement set_settings for ethtool")'
However, this second check was against vsi->state instead of pf->state,
and also failed to set the bit, it only checks. That indicates the locking
was not quite correct. The only other place that the state bit
in vsi->state gets used is to protect the filter list.
Since this code does not care about the mac filter list, and seems
clear the original code should have set the pf->state bit. Fix these
issues by using pf->state correctly, and by actually setting the bit
so that we properly lock as expected.
Since these checks occur while holding the rtnl_lock(), lets also add a
timeout so that we don't potentially softlock the system.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode. The legacy Rx mode is what we currently do when performing
Rx. As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.
Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.
What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.
Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
