| Age | Commit message (Collapse) | Author |
|---|
|
The value of an arithmetic expression is subject
of possible overflow due to a failure to cast operands to a larger data
type before performing arithmetic. Used macro for multiplication instead
operator for avoiding overflow.
Found by Security Code and Linux Verification
Center (linuxtesting.org) with SVACE.
Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230309174347.3515-1-korotkov.maxim.s@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using a PHC in shared between multiple hosts, the previous
frequency value may not be reset and could lead to host being unable to
compensate the offset with timecounter adjustments. To avoid such state
reset the hardware frequency of PHC to zero on init. Some refactoring is
needed to make code readable.
Fixes: 85036aee1938 ("bnxt_en: Add a non-real time mode to access NIC clock")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Documentation/bpf/bpf_devel_QA.rst
b7abcd9c656b ("bpf, doc: Link to submitting-patches.rst for general patch submission info")
d56b0c461d19 ("bpf, docs: Fix link to netdev-FAQ target")
https://lore.kernel.org/all/20230307095812.236eb1be@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
cd709aa90648 ("bnx2: Add PCI Advanced Error Reporting support.") added
pci_enable_pcie_error_reporting() for all devices, and c239f279e571 ("bnx2:
Enable AER on PCIE devices only") restricted it to BNX2_CHIP_5709 devices
to avoid an error message when it failed on non-PCIe devices. The PCI core
only enables PCIe error reporting on PCIe devices, which I assume means
BNX2_CHIP_5709.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following warning reported by KASAN during driver unload
==================================================================
BUG: KASAN: double-free in bnxt_remove_one+0x103/0x200 [bnxt_en]
Free of addr ffff88814e8dd4c0 by task rmmod/17469
CPU: 47 PID: 17469 Comm: rmmod Kdump: loaded Tainted: G S 6.2.0-rc7+ #2
Hardware name: Dell Inc. PowerEdge R740/01YM03, BIOS 2.3.10 08/15/2019
Call Trace:
<TASK>
dump_stack_lvl+0x33/0x46
print_report+0x17b/0x4b3
? __call_rcu_common.constprop.79+0x27e/0x8c0
? __pfx_free_object_rcu+0x10/0x10
? __virt_addr_valid+0xe3/0x160
? bnxt_remove_one+0x103/0x200 [bnxt_en]
kasan_report_invalid_free+0x64/0xd0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kasan_slab_free+0x179/0x1c0
? bnxt_remove_one+0x103/0x200 [bnxt_en]
__kmem_cache_free+0x194/0x350
bnxt_remove_one+0x103/0x200 [bnxt_en]
pci_device_remove+0x62/0x110
device_release_driver_internal+0xf6/0x1c0
driver_detach+0x76/0xe0
bus_remove_driver+0x89/0x160
pci_unregister_driver+0x26/0x110
? strncpy_from_user+0x188/0x1c0
bnxt_exit+0xc/0x24 [bnxt_en]
__x64_sys_delete_module+0x21f/0x390
? __pfx___x64_sys_delete_module+0x10/0x10
? __pfx_mem_cgroup_handle_over_high+0x10/0x10
? _raw_spin_lock+0x87/0xe0
? __pfx__raw_spin_lock+0x10/0x10
? __audit_syscall_entry+0x185/0x210
? ktime_get_coarse_real_ts64+0x51/0x80
? syscall_trace_enter.isra.18+0x126/0x1a0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7effcb6fd71b
Code: 73 01 c3 48 8b 0d 6d 17 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 3d 17 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffeada270b8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 00005623660e0750 RCX: 00007effcb6fd71b
RDX: 000000000000000a RSI: 0000000000000800 RDI: 00005623660e07b8
RBP: 0000000000000000 R08: 00007ffeada26031 R09: 0000000000000000
R10: 00007effcb771280 R11: 0000000000000206 R12: 00007ffeada272e0
R13: 00007ffeada28bc4 R14: 00005623660e02a0 R15: 00005623660e0750
</TASK>
Auxiliary device structures are freed in bnxt_aux_dev_release. So avoid
calling kfree from bnxt_remove_one.
Also, set bp->edev to NULL before freeing the auxilary private structure.
Fixes: d80d88b0dfff ("bnxt_en: Add auxiliary driver support")
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to keep track of all the possible concurrent TPA (GRO/LRO)
completions on the aggregation ring. On P5 chips, the maximum number
of concurrent TPA is 256 and the amount of memory we allocate is order-5
on systems using 4K pages. Memory allocation failure has been reported:
NetworkManager: page allocation failure: order:5, mode:0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null),cpuset=/,mems_allowed=0-1
CPU: 15 PID: 2995 Comm: NetworkManager Kdump: loaded Not tainted 5.10.156 #1
Hardware name: Dell Inc. PowerEdge R660/0M1CC5, BIOS 0.2.25 08/12/2022
Call Trace:
dump_stack+0x57/0x6e
warn_alloc.cold.120+0x7b/0xdd
? _cond_resched+0x15/0x30
? __alloc_pages_direct_compact+0x15f/0x170
__alloc_pages_slowpath.constprop.108+0xc58/0xc70
__alloc_pages_nodemask+0x2d0/0x300
kmalloc_order+0x24/0xe0
kmalloc_order_trace+0x19/0x80
bnxt_alloc_mem+0x1150/0x15c0 [bnxt_en]
? bnxt_get_func_stat_ctxs+0x13/0x60 [bnxt_en]
__bnxt_open_nic+0x12e/0x780 [bnxt_en]
bnxt_open+0x10b/0x240 [bnxt_en]
__dev_open+0xe9/0x180
__dev_change_flags+0x1af/0x220
dev_change_flags+0x21/0x60
do_setlink+0x35c/0x1100
Instead of allocating this big chunk of memory and dividing it up for the
concurrent TPA instances, allocate each small chunk separately for each
TPA instance. This will reduce it to order-0 allocations.
Fixes: 79632e9ba386 ("bnxt_en: Expand bnxt_tpa_info struct to support 57500 chips.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While bringing hardware up we should perform a full reset including the
switch bit (BGMAC_BCMA_IOCTL_SW_RESET aka SICF_SWRST). It's what
specification says and what reference driver does.
This seems to be critical for the BCM5358. Without this hardware doesn't
get initialized properly and doesn't seem to transmit or receive any
packets.
Originally bgmac was calling bgmac_chip_reset() before setting
"has_robosw" property which resulted in expected behaviour. That has
changed as a side effect of adding platform device support which
regressed BCM5358 support.
Fixes: f6a95a24957a ("net: ethernet: bgmac: Add platform device support")
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230227091156.19509-1-zajec5@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Per-next-PR merge.
net/smc/af_smc.c
b5dd4d698171 ("net/smc: llc_conf_mutex refactor, replace it with rw_semaphore")
e40b801b3603 ("net/smc: fix potential panic dues to unprotected smc_llc_srv_add_link()")
https://lore.kernel.org/all/20230221124008.6303c330@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When we suspend into s2idle we also need to enable the interrupt line
that generates the MPD and HFB interrupts towards the host CPU interrupt
controller (typically the ARM GIC or MIPS L1) to make it exit s2idle.
When we suspend into other modes such as "standby" or "mem" we engage a
power management state machine which will gate off the CPU L1 controller
(priv->irq0) and ungate the side band wake-up interrupt (priv->wol_irq).
It is safe to have both enabled as wake-up sources because they are
mutually exclusive given any suspend mode.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bcmgenet_mii_config() code was refactored it was missed
that the LED control for the MoCA interface got overwritten by
the port_ctrl value. Its previous programming is restored here.
Fixes: 4f8d81b77e66 ("net: bcmgenet: Refactor register access in bcmgenet_mii_config")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the devlink bits were tricky, but I think I got it right.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.")
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d01 ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad236 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Code blocks handling BCMA_CHIP_ID_BCM5357 and BCMA_CHIP_ID_BCM53572 were
incorrectly unified. Chip package values are not unique and cannot be
checked independently. They are meaningful only in a context of a given
chip.
Packages BCM5358 and BCM47188 share the same value but then belong to
different chips. Code unification resulted in treating BCM5358 as
BCM47188 and broke its initialization.
Link: https://github.com/openwrt/openwrt/issues/8278
Fixes: cb1b0f90acfe ("net: ethernet: bgmac: unify code of the same family")
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230208091637.16291-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ajit Khaparde says:
====================
bnxt: Add Auxiliary driver support
Add auxiliary device driver for Broadcom devices.
The bnxt_en driver will register and initialize an aux device
if RDMA is enabled in the underlying device.
The bnxt_re driver will then probe and initialize the
RoCE interfaces with the infiniband stack.
We got rid of the bnxt_en_ops which the bnxt_re driver used to
communicate with bnxt_en.
Similarly We have tried to clean up most of the bnxt_ulp_ops.
In most of the cases we used the functions and entry points provided
by the auxiliary bus driver framework.
And now these are the minimal functions needed to support the functionality.
We will try to work on getting rid of the remaining if we find any
other viable option in future.
* 'aux-bus-v11' of https://github.com/ajitkhaparde1/linux:
bnxt_en: Remove runtime interrupt vector allocation
RDMA/bnxt_re: Remove the sriov config callback
bnxt_en: Remove struct bnxt access from RoCE driver
bnxt_en: Use auxiliary bus calls over proprietary calls
bnxt_en: Use direct API instead of indirection
bnxt_en: Remove usage of ulp_id
RDMA/bnxt_re: Use auxiliary driver interface
bnxt_en: Add auxiliary driver support
====================
Link: https://lore.kernel.org/r/20230202033809.3989-1-ajit.khaparde@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Modified the bnxt_en code to create and pre-configure RDMA devices
with the right MSI-X vector count for the ROCE driver to use.
This is to align the ROCE driver to the auxiliary device model which
will simply bind the driver without getting into PCI-related handling.
All PCI-related logic will now be in the bnxt_en driver.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Remove the SRIOV config callback which the bnxt_en was calling
to reconfigure the chip resources for a PF device when VFs are
created. The code is now modified to provision the VF resources
based on the total VF count instead of the actual VF count.
This allows the SRIOV config callback to be removed from the
list of ulp_ops.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Decouple RoCE driver from directly accessing L2's private bnxt
structure. Move the fields needed by RoCE driver into bnxt_en_dev.
They'll be passed to RoCE driver by bnxt_rdma_aux_device_add()
function.
Signed-off-by: Hongguang Gao <hongguang.gao@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Wherever possible use the function ops provided by auxiliary bus
instead of using proprietary ops.
Defined bnxt_re_suspend and bnxt_re_resume calls which can be
invoked by the bnxt_en driver instead of the ULP stop/start calls.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
For a single ULP user there is no need for complicating function
indirection calls. Remove all this complexity in favour of direct
function calls exported by the bnxt_en driver. This allows to
simplify the code greatly. Also remove unused ulp_async_notifier.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Since the driver continues to use the single ULP model,
the extra complexity and indirection is unnecessary.
Remove the usage of ulp_id from the code.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Use auxiliary driver interface for driver load, unload ROCE driver.
The driver does not need to register the interface using the netdev
notifier anymore. Removed the bnxt_re_dev_list which is not needed.
Currently probe, remove and shutdown ops have been implemented for
the auxiliary device.
Also remove exccessve validation checks for rdev.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Add auxiliary driver support.
An auxiliary device will be created if the hardware indicates
support for RDMA.
The bnxt_ulp_probe() function has been removed and a new
bnxt_rdma_aux_device_add() function has been added.
The bnxt_free_msix_vecs() and bnxt_req_msix_vecs() will now hold
the RTNL lock when they call the bnxt_close_nic()and bnxt_open_nic()
since the device close and open need to be protected under RTNL lock.
The operations between the bnxt_en and bnxt_re will be protected
using the en_ops_lock.
This will be used by the bnxt_re driver in a follow-on patch
to create ROCE interfaces.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The function __b44_cam_read() is defined in the b44.c file, but not called
elsewhere, so remove this unused function.
drivers/net/ethernet/broadcom/b44.c:199:20: warning: unused function '__b44_cam_read'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3858
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230128090413.79824-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Devlink features were introduced to disallow devlink reload calls of
userspace before the devlink was fully initialized. The reason for this
workaround was the fact that devlink reload was originally called
without devlink instance lock held.
However, with recent changes that converted devlink reload to be
performed under devlink instance lock, this is redundant so remove
devlink features entirely.
Note that mlx5 used this to enable devlink reload conditionally only
when device didn't act as multi port slave. Move the multi port check
into mlx5_devlink_reload_down() callback alongside with the other
checks preventing the device from reload in certain states.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Occasionnaly we may get oversized packets from the hardware which
exceed the nomimal 2KiB buffer size we allocate SKBs with. Add an early
check which drops the packet to avoid invoking skb_over_panic() and move
on to processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During EEH error injection testing, a deadlock was encountered in the tg3
driver when tg3_io_error_detected() was attempting to cancel outstanding
reset tasks:
crash> foreach UN bt
...
PID: 159 TASK: c0000000067c6000 CPU: 8 COMMAND: "eehd"
...
#5 [c00000000681f990] __cancel_work_timer at c00000000019fd18
#6 [c00000000681fa30] tg3_io_error_detected at c00800000295f098 [tg3]
#7 [c00000000681faf0] eeh_report_error at c00000000004e25c
...
PID: 290 TASK: c000000036e5f800 CPU: 6 COMMAND: "kworker/6:1"
...
#4 [c00000003721fbc0] rtnl_lock at c000000000c940d8
#5 [c00000003721fbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c00000003721fc60] process_one_work at c00000000019e5c4
...
PID: 296 TASK: c000000037a65800 CPU: 21 COMMAND: "kworker/21:1"
...
#4 [c000000037247bc0] rtnl_lock at c000000000c940d8
#5 [c000000037247be0] tg3_reset_task at c008000002969358 [tg3]
#6 [c000000037247c60] process_one_work at c00000000019e5c4
...
PID: 655 TASK: c000000036f49000 CPU: 16 COMMAND: "kworker/16:2"
...:1
#4 [c0000000373ebbc0] rtnl_lock at c000000000c940d8
#5 [c0000000373ebbe0] tg3_reset_task at c008000002969358 [tg3]
#6 [c0000000373ebc60] process_one_work at c00000000019e5c4
...
Code inspection shows that both tg3_io_error_detected() and
tg3_reset_task() attempt to acquire the RTNL lock at the beginning of
their code blocks. If tg3_reset_task() should happen to execute between
the times when tg3_io_error_deteced() acquires the RTNL lock and
tg3_reset_task_cancel() is called, a deadlock will occur.
Moving tg3_reset_task_cancel() call earlier within the code block, prior
to acquiring RTNL, prevents this from happening, but also exposes another
deadlock issue where tg3_reset_task() may execute AFTER
tg3_io_error_detected() has executed:
crash> foreach UN bt
PID: 159 TASK: c0000000067d2000 CPU: 9 COMMAND: "eehd"
...
#4 [c000000006867a60] rtnl_lock at c000000000c940d8
#5 [c000000006867a80] tg3_io_slot_reset at c0080000026c2ea8 [tg3]
#6 [c000000006867b00] eeh_report_reset at c00000000004de88
...
PID: 363 TASK: c000000037564000 CPU: 6 COMMAND: "kworker/6:1"
...
#3 [c000000036c1bb70] msleep at c000000000259e6c
#4 [c000000036c1bba0] napi_disable at c000000000c6b848
#5 [c000000036c1bbe0] tg3_reset_task at c0080000026d942c [tg3]
#6 [c000000036c1bc60] process_one_work at c00000000019e5c4
...
This issue can be avoided by aborting tg3_reset_task() if EEH error
recovery is already in progress.
Fixes: db84bf43ef23 ("tg3: tg3_reset_task() needs to use rtnl_lock to synchronize")
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230124185339.225806-1-drc@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Test names were being concatenated based on a offset beyond the end of
the first name, which tripped the buffer overflow detection logic:
detected buffer overflow in strnlen
[...]
Call Trace:
bnxt_ethtool_init.cold+0x18/0x18
Refactor struct hwrm_selftest_qlist_output to use an actual array,
and adjust the concatenation to use snprintf() rather than a series of
strncat() calls.
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Link: https://lore.kernel.org/lkml/Y8F%2F1w1AZTvLglFX@x1-carbon/
Tested-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Fixes: eb51365846bc ("bnxt_en: Add basic ethtool -t selftest support.")
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the commit under Fixes the page would have been released
from the pool before the napi_alloc_skb() call, so normal page
freeing was fine (released page == no longer in the pool).
After the change we just mark the page for recycling so it's still
in the pool if the skb alloc fails, we need to recycle.
Same commit added the same bug in the new bnxt_rx_multi_page_skb().
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Link: https://lore.kernel.org/r/20230111042547.987749-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent XDP multi-buffer feature has introduced regressions in the
setting of HDS and jumbo thresholds. HDS was accidentally disabled in
the nornmal mode without XDP. This patch restores jumbo HDS placement
when not in XDP mode. In XDP multi-buffer mode, HDS should be disabled
and the jumbo threshold should be set to the usable page size in the
first page buffer.
Fixes: 32861236190b ("bnxt: change receive ring space parameters")
Reviewed-by: Mohammad Shuab Siddique <mohammad-shuab.siddique@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The size of the first buffer is always page size, and the useable
space is the page size minus the offset and the skb_shared_info size.
Make sure SKB and XDP buf sizes match so that the skb_shared_info
is at the same offset seen from the SKB and XDP_BUF.
build_skb() should be passed PAGE_SIZE. xdp_init_buff() should
be passed PAGE_SIZE as well. xdp_get_shared_info_from_buff() will
automatically deduct the skb_shared_info size if the XDP buffer
has frags. There is no need to keep bp->xdp_has_frags.
Change BNXT_PAGE_MODE_BUF_SIZE to BNXT_MAX_PAGE_MODE_MTU_SBUF
since this constant is really the MTU with ethernet header size
subtracted.
Also fix the BNXT_MAX_PAGE_MODE_MTU macro with proper parentheses.
Fixes: 32861236190b ("bnxt: change receive ring space parameters")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The XDP program can change the starting address of the RX data buffer and
this information needs to be passed back from bnxt_rx_xdp() to
bnxt_rx_pkt() for the XDP_PASS case so that the SKB can point correctly
to the modified buffer address. Add back the data_ptr parameter to
bnxt_rx_xdp() to make this work.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_xdp_buff_init() does not modify the data_ptr or the len parameters,
so no need to pass in the addresses of these parameters.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't register a devlink port in case of a VF so
avoid setting the devlink pointer to netdev.
Also, SET_NETDEV_DEVLINK_PORT has to be moved
so that we determine whether the device is PF/VF first.
This fixes the NULL pointer dereference of devlink_port->devlink
when creating VFs:
BUG: kernel NULL pointer dereference, address: 0000000000000160
PGD 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 14 PID: 388 Comm: kworker/14:1 Kdump: loaded Not tainted 6.1.0-rc8 #5
Hardware name: Dell Inc. PowerEdge R750/06V45N, BIOS 1.3.8 08/31/2021
Workqueue: events work_for_cpu_fn
RIP: 0010:devlink_nl_port_handle_size+0xb/0x50
Code: 83 c4 10 5b 5d c3 cc cc cc cc b8 a6 ff ff ff eb de e8 c9 59 21 00 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 55 53 48 8b 47 20 <48> 8b a8 60 01 00 00 48 8b 45 60 48 8b 38 e8 92 90 1a 00 48 8b 7d
RSP: 0018:ff4fe5394846fcd8 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000794 RCX: 0000000000000000
RDX: ff1f129683a30a40 RSI: 0000000000000008 RDI: ff1f1296bb496188
RBP: 0000000000000334 R08: 0000000000000cc0 R09: 0000000000000000
R10: ff1f1296bb494298 R11: ffffffffffffffc0 R12: 0000000000000000
R13: 0000000000000000 R14: ff1f1296bb494000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ff1f129e5fa00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000160 CR3: 000000131f610006 CR4: 0000000000771ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
if_nlmsg_size+0x14a/0x220
rtmsg_ifinfo_build_skb+0x3c/0x100
rtmsg_ifinfo+0x9c/0xc0
register_netdevice+0x59d/0x670
register_netdev+0x1c/0x40
bnxt_init_one+0x674/0xa60 [bnxt_en]
local_pci_probe+0x42/0x80
work_for_cpu_fn+0x13/0x20
process_one_work+0x1e2/0x3b0
? rescuer_thread+0x390/0x390
worker_thread+0x1c4/0x3a0
? rescuer_thread+0x390/0x390
kthread+0xd6/0x100
? kthread_complete_and_exit+0x20/0x20
Fixes: ac73d4bf2cda ("net: make drivers to use SET_NETDEV_DEVLINK_PORT to set devlink_port")
Cc: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- reduce the swiotlb buffer size on allocation failure (Alexey
Kardashevskiy)
- clean up passing of bogus GFP flags to the dma-coherent allocator
(Christoph Hellwig)
* tag 'dma-mapping-6.2-2022-12-13' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject __GFP_COMP in dma_alloc_attrs
ALSA: memalloc: don't pass bogus GFP_ flags to dma_alloc_*
s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent
cnic: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/qib: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/hfi1: don't pass bogus GFP_ flags to dma_alloc_coherent
media: videobuf-dma-contig: use dma_mmap_coherent
swiotlb: reduce the swiotlb buffer size on allocation failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
|
|
Eric Dumazet implemented Big TCP that allowed bigger TSO/GRO packet sizes
for IPv6 traffic. See patch series:
'commit 89527be8d8d6 ("net: add IFLA_TSO_{MAX_SIZE|SEGS} attributes")'
This reduces the number of packets traversing the networking stack and
should usually improves performance. However, it also inserts a
temporary Hop-by-hop IPv6 extension header.
Using the HBH header removal method in the previous patch, the extra header
be removed in bnxt drivers to allow it to send big TCP packets (bigger
TSO packets) as well.
Tested:
Compiled locally
To further test functional correctness, update the GSO/GRO limit on the
physical NIC:
ip link set eth0 gso_max_size 181000
ip link set eth0 gro_max_size 181000
Note that if there are bonding or ipvan devices on top of the physical
NIC, their GSO sizes need to be updated as well.
Then, IPv6/TCP packets with sizes larger than 64k can be observed.
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20221210041646.3587757-2-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller reported:
BUG: KASAN: slab-out-of-bounds in __build_skb_around+0x235/0x340 net/core/skbuff.c:294
Write of size 32 at addr ffff88802aa172c0 by task syz-executor413/5295
For bpf_prog_test_run_skb(), which uses a kmalloc()ed buffer passed to
build_skb().
When build_skb() is passed a frag_size of 0, it means the buffer came
from kmalloc. In these cases, ksize() is used to find its actual size,
but since the allocation may not have been made to that size, actually
perform the krealloc() call so that all the associated buffer size
checking will be correctly notified (and use the "new" pointer so that
compiler hinting works correctly). Split this logic out into a new
interface, slab_build_skb(), but leave the original 0 checking for now
to catch any stragglers.
Reported-by: syzbot+fda18eaa8c12534ccb3b@syzkaller.appspotmail.com
Link: https://groups.google.com/g/syzkaller-bugs/c/UnIKxTtU5-0/m/-wbXinkgAQAJ
Fixes: 38931d8989b5 ("mm: Make ksize() a reporting-only function")
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: pepsipu <soopthegoop@gmail.com>
Cc: syzbot+fda18eaa8c12534ccb3b@syzkaller.appspotmail.com
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: kasan-dev <kasan-dev@googlegroups.com>
Cc: Andrii Nakryiko <andrii@kernel.org>
Cc: ast@kernel.org
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hao Luo <haoluo@google.com>
Cc: Jesper Dangaard Brouer <hawk@kernel.org>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: jolsa@kernel.org
Cc: KP Singh <kpsingh@kernel.org>
Cc: martin.lau@linux.dev
Cc: Stanislav Fomichev <sdf@google.com>
Cc: song@kernel.org
Cc: Yonghong Song <yhs@fb.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221208060256.give.994-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function dmadesc_get_addr() is defined in the bcmgenet.c file, but
not called elsewhere, so remove this unused function.
drivers/net/ethernet/broadcom/genet/bcmgenet.c:120:26: warning: unused function 'dmadesc_get_addr'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3401
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221209033723.32452-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I must have missed that these stats are only exposed
via the unstructured ethtool -S when they got merged.
Plumb in the structured form.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20221130013108.90062-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver name is available in device_driver::name. Right now,
drivers still have to report this piece of information themselves in
their devlink_ops::info_get callback function.
In order to factorize code, make devlink_nl_info_fill() add the driver
name attribute.
Now that the core sets the driver name attribute, drivers are not
supposed to call devlink_info_driver_name_put() anymore. Remove
devlink_info_driver_name_put() and clean-up all the drivers using this
function in their callback.
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Tested-by: Ido Schimmel <idosch@nvidia.com> # mlxsw
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ARCH_BCM2835
commit 8d820bc9d12b ("net: broadcom: Fix BCMGENET Kconfig") fixes the build
that contain 99addbe31f55 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
and enable BCMGENET=y but PTP_1588_CLOCK_OPTIONAL=m, which otherwise
leads to a link failure. However this may trigger a runtime failure.
Fix the original issue by propagating the PTP_1588_CLOCK_OPTIONAL dependency
of BROADCOM_PHY down to BCMGENET.
Fixes: 8d820bc9d12b ("net: broadcom: Fix BCMGENET Kconfig")
Fixes: 99addbe31f55 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221125115003.30308-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tools/lib/bpf/ringbuf.c
927cbb478adf ("libbpf: Handle size overflow for ringbuf mmap")
b486d19a0ab0 ("libbpf: checkpatch: Fixed code alignments in ringbuf.c")
https://lore.kernel.org/all/20221121122707.44d1446a@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.
Fixes: b56e9670ffa4 ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
