| Age | Commit message (Collapse) | Author |
|---|
|
Fix the sequence required for PCIE-AER. While slot reset occurs, firmware
might not be ready and the driver needs to check for its recovery. We
also need to remap the health registers for some chips and clear the
resource reservations. The resources will be allocated again during
bnxt_io_resume().
Fixes: fb1e6e562b37 ("bnxt_en: Fix AER recovery.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When polling for the firmware message response, we first poll for the
response message header. Once the valid length is detected in the
header, we poll for the valid bit at the end of the message which
signals DMA completion. Normally, this poll time for DMA completion
is extremely short (0 to a few usec). But on some devices under some
rare conditions, it can be up to about 20 msec.
Increase this delay to 50 msec and use udelay() for the first 10 usec
for the common case, and usleep_range() beyond that.
Also, change the error message to include the above delay time when
printing the timeout value.
Fixes: 3c8c20db769c ("bnxt_en: move HWRM API implementation into separate file")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b05e ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Parameter names in the comments did not match the function arguments.
Fixes: 213808170840 ("bnxt_en: add support for HWRM request slices")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reported-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210901185315.57137-1-edwin.peer@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add infrastructure to maintain a pending list of HWRM commands awaiting
completion and reduce the scope of the hwrm_cmd_lock mutex so that it
protects only the request mailbox. The mailbox is free to use for one
or more concurrent commands after receiving deferred response events.
For uniformity and completeness, use the same pending list for
collecting completions for commands that respond via a completion ring.
These commands are only used for freeing rings and for IRQ test and
we only support one such command in flight.
Note deferred responses are also only supported on the main channel.
The secondary channel (KONG) does not support deferred responses.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no longer any callers relying on the old API.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slices are a mechanism for suballocating DMA mapped regions from the
request buffer. Such regions can be used for indirect command data
instead of creating new mappings with dma_alloc_coherent().
The advantage of using a slice is that the lifetime of the slice is
bound to the request and will be automatically unmapped when the
request is consumed.
A single external region is also supported. This allows for regions
that will not fit inside the spare request buffer space such that
the same API can be used consistently even for larger mappings.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hwrm_req_replace() provides an assignment like operation to replace a
managed HWRM request object with data from a pre-built source. This is
useful for handling request data provided by higher layer HWRM clients.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During firmware crash recovery, it is possible for firmware to respond
to stale HWRM commands that have already timed out. Because response
buffers may be reused, any out of sequence responses need to be ignored
and only the matching seq_id should be accepted.
Also, READ_ONCE should be used for the reads from the DMA buffer to
ensure that the necessary loads are scheduled.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change constitutes a major step towards supporting multiple
firmware commands in flight by maintaining a separate response buffer
for the duration of each request. These firmware commands are also
known as Hardware Resource Manager (HWRM) commands. Using separate
response buffers requires an API change in order for callers to be
able to free the buffer when done.
It is impossible to keep the existing APIs unchanged. The existing
usage for a simple HWRM message request such as the following:
struct input req = {0};
bnxt_hwrm_cmd_hdr_init(bp, &req, REQ_TYPE, -1, -1);
rc = hwrm_send_message(bp, &req, sizeof(req), HWRM_CMD_TIMEOUT);
if (rc)
/* error */
changes to:
struct input *req;
rc = hwrm_req_init(bp, req, REQ_TYPE);
if (rc)
/* error */
rc = hwrm_req_send(bp, req); /* consumes req */
if (rc)
/* error */
The key changes are:
1. The req is no longer allocated on the stack.
2. The caller must call hwrm_req_init() to allocate a req buffer and
check for a valid buffer.
3. The req buffer is automatically released when hwrm_req_send() returns.
4. If the caller wants to check the firmware response, the caller must
call hwrm_req_hold() to take ownership of the response buffer and
release it afterwards using hwrm_req_drop(). The caller is no longer
required to explicitly hold the hwrm_cmd_lock mutex to read the
response.
5. Because the firmware commands and responses all have different sizes,
some safeguards are added to the code.
This patch maintains legacy API compatibiltiy, implementing the old
API in terms of the new. The follow-on patches will convert all
callers to use the new APIs.
v2: Fix redefined writeq with parisc .config
Fix "cast from pointer to integer of different size" warning in
hwrm_calc_sentinel()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
