| Age | Commit message (Collapse) | Author |
|---|
|
Eric points out that we should make sure that ring index updates
are wrapped in the appropriate READ_ONCE/WRITE_ONCE macros.
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_fw_to_ethtool_speed() is missing the case statement for 200G
link speed reported by firmware. As a result, ethtool will report
unknown speed when the firmware reports 200G link speed.
Fixes: 532262ba3b84 ("bnxt_en: ethtool: support PAM4 link speeds up to 200G")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver uses the flag BNXT_FLAG_MULTI_HOST to determine whether
to use non-realtime mode PHC when running on a multi host NIC.
However when ptp initializes on a NIC with shared PHC, we still
don't have this flag set yet because HWRM_FUNC_QCFG is issued
much later.
Move the ptp initialization code after we have issued func_qcfg.
The next patch will use the BNXT_FLAG_MULTI_HOST flag during PTP
initialization.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current fw_cap field (u32) has run out of bits to save any
new capability.
Change the field to u64.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using a PHC in shared between multiple hosts, the previous
frequency value may not be reset and could lead to host being unable to
compensate the offset with timecounter adjustments. To avoid such state
reset the hardware frequency of PHC to zero on init. Some refactoring is
needed to make code readable.
Fixes: 85036aee1938 ("bnxt_en: Add a non-real time mode to access NIC clock")
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20230310151356.678059-1-vadfed@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add auxiliary driver support.
An auxiliary device will be created if the hardware indicates
support for RDMA.
The bnxt_ulp_probe() function has been removed and a new
bnxt_rdma_aux_device_add() function has been added.
The bnxt_free_msix_vecs() and bnxt_req_msix_vecs() will now hold
the RTNL lock when they call the bnxt_close_nic()and bnxt_open_nic()
since the device close and open need to be protected under RTNL lock.
The operations between the bnxt_en and bnxt_re will be protected
using the en_ops_lock.
This will be used by the bnxt_re driver in a follow-on patch
to create ROCE interfaces.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The size of the first buffer is always page size, and the useable
space is the page size minus the offset and the skb_shared_info size.
Make sure SKB and XDP buf sizes match so that the skb_shared_info
is at the same offset seen from the SKB and XDP_BUF.
build_skb() should be passed PAGE_SIZE. xdp_init_buff() should
be passed PAGE_SIZE as well. xdp_get_shared_info_from_buff() will
automatically deduct the skb_shared_info size if the XDP buffer
has frags. There is no need to keep bp->xdp_has_frags.
Change BNXT_PAGE_MODE_BUF_SIZE to BNXT_MAX_PAGE_MODE_MTU_SBUF
since this constant is really the MTU with ethernet header size
subtracted.
Also fix the BNXT_MAX_PAGE_MODE_MTU macro with proper parentheses.
Fixes: 32861236190b ("bnxt: change receive ring space parameters")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/can/pch_can.c
ae64438be192 ("can: dev: fix skb drop check")
1dd1b521be85 ("can: remove obsolete PCH CAN driver")
https://lore.kernel.org/all/20221110102509.1f7d63cc@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hardware is unable to realize all legal firmware interface state values
for hash_type. For example, if 4-tuple TCP_IPV4 hash is enabled,
4-tuple UDP_IPV4 hash must also be enabled. By providing the bits the
user intended to change instead of the possible illegal intermediate
states, the firmware is able to make better compromises when deciding
which bits to ignore.
With this new mechansim, we can now report the actual configured hash
back to the user. Add bnxt_hwrm_update_rss_hash_cfg() to report the
actual hash after user configuration.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix the sequence required for PCIE-AER. While slot reset occurs, firmware
might not be ready and the driver needs to check for its recovery. We
also need to remap the health registers for some chips and clear the
resource reservations. The resources will be allocated again during
bnxt_io_resume().
Fixes: fb1e6e562b37 ("bnxt_en: Fix AER recovery.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for .get_module_eeprom_by_page() callback which
implements generic solution for module`s eeprom access.
v3: Add bnxt_get_module_status() to get a more specific extack error
string.
Return -EINVAL from bnxt_get_module_eeprom_by_page() when we
don't want to fallback to old method.
v2: Simplification suggested by Ido Schimmel
Link: https://lore.kernel.org/netdev/YzVJ%2FvKJugoz15yV@shredder/
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using BNXT_PAGE_MODE_BUF_SIZE + offset as buffer length value is not
sufficient when running single buffer XDP programs doing redirect
operations. The stack will complain on missing skb tail room. Fix it
by using PAGE_SIZE when calling xdp_init_buff() for single buffer
programs.
Fixes: b231c3f3414c ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If bnxt_sriov_enable() fails after some resources have been reserved
for the VFs, the current code is not unwinding properly and the
reserved resources become unavailable afterwards. Fix it by
properly unwinding with a call to bnxt_hwrm_func_qcaps() to
reset all maximum resources.
Also, add the missing bnxt_ulp_sriov_cfg() call to let the RDMA
driver know to abort.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add driver support to enable timestamping on all RX packets
that are received by the NIC. This capability can be requested
by the applications using SIOCSHWTSTAMP ioctl with filter type
HWTSTAMP_FILTER_ALL.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the following features:
- Support for XDP_TX and XDP_DROP action when using xdp_buff
with frags
- Support for freeing all frags attached to an xdp_buff
- Cleanup of TX ring buffers after transmits complete
- Slight change in definition of bnxt_sw_tx_bd since nr_frags
and RX producer may both need to be used
- Clear out skb_shared_info at the end of the buffer
v2: Fix uninitialized variable warning in bnxt_xdp_buff_frags_free().
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify ring header data split and jumbo parameters to account
for the fact that the design for XDP multibuffer puts close to
the first 4k of data in a page and the remaining portions of
the packet go in the aggregation ring.
v3: Simplified code around initial buffer size calculation
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move initialization of xdp_buff outside of bnxt_rx_xdp to prepare
for allowing bnxt_rx_xdp to operate on multibuffer xdp_buffs.
v2: Fix uninitalized variables warning in bnxt_xdp.c.
v3: Add new define BNXT_PAGE_MODE_BUF_SIZE
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are more CPUs than the number of TX XDP rings, multiple XDP
redirects can select the same TX ring based on the CPU on which
XDP redirect is called. Add locking when needed and use static
key to decide whether to take the lock.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In prep for .eswitch_mode_set being called with the devlink instance
lock held use that lock explicitly instead of creating a local mutex
just for the sriov reconfig.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts:
commit 02acd399533e ("bnxt_en: parse result field when NVRAM package install fails")
commit 22f5dba5065d ("bnxt_en: add an nvm test for hw diagnose")
commit bafed3f231f7 ("bnxt_en: implement hw health reporter")
These patches are still under discussion / I don't think they
are right, and since the authors don't reply promptly let me
lessen my load of "things I need to resolve before next release"
and revert them.
Acked-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220308173659.304915-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add an NVM test function for devlink hw reporter.
In this function an NVM VPD area is read followed by
a write. Test result is cached and if it is successful then
the next test can be conducted only after HW_RETEST_MIN_TIME to
avoid frequent writes to the NVM.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reporter will report NVM errors which are non-fatal.
When we receive these NVM error events, we'll report it
through this new hw health reporter.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some cards are configured to never support link pause or PFC. Discover
these cards and properly report no pause support to ethtool. Disable
PFC settings from DCBNL if PFC is unsupported.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will force link state to always be logged for initial NIC open.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/mptcp/mptcp_join.sh
34aa6e3bccd8 ("selftests: mptcp: add ip mptcp wrappers")
857898eb4b28 ("selftests: mptcp: add missing join check")
6ef84b1517e0 ("selftests: mptcp: more robust signal race test")
https://lore.kernel.org/all/20220221131842.468893-1-broonie@kernel.org/
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/act.h
drivers/net/ethernet/mellanox/mlx5/core/en/tc/act/ct.c
fb7e76ea3f3b6 ("net/mlx5e: TC, Skip redundant ct clear actions")
c63741b426e11 ("net/mlx5e: Fix MPLSoUDP encap to use MPLS action information")
09bf97923224f ("net/mlx5e: TC, Move pedit_headers_action to parse_attr")
84ba8062e383 ("net/mlx5e: Test CT and SAMPLE on flow attr")
efe6f961cd2e ("net/mlx5e: CT, Don't set flow flag CT for ct clear flow")
3b49a7edec1d ("net/mlx5e: TC, Reject rules with multiple CT actions")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the current code, we setup the port to PHY or MAC loopback mode
and then transmit a test broadcast packet for the loopback test. This
scheme fails sometime if the port is shared with management firmware
that can also send packets. The driver may receive the management
firmware's packet and the test will fail when the contents don't
match the test packet.
Change the test packet to use it's own MAC address as the destination
and setup the port to only receive it's own MAC address. This should
filter out other packets sent by management firmware.
Fixes: 91725d89b97a ("bnxt_en: Add PHY loopback to ethtool self-test.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTC mode if it is supported by firmware. In RTC
mode, the PHC is set to the 64-bit clock. Because the legacy interface
is 48-bit, the driver still has to keep track of the upper 16 bits and
handle the rollover.
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 881d8353b05e ("bnxt_en: Add an upper bound for all firmware command timeouts.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CQE coalescing mode is the same as the timer reset coalescing mode
on Broadcom devices. Currently this mode is always enabled if it
is supported by the device. Restructure the code slightly to support
dynamically changing this mode.
Add a flags field to struct bnxt_coal. Initially, the CQE flag will
be set for the RX and TX side if the device supports it. We need to
move bnxt_init_dflt_coal() to set up default coalescing until the
capability is determined.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bp->sriov_cfg is not defined when CONFIG_BNXT_SRIOV is not set. Fix
it by adding a helper function bnxt_sriov_cfg() to handle the logic
with or without the config option.
Fixes: 46d08f55d24e ("bnxt_en: extend RTNL to VF check in devlink driver_reinit")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1637090770-22835-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Live patches are activated by using the 'limit no_reset' option when
performing a devlink dev reload fw_activate operation. These packages
must first be installed on the device in the usual way. For example,
via devlink dev flash or ethtool -f.
The devlink device info has also been enhanced to render stored and
running live patch versions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main changes are firmware live patch support and 2 additional FEC
standard counters.
Add the matching FEC counters to ethtool counter array. Firmware older
than 220 does not return the proper size of the extended RX counters so
we need to cap it at the smaller legacy size. Otherwise the new FEC
counters may show up with garbage values.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent firmware provides coredump and crashdump size info via
DBG_QCFG command. Read the dump sizes from firmware, instead of
computing in the driver. This patch reduces the time taken
to collect the dump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add firmware event counters as well as health state severity. In
the unhealthy state, recommend a remedy and inform the user as to
its impact.
Readability of the devlink tool's output is negatively impacted by
adding these fields to the diagnosis. The single line of text, as
rendered by devlink health diagnose, benefits from more terse
descriptions, which can be substituted without loss of clarity, even
in pretty printed JSON mode.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'fw' and 'fw_fatal' health reporters. There is no longer a need
to distinguish between firmware reporters. Only bonafide errors are
reported now and no reports were being generated for the 'fw' reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware resets initiated by the user are not errors and should not
be reported via devlink. Once only unsolicited resets remain, it is no
longer sensible to maintain a separate fw_reset reporter.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recovery election messages are often mistaken for errors. Improve
the wording to clarify the meaning of these frequent and expected
events. Also, take the first step towards more inclusive language.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reported parameter value should not take into account the state
of remote drivers. Firmware will reject remote resets as appropriate,
thus it is not strictly necessary to check HOT_RESET_ALLOWED before
attempting to initiate a reset. But we add the check so that we can
provide more intuitive messages when reset is not permitted.
This firmware setting needs to be restored from all functions after
a firmware reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to reload driver_reinit, the RTNL lock is held across reload
down and up to prevent interleaving state changes. But we need to
subsequently release the RTNL lock while waiting for firmware reset
to complete.
Also keep a statistic on fw_activate resets initiated remotely from
other functions.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTNL lock must be held between down and up to prevent interleaving
state changes, especially since external state changes might release
and allocate different driver resource subsets that would otherwise
need to be tracked and carefully handled. If the down function fails,
then devlink will not call the corresponding up function, thus the
lock is released in the down error paths.
v2: Don't use devlink_reload_disable() and devlink_reload_enable().
Instead, check that the netdev is not in unregistered state before
proceeding with reload.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-Off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resource reservations will also need to be reset after FUNC_DRV_UNRGTR
in the following devlink driver_reinit patch. Extract this logic into a
reusable function.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device info logged during probe will be reused by the devlink
driver_reinit code in a following patch. Extract this logic into
the new bnxt_print_device_info() function. The board index needs
to be saved in the driver context so that the board information
can be retrieved at a later time, outside of the probe function.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smallest TX ring size we support must fit a TX SKB with MAX_SKB_FRAGS
+ 1. Because the first TX BD for a packet is always a long TX BD, we
need an extra TX BD to fit this packet. Define BNXT_MIN_TX_DESC_CNT with
this value to make this more clear. The current code uses a minimum
that is off by 1. Fix it using this constant.
The tx_wake_thresh to determine when to wake up the TX queue is half the
ring size but we must have at least BNXT_MIN_TX_DESC_CNT for the next
packet which may have maximum fragments. So the comparison of the
available TX BDs with tx_wake_thresh should be >= instead of > in the
current code. Otherwise, at the smallest ring size, we will never wake
up the TX queue and will cause TX timeout.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver requires 64-bit doorbell writes to be atomic on 32-bit
architectures. So we redefined writeq as a new macro with spinlock
protection on 32-bit architectures. This created a new warning when
we added a new file in a recent patchset. writeq is defined on many
32-bit architectures to do the memory write non-atomically and it
generated a new macro redefined warning. This warning was fixed
incorrectly in the recent patch.
Fix this properly by adding a new bnxt_writeq() function that will
do the non-atomic write under spinlock on 32-bit systems. All callers
in the driver will now call bnxt_writeq() instead.
v2: Need to pass in bp to bnxt_writeq()
Use lo_hi_writeq() [suggested by Florian]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: f9ff578251dc ("bnxt_en: introduce new firmware message API based on DMA pools")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add infrastructure to maintain a pending list of HWRM commands awaiting
completion and reduce the scope of the hwrm_cmd_lock mutex so that it
protects only the request mailbox. The mailbox is free to use for one
or more concurrent commands after receiving deferred response events.
For uniformity and completeness, use the same pending list for
collecting completions for commands that respond via a completion ring.
These commands are only used for freeing rings and for IRQ test and
we only support one such command in flight.
Note deferred responses are also only supported on the main channel.
The secondary channel (KONG) does not support deferred responses.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are no longer any callers relying on the old API.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
