| Age | Commit message (Collapse) | Author |
|---|
|
With the addition of entries in the phy speed/duplex settings
array to support KR and KX mode, the work-around to add/remove
baseT settings to run at a fixed speed is no longer needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Checkpatch issued a warning preferring to use kstrto<type> when
using a single variable sscanf. Change the sscanf invocation to
a kstrtouint call.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver makes use of the additional mac address
registers in the hardware to provide perfect filtering. The
hardware can also have a set of hash table registers that can
be used for imperfect filtering. By using imperfect filtering
the additional mac address registers can be used for layer 2
filtering support. Use the hash table registers if the device
has them.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for (imperfect) filtering of
VLAN tag ids using a 16-bit filter hash table. When
VLANs are added, a 4-bit hash is calculated with the
result indicating the bit in the hash table to set.
This table is used by the hardware to drop packets with
a VLAN id that does not hash to a set bit in the table.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a VLAN packet check to be sure that VLAN
RX CTAG stripping is enabled before indicating that the
tag has been stripped in the packet information data
structure.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC_VLAN_Incl register (0x0060) must be set to indicate
that the VLAN tag to be inserted comes from a Tx context
descriptor and not the MAC_VLAN_Incl register. Also, even
though it is the default, explicitly set the type of tag to
be inserted as a CTAG.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to avoid conflicts with other include files, add
a prefix to the defines in xgbe.h.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a typo here so we return directly instead of unwinding.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture. Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
