| Age | Commit message (Collapse) | Author |
|---|
|
This change does not fix any functional issue or address any real life
use case that wasn't possible before. It is just a small step in the
process of standardizing the way in which Ethernet MAC drivers may apply
RGMII delays (traditionally these have been applied by PHYs, with no
clear definition of what to do in the case of a fixed-link).
The sja1105 driver used to apply MAC-level RGMII delays on the RX data
lines when in fixed-link mode and using a phy-mode of "rgmii-rxid" or
"rgmii-id" and on the TX data lines when using "rgmii-txid" or "rgmii-id".
But the standard definitions don't say anything about behaving
differently when the port is in fixed-link vs when it isn't, and the new
device tree bindings are about having a way of applying the delays in a
way that is independent of the phy-mode and of the fixed-link property.
When the {rx,tx}-internal-delay-ps properties are present, use them,
otherwise fall back to the old behavior and warn.
One other thing to note is that the SJA1105 hardware applies a delay
value in degrees rather than in picoseconds (the delay in ps changes
depending on the frequency of the RGMII clock - 125 MHz at 1G, 25 MHz at
100M, 2.5MHz at 10M). I assume that is fine, we calculate the phase
shift of the internal delay lines assuming that the device tree meant
gigabit, and we let the hardware scale those according to the link speed.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210723173108.459770-6-prasanna.vengateshan@microchip.com/
Link: https://patchwork.ozlabs.org/project/netdev/patch/20200616074955.GA9092@laureti-dev/#2461123
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix delay settings applied to wrong cpu in parse_port_config. The delay
values is set to the wrong index as the cpu_port_index is incremented
too early. Start the cpu_port_index to -1 so the correct value is
applied to address also the case with invalid phy mode and not available
port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed based on a
GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found
in the OpenWrt source tree.
Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb
subdriver. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.
The RTL8365MB-VC switch is capable of offloading a large number of
features from the software, but this patch introduces only the most
basic DSA driver functionality. The ports always function as standalone
ports, with bridging handled in software.
One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.
Co-developed-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Michael Rasmussen <mir@bang-olufsen.dk>
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move ports related config to dedicated struct to keep things organized.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCA original code report port instability and sa that SGMII also require
to set internal delay. Generalize the rgmii delay function and apply the
advised value if they are not defined in DT.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCA8328 switch is the bigger brother of the qca8327. Same regs different
chip. Change the function to set the correct pin layout and introduce a
new match_data to differentiate the 2 switch as they have the same ID
and their internal PHY have the same ID.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some qca8327 switch require to force the ignore of power on sel
strapping. Some switch require to set the led open drain mode in regs
instead of using strapping. While most of the device implements this
using the correct way using pin strapping, there are still some broken
device that require to be set using sw regs.
Introduce a new binding and support these special configuration.
As led open drain require to ignore pin strapping to work, the probe
fails with EINVAL error with incorrect configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support enabling PLL on the SGMII CPU port. Some device require this
special configuration or no traffic is transmitted and the switch
doesn't work at all. A dedicated binding is added to the CPU node
port to apply the correct reg on mac config.
Fail to correctly configure sgmii with qca8327 switch and warn if pll is
used on qca8337 with a revision greater than 1.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Future proof commit. This switch have 2 CPU ports and one valid
configuration is first CPU port set to sgmii and second CPU port set to
rgmii-id. The current implementation detects delay only for CPU port
zero set to rgmii and doesn't count any delay set in a secondary CPU
port. Drop the current delay scan function and move it to the sgmii
parser function to generalize and implicitly add support for secondary
CPU port set to rgmii-id. Introduce new logic where delay is enabled
also with internal delay binding declared and rgmii set as PHY mode.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently CPU port is always hardcoded to port 0. This switch have 2 CPU
ports. The original intention of this driver seems to be use the
mac06_exchange bit to swap MAC0 with MAC6 in the strange configuration
where device have connected only the CPU port 6. To skip the
introduction of a new binding, rework the driver to address the
secondary CPU port as primary and drop any reference of hardcoded port.
With configuration of mac06 exchange, just skip the definition of port0
and define the CPU port as a secondary. The driver will autoconfigure
the switch to use that as the primary CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for this in the qca8k driver. Also add support for SGMII
rx/tx clock falling edge. This is only present for pad0, pad5 and
pad6 have these bit reserved from Documentation. Add a comment that this
is hardcoded to PAD0 as qca8327/28/34/37 have an unique sgmii line and
setting falling in port0 applies to both configuration with sgmii used
for port0 or port6.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing mac power sel support needed for ipq8064/5 SoC that require
1.8v for the internal regulator port instead of the default 1.5v.
If other device needs this, consider adding a dedicated binding to
support this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tools/testing/selftests/net/ioam6.sh
7b1700e009cc ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a56 ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The NXP LS1028A switch has two Ethernet ports towards the CPU, but only
one of them is capable of acting as an NPI port at a time (inject and
extract packets using DSA tags).
However, using the alternative ocelot-8021q tagging protocol, it should
be possible to use both CPU ports symmetrically, but for that we need to
mark both ports in the device tree as DSA masters.
In the process of doing that, it can be seen that traffic to/from the
network stack gets broken, and this is because the Felix driver iterates
through all DSA CPU ports and configures them as NPI ports. But since
there can only be a single NPI port, we effectively end up in a
situation where DSA thinks the default CPU port is the first one, but
the hardware port configured to be an NPI is the last one.
I would like to treat this as a bug, because if the updated device trees
are going to start circulating, it would be really good for existing
kernels to support them, too.
Fixes: adb3dccf090b ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At present, when a PTP packet which requires TX timestamping gets
dropped under congestion by the switch, things go downhill very fast.
The driver keeps a clone of that skb in a queue of packets awaiting TX
timestamp interrupts, but interrupts will never be raised for the
dropped packets.
Moreover, matching timestamped packets to timestamps is done by a 2-bit
timestamp ID, and this can wrap around and we can match on the wrong skb.
Since with the default NPI-based tagging protocol, we get no notification
about packet drops, the best we can do is eventually recover from the
drop of a PTP frame: its skb will be dead memory until another skb which
was assigned the same timestamp ID happens to find it.
However, with the ocelot-8021q tagger which injects packets using the
manual register interface, it appears that we can check for more
information, such as:
- whether the input queue has reached the high watermark or not
- whether the injection group's FIFO can accept additional data or not
so we know that a PTP frame is likely to get dropped before actually
sending it, and drop it ourselves (because DSA uses NETIF_F_LLTX, so it
can't return NETDEV_TX_BUSY to ask the qdisc to requeue the packet).
But when we do that, we can also remove the skb from the timestamping
queue, because there surely won't be any timestamp that matches it.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae21 ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.
This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).
I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.
Fixes: 4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1ba3 ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_ppu_updates() interpretes data in the PORT_STS
register incorrectly for internal ports (ie no PPU). In these
cases, the PHY_DETECT bit indicates link status. This results
in forcing the MAC state whenever the PHY link goes down which
is not intended. As a side effect, LED's configured to show
link status stay lit even though the physical link is down.
Add a check in mac_link_down and mac_link_up to see if it
concerns an external port and only then, look at PPU status.
Fixes: 5d5b231da7ac (net: dsa: mv88e6xxx: use PHY_DETECT in mac_link_up/mac_link_down)
Reported-by: Maarten Zanders <m.zanders@televic.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 6087175b7991 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6a8 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The VLAN support in mv88e6xxx has a loaded history. Commit 2ea7a679ca2a
("net: dsa: Don't add vlans when vlan filtering is disabled") noticed
some issues with VLAN and decided the best way to deal with them was to
make the DSA core ignore VLANs added by the bridge while VLAN awareness
is turned off. Those issues were never explained, just presented as
"at least one corner case".
That approach had problems of its own, presented by
commit 54a0ed0df496 ("net: dsa: provide an option for drivers to always
receive bridge VLANs") for the DSA core, followed by
commit 1fb74191988f ("net: dsa: mv88e6xxx: fix vlan setup") which
applied ds->configure_vlan_while_not_filtering = true for mv88e6xxx in
particular.
We still don't know what corner case Andrew saw when he wrote
commit 2ea7a679ca2a ("net: dsa: Don't add vlans when vlan filtering is
disabled"), but Tobias now reports that when we use TX forwarding
offload, pinging an external station from the bridge device is broken if
the front-facing DSA user port has flooding turned off. The full
description is in the link below, but for short, when a mv88e6xxx port
is under a VLAN-unaware bridge, it inherits that bridge's pvid.
So packets ingressing a user port will be classified to e.g. VID 1
(assuming that value for the bridge_default_pvid), whereas when
tag_dsa.c xmits towards a user port, it always sends packets using a VID
of 0 if that port is standalone or under a VLAN-unaware bridge - or at
least it did so prior to commit d82f8ab0d874 ("net: dsa: tag_dsa:
offload the bridge forwarding process").
In any case, when there is a conversation between the CPU and a station
connected to a user port, the station's MAC address is learned in VID 1
but the CPU tries to transmit through VID 0. The packets reach the
intended station, but via flooding and not by virtue of matching the
existing ATU entry.
DSA has established (and enforced in other drivers: sja1105, felix,
mt7530) that a VLAN-unaware port should use a private pvid, and not
inherit the one from the bridge. The bridge's pvid should only be
inherited when that bridge is VLAN-aware, so all state transitions need
to be handled. On the other hand, all bridge VLANs should sit in the VTU
starting with the moment when the bridge offloads them via switchdev,
they are just not used.
This solves the problem that Tobias sees because packets ingressing on
VLAN-unaware user ports now get classified to VID 0, which is also the
VID used by tag_dsa.c on xmit.
Fixes: d82f8ab0d874 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003222312.284175-2-vladimir.oltean@nxp.com/#24491503
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eliminate the following coccicheck warning:
./drivers/net/dsa/rtl8366rb.c:1348:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for setting the STP state to the RTL8366RB
DSA switch. This rids the following message from the kernel on
e.g. OpenWrt:
DSA: failed to set STP state 3 (-95)
Since the RTL8366RB has one STP state register per FID with
two bit per port in each, we simply loop over all the FIDs
and set the state on all of them.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements fast aging per-port using the special "security"
register, which will flush any learned L2 LUT entries on a port.
The vendor API just enabled setting and clearing this bit, so
we set it to age out any entries on the port and then we clear
it again.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTL8366RB hardware supports disabling learning per-port
so let's make use of this feature. Rename some unfortunately
named registers in the process.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/phy/bcm7xxx.c
d88fd1b546ff ("net: phy: bcm7xxx: Fixed indirect MMD operations")
f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165")
net/sched/sch_api.c
b193e15ac69d ("net: prevent user from passing illegal stab size")
69508d43334e ("net_sched: Use struct_size() and flex_array_size() helpers")
Both cases trivial - adjacent code additions.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We added a state variable to track whether a certain port
was VLAN filtering or not, but we can just inquire the DSA
core about this.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need a message for every VLAN association, dbg
is fine. The message about adding the DSA or CPU
port to a VLAN is directly misleading, this is perfectly
fine.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were checking that the MC (member config) was != 0
for some reason, all we need to check is that the config
has no ports, i.e. no members. Then it can be recycled.
This must be some misunderstanding.
Fixes: 4ddcaf1ebb5e ("net: dsa: rtl8366: Properly clear member config")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While we were defining one VLAN per port for isolating the ports
the port_vlan_filtering() callback was implemented to enable a
VLAN on the port + 1. This function makes no sense, not only is
it incomplete as it only enables the VLAN, it doesn't do what
the callback is supposed to do, which is to selectively enable
and disable filtering on a certain port.
Implement the correct callback: we have two registers dealing
with filtering on the RTL9366RB, so we implement an ASIC-specific
callback and implement filering using the register bit that makes
the switch drop frames if the port is not in the VLAN member set.
The DSA documentation Documentation/networking/switchdev.rst states:
When the bridge has VLAN filtering enabled and a PVID is not
configured on the ingress port, untagged and 802.1p tagged
packets must be dropped. When the bridge has VLAN filtering
enabled and a PVID exists on the ingress port, untagged and
priority-tagged packets must be accepted and forwarded according
to the bridge's port membership of the PVID VLAN. When the
bridge has VLAN filtering disabled, the presence/lack of a
PVID should not influence the packet forwarding decision.
To comply with this, we add two arrays of bool in the RTL8366RB
state that keeps track of if filtering and PVID is enabled or
not for each port. We then add code such that whenever filtering
or PVID changes, we update the filter according to the
specification.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hacky default VLAN setup was done in order to direct
packets to the right ports and provide port isolation, both
which we now support properly using custom tags and proper
bridge port isolation.
We can drop the custom VLAN code and leave all VLAN handling
alone, as users expect things to be. We can also drop
ds->configure_vlan_while_not_filtering = false; and let
the core deal with any VLANs it wants.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use port isolation registers to configure bridge offloading.
Tested on the D-Link DIR-685, switching between ports and
sniffing ports to make sure no packets leak.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same members of the Marvell Ethernet switches impose MTU restrictions
on ports used for connecting to the CPU or another switch for DSA. If
the MTU is set too low, tagged frames will be discarded. Ensure the
worst case tagger overhead is included in setting the MTU for DSA and
CPU ports.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU passed to the DSA driver is the payload size, typically 1500.
However, the switch uses the frame size when applying restrictions.
Adjust the MTU with the size of the Ethernet header and the frame
checksum. The VLAN header also needs to be included when the frame
size it per port, but not when it is global.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The datasheets suggests the 6161 uses a per port setting for jumbo
frames. Testing has however shown this is not correct, it uses the old
style chip wide MTU control. Change the ops in the 6161 structure to
reflect this.
Fixes: 1baf0fac10fb ("net: dsa: mv88e6xxx: Use chip-wide max frame size for MTU")
Reported by: 曹煜 <cao88yu@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since both forms are accepted, let's search for both when we
pre-validate the PHY modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/mptcp/protocol.c
977d293e23b4 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce01 ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the sja1105 driver is finally sane enough again to stop having
a ternary VLAN awareness state, we can remove priv->vlan_aware and query
DSA for the ds->vlan_filtering value (for SJA1105, VLAN filtering is a
global property).
Also drop the paranoid checking that DSA calls ->port_vlan_filtering
multiple times without the VLAN awareness state changing. It doesn't,
the same check is present inside dsa_port_vlan_filtering too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver only needs the reset GPIO for a very brief period, so instead
of using devres and keeping the descriptor pointer inside priv, just use
that descriptor inside the sja1105_hw_reset function and then let go of
it.
Also use gpiod_get_optional while at it, and error out on real errors
(bad flags etc).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
driver
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08ca ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b752 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like this field was never used since its introduction in commit
227d07a07ef1 ("net: dsa: sja1105: Add support for traffic through
standalone ports") remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, the Realtek drivers fall under category (b). To solve it,
we can register the MDIO bus under devres too, which restores the
previous behavior.
Fixes: ac3a68d56651 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When interfacing with a Broadcom PHY, request the auto-power down, DLL
disable and IDDQ-SR modes to be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
on error
Commit 86f8b1c01a0a ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.
Commit fb6ec87f7229 ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.
Commit 08156ba430b4 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.
When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:
devlink_port_unregister:
WARN_ON(!list_empty(&devlink_port->region_list));
So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.
Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.
But DSA's layering stays in our way quite badly here.
The options I've considered are:
1. Introduce a function in devlink to just change a port's type and
flavour. No dice, devlink keeps a lot of state, it really wants the
port to not be registered when you set its parameters, so changing
anything can only be done by destroying what we currently have and
recreating it.
2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
and the region returned, keep those in a list, then when the devlink
port unregister needs to take place, the existing devlink regions are
destroyed by DSA, and we replay the creation of new regions using the
cached parameters. Problem: mv88e6xxx keeps the region pointers in
chip->ports[port].region, and these will remain stale after DSA frees
them. There are many things DSA can do, but updating mv88e6xxx's
private pointers is not one of them.
3. Just let the driver do it (i.e. introduce a very specific method
called ds->ops->port_reinit_as_unused, which unregisters its devlink
port devlink regions, then the old devlink port, then registers the
new one, then the devlink port regions for it). While it does work,
as opposed to the others, it's pretty horrible from an API
perspective and we can do better.
4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
which in the case of mv88e6xxx must register and unregister the
devlink port regions. Call these 2 methods when the port must be
reinitialized as unused.
Naturally, I went for the 4th approach.
Fixes: 08156ba430b4 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
