| Age | Commit message (Collapse) | Author |
|---|
|
In sja1105_static_config_upload, in two cases memory is leaked: when
static_config_buf_prepare_for_upload fails and when sja1105_inhibit_tx
fails. In both cases config_buf should be released.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Fixes: 1a4c69406cc1 ("net: dsa: sja1105: Prevent PHY jabbering during switch reset")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Arnd Bergmann pointed out in commit 78fe8a28fb96 ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.
So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per the DT phy-mode specification, RGMII delays are applied by the
MAC when there is no PHY present on the link.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pad_mii_tx registers point to the same memory region but were
unused. So convert to using these for RGMII I/O cell configuration, as
they bear a shorter name.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used to stop egress traffic in .phylink_mac_link_up.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On TX, timestamping is performed synchronously from the
port_deferred_xmit worker thread.
In management routes, the switch is requested to take egress timestamps
(again partial), which are reconstructed and appended to a clone of the
skb that was just sent. The cloning is done by DSA and we retrieve the
pointer from the structure that DSA keeps in skb->cb.
Then these clones are enqueued to the socket's error queue for
application-level processing.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The design of this PHC driver is influenced by the switch's behavior
w.r.t. timestamping. It exposes two PTP counters, one free-running
(PTPTSCLK) and the other offset- and frequency-corrected in hardware
through PTPCLKVAL, PTPCLKADD and PTPCLKRATE. The MACs can sample either
of these for frame timestamps.
However, the user manual warns that taking timestamps based on the
corrected clock is less than useful, as the switch can deliver corrupted
timestamps in a variety of circumstances.
Therefore, this PHC uses the free-running PTPTSCLK together with a
timecounter/cyclecounter structure that translates it into a software
time domain. Thus, the settime/adjtime and adjfine callbacks are
hardware no-ops.
The timestamps (introduced in a further patch) will also be translated
to the correct time domain before being handed over to the userspace PTP
stack.
The introduction of a second set of PHC operations that operate on the
hardware PTPCLKVAL/PTPCLKADD/PTPCLKRATE in the future is somewhat
unavoidable, as the TTEthernet core uses the corrected PTP time domain.
However, the free-running counter + timecounter structure combination
will suffice for now, as the resulting timestamps yield a sub-50 ns
synchronization offset in steady state using linuxptp.
For this patch, in absence of frame timestamping, the operations of the
switch PHC were tested by syncing it to the system time as a local slave
clock with:
phc2sys -s CLOCK_REALTIME -c swp2 -O 0 -m -S 0.01
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are needed for the situation where the switch driver and the PTP
driver are both built as modules.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA callbacks were written with the E/T (first generation) in mind,
which is quite different.
For P/Q/R/S completely new implementations need to be provided, which
are held as function pointers in the priv->info structure. We are
taking a slightly roundabout way for this (a function from
sja1105_main.c reads a structure defined in sja1105_spi.c that
points to a function defined in sja1105_main.c), but it is what it is.
The FDB dump callback works for both families, hence no function pointer
for that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid. Currently it
is ignoring the returns from the function calls. Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.
Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
