| Age | Commit message (Collapse) | Author |
|---|
|
This prepares the driver for hardware bridging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Code used and needed in mv886xxx.c should be initialized there as well,
so factor it out from the individual initialization files.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable EEE support for MV88E6352.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some busy bits are available in the global register 1, such as the ATU
Busy bit. We may want to use this function to wait for them to change,
so add a new parameter to mv88e6352_wait() instead of hard-coding
REG_GLOBAL2.
In the meantime, since the REG_READ() macro already checks for error,
remove the redundant check for ret < 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Display sw_in_discards, sw_in_filtered, and sw_out_filtered for chips
supported by mv88e6123_61_65 and mv88e6352 drivers.
The variables are provided in port registers, not the normal status registers.
Mark by adding 0x100 to the register offset and add special handling code
to mv88e6xxx_get_ethtool_stats.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report switch register values to ethtool.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MV88E6352 supports read and write access to its configuration eeprom.
There is no means to detect if an EEPROM is connected to the switch.
Also, the switch supports EEPROMs with different sizes, but can not detect
or report the type or size of connected EEPROMs. Therefore, do not implement
the get_eeprom_len callback but depend on platform or devicetree data to
provide information about EEPROM presence and size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MV88E6352 supports reading the chip temperature from two PHY registers,
6:26 and 6:27. Report it using the more accurate register 6:27.
Also report temperature limit and alarm.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MV88E6176 is mostly compatible to MV88E6352 and is documented
in the same functional specification. Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 88E6352 is mostly compatible to MV88E6123/61/65,
but requires indirect phy access. Also, its configuration
registers are a bit different.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
