| Age | Commit message (Collapse) | Author |
|---|
|
Move static MAC table operations to separate functions in order to reuse
the code for add/del_fdb. This is needed to address kernel warnings
caused by the lack of fdb add function support in the current driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
FID is directly mapped to VID. However, configuring a MAC address with a
VID != 0 resulted in incorrect configuration due to an incorrect bit
mask. This kernel commit fixed the issue by correcting the bit mask and
ensuring proper configuration of MAC addresses with non-zero VID.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current regmap bulk access is broken, resulting to wrong reads/writes
if ksz_read64/ksz_write64 functions are used.
Mostly this issue was visible by using ksz8_fdb_dump(), which returned
corrupt MAC address.
The reason is that regmap was configured to have max_raw_read/write,
even if ksz8863_mdio_read/write functions are able to handle unlimited
read/write accesses. On ksz_read64 function we are using multiple 32bit
accesses by incrementing each access by 1 instead of 4. Resulting buffer
had 01234567.12345678 instead of 01234567.89abcdef.
We have multiple ways to fix it:
- enable 4 byte alignment for 32bit accesses. Since the HW do not have
this requirement. It will break driver.
- disable max_raw_* limit.
This patch is removing max_raw_* limit for regmap accesses in ksz8863_smi.
Fixes: 60a364760002 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
empty dynamic MAC table.
If the dynamic MAC table is empty, we will still extract one outdated
entry. Fix it by using correct bit offset.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are using wrong offset, so we will get not a timestamp.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current ksz8_fdb_dump() is able to extract only max 249 entries on
the ksz8863/ksz8873 series of switches. This happened due to wrong
bit mask and offset calculation.
This commit corrects the issue and allows for the complete extraction of
all 1024 entries.
Fixes: 4b20a07e103f ("net: dsa: microchip: ksz8795: add support for ksz88xx chips")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this patch, the ksz8_fdb_dump() function had several issues, such
as uninitialized variables and incorrect usage of source port as a bit
mask. These problems caused inaccurate reporting of vid information and
port assignment in the bridge fdb.
Fixes: e587be759e6e ("net: dsa: microchip: update fdb add/del/dump in ksz_common")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/wireless/nl80211.c
b27f07c50a73 ("wifi: nl80211: fix puncturing bitmap policy")
cbbaf2bb829b ("wifi: nl80211: add a command to enable/disable HW timestamping")
https://lore.kernel.org/all/20230314105421.3608efae@canb.auug.org.au
tools/testing/selftests/net/Makefile
62199e3f1658 ("selftests: net: Add VXLAN MDB test")
13715acf8ab5 ("selftest: Add test for bind() conflicts.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The blamed commit has replaced a ksz_write8() call to address
REG_PORT_5_CTRL_6 (0x56) with a ksz_set_xmii() -> ksz_pwrite8() call to
regs[P_XMII_CTRL_1], which is also defined as 0x56 for ksz8795_regs[].
The trouble is that, when compared to ksz_write8(), ksz_pwrite8() also
adjusts the register offset with the port base address. So in reality,
ksz_pwrite8(offset=0x56) accesses register 0x56 + 0x50 = 0xa6, which in
this switch appears to be unmapped, and the RGMII delay configuration on
the CPU port does nothing.
So if the switch wasn't fine with the RGMII delay configuration done
through pin strapping and relied on Linux to apply a different one in
order to pass traffic, this is now broken.
Using the offset translation logic imposed by ksz_pwrite8(), the correct
value for regs[P_XMII_CTRL_1] should have been 0x6 on ksz8795_regs[], in
order to really end up accessing register 0x56.
Static code analysis shows that, despite there being multiple other
accesses to regs[P_XMII_CTRL_1] in this driver, the only code path that
is applicable to ksz8795_regs[] and ksz8_dev_ops is ksz_set_xmii().
Therefore, the problem is isolated to RGMII delays.
In its current form, ksz8795_regs[] contains the same value for
P_XMII_CTRL_0 and for P_XMII_CTRL_1, and this raises valid suspicions
that writes made by the driver to regs[P_XMII_CTRL_0] might overwrite
writes made to regs[P_XMII_CTRL_1] or vice versa.
Again, static analysis shows that the only accesses to P_XMII_CTRL_0
from the driver are made from code paths which are not reachable with
ksz8_dev_ops. So the accesses made by ksz_set_xmii() are safe for this
switch family.
[ vladimiroltean: rewrote commit message ]
Fixes: c476bede4b0f ("net: dsa: microchip: ksz8795: use common xmii function")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230315231916.2998480-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
drivers/net/dsa/microchip/ksz9477_i2c.c:84:34: error: ‘ksz9477_dt_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ETS Qdisc support for KSZ9477 of switches. Current implementation is
limited to strict priority mode.
Tested on KSZ8563R with following configuration:
tc qdisc replace dev lan2 root handle 1: ets strict 4 \
priomap 3 3 2 2 1 1 0 0
ip link add link lan2 name v1 type vlan id 1 \
egress-qos-map 0:0 1:1 2:2 3:3 4:4 5:5 6:6 7:7
and patched iperf3 version:
https://github.com/esnet/iperf/pull/1476
iperf3 -c 172.17.0.1 -b100M -l1472 -t100 -u -R --sock-prio 2
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ksz_setup_tc_mode() to make queue scheduling and shaping
configuration more visible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.
Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full. Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.
EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When NET_DSA_MICROCHIP_KSZ_COMMON is built-in but PTP is a loadable
module, the ksz_ptp support still causes a link failure:
ld.lld-16: error: undefined symbol: ptp_clock_index
>>> referenced by ksz_ptp.c
>>> drivers/net/dsa/microchip/ksz_ptp.o:(ksz_get_ts_info) in archive vmlinux.a
This can happen if NET_DSA_MICROCHIP_KSZ8863_SMI is enabled, or
even if none of the KSZ9477_I2C/KSZ_SPI/KSZ8863_SMI ones are active
but only the common module is.
The most straightforward way to address this is to move the
dependency to NET_DSA_MICROCHIP_KSZ_PTP itself, which can now
only be enabled if both PTP_1588_CLOCK support is reachable
from NET_DSA_MICROCHIP_KSZ_COMMON. Alternatively, one could make
NET_DSA_MICROCHIP_KSZ_COMMON a hidden Kconfig symbol and extend the
PTP_1588_CLOCK_OPTIONAL dependency to NET_DSA_MICROCHIP_KSZ8863_SMI as
well, but that is a little more fragile.
Fixes: eac1ea20261e ("net: dsa: microchip: ptp: add the posix clock support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230130131808.1084796-1-arnd@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Conflicts:
drivers/net/ethernet/intel/ice/ice_main.c
418e53401e47 ("ice: move devlink port creation/deletion")
643ef23bd9dd ("ice: Introduce local var for readability")
https://lore.kernel.org/all/20230127124025.0dacef40@canb.auug.org.au/
https://lore.kernel.org/all/20230124005714.3996270-1-anthony.l.nguyen@intel.com/
drivers/net/ethernet/engleder/tsnep_main.c
3d53aaef4332 ("tsnep: Fix TX queue stop/wake for multiple queues")
25faa6a4c5ca ("tsnep: Replace TX spin_lock with __netif_tx_lock")
https://lore.kernel.org/all/20230127123604.36bb3e99@canb.auug.org.au/
net/netfilter/nf_conntrack_proto_sctp.c
13bd9b31a969 ("Revert "netfilter: conntrack: add sctp DATA_SENT state"")
a44b7651489f ("netfilter: conntrack: unify established states for SCTP paths")
f71cb8f45d09 ("netfilter: conntrack: sctp: use nf log infrastructure for invalid packets")
https://lore.kernel.org/all/20230127125052.674281f9@canb.auug.org.au/
https://lore.kernel.org/all/d36076f3-6add-a442-6d4b-ead9f7ffff86@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with commit eee16b147121 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b44908095612 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b44908095612 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip").
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MDIO core should not pass a C45 request via the C22 API call any
more. So remove the tests from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ipa/ipa_interrupt.c
drivers/net/ipa/ipa_interrupt.h
9ec9b2a30853 ("net: ipa: disable ipa interrupt during suspend")
8e461e1f092b ("net: ipa: introduce ipa_interrupt_enable()")
d50ed3558719 ("net: ipa: enable IPA interrupt handlers separate from registration")
https://lore.kernel.org/all/20230119114125.5182c7ab@canb.auug.org.au/
https://lore.kernel.org/all/79e46152-8043-a512-79d9-c3b905462774@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to return negative error codes here but the copy_to/from_user()
functions return the number of bytes remaining to be copied.
Fixes: c59e12a140fb ("net: dsa: microchip: ptp: Initial hardware time stamping support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/Y8fJxSvbl7UNVHh/@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230118174735.702377-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is difference in implementation of per_out pins between KSZ9563
and LAN937x. In KSZ9563, Timestamping control register (0x052C) bit 6,
if 1 - timestamp input and 0 - trigger output. But it is opposite for
LAN937x 1 - trigger output and 0 - timestamp input.
As per per_out gpio pins, KSZ9563 has four Led pins and two dedicated
gpio pins. But in LAN937x dedicated gpio pins are removed instead there
are up to 10 LED pins out of which LED_0 and LED_1 can be mapped to PTP
tou 0, 1 or 2. This patch sets the bit 6 in 0x052C register and
configure the LED override and source register for LAN937x series of
switches alone.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LAN937x series of switches support 2 step timestamping mechanism. There
are timestamp correction calculation performed in ksz_rcv_timestamp and
ksz_xmit_timestamp which are applicable only for p2p1step. To check
whether the 2 step is enabled or not in tag_ksz.c introduced the helper
function in taggger_data to query it from ksz_ptp.c. Based on whether 2
step is enabled or not, timestamp calculation are performed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two programmable pins available for Trigger output unit to
generate periodic pulses. This patch add verify_pin for the available 2
pins and configure it with respect to GPIO index for the TOU unit.
Tested using testptp
./testptp -i 0 -L 0,2
./testptp -i 0 -d /dev/ptp0 -p 1000000000
./testptp -i 1 -L 1,2
./testptp -i 1 -d /dev/ptp0 -p 100000000
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LAN937x and KSZ PTP supported switches has Three Trigger output unit.
This TOU can used to generate the periodic signal for PTP. TOU has the
cycle width register of 32 bit in size and period width register of 24
bit, each value is of 8ns so the pulse width can be maximum 125ms.
Tested using ./testptp -d /dev/ptp0 -p 1000000000 -w 100000000 for
generating the 10ms pulse width
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For PDelay_Resp messages we will likely have a negative value in the
correction field. The switch hardware cannot correctly update such
values (produces an off by one error in the UDP checksum), so it must be
moved to the time stamp field in the tail tag. Format of the correction
field is 48 bit ns + 16 bit fractional ns. After updating the
correction field, clone is no longer required hence it is freed.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the routines for transmission of ptp packets. When the
ptp pdelay_req packet to be transmitted, it uses the deferred xmit
worker to schedule the packets.
During irq_setup, interrupt for Sync, Pdelay_req and Pdelay_rsp are
enabled. So interrupt is triggered for all three packets. But for
p2p1step, we require only time stamp of Pdelay_req packet. Hence to
avoid posting of the completion from ISR routine for Sync and
Pdelay_resp packets, ts_en flag is introduced. This controls which
packets need to processed for timestamp.
After the packet is transmitted, ISR is triggered. The time at which
packet transmitted is recorded to separate register.
This value is reconstructed to absolute time and posted to the user
application through socket error queue.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx Timestamping is done through 4 additional bytes in tail tag.
Whenever the ptp packet is received, the 4 byte hardware time stamped
value is added before 1 byte tail tag. Also, bit 7 in tail tag indicates
it as PTP frame. This 4 byte value is extracted from the tail tag and
reconstructed to absolute time and assigned to skb hwtstamp.
If the packet received in PDelay_Resp, then partial ingress timestamp
is subtracted from the correction field. Since user space tools expects
to be done in hardware.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PTP Interrupt mask and status register differ from the global and port
interrupt mechanism by two methods. One is that for global/port
interrupt enabling we have to clear the bit but for ptp interrupt we
have to set the bit. And other is bit12:0 is reserved in ptp interrupt
registers. This forced to not use the generic implementation of
global/port interrupt method routine. This patch implement the ptp
interrupt mechanism to read the timestamp register for sync, pdelay_req
and pdelay_resp.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is used for reconstructing the absolute time from the 32bit
hardware time stamping value. The do_aux ioctl is used for reading the
ptp hardware clock and store it to global variable.
The timestamped value in tail tag during rx and register during tx are
32 bit value (2 bit seconds and 30 bit nanoseconds). The time taken to
read entire ptp clock will be time consuming. In order to speed up, the
software clock is maintained. This clock time will be added to 32 bit
timestamp to get the absolute time stamp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PTP is enabled in hardware bit 6 of PTP_MSG_CONF1 register, the
transmit frame needs additional 4 bytes before the tail tag. It is
needed for all the transmission packets irrespective of PTP packets or
not.
The 4-byte timestamp field is 0 for frames other than Pdelay_Resp. For
the one-step Pdelay_Resp, the switch needs the receive timestamp of the
Pdelay_Req message so that it can put the turnaround time in the
correction field.
Since PTP has to be enabled for both Transmission and reception
timestamping, driver needs to track of the tx and rx setting of the all
the user ports in the switch.
Two flags hw_tx_en and hw_rx_en are added in ksz_port to track the
timestampping setting of each port. When any one of ports has tx or rx
timestampping enabled, bit 6 of PTP_MSG_CONF1 is set and it is indicated
to tag_ksz.c through tagger bytes. This flag adds 4 additional bytes to
the tail tag. When tx and rx timestamping of all the ports are disabled,
then 4 bytes are not added.
Tested using hwstamp -i <interface>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the routine for get_ts_info, hwstamp_get, set. This enables
the PTP support towards userspace applications such as linuxptp.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Co-developed-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com> # mostly api
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ swithes used interrupts for detecting the phy link up and down.
During registering the interrupt handler, it used IRQF_TRIGGER_FALLING
flag. But this flag has to be retrieved from device tree instead of hard
coding in the driver, so removing the flag.
Fixes: ff319a644829 ("net: dsa: microchip: move interrupt handling logic from lan937x to ksz_common")
Reported-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20221213101440.24667-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add stats64 support for ksz8xxx series of switches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20221205052904.2834962-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To make the code more comparable to KSZ9477 code, move DSA
configurations to the same location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
compatible switches
KSZ8795 and KSZ9477 compatible series of switches use global max frame
size configuration register. So, enable MTU normalization for this reason.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make MTU configurable on KSZ87xx and KSZ88xx series of switches.
Before this patch, pre-configured behavior was different on different
switch series, due to opposite meaning of the same bit:
- KSZ87xx: Reg 4, Bit 1 - if 1, max frame size is 1532; if 0 - 1514
- KSZ88xx: Reg 4, Bit 1 - if 1, max frame size is 1514; if 0 - 1532
Since the code was telling "... SW_LEGAL_PACKET_DISABLE, true)", I
assume, the idea was to set max frame size to 1532.
With this patch, by setting MTU size 1500, both switch series will be
configured to the 1532 frame limit.
This patch was tested on KSZ8873.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add ksz_rmw8(), it will be used in the next patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If we have global MTU configuration, it is enough to configure it on CPU
port only.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are no HW specific registers, so we can process all of them
in one location.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Arun Ramadoss <arun.ramadoss@microchip.com> (KSZ9893 and LAN937x)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.
Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Probe functions uses normal dev_err() to check error conditions
and print messages. Replace dev_err() with dev_err_probe() to
have more standardized format and error logging.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8563 have three port interrupts: PTP, PHY and ACL. Add
port_nirq as 3 for KSZ8563 inside ksz_chip_data.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add status validation for port register write inside
lan937x_change_mtu. ksz_pwrite and ksz_pread api's are
updated with return type int (Reference patch mentioned
below). Update lan937x_change_mtu with status validation
for ksz_pwrite16().
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220826105634.3855578-6-o.rempel@pengutronix.de/
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add device irq in i2c probe function.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compatible string
Add KSZ9563 inside ksz_switch_chips structure with
port_nirq as 3. KSZ9563 use KSZ9893 switch parameters
but port_nirq count is 3 for KSZ9563 whereas 2 for
KSZ9893. Add KSZ9563 inside ksz_switch_chips as a separate
member and from device tree map compatible string into
KSZ9563 inside ksz_spi.c and ksz9477_i2c.c.
Global Chip ID 1 and 2 registers read value 9893, select
sku based on Global Chip ID 4 Register which read 0x1c
for KSZ9563.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
