| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 692eb9f8a5b71d852e873375d20cf5da7a046ea6 ]
When Linux sends out untagged traffic from a port, it will enter the CPU
port without any VLAN tag, even if the port is a member of a vlan
filtering bridge with a PVID egress untagged VLAN.
This makes the CPU port's PVID take effect, and the PVID's VLAN
table entry controls if the packet will be tagged on egress.
Since commit 45e9d59d3950 ("net: dsa: b53: do not allow to configure
VLAN 0") we remove bridged ports from VLAN 0 when joining or leaving a
VLAN aware bridge. But we also clear the untagged bit, causing untagged
traffic from the controller to become tagged with VID 0 (and priority
0).
Fix this by not touching the untagged map of VLAN 0. Additionally,
always keep the CPU port as a member, as the untag map is only effective
as long as there is at least one member, and we would remove it when
bridging all ports and leaving no standalone ports.
Since Linux (and the switch) treats VLAN 0 tagged traffic like untagged,
the actual impact of this is rather low, but this also prevented earlier
detection of the issue.
Fixes: 45e9d59d3950 ("net: dsa: b53: do not allow to configure VLAN 0")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250602194914.1011890-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit bc1a65eb81a21e2aa3c3dca058ee8adf687b6ef5 ]
According to OpenMDK, bit 2 of the RGMII register has a different
meaning for BCM53115 [1]:
"DLL_IQQD 1: In the IDDQ mode, power is down0: Normal function
mode"
Configuring RGMII delay works without setting this bit, so let's keep it
at the default. For other chips, we always set it, so not clearing it
is not an issue.
One would assume BCM53118 works the same, but OpenMDK is not quite sure
what this bit actually means [2]:
"BYPASS_IMP_2NS_DEL #1: In the IDDQ mode, power is down#0: Normal
function mode1: Bypass dll65_2ns_del IP0: Use
dll65_2ns_del IP"
So lets keep setting it for now.
[1] https://github.com/Broadcom-Network-Switching-Software/OpenMDK/blob/master/cdk/PKG/chip/bcm53115/bcm53115_a0_defs.h#L19871
[2] https://github.com/Broadcom-Network-Switching-Software/OpenMDK/blob/master/cdk/PKG/chip/bcm53118/bcm53118_a0_defs.h#L14392
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-6-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5ea0d42c1980e6d10e5cb56a78021db5bfcebaaf ]
Add RGMII to supported interfaces for BCM63xx RGMII ports so they can be
actually used in RGMII mode.
Without this, phylink will fail to configure them:
[ 3.580000] b53-switch 10700000.switch GbE3 (uninitialized): validation of rgmii with support 0000000,00000000,00000000,000062ff and advertisement 0000000,00000000,00000000,000062ff failed: -EINVAL
[ 3.600000] b53-switch 10700000.switch GbE3 (uninitialized): failed to connect to PHY: -EINVAL
[ 3.610000] b53-switch 10700000.switch GbE3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Fixes: ce3bf94871f7 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-5-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4af523551d876ab8b8057d1e5303a860fd736fcb ]
bcm63xx's RGMII ports are always in MAC mode, never in PHY mode, so we
shouldn't enable any delays and let the PHY handle any delays as
necessary.
This fixes using RGMII ports with normal PHYs like BCM54612E, which will
handle the delay in the PHY.
Fixes: ce3bf94871f7 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250602193953.1010487-3-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4227ea91e2657f7965e34313448e9d0a2b67712e ]
When bridged ports and standalone ports share a VLAN, e.g. via VLAN
uppers, or untagged traffic with a vlan unaware bridge, the ASIC will
still try to forward traffic to known FDB entries on standalone ports.
But since the port VLAN masks prevent forwarding to bridged ports, this
traffic will be dropped.
This e.g. can be observed in the bridge_vlan_unaware ping tests, where
this breaks pinging with learning on.
Work around this by enabling the simplified EAP mode on switches
supporting it for standalone ports, which causes the ASIC to redirect
traffic of unknown source MAC addresses to the CPU port.
Since standalone ports do not learn, there are no known source MAC
addresses, so effectively this redirects all incoming traffic to the CPU
port.
Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250508091424.26870-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2e7179c628d3cb9aee75e412473813b099e11ed4 ]
When a port gets set up, b53 disables learning and enables the port for
flooding. This can undo any bridge configuration on the port.
E.g. the following flow would disable learning on a port:
$ ip link add br0 type bridge
$ ip link set sw1p1 master br0 <- enables learning for sw1p1
$ ip link set br0 up
$ ip link set sw1p1 up <- disables learning again
Fix this by populating dsa_switch_ops::port_setup(), and set up initial
config there.
Fixes: f9b3827ee66c ("net: dsa: b53: Support setting learning on port")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-12-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9f34ad89bcf0e6df6f8b01f1bdab211493fc66d1 ]
When VLAN filtering is off, we configure the switch to forward, but not
learn on VLAN table misses. This effectively disables learning while not
filtering.
Fix this by switching to forward and learn. Setting the learning disable
register will still control whether learning actually happens.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-11-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2dc2bd57111582895e10f54ea380329c89873f1c ]
To allow runtime switching between vlan aware and vlan non-aware mode,
we need to properly keep track of any bridge VLAN configuration.
Likewise, we need to know when we actually switch between both modes, to
not have to rewrite the full VLAN table every time we update the VLANs.
So keep track of the current vlan_filtering mode, and on changes, apply
the appropriate VLAN configuration.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-10-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f089652b6b16452535dcc5cbaa6e2bb05acd3f93 ]
Documentation/networking/switchdev.rst says:
- with VLAN filtering turned off: the bridge is strictly VLAN unaware and its
data path will process all Ethernet frames as if they are VLAN-untagged.
The bridge VLAN database can still be modified, but the modifications should
have no effect while VLAN filtering is turned off.
This breaks if we immediately apply the VLAN configuration, so skip
writing it when vlan_filtering is off.
Fixes: 0ee2af4ebbe3 ("net: dsa: set configure_vlan_while_not_filtering to true by default")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 45e9d59d39503bb3e6ab4d258caea4ba6496e2dc ]
Since we cannot set forwarding destinations per VLAN, we should not have
a VLAN 0 configured, as it would allow untagged traffic to work across
ports on VLAN aware bridges regardless if a PVID untagged VLAN exists.
So remove the VLAN 0 on join, an re-add it on leave. But only do so if
we have a VLAN aware bridge, as without it, untagged traffic would
become tagged with VID 0 on a VLAN unaware bridge.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 13b152ae40495966501697693f048f47430c50fd ]
While JOIN_ALL_VLAN allows to join all VLANs, we still need to keep the
default VLAN enabled so that untagged traffic stays untagged.
So rejoin the default VLAN even for switches with JOIN_ALL_VLAN support.
Fixes: 48aea33a77ab ("net: dsa: b53: Add JOIN_ALL_VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1c1901c5cc881425cc45992ab6c5418174e9e5a ]
The untagged default VLAN is added to the default vlan, which may be
one, but we modify the VLAN 0 entry on bridge leave.
Fix this to use the correct VLAN entry for the default pvid.
Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 083c6b28c0cbcd83b6af1a10f2c82937129b3438 ]
Presumably the intention here was to flush the VLAN of the old pvid, not
the added VLAN again, which we already flushed before.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f480851981043d9bb6447ca9883ade9247b9a0ad ]
Currently the PVID of ports are only set when adding/updating VLANs with
PVID set or removing VLANs, but not when clearing the PVID flag of a
VLAN.
E.g. the following flow
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master bridge
$ bridge vlan add dev sw1p1 vid 10 pvid untagged
$ bridge vlan add dev sw1p1 vid 10 untagged
Would keep the PVID set as 10, despite the flag being cleared. Fix this
by checking if we need to unset the PVID on vlan updates.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 425f11d4cc9bd9e97e6825d9abb2c51a068ca7b5 ]
The Broadcom management header does not carry the original VLAN tag
state information, just the ingress port, so for untagged frames we do
not know from which VLAN they originated.
Therefore keep the CPU port always tagged except for VLAN 0.
Fixes the following setup:
$ ip link add br0 type bridge vlan_filtering 1
$ ip link set sw1p1 master br0
$ bridge vlan add dev br0 pvid untagged self
$ ip link add sw1p2.10 link sw1p2 type vlan id 10
Where VID 10 would stay untagged on the CPU port.
Fixes: 2c32a3d3c233 ("net: dsa: b53: Do not force CPU to be always tagged")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f93185a757ff38b36f849c659aeef368db15a68 ]
Allow reserved multicast to ignore VLAN membership so STP and other
management protocols work without a PVID VLAN configured when using a
vlan aware bridge.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250429201710.330937-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 36355ddfe8955f226a88a543ed354b9f6b84cd70 ]
For STP to work, receiving BPDUs is essential, but the appropriate bit
was never set. Without GC_RX_BPDU_EN, the switch chip will filter all
BPDUs, even if an appropriate PVID VLAN was setup.
Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250414200434.194422-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
All modern chips support and need the 10_100 bit set for supporting jumbo
frames on 10/100 ports, so instead of enabling it only for 583XX enable
it for everything except bcm63xx, where the bit is writeable, but does
nothing.
Tested on BCM53115, where jumbo frames were dropped at 10/100 speeds
without the bit set.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While BCM5325/5365 do not support jumbo frames, they do support slightly
oversized frames, so do not error out if requesting a supported MTU for
them.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
BCM5325/BCM5365 do not support jumbo frames, so we should not report a
jumbo frame mtu for them. But they do support so called "oversized"
frames up to 1536 bytes long by default, so report an appropriate MTU.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
|
|
Rather than print an error even when we get -EPROBE_DEFER, use
dev_err_probe() to filter out those messages.
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240820004436.224603-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Broadcom switches supported by the b53 driver use a chip-wide jumbo frame
configuration. In the commit referenced with the Fixes tag, the setting
is applied just for the last port changing its MTU.
While configuring CPU ports accounts for tagger overhead, user ports do
not. When setting the MTU for a user port, the chip-wide setting is
reduced to not include the tagger overhead, resulting in an potentially
insufficient chip-wide maximum frame size for the CPU port.
As, by design, the CPU port MTU is adjusted for any user port change,
apply the chip-wide setting only for CPU ports. This aligns the driver
to the behavior of other switch drivers.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Martin Willi <martin@strongswan.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert b53 to provide its own phylink MAC operations, thus avoiding the
shim layer in DSA's port.c
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-9-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Only use the PHYLINK implementation from there on now that an equivalent
configuration is applied to all of the switch ports.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-8-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
And make sure this is done for the MLO_AN_PHY case, where it actually
makes sense, contrary to b53_adjust_link() which only did it for
fixed-PHY configurations where it does not make sense.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-7-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Call b53_adjust_531x5_rgmii() and b53_adjust_5325_mii() from
b53_phylink_mac_config() when we have a fixed PHY in preparation for removing
b53_adjust_link(). Also move b53_adjust_63xx_rgmii() to
b53_phylink_mac_config() where it logically belongs.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-6-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Just like what b53_adjust_link() does, force flow control for the
BCM5301X CPU port(s) by forcing rx_pause and tx_pause in
b53_phylink_mac_link_up(). Preparatory step for getting rid of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-5-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Takes care of doing the 5325 switch series specific MII programming and
is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-4-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Takes care of doing the 531x5 switch series specific RGMII programming
and is called from b53_adjust_link() to allow the future removal of
b53_adjust_link().
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-3-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
They are not used outside of the b53_common.c file, no need to be
exported.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240423183339.1368511-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit f86ad77faf24 ("net: dsa: bcm_sf2: Utilize b53_{enable,
disable}_port"), bcm_sf2.c no longer calls b53_eee_enable_set(), and all
its callers are in b53_common.c.
We also need to move it, because it is called within b53_common.c before
its definition, and we want to avoid forward declarations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240206112527.4132299-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
b53_get_mac_eee() sets both eee_enabled and eee_active, and then
returns zero.
dsa_slave_get_eee(), which calls this function, will then continue to
call phylink_ethtool_get_eee(), which will return -EOPNOTSUPP if there
is no PHY present, otherwise calling phy_ethtool_get_eee() which in
turn will call genphy_c45_ethtool_get_eee().
genphy_c45_ethtool_get_eee() will overwrite eee_enabled and eee_active
with its own interpretation from the PHYs settings and negotiation
result.
Thus, when there is no PHY, dsa_slave_get_eee() will fail with
-EOPNOTSUPP, meaning eee_enabled and eee_active will not be returned to
userspace. When there is a PHY, eee_enabled and eee_active will be
overwritten by phylib, making the setting of these members in
b53_get_mac_eee() entirely unnecessary.
Remove this code, thus simplifying b53_get_mac_eee().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/E1rWbNI-002cCz-4x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
side
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: FLorian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230823085632.116725-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e53 ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e2d ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the BCM53134 Ethernet switch in the existing b53 dsa driver.
BCM53134 is very similar to the BCM58XX series.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
6e9d51b1a5cb ("net/mlx5e: Initialize link speed to zero")
1bffcea42926 ("net/mlx5e: Add devlink hairpin queues parameters")
https://lore.kernel.org/all/20230324120623.4ebbc66f@canb.auug.org.au/
https://lore.kernel.org/all/20230321211135.47711-1-saeed@kernel.org/
Adjacent changes:
drivers/net/phy/phy.c
323fe43cf9ae ("net: phy: Improved PHY error reporting in state machine")
4203d84032e2 ("net: phy: Ensure state transitions are processed from phy_stop()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM63268 requires special RGMII configuration to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM6318 and BCM63268 SoCs require a special handling for their RGMIIs, so we
should be able to identify them as a special BCM63xx switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM6318, BCM6362 and BCM63268 are SoCs with a B53 MMAP switch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM63xx RGMII ports require additional configuration in order to work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230319220805.124024-1-noltari@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
