| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit 24436be590c6fbb05f6161b0dfba7d9da60214aa ]
This patch tries to works around erratum DS80000789E 6 of the
mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old, already processed CAN frames or new, incompletely written CAN
frames to be (re-)processed.
To work around this issue, keep a per FIFO timestamp [1] of the last
valid received CAN frame and compare against the timestamp of every
received CAN frame. If an old CAN frame is detected, abort the
iteration and mark the number of valid CAN frames as processed in the
chip by incrementing the FIFO's tail index.
Further tests showed that this workaround can recognize old CAN
frames, but a small time window remains in which partially written CAN
frames [2] are not recognized but then processed. These CAN frames
have the correct data and time stamps, but the DLC has not yet been
updated.
[1] As the raw timestamp overflows every 107 seconds (at the usual
clock rate of 40 MHz) convert it to nanoseconds with the
timecounter framework and use this to detect stale CAN frames.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com [2]
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e793c724b48ca8cae9693bc3be528e85284c126a ]
The mcp251xfd chip is configured to provide a timestamp with each
received and transmitted CAN frame. The timestamp is derived from the
internal free-running timer, which can also be read from the TBC
register via SPI. The timer is 32 bits wide and is clocked by the
external oscillator (typically 20 or 40 MHz).
To avoid confusion, we call this timestamp "timestamp_raw" or "ts_raw"
for short.
Using the timecounter framework, the "ts_raw" is converted to 64 bit
nanoseconds since the epoch. This is what we call "timestamp".
This is a preparation for the next patches which use the "timestamp"
to work around a bug where so far only the "ts_raw" is used.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 85505e585637a737e4713c1386c30e37c325b82e ]
This is a preparatory patch to work around erratum DS80000789E 6 of
the mcp2518fd, the other variants of the chip family (mcp2517fd and
mcp251863) are probably also affected.
When handling the RX interrupt, the driver iterates over all pending
FIFOs (which are implemented as ring buffers in hardware) and reads
the FIFO header index from the RX FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN frames that were already processed, or new, incompletely
written CAN frames to be (re-)processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_rx_ring_update() with mcp251xfd_get_rx_len().
The mcp251xfd_handle_rxif_ring() function reads the received CAN
frames from the chip, iterates over them and pushes them into the
network stack. Prepare that the iteration can be stopped if an old CAN
frame is detected. The actual code to detect old or incomplete frames
and abort will be added in the next patch.
Link: https://lore.kernel.org/all/BL3PR11MB64844C1C95CA3BDADAE4D8CCFBC99@BL3PR11MB6484.namprd11.prod.outlook.com
Reported-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Closes: https://lore.kernel.org/all/FR0P281MB1966273C216630B120ABB6E197E89@FR0P281MB1966.DEUP281.PROD.OUTLOOK.COM
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
function
[ Upstream commit d49184b7b585f9da7ee546b744525f62117019f6 ]
This is a preparation patch.
Sending the UINC messages followed by incrementing the tail pointer
will be called in more than one place in upcoming patches, so factor
this out into a separate function.
Also make mcp251xfd_handle_rxif_ring_uinc() safe to be called with a
"len" of 0.
Tested-by: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Tested-by: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dd885d90c047dbdd2773c1d33954cbd8747d81e2 ]
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240830153113.2081440-1-martin.jocic@kvaser.com
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 48f827d4f48f5243e37b9240029ce3f456d1f490 ]
A new interrupt is triggered by resetting the DMA RX buffers.
Since MSI interrupts are faster than legacy interrupts, the reset
of the DMA buffers must be moved to the very end of the ISR,
otherwise a new MSI interrupt will be masked by the current one.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240620181320.235465-2-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c047 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cbf88a6ba7bb6ce0d3131b119298f73bd7b18459 ]
Rename the variable name board_irq in the ISR to pci_irq to
be more specific and to match the macro by which it is read.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-7-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c047 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11d186697ceb10b68c6a1fd505635346b1ccd055 ]
The code speaks for itself.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-4-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c047 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac765219c2c4e44f29063724c8d36435a3e61985 ]
This check is already done at the creation of the net devices in
kvaser_pciefd_setup_can_ctrls called from kvaser_pciefd_probe.
If it fails, the driver won't load, so there should be no need to
repeat the check inside the ISR. The number of channels is read
from the FPGA and should be trusted.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://lore.kernel.org/all/20240614151524.2718287-3-martin.jocic@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: dd885d90c047 ("can: kvaser_pciefd: Use a single write when releasing RX buffers")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50ea5449c56310d2d31c28ba91a59232116d3c1e ]
If the ring (rx, tx) and/or coalescing parameters (rx-frames-irq,
tx-frames-irq) have been configured while the interface was in CAN-CC
mode, but the interface is brought up in CAN-FD mode, the ring
parameters might be too big.
Use the default CAN-FD values in this case.
Fixes: 9263c2e92be9 ("can: mcp251xfd: ring: add support for runtime configurable RX/TX ring parameters")
Link: https://lore.kernel.org/all/20240805-mcp251xfd-fix-ringconfig-v1-1-72086f0ca5ee@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 06d4ef3056a7ac31be331281bb7a6302ef5a7f8a ]
It appears that the irq requested in m_can_open() may be leaked
if an error subsequently occurs: if m_can_start() fails.
Address this by calling free_irq in the unwind path for
such cases.
Flagged by Smatch.
Compile tested only.
Fixes: eaacfeaca7ad ("can: m_can: Call the RAM init directly from m_can_chip_config")
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240805-mcan-irq-v2-1-7154c0484819@kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 7dd9c26bd6cf679bcfdef01a8659791aa6487a29 upstream.
The mcp251x_hw_wake() function is called with the mpc_lock mutex held and
disables the interrupt handler so that no interrupts can be processed while
waking the device. If an interrupt has already occurred then waiting for
the interrupt handler to complete will deadlock because it will be trying
to acquire the same mutex.
CPU0 CPU1
---- ----
mcp251x_open()
mutex_lock(&priv->mcp_lock)
request_threaded_irq()
<interrupt>
mcp251x_can_ist()
mutex_lock(&priv->mcp_lock)
mcp251x_hw_wake()
disable_irq() <-- deadlock
Use disable_irq_nosync() instead because the interrupt handler does
everything while holding the mutex so it doesn't matter if it's still
running.
Fixes: 8ce8c0abcba3 ("can: mcp251x: only reset hardware as required")
Signed-off-by: Simon Arlott <simon@octiron.net>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/4fc08687-1d80-43fe-9f0d-8ef8475e75f6@0882a8b5-c6c3-11e9-b005-00805fc181fe.uuid.home.arpa
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3a0a88fcbaf9e027ecca3fe8775be9700b4d6460 ]
This patch updates the workaround for a problem similar to erratum
DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
In the bad case, the driver reads a too large head index. As the FIFO
is implemented as a ring buffer, this results in re-handling old CAN
transmit complete events.
Every transmit complete event contains with a sequence number that
equals to the sequence number of the corresponding TX request. This
way old TX complete events can be detected.
If the original driver detects a non matching sequence number, it
prints an info message and tries again later. As wrong sequence
numbers can be explained by the erratum DS80000789E 6, demote the info
message to debug level, streamline the code and update the comments.
Keep the behavior: If an old CAN TX complete event is detected, abort
the iteration and mark the number of valid CAN TX complete events as
processed in the chip by incrementing the FIFO's tail index.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8e0ddd36ce9536ad7478dd27df06c9ae92370ba ]
This is a preparatory patch to work around a problem similar to
erratum DS80000789E 6 of the mcp2518fd, the other variants of the chip
family (mcp2517fd and mcp251863) are probably also affected.
Erratum DS80000789E 6 says "reading of the FIFOCI bits in the FIFOSTA
register for an RX FIFO may be corrupted". However observation shows
that this problem is not limited to RX FIFOs but also effects the TEF
FIFO.
When handling the TEF interrupt, the driver reads the FIFO header
index from the TEF FIFO STA register of the chip.
In the bad case, the driver reads a too large head index. In the
original code, the driver always trusted the read value, which caused
old CAN transmit complete events that were already processed to be
re-processed.
Instead of reading and trusting the head index, read the head index
and calculate the number of CAN frames that were supposedly received -
replace mcp251xfd_tef_ring_update() with mcp251xfd_get_tef_len().
The mcp251xfd_handle_tefif() function reads the CAN transmit complete
events from the chip, iterates over them and pushes them into the
network stack. The original driver already contains code to detect old
CAN transmit complete events, that will be updated in the next patch.
Cc: Stefan Althöfer <Stefan.Althoefer@janztec.com>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d34d8163fd87978a6abd792e2d8ad849f4c3d57 ]
As the potential failure of usb_submit_urb(), it should be better to
return the err variable to catch the error.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Link: https://lore.kernel.org/all/20240521041020.1519416-1-nichen@iscas.ac.cn
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 19d5b2698c35b2132a355c67b4d429053804f8cc upstream.
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20240628194529.312968-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d8fb63e46c884c898a38f061c2330f7729e75510 upstream.
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Link: https://lore.kernel.org/all/20240517134355.770777-1-ivitro@gmail.com
[mkl: use more imperative wording in patch description]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a163c5761019b94258ca655b27b46e82657fd6f5 ]
Interrupts are enabled/disabled in more places than just m_can_start()
and m_can_stop(). Couple the polling timer with enabling/disabling of
all interrupts to achieve equivalent behavior.
Cc: Judith Mendez <jm@ti.com>
Fixes: b382380c0d2d ("can: m_can: Add hrtimer to generate software interrupt")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20240207093220.2681425-2-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 2aa0a5e65eae27dbd96faca92c84ecbf6f492d42 upstream.
The TDCO calculation was done using the currently applied data bittiming,
instead of the newly computed data bittiming, which means that the TDCO
had an invalid value unless setting the same data bittiming twice.
Fixes: d99755f71a80 ("can: netlink: add interface for CAN-FD Transmitter Delay Compensation (TDC)")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/40579c18-63c0-43a4-8d4c-f3a6c1c0b417@munic.io
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
accessed out of bounds
[ Upstream commit 6411959c10fe917288cbb1038886999148560057 ]
If the "struct can_priv::echoo_skb" is accessed out of bounds, this
would cause a kernel crash. Instead, issue a meaningful warning
message and return with an error.
Fixes: a6e4bc530403 ("can: make the number of echo skb's configurable")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-5-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
netif_carrier_on()
[ Upstream commit 6841cab8c4504835e4011689cbdb3351dec693fd ]
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fe5c9940dfd8ba0c73672dddb30acd1b7a11d4c7 ]
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4f8005092cafc194ba6a8e5f39626ba0b9f08271 ]
Fix below checkpatch warning:
WARNING: Missing a blank line after declarations
#2233: FILE: drivers/net/can/usb/etas_es58x/es58x_core.c:2233:
+ int ret = es58x_init_netdev(es58x_dev, ch_idx);
+ if (ret) {
Fixes: d8f26fd689dd ("can: etas_es58x: remove es58x_get_product_info()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230924110914.183898-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 107e6f6fe6f38577baecf0e01f517c8607a3a625 ]
Following [1], es58x_devlink.c now triggers the following
format-truncation GCC warnings:
drivers/net/can/usb/etas_es58x/es58x_devlink.c: In function ‘es58x_devlink_info_get’:
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:30: note: directive argument in the range [0, 255]
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:201:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
201 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
202 | fw_ver->major, fw_ver->minor, fw_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:41: warning: ‘%02u’ directive output may be truncated writing between 2 and 3 bytes into a region of size between 1 and 3 [-Wformat-truncation=]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:30: note: directive argument in the range [0, 255]
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:211:3: note: ‘snprintf’ output between 9 and 12 bytes into a destination of size 9
211 | snprintf(buf, sizeof(buf), "%02u.%02u.%02u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
212 | bl_ver->major, bl_ver->minor, bl_ver->revision);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:38: warning: ‘%03u’ directive output may be truncated writing between 3 and 5 bytes into a region of size between 2 and 4 [-Wformat-truncation=]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:30: note: directive argument in the range [0, 65535]
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~
drivers/net/can/usb/etas_es58x/es58x_devlink.c:221:3: note: ‘snprintf’ output between 9 and 13 bytes into a destination of size 9
221 | snprintf(buf, sizeof(buf), "%c%03u/%03u",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
222 | hw_rev->letter, hw_rev->major, hw_rev->minor);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This is not an actual bug because the sscanf() parsing makes sure that
the u8 are only two digits long and the u16 only three digits long.
Thus below declaration:
char buf[max(sizeof("xx.xx.xx"), sizeof("axxx/xxx"))];
allocates just what is needed to represent either of the versions.
This warning was known but ignored because, at the time of writing,
-Wformat-truncation was not present in the kernel, not even at W=3 [2].
One way to silence this warning is to check the range of all sub
version numbers are valid: [0, 99] for u8 and range [0, 999] for u16.
The module already has a logic which considers that when all the sub
version numbers are zero, the version number is not set. Note that not
having access to the device specification, this was an arbitrary
decision. This logic can thus be removed in favor of global check that
would cover both cases:
- the version number is not set (parsing failed)
- the version number is not valid (paranoiac check to please gcc)
Before starting to parse the product info string, set the version
sub-numbers to the maximum unsigned integer thus violating the
definitions of struct es58x_sw_version or struct es58x_hw_revision.
Then, rework the es58x_sw_version_is_set() and
es58x_hw_revision_is_set() functions: remove the check that the
sub-numbers are non zero and replace it by a check that they fit in
the expected number of digits. This done, rename the functions to
reflect the change and rewrite the documentation. While doing so, also
add a description of the return value.
Finally, the previous version only checked that
&es58x_hw_revision.letter was not the null character. Replace this
check by an alphanumeric character check to make sure that we never
return a special character or a non-printable one and update the
documentation of struct es58x_hw_revision accordingly.
All those extra checks are paranoid but have the merit to silence the
newly introduced W=1 format-truncation warning [1].
[1] commit 6d4ab2e97dcf ("extrawarn: enable format and stringop overflow warnings in W=1")
Link: https://git.kernel.org/torvalds/c/6d4ab2e97dcf
[2] https://lore.kernel.org/all/CAMZ6Rq+K+6gbaZ35SOJcR9qQaTJ7KR0jW=XoDKFkobjhj8CHhw@mail.gmail.com/
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Closes: https://lore.kernel.org/linux-can/20230914-carrousel-wrecker-720a08e173e9-mkl@pengutronix.de/
Fixes: 9f06631c3f1f ("can: etas_es58x: export product information through devlink_ops::info_get()")
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20230924110914.183898-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
IMX93 A0 chip involve the internal q-channel handshake in LPCG and
CCM to automatically handle the Flex-CAN IPG STOP signal. Only after
FLEX-CAN enter stop mode then can support the self-wakeup feature.
But meet issue when do the continue system PM stress test. When config
the CAN as wakeup source, the first time after system suspend, any data
on CAN bus can wakeup the system, this is as expect. But the second time
when system suspend, data on CAN bus can't wakeup the system. If continue
this test, we find in odd time system enter suspend, CAN can wakeup the
system, but in even number system enter suspend, CAN can't wakeup the
system. IC find a bug in the auto stop mode logic, and can't fix it easily.
So for the new imx93 A1, IC drop the auto stop mode and involve the
GPR to support stop mode (used before). IC define a bit in GPR which can
trigger the IPG STOP signal to Flex-CAN, let it go into stop mode.
And NXP claim to drop IMX93 A0, and only support IMX93 A1. So this patch
remove the auto stop mode, and add flag FLEXCAN_QUIRK_SETUP_STOP_MODE_GPR
to imx93.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/all/20230726112458.3524165-2-haibo.chen@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix id2_register content for tcan4553. This slipped through my testing.
Reported-by: Sean Anderson <sean.anderson@seco.com>
Closes: https://lore.kernel.org/lkml/a94e6fc8-4f08-7877-2ba0-29b9c2780136@seco.com/
Fixes: 142c6dc6d9d7 ("can: tcan4x5x: Add support for tcan4552/4553")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20230919095401.1312259-1-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upstream commit 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with
a soft reset on Renesas SoCs") fixes an issue with Renesas own SJA1000
CAN controller reception: the Rx buffer is only 5 messages long, so when
the bus loaded (eg. a message every 50us), overrun may easily
happen. Upon an overrun situation, due to a possible internal crosstalk
situation, the controller enters a frozen state which only can be
unlocked with a soft reset (experimentally). The solution was to offload
a call to sja1000_start() in a threaded handler. This needs to happen in
process context as this operation requires to sleep. sja1000_start()
basically enters "reset mode", performs a proper software reset and
returns back into "normal mode".
Since this fix was introduced, we no longer observe any stalls in
reception. However it was sporadically observed that the transmit path
would now freeze. Further investigation blamed the fix mentioned above,
and especially the reset operation. Reproducing the reset in a loop
helped identifying what could possibly go wrong. The sja1000 is a single
Tx queue device, which leverages the netdev helpers to process one Tx
message at a time. The logic is: the queue is stopped, the message sent
to the transceiver, once properly transmitted the controller sets a
status bit which triggers an interrupt, in the interrupt handler the
transmission status is checked and the queue woken up. Unfortunately, if
an overrun happens, we might perform the soft reset precisely between
the transmission of the buffer to the transceiver and the advent of the
transmission status bit. We would then stop the transmission operation
without re-enabling the queue, leading to all further transmissions to
be ignored.
The reset interrupt can only happen while the device is "open", and
after a reset we anyway want to resume normal operations, no matter if a
packet to transmit got dropped in the process, so we shall wake up the
queue. Restarting the device and waking-up the queue is exactly what
sja1000_set_mode(CAN_MODE_START) does. In order to be consistent about
the queue state, we must acquire a lock both in the reset handler and in
the transmit path to ensure serialization of both operations. It turns
out, a lock is already held when entering the transmit path, so we can
just acquire/release it as well with the regular net helpers inside the
threaded interrupt handler and this way we should be safe. As the
reset handler might still be called after the transmission of a frame to
the transceiver but before it actually gets transmitted, we must ensure
we don't leak the skb, so we free it (the behavior is consistent, no
matter if there was an skb on the stack or not).
Fixes: 717c6ec241b5 ("can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/all/20231002160206.190953-1-miquel.raynal@bootlin.com
[mkl: fixed call to can_free_echo_skb()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When adding the RISCV option I didn't gate it behind ARCH_SUNXI.
As a result this option shows up with Allwinner support isn't enabled.
Fix that by requiring ARCH_SUNXI to be set if RISCV is set.
Fixes: 8abb95250ae6 ("can: sun4i_can: Add support for the Allwinner D1")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/linux-sunxi/CAMuHMdV2m54UAH0X2dG7stEg=grFihrdsz4+o7=_DpBMhjTbkw@mail.gmail.com/
Signed-off-by: John Watts <contact@jookia.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/all/20230905231342.2042759-2-contact@jookia.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/net/inet_sock.h
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
c274af224269 ("inet: introduce inet->inet_flags")
https://lore.kernel.org/all/679ddff6-db6e-4ff6-b177-574e90d0103d@tessares.net/
Adjacent changes:
drivers/net/bonding/bond_alb.c
e74216b8def3 ("bonding: fix macvlan over alb bond support")
f11e5bd159b0 ("bonding: support balance-alb with openvswitch")
drivers/net/ethernet/broadcom/bgmac.c
d6499f0b7c7c ("net: bgmac: Return PTR_ERR() for fixed_phy_register()")
23a14488ea58 ("net: bgmac: Fix return value check for fixed_phy_register()")
drivers/net/ethernet/broadcom/genet/bcmmii.c
32bbe64a1386 ("net: bcmgenet: Fix return value check for fixed_phy_register()")
acf50d1adbf4 ("net: bcmgenet: Return PTR_ERR() for fixed_phy_register()")
net/sctp/socket.c
f866fbc842de ("ipv4: fix data-races around inet->inet_id")
b09bde5c3554 ("inet: move inet->mc_loop to inet->inet_frags")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
veth and vxcan need to make sure the ifindexes of the peer
are not negative, core does not validate this.
Using iproute2 with user-space-level checking removed:
Before:
# ./ip link add index 10 type veth peer index -1
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:74:b2:03 brd ff:ff:ff:ff:ff:ff
10: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 8a:90:ff:57:6d:5d brd ff:ff:ff:ff:ff:ff
-1: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:ed:18:e6:fa:7f brd ff:ff:ff:ff:ff:ff
Now:
$ ./ip link add index 10 type veth peer index -1
Error: ifindex can't be negative.
This problem surfaced in net-next because an explicit WARN()
was added, the root cause is older.
Fixes: e6f8f1a739b6 ("veth: Allow to create peer link with given ifindex")
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)")
Reported-by: syzbot+5ba06978f34abb058571@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes all those 'char's an explicit 'u8'. This is part of the
continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf().
Note that we do not change signedness as we compile with
-funsigned-char.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-18-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This makes all those 'unsigned char's an explicit 'u8'. This is part of
the continuing unification of chars and flags to be consistent u8.
This approaches tty_port_default_receive_buf(). Flags to be next.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-17-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Count passed to tty_ldisc_ops::receive_buf*(), ::lookahead_buf(), and
returned from ::receive_buf2() is expected to be size_t. So set it to
size_t to unify with the rest of the code.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@reisers.ca>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Andreas Koensgen <ajk@comnets.uni-bremen.de>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Matt Johnston <matt@codeconstruct.com.au>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-16-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'count' is going to be unsigned and the 'count >= 0' test would be
always true then. Move the condition to the loop where this is easier to
check.
It looks as is easier to follow after all too.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Link: https://lore.kernel.org/r/20230810091510.13006-15-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create a label with can327_uart_side_failure() and spin unlock. And jump
there from all three fail paths.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Link: https://lore.kernel.org/r/20230810091510.13006-14-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tty->disc_data is 'void *', so there is no need to cast from that.
Therefore remove the casts and assign the pointer directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Max Staudt <max@enpas.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Max Staudt <max@enpas.org>
Link: https://lore.kernel.org/r/20230801062237.2687-2-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for esd CAN-USB/3 and CAN FD to esd_usb.c.
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/all/20230728150857.2374886-2-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/all/20230802030900.2271322-1-ruanjinjie@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
tty->disc_data is 'void *', so there is no need to cast from that.
Therefore remove the casts and assign the pointer directly.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230731080244.2698-6-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To be able to understand issues during probe easier, add error messages
if something fails.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20230728141923.162477-7-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
tcan4552 and tcan4553 do not have wake or state pins, so they are
currently not compatible with the generic driver. The generic driver
uses tcan4x5x_disable_state() and tcan4x5x_disable_wake() if the gpios
are not defined. These functions use register bits that are not
available in tcan4552/4553.
This patch adds support by introducing version information to reflect if
the chip has wake and state pins. Also the version is now checked.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20230728141923.162477-6-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The datasheet calls these registers ID1 and ID2. Rename these to avoid
confusion.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-5-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
To reduce debugging effort in case the mram is misconfigured, add this
size check of the DT configuration. Currently if the mram configuration
doesn't fit into the available MRAM it just overwrites other areas of
the MRAM.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-4-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mentioned register is not writable. It is reserved and should not be
written.
Fixes: 39dbb21b6a29 ("can: tcan4x5x: Specify separate read/write ranges")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/all/20230728141923.162477-3-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no possible for platform_get_irq() to return 0
and the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/all/20230731075252.359965-1-ruanjinjie@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
We need the serial/tty fixes in here as well for testing and future
development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move PCI Vendor and Device ID of ASIX AX99100 PCIe to Multi I/O
Controller to pci_ids.h for its serial and parallel port driver
support in subsequent patches.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230724083933.3173513-3-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PCI_SUBVENDOR_ID_ASIX is defined as 0xa000, which is not the vendor id
assigned to ASIX by PCI-SIG. Remove it to avoid possible confusion and
conflict.
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20230724083933.3173513-2-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver used to pass received CAN frames/skbs to the network stack
with netif_rx(). In netif_rx() the skbs are queued to the local CPU.
If IRQs are handled in round robin, OoO packets may occur.
To avoid out-of-order reception convert the driver from netif_rx() to
NAPI.
For USB devices with timestamping support use the rx-offload helper
can_rx_offload_queue_timestamp() for the RX, and
can_rx_offload_get_echo_skb_queue_timestamp() for the TX path. Devices
without timestamping support use can_rx_offload_queue_tail() for RX,
and can_rx_offload_get_echo_skb_queue_tail() for the TX path.
Link: https://lore.kernel.org/all/559D628C.5020100@hartkopp.net
Link: https://github.com/candle-usb/candleLight_fw/issues/166
Link: https://lore.kernel.org/all/20230718-gs_usb-rx-offload-v2-3-716e542d14d5@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
