summaryrefslogtreecommitdiff
path: root/drivers/net/can/sja1000
AgeCommit message (Collapse)Author
2023-06-22can: sja1000: Prevent overrun stalls with a soft reset on Renesas SoCsMiquel Raynal
In their RZN1 SoC, Renesas put a CAN controller supposed to act very similarly to the original Philips sja1000. In practice, while flooding the bus with another device, we discovered that the controller very often after an overrun situation would just refuse any new frame, drop them all and trigger over and over again the overrun interrupt, even though the buffer would have been totally emptied. The controller acts like if its internal buffer offsets (where it writes and where the host reads) where totally screwed-up. Renesas manual mentions a single action to perform in order to resynchronize the read and write offsets within the buffer: performing a soft reset. Performing a soft reset takes a bit of time and involves small delays, so better do that in a threaded handler rather than inside the hard IRQ handler. Add platform data to recognize the platforms which need this workaround, and when the faulty situation is diagnosed, stop what is being performed and request the threaded handler to be executed in order to perform the reset. Tested-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com> # 5.10 Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/all/20230616134553.2786391-2-miquel.raynal@bootlin.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-06-22can: sja1000: Prepare the use of a threaded handlerMiquel Raynal
In order to support a flavor of the sja1000 which sometimes freezes, it will be needed upon certain interrupts to perform a soft reset. The soft reset operation takes a bit of time, so better not do it within the hard interrupt handler but rather in a threaded handler. Let's prepare the possibility for sja1000_err() to request "interrupting" the current flow and request the threaded handler to be run while keeping the interrupt line low. There is no functional change. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/all/20230616134553.2786391-1-miquel.raynal@bootlin.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: sja1000_platform: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230512212725.143824-16-u.kleine-koenig@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-05-15can: sja1000_isa: Convert to platform remove callback returning voidUwe Kleine-König
The .remove() callback for a platform driver returns an int which makes many driver authors wrongly assume it's possible to do error handling by returning an error code. However the value returned is ignored (apart from emitting a warning) and this typically results in resource leaks. To improve here there is a quest to make the remove callback return void. In the first step of this quest all drivers are converted to .remove_new() which already returns void. Eventually after all drivers are converted, .remove_new() is renamed to .remove(). Trivially convert this driver from always returning zero in the remove callback to the void returning variant. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230512212725.143824-15-u.kleine-koenig@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Add myself as module authorGerhard Uttenthaler
Added myself as module author Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-9-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Deassert hardware resetGerhard Uttenthaler
The reset line from the Asix chip to the SJA1000 is asserted after boot up until it is deasserted by a register write Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-8-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Add IRQ enableGerhard Uttenthaler
Add IRQ enable Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-7-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Initialize CAN controller base addressesGerhard Uttenthaler
Add CAN controller base registers Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-6-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Add read/write register and post irq functionsGerhard Uttenthaler
Add functions to read and write SJA1000 registers and also the post irq routine Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-5-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Initialize BAR registersGerhard Uttenthaler
Fix the base register defines and their usage for all three card versions Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-4-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Add Asix AX99100 definitionsGerhard Uttenthaler
Add Asix AX99100 PCI IDs and add the v3 to the ems_pci_tbl. Add define for maximum CAN channel count Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-3-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2023-02-02can: ems_pci: Fix code style, copyright and email addressGerhard Uttenthaler
Fix code style complained by checkpatch.pl, add Copyright and fix email address Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Link: https://lore.kernel.org/all/20230120112616.6071-2-uttenthaler@ems-wuensche.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-11-24can: sja1000_isa: sja1000_isa_probe(): add missing free_sja1000dev()Zhang Changzhong
Add the missing free_sja1000dev() before return from sja1000_isa_probe() in the register_sja1000dev() error handling case. In addition, remove blanks before goto labels. Fixes: 2a6ba39ad6a2 ("can: sja1000: legacy SJA1000 ISA bus driver") Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Link: https://lore.kernel.org/all/1668168521-5540-1-git-send-email-zhangchangzhong@huawei.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-11-07can: dev: fix skb drop checkOliver Hartkopp
In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") the priv->ctrlmode element is read even on virtual CAN interfaces that do not create the struct can_priv at startup. This out-of-bounds read may lead to CAN frame drops for virtual CAN interfaces like vcan and vxcan. This patch mainly reverts the original commit and adds a new helper for CAN interface drivers that provide the required information in struct can_priv. Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode") Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com> Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Cc: Max Staudt <max@enpas.org> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org # 6.0.x [mkl: patch pch_can, too] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-09-05can: sja1000: remove redundant variable retJinpeng Cui
Return value directly from register_candev() instead of getting value from redundant variable ret. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn> Link: https://lore.kernel.org/all/20220831161835.306079-1-cui.jinpeng2@zte.com.cn Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-09-05can: sja1000: Add support for RZ/N1 SJA1000 CAN ControllerBiju Das
The SJA1000 CAN controller on RZ/N1 SoC has no clock divider register (CDR) support compared to others. This patch adds support for RZ/N1 SJA1000 CAN Controller, by adding SoC specific compatible to handle this difference as well as using clk framework to retrieve the CAN clock frequency. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20220710115248.190280-7-biju.das.jz@bp.renesas.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-08-31net: move from strlcpy with unused retval to strscpyWolfram Sang
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN Link: https://lore.kernel.org/r/20220830201457.7984-1-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-07-28can: tree-wide: advertise software timestamping capabilitiesVincent Mailhol
Currently, some CAN drivers support hardware timestamping, some do not. But userland has no method to query which features are supported (aside maybe of getting RX messages and observe whether or not hardware timestamps stay at zero). The canonical way for a network driver to advertised what kind of timestamping it supports is to implement ethtool_ops::get_ts_info(). This patch only targets the CAN drivers which *do not* support hardware timestamping. For each of those CAN drivers, implement the get_ts_info() using the generic ethtool_op_get_ts_info(). This way, userland can do: | $ ethtool --show-time-stamping canX to confirm the device timestamping capacities. N.B. the drivers which support hardware timestamping will be migrated in separate patches. Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr [mkl: mscan: add missing mscan_ethtool_ops] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-20can: add CAN_ERR_CNT flag to notify availability of error counterVincent Mailhol
Add a dedicated flag in uapi/linux/can/error.h to notify the userland that fields data[6] and data[7] of the CAN error frame were respectively populated with the tx and rx error counters. For all driver tree-wide, set up this flags whenever needed. Link: https://lore.kernel.org/all/20220719143550.3681-12-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-20can: sja1000: do not report txerr and rxerr during bus-offVincent Mailhol
During bus off, the error count is greater than 255 and can not fit in a u8. Fixes: 215db1856e83 ("can: sja1000: Consolidate and unify state change handling") Link: https://lore.kernel.org/all/20220719143550.3681-4-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-19can: sja1000: Change the return type as void for SoC specific initBiju Das
Change the return type as void for SoC specific init function as it always return 0. Link: https://lore.kernel.org/all/20220710115248.190280-6-biju.das.jz@bp.renesas.com Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-19can: sja1000: Use device_get_match_data to get device dataBiju Das
This patch replaces of_match_device->device_get_match_data to get pointer to device data. Link: https://lore.kernel.org/all/20220710115248.190280-5-biju.das.jz@bp.renesas.com Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-07-19can: sja1000: Add Quirk for RZ/N1 SJA1000 CAN controllerBiju Das
As per Chapter 6.5.16 of the RZ/N1 Peripheral Manual, The SJA1000 CAN controller does not support Clock Divider Register compared to the reference Philips SJA1000 device. This patch adds a device quirk to handle this difference. Link: https://lore.kernel.org/all/20220710115248.190280-4-biju.das.jz@bp.renesas.com Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-05-19can: can-dev: remove obsolete CAN LED supportOliver Hartkopp
Since commit 30f3b42147ba6f ("can: mark led trigger as broken") the CAN specific LED support was disabled and marked as BROKEN. As the common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work now the code can be removed as preparation for a CAN netdevice Kconfig rework. Link: https://lore.kernel.org/all/20220518154527.29046-1-socketcan@hartkopp.net Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> [mkl: remove led.h from MAINTAINERS] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-04-19can: Fix Links to Technologic Systems web resourcesKris Bahnsen
Technologic Systems has rebranded as embeddedTS with the current domain eventually going offline. Update web/doc URLs to correct resource locations. Link: https://lore.kernel.org/all/20220329201229.16279-1-kris@embeddedTS.com Signed-off-by: Kris Bahnsen <kris@embeddedTS.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-01-05can: do not increase tx_bytes statistics for RTR framesVincent Mailhol
The actual payload length of the CAN Remote Transmission Request (RTR) frames is always 0, i.e. no payload is transmitted on the wire. However, those RTR frames still use the DLC to indicate the length of the requested frame. As such, net_device_stats::tx_bytes should not be increased when sending RTR frames. The function can_get_echo_skb() already returns the correct length, even for RTR frames (c.f. [1]). However, for historical reasons, the drivers do not use can_get_echo_skb()'s return value and instead, most of them store a temporary length (or dlc) in some local structure or array. Using the return value of can_get_echo_skb() solves the issue. After doing this, such length/dlc fields become unused and so this patch does the adequate cleaning when needed. This patch fixes all the CAN drivers. Finally, can_get_echo_skb() is decorated with the __must_check attribute in order to force future drivers to correctly use its return value (else the compiler would emit a warning). [1] commit ed3320cec279 ("can: dev: __can_get_echo_skb(): fix real payload length return value for RTR frames") Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Yasushi SHOJI <yashi@spacecubics.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Stephane Grosjean <s.grosjean@peak-system.com> Cc: Andreas Larsson <andreas@gaisler.com> Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 [mkl: add conversion for grcan] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-01-05can: do not increase rx_bytes statistics for RTR framesVincent Mailhol
The actual payload length of the CAN Remote Transmission Request (RTR) frames is always 0, i.e. no payload is transmitted on the wire. However, those RTR frames still use the DLC to indicate the length of the requested frame. As such, net_device_stats::rx_bytes should not be increased for the RTR frames. This patch fixes all the CAN drivers. Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Yasushi SHOJI <yashi@spacecubics.com> Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com> Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Stephane Grosjean <s.grosjean@peak-system.com> Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-01-05can: do not increase rx statistics when generating a CAN rx error message frameVincent Mailhol
The CAN error message frames (i.e. error skb) are an interface specific to socket CAN. The payload of the CAN error message frames does not correspond to any actual data sent on the wire. Only an error flag and a delimiter are transmitted when an error occurs (c.f. ISO 11898-1 section 10.4.4.2 "Error flag"). For this reason, it makes no sense to increment the rx_packets and rx_bytes fields of struct net_device_stats because no actual payload were transmitted on the wire. This patch fixes all the CAN drivers. Link: https://lore.kernel.org/all/20211207121531.42941-2-mailhol.vincent@wanadoo.fr CC: Marc Kleine-Budde <mkl@pengutronix.de> CC: Nicolas Ferre <nicolas.ferre@microchip.com> CC: Alexandre Belloni <alexandre.belloni@bootlin.com> CC: Ludovic Desroches <ludovic.desroches@microchip.com> CC: Chandrasekar Ramakrishnan <rcsekar@samsung.com> CC: Maxime Ripard <mripard@kernel.org> CC: Chen-Yu Tsai <wens@csie.org> CC: Jernej Skrabec <jernej.skrabec@gmail.com> CC: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com> CC: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com> CC: Michal Simek <michal.simek@xilinx.com> CC: Stephane Grosjean <s.grosjean@peak-system.com> Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2 Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2022-01-05can: sja1000: sp_probe(): use platform_get_irq() to get the interruptLad Prabhakar
It is preferred that drivers use platform_get_irq() instead of irq_of_parse_and_map(), so replace. Link: https://lore.kernel.org/all/20211221200016.13459-1-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-12-07can: sja1000: fix use after free in ems_pcmcia_add_card()Dan Carpenter
If the last channel is not available then "dev" is freed. Fortunately, we can just use "pdev->irq" instead. Also we should check if at least one channel was set up. Fixes: fd734c6f25ae ("can/sja1000: add driver for EMS PCMCIA card") Link: https://lore.kernel.org/all/20211124145041.GB13656@kili Cc: stable@vger.kernel.org Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-10-17can: peak_pci: peak_pci_remove(): fix UAFZheyu Ma
When remove the module peek_pci, referencing 'chan' again after releasing 'dev' will cause UAF. Fix this by releasing 'dev' later. The following log reveals it: [ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537 [ 35.965513 ] Call Trace: [ 35.965718 ] dump_stack_lvl+0xa8/0xd1 [ 35.966028 ] print_address_description+0x87/0x3b0 [ 35.966420 ] kasan_report+0x172/0x1c0 [ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170 [ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.967945 ] __asan_report_load8_noabort+0x14/0x20 [ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci] [ 35.968752 ] pci_device_remove+0xa9/0x250 Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards") Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-07-25can: peak_pci: Add name and FW version of the card in kernel bufferStephane Grosjean
This patch adds name and (possibly) firmware version information to the kernel about the detected PEAK-System CAN - PCI/PCIe interface card. Link: https://lore.kernel.org/r/20210607151720.13571-1-s.grosjean@peak-system.com Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com> [mkl: reformated struct pci_device_id peak_pci_tbl] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-07-25can: peak_pci: fix checkpatch warningsMarc Kleine-Budde
This patch cleans several checkpatch warnings in the peak_pci driver. Cc: Stephane Grosjean <s.grosjean@peak-system.com> Link: https://lore.kernel.org/r/20210616102811.2449426-0-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-07-25can: peak_pci: convert comments to network style commentsMarc Kleine-Budde
This patch converts all comments to network subsystem style comments. Cc: Stephane Grosjean <s.grosjean@peak-system.com> Link: https://lore.kernel.org/r/20210616102811.2449426-8-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-03-30can: dev: can_free_echo_skb(): extend to return can frame lengthMarc Kleine-Budde
In order to implement byte queue limits (bql) in CAN drivers, the length of the CAN frame needs to be passed into the networking stack even if the transmission failed for some reason. To avoid to calculate this length twice, extend can_free_echo_skb() to return that value. Convert all users of this function, too. This patch is the natural extension of commit: | 9420e1d495e2 ("can: dev: can_get_echo_skb(): extend to return can | frame length") Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-03-17module: remove never implemented MODULE_SUPPORTED_DEVICELeon Romanovsky
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was implemented. We can safely remove it, because the kernel has grown to have many more reliable mechanisms to determine if device is supported or not. Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2021-02-21Merge tag 'sound-5.12-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound updates from Takashi Iwai: "A relatively calm release at this time, and no massive code changes are found in the stats, while a wide range of code refactoring and cleanup have been done. Note that this update includes the tree-wide trivial changes for dropping the return value from ISA remove callbacks, too. Below lists up some highlight: ALSA Core: - Support for the software jack injection via debugfs - Fixes for sync_stop PCM operations HD-audio and USB-audio: - A few usual HD-audio device quirks - Updates for Tegra HD-audio - More quirks for Pioneer and other USB-audio devices - Stricter state checks at USB-audio disconnection ASoC: - Continued code refactoring, cleanup and fixes in ASoC core API - A KUnit testsuite for the topology code - Lots of ASoC Intel driver Realtek codec updates, quirk additions and fixes - Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro - Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers Others: - Drop return value from ISA driver remove callback - Cleanup with DIV_ROUND_UP() macro - FireWire updates, HDSP output loopback support" * tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits) ALSA: hda: intel-dsp-config: add Alder Lake support ASoC: soc-pcm: fix hw param limits calculation for multi-DAI ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet ASoC: soc-pcm: fix hwparams min/max init for dpcm ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10 ALSA: hda: Add another CometLake-H PCI ID ASoC: soc-pcm: add soc_pcm_hw_update_format() ASoC: soc-pcm: add soc_pcm_hw_update_chan() ASoC: soc-pcm: add soc_pcm_hw_update_rate() ASoC: wm_adsp: Remove unused control callback structure ASoC: SOF: relax ABI checks and avoid unnecessary warnings ASoC: codecs: lpass-tx-macro: add dapm widgets and route ASoC: codecs: lpass-tx-macro: add support for lpass tx macro ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec ASoC: codecs: lpass-rx-macro: add iir widgets ASoC: codecs: lpass-rx-macro: add dapm widgets and route ...
2021-01-26isa: Make the remove callback for isa drivers return voidUwe Kleine-König
The driver core ignores the return value of the remove callback, so don't give isa drivers the chance to provide a value. Adapt all isa_drivers with a remove callbacks accordingly; they all return 0 unconditionally anyhow. Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/ Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/ Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/ Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org> Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org Signed-off-by: Takashi Iwai <tiwai@suse.de>
2021-01-14can: dev: can_get_echo_skb(): extend to return can frame lengthMarc Kleine-Budde
In order to implement byte queue limits (bql) in CAN drivers, the length of the CAN frame needs to be passed into the networking stack after queueing and after transmission completion. To avoid to calculate this length twice, extend can_get_echo_skb() to return that value. Convert all users of this function, too. Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/r/20210111141930.693847-14-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2021-01-14can: dev: can_put_echo_skb(): extend to handle frame_lenVincent Mailhol
Add a frame_len argument to can_put_echo_skb() which is used to save length of the CAN frame into field frame_len of struct can_skb_priv so that it can be later used after transmission completion. Convert all users of this function, too. Drivers which implement BQL call can_put_echo_skb() with the output of can_skb_get_frame_len(skb) and drivers which do not simply pass zero as an input (in the same way that NULL would be given to can_get_echo_skb()). This way, we have a nice symmetry between the two echo functions. Link: https://lore.kernel.org/r/20210111061335.39983-1-mailhol.vincent@wanadoo.fr Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://lore.kernel.org/r/20210111141930.693847-13-mkl@pengutronix.de Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
2020-12-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
Conflicts: drivers/net/ethernet/ibm/ibmvnic.c Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-30can: sja1000: sja1000_err(): don't count arbitration lose as an errorJeroen Hofstee
Losing arbitration is normal in a CAN-bus network, it means that a higher priority frame is being send and the pending message will be retried later. Hence most driver only increment arbitration_lost, but the sja1000 driver also incremeants tx_error, causing errors to be reported on a normal functioning CAN-bus. So stop counting them as errors. Fixes: 8935f57e68c4 ("can: sja1000: fix network statistics update") Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com> Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com [mkl: split into two seperate patches] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2020-11-20can: drivers: add len8_dlc support for various CAN adaptersOliver Hartkopp
Support the Classical CAN raw DLC functionality to send and receive DLC values from 9 .. 15 on various Classical CAN capable CAN network drivers: - sja1000 - gs_usb - pcan_usb - pcan_usb_fd - usb_8dev Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201111095923.2535-1-socketcan@hartkopp.net [mkl: usb_8dev: changed indention] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2020-11-20can: replace can_dlc as variable/element for payload lengthOliver Hartkopp
The naming of can_dlc as element of struct can_frame and also as variable name is misleading as it claims to be a 'data length CODE' but in reality it always was a plain data length. With the indroduction of a new 'len' element in struct can_frame we can now remove can_dlc as name and make clear which of the former uses was a plain length (-> 'len') or a data length code (-> 'dlc') value. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net [mkl: gs_usb: keep struct gs_host_frame::can_dlc as is] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2020-11-20can: rename get_can_dlc() macro with can_cc_dlc2len()Oliver Hartkopp
The get_can_dlc() macro is used to ensure the payload length information of the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN). Rename the macro and use the correct constant in preparation of the len/dlc cleanup for Classical CAN frames. Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2020-09-21can: drivers: fix spelling mistakesMarc Kleine-Budde
This patch fixes spelling erros found by "codespell" in the drivers/net/can subtree. Link: https://lore.kernel.org/r/20200915223527.1417033-6-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2020-08-23treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-06-14treewide: replace '---help---' in Kconfig files with 'help'Masahiro Yamada
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-01-06remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig
ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
2019-08-20can: peak_pci: Make structure peak_pciec_i2c_bit_ops constantNishka Dasgupta
Static structure peak_pciec_i2c_bit_ops, of type i2c_algo_bit_data, is not used except to be copied into another variable. Hence make it const to protect it from modification. Issue found with Coccinelle. Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
generated by cgit v1.2.3 (git 2.39.1) at 2025-08-03 09:00:01 +0000