| Age | Commit message (Collapse) | Author |
|---|
|
Set GL9767 SDR104's clock to 205MHz and enable SSC feature
depend on register 0x888 BIT(1).
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230609071441.451464-3-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for the GL9767 chipset. GL9767 supports
SD3 mode likes UHS-I SDR50, SDR104.
Enable MSI interrupt for GL9767. Some platform do not
support PCI INTx and devices can not work without
interrupt.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230609071441.451464-2-victorshihgli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CQHCI_SSC1 indicates to CQE the polling period to use when using periodic
SEND_QUEUE_STATUS(CMD13) polling.
Since MSDC CQE uses msdc_hclk as ITCFVAL, so driver should use hclk
frequency to get the actual time.
The default value 0x1000 that corresponds to 150us for MediaTek SoCs, let's
decrease it to 0x40 that corresponds to 2.35us, which can improve the
performance of some eMMC devices.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20230609101355.5220-2-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SPI doesn't have the usual PROG path we can check for error bits
after moving back to TRAN. Instead it holds the line LOW until
completion. We can then check if the card shows any errors or
is in IDLE state, indicating the line is no longer LOW because
the card was reset.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/55920f880c9742f486f64aa44e25508e@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bayhub SD host has hardware limitation:
1.The upper 32bit address is inhibited to be written at SD Host Register
[03E][13]=0 (32bits addressing) mode, is admitted to be written only at
SD Host Register [03E][13]=1 (64bits addressing) mode.
2.Because of above item#1, need to configure SD Host Register [03E][13] to
1(64bits addressing mode) before set 64bit ADMA system address's higher
32bits SD Host Register [05F~05C] if 64 bits addressing mode is used.
The hardware limitation is reasonable for below reasons:
1.Normal flow should set DMA working mode first, then do
DMA-transfer-related configuration, such as system address.
2.The hardware limitation may avoid the software to configure wrong higher
32bit address at 32bits addressing mode although it is redundant.
The change that set 32bits/64bits addressing mode before set ADMA address,
has no side-effect to other host IPs for below reason:
The setting order is reasonable and standard: DMA Mode setting first and
then DMA address setting. It meets all DMA setting sequence.
Signed-off-by: Chevron Li <chevron.li@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230523111114.18124-1-chevron_li@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The error checks in mmc_blk_add_debugfs() and mmc_blk_remove_debugfs()
are extraneous. Therefore, this patch removes all error checks from
both functions.
Additionally, mmc_blk_add_debugfs() has been changed to return void
instead of an integer value that was never used. This simplifies the
function and improves its clarity.
Signed-off-by: Yeqi Fu <asuk4.q@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230518101216.369970-1-asuk4.q@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When I boot a kukui-kodama board, I see an ugly warning in my kernel
log:
mtk-msdc 11240000.mmc: error -ENXIO: IRQ sdio_wakeup not found
It's pretty normal not to have an "sdio_wakeup" IRQ defined. In fact,
no device trees in mainline seem to have it. Let's use the
platform_get_irq_byname_optional() to avoid the error message.
Fixes: 527f36f5efa4 ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20230510064434.1.I935404c5396e6bf952e99bb7ffb744c6f7fd430b@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Rather than casting mmc_free_host to an incompatible function type,
provide a trivial wrapper with the correct signature for the use-case.
Reported by clang-16 with W=1:
.../meson-mx-sdhc-mmc.c:791:38: error: cast from 'void (*)(struct mmc_host *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
ret = devm_add_action_or_reset(dev, (void(*)(void *))mmc_free_host,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/device.h:265:38: note: expanded from macro 'devm_add_action_or_reset'
__devm_add_action_or_reset(release, action, data, #action)
^~~~~~
The same approach is taken in litex_mmc.c with the function
litex_mmc_free_host_wrapper(). There may be scope for consolidation.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230510-mmc-sdhci-msm-function-cast-v1-1-5ae634b24fbd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If the device is not read-only, then we will be printing an empty
whitespace before the newline, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230509194455.1791890-1-f.fainelli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_pltfm_remove() returned zero unconditionally. Make it return void
instead which makes its semantics a bit clearer.
Convert the drivers that use this function as .remove() callback to
.remove_new() which has the right prototype. This helps getting rid of
the platform_driver's remove callback that returns an int (which is
error prone). The other users didn't check the return value anyhow.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230505221506.1247424-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
A recent change to the OMAP driver making it use a dynamic GPIO
base created problems with some old OMAP1 board files, among
them Nokia 770, SX1 and also the OMAP2 Nokia n8x0.
Fix up all instances of GPIOs being used for the MMC driver
by pushing the handling of power, slot selection and MMC
"cover" into the driver as optional GPIOs.
This is maybe not the most perfect solution as the MMC
framework have some central handlers for some of the
stuff, but it at least makes the situtation better and
solves the immediate issue.
Fixes: 92bf78b33b0b ("gpio: omap: use dynamic allocation of base")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Chapter "5.3 Power-Up/Down Sequence" of WILC1000 [1] and WILC3000 [2]
states that CHIP_EN must be pulled HIGH first, RESETN second. Fix the
order of these signals in the driver.
Use the mmc_pwrseq_ops as driver data as the delay between signals is
specific to SDIO card type anyway.
[1] https://ww1.microchip.com/downloads/aemDocuments/documents/WSG/ProductDocuments/DataSheets/ATWILC1000-MR110XB-IEEE-802.11-b-g-n-Link-Controller-Module-DS70005326E.pdf
[2] https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/IEEE-802.11-b-g-n-Link-Controller-Module-with-Integrated-Bluetooth-5.0-DS70005327B.pdf
Fixes: b2832b96fcf5 ("mmc: pwrseq: sd8787: add support for wilc1000")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230513192352.479627-1-marex@denx.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
[ 126.980684] UBSAN: array-index-out-of-bounds in drivers/mmc/host/vub300.c:1719:12
[ 126.980709] index -1 is out of range for type 'u32 [4]'
[ 126.980729] CPU: 4 PID: 9 Comm: kworker/u16:0 Tainted: G E 6.3.0-rc4-mtk-local-202304272142 #1
[ 126.980754] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, BIOS BECFL357.86A.0081.2020.0504.1834 05/04/2020
[ 126.980770] Workqueue: kvub300c vub300_cmndwork_thread [vub300]
[ 126.980833] Call Trace:
[ 126.980845] <TASK>
[ 126.980860] dump_stack_lvl+0x48/0x70
[ 126.980895] dump_stack+0x10/0x20
[ 126.980916] ubsan_epilogue+0x9/0x40
[ 126.980944] __ubsan_handle_out_of_bounds+0x70/0x90
[ 126.980979] vub300_cmndwork_thread+0x58e7/0x5e10 [vub300]
[ 126.981018] ? _raw_spin_unlock+0x18/0x40
[ 126.981042] ? finish_task_switch+0x175/0x6f0
[ 126.981070] ? __switch_to+0x42e/0xda0
[ 126.981089] ? __switch_to_asm+0x3a/0x80
[ 126.981129] ? __pfx_vub300_cmndwork_thread+0x10/0x10 [vub300]
[ 126.981174] ? __kasan_check_read+0x11/0x20
[ 126.981204] process_one_work+0x7ee/0x13d0
[ 126.981246] worker_thread+0x53c/0x1240
[ 126.981291] kthread+0x2b8/0x370
[ 126.981312] ? __pfx_worker_thread+0x10/0x10
[ 126.981336] ? __pfx_kthread+0x10/0x10
[ 126.981359] ret_from_fork+0x29/0x50
[ 126.981400] </TASK>
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/048cd6972c50c33c2e8f81d5228fed928519918b.1683987673.git.deren.wu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate
ESDHC_FLAG_HS400* only on 8bit bus"), the property "no-mmc-hs400"
from device tree file do not work any more.
This patch reorder the code, which can avoid the warning message
"drop HS400 support since no 8-bit bus" and also make the property
"no-mmc-hs400" from dts file works.
Fixes: 1ed5c3b22fc7 ("mmc: sdhci-esdhc-imx: Propagate ESDHC_FLAG_HS400* only on 8bit bus")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230504112222.3599602-1-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If devm_reset_control_get_optional_exclusive() fails, some resources still
need to be released. So branch to the error handling path instead of
returning directly.
Fixes: aad53d4ee756 ("mmc: sdhci-cadence: Support mmc hardware reset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Brad Larson <blarson@amd.com>
Link: https://lore.kernel.org/r/f61599a9ef23767c2d66e5af9c975f05ef1cec6b.1682430069.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Requests to the mmc layer usually come through a block device IO.
The exceptions are the ioctl interface, RPMB chardev ioctl
and debugfs, which issue their own blk_mq requests through
blk_execute_rq and do not query the BLK_STS error but the
mmcblk-internal drv_op_result. This patch ensures that drv_op_result
defaults to an error and has to be overwritten by the operation
to be considered successful.
The behavior leads to a bug where the request never propagates
the error, e.g. by directly erroring out at mmc_blk_mq_issue_rq if
mmc_blk_part_switch fails. The ioctl caller of the rpmb chardev then
can never see an error (BLK_STS_IOERR, but drv_op_result is unchanged)
and thus may assume that their call executed successfully when it did not.
While always checking the blk_execute_rq return value would be
advised, let's eliminate the error by always setting
drv_op_result as -EIO to be overwritten on success (or other error)
Fixes: 614f0388f580 ("mmc: block: move single ioctl() commands to block requests")
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/59c17ada35664b818b7bd83752119b2d@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver updates for 6.4-rc1.
Nothing major, just lots of tiny, constant, forward development. This
includes:
- obligatory n_gsm updates and feature additions
- 8250_em driver updates
- sh-sci driver updates
- dts cleanups and updates
- general cleanups and improvements by Ilpo and Jiri
- other small serial driver core fixes and driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (87 commits)
n_gsm: Use array_index_nospec() with index that comes from userspace
tty: vt: drop checks for undefined VT_SINGLE_DRIVER
tty: vt: distribute EXPORT_SYMBOL()
tty: vt: simplify some cases in tioclinux()
tty: vt: reformat tioclinux()
tty: serial: sh-sci: Fix end of transmission on SCI
tty: serial: sh-sci: Add support for tx end interrupt handling
tty: serial: sh-sci: Fix TE setting on SCI IP
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA rx support
tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support
serial: max310x: fix IO data corruption in batched operations
serial: core: Disable uart_start() on uart_remove_one_port()
serial: 8250: Reinit port->pm on port specific driver unbind
serial: 8250: Add missing wakeup event reporting
tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
tty: serial: fsl_lpuart: adjust buffer length to the intended size
serial: fix TIOCSRS485 locking
serial: make SiFive serial drivers depend on ARCH_ symbols
tty: synclink_gt: don't allocate and pass dummy flags
tty: serial: simplify qcom_geni_serial_send_chunk_fifo()
...
|
|
The function sched_partition_show cannot execute return, delete the
invalid code.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Link: https://lore.kernel.org/r/20230412084758.2673-1-liubo03@inspur.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for mmc hardware reset using a reset-controller
that would need to be enabled in the device tree with
a supporting driver. The default is disabled for all
existing designs.
Signed-off-by: Brad Larson <blarson@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20230410184526.15990-15-blarson@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for AMD Pensando Elba SoC which explicitly
controls byte-lane enables on writes.
Select MMC_SDHCI_IO_ACCESSORS for MMC_SDHCI_CADENCE which
allows Elba SoC sdhci_elba_ops to overwrite the SDHCI
IO memory accessors
Signed-off-by: Brad Larson <blarson@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230410184526.15990-14-blarson@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Move struct sdhci_pltfm_data under new struct sdhci_cdns_drv_data.
Add an init() into sdhci_cdns_drv_data for platform specific device
initialization in the device probe which is not used for existing devices.
Signed-off-by: Brad Larson <blarson@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230410184526.15990-13-blarson@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SoCs with device specific Cadence implementation, such as setting
byte-enables before the write, need to override writel(). Add a
callback where the default is writel() for all existing chips.
Signed-off-by: Brad Larson <blarson@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230410184526.15990-12-blarson@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is no user for macro mmc_req_rel_wr, so delete it.
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20230403221754.16168-1-beanhuo@iokpp.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Clock delay settings are not defined for 400KHz, so add frequency check
to skip calling the clock delay settings when frequency is <=400KHz.
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230403102551.3763054-4-sai.krishna.potthuri@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for eMMC5.1 on Xilinx Versal Net platform
- Add new compatible string(xlnx,versal-net-emmc).
- Add support for PHY which is part of Host Controller register space.
- Add DLL and Delay Chain mode support and corresponding tap delays for
all eMMC modes.
- Add Strobe select tap for HS400 mode.
Signed-off-by: Swati Agarwal <swati.agarwal@amd.com>
Co-developed-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Signed-off-by: Sai Krishna Potthuri <sai.krishna.potthuri@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230403102551.3763054-3-sai.krishna.potthuri@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support for suspend/resume and pm_runtime resume/suspend.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230331101619.4117312-1-vigneshr@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pointer variables of void * type do not require type cast.
Signed-off-by: Yu Zhe <yuzhe@nfschina.com>
Link: https://lore.kernel.org/r/20230328031049.22749-1-yuzhe@nfschina.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Merge the mmc fixes for v6.3-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.4.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If spec_reg is equal to 'SDHCI_PRESENT_STATE', esdhc_readl_fixup()
fixes up register value and returns it immediately. As a result, the
further block
(spec_reg == SDHCI_PRESENT_STATE)
&&(esdhc->quirk_ignore_data_inhibit == true),
is never executed.
The patch merges the second block into the first one.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f1929f3f2fa ("mmc: sdhci-of-esdhc: add quirk to ignore command inhibit for data")
Signed-off-by: Georgii Kruglov <georgy.kruglov@yandex.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230321203715.3975-1-georgy.kruglov@yandex.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Failing to detect a non-removable card shouldn't happen. Let's log a
message about it to inform that we have problem that ought to be fixed.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Link: https://lore.kernel.org/r/d2444591-c91b-a94d-71e2-9dedc3b6c514@free.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
clang with W=1 reports
drivers/mmc/host/sdricoh_cs.c:104:28: error: unused function
'sdricoh_readw' [-Werror,-Wunused-function]
static inline unsigned int sdricoh_readw(struct sdricoh_host *host,
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230319164744.1707169-1-trix@redhat.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove Thunder Bay specific code as the product got cancelled
and there are no end customers or users.
Signed-off-by: A, Rashmi <rashmi.a@intel.com>
Reviewed-by: Hunter, Adrian <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230316120549.21486-2-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Timing Information in Datasheet assumes that HIGH_SPEED_ENA=1 should be
set for SDR12 and SDR25 modes. But sdhci_am654 driver clears
HIGH_SPEED_ENA register. Thus, Modify sdhci_am654 to not clear
HIGH_SPEED_ENA (HOST_CONTROL[2]) bit for SDR12 and SDR25 speed modes.
Fixes: e374e87538f4 ("mmc: sdhci_am654: Clear HISPD_ENA in some lower speed modes")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230317092711.660897-1-b-kapoor@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230315055355.66733-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230315055023.61779-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20230315054113.48898-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230315053434.38316-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230315053127.33855-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to commit 890cc39a8799 ("drivers: provide
devm_platform_get_and_ioremap_resource()"), convert
platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230315052231.21212-1-yang.lee@linux.alibaba.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci_get_compatibility() uses OF functions which have stubs for !OF
case, thus entire CONFIG_OF ifdef can be dropped. This also fixes
!CONFIG_OF W=1 warning:
drivers/mmc/host/sdhci-pltfm.c:76:6: error: no previous prototype for ‘sdhci_get_compatibility’ [-Werror=missing-prototypes]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230314203901.20803-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use new helpers mmc_regulator_enable/disable_vqmmc to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/2ceb62da-07e6-bafc-c29e-13cc1cdde93a@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There's a number of drivers (e.g. dw_mmc, meson-gx, mmci, sunxi) using
the same mechanism and a private flag vqmmc_enabled to deal with
enabling/disabling the vqmmc regulator.
Move this to the core and create new helpers mmc_regulator_enable_vqmmc
and mmc_regulator_disable_vqmmc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/71586432-360f-9b92-17f6-b05a8a971bc2@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After 087592395a96 ("mmc: core: Allow invalid regulator in
mmc_regulator_set_ocr()") we can remove the checks here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/858a592b-ebf4-99b4-74fc-21b4ad3382f8@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Change SDR50 mode clock source from DLL output clock to PLL open clock
1.HS200 and SDR104 mode select DLL output clock
2.SDR50 mode select PLL open clock
Signed-off-by: Fred <fred.ai@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230223120450.16858-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144715.1543836-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144714.1543767-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently .get_max_clock returns the current clock rate for cclk_emmc
on rk35xx, thus max clock gets set to whatever bootloader set it to.
In case of u-boot, it is intentionally reset to 50 MHz if it boots
from eMMC, see mmc_deinit() in u-boot sources. As a result, HS200 and
HS400 modes are never selected by Linux, because dwcmshc_rk35xx_postinit
clears appropriate caps if host->mmc->f_max is < 52MHz
cclk_emmc is not a fixed clock on rk35xx, so using
sdhci_pltfm_clk_get_max_clock is not appropriate here.
Implement rk35xx_get_max_clock that returns actual max clock for cclk_emmc.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230310010349.509132-1-anarsoul@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20230307163041.3815-9-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Basically all host drivers use code like this:
if (!IS_ERR(mmc->supply.vmmc))
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0)
Move the IS_ERR() check to mmc_regulator_set_ocr() to simplify host driver
code.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/0c1e7440-f4bc-b48a-137f-58b75ac98550@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add support to read the optional "gate" clock property and request the
clock which will be used to ungate the DLL clock.
For Xilinx platforms which has DLL module, dll clock must be
ungated/enabled when SD controller operates at higher frequencies like 50
MHz, 100 MHz and 200 MHz. This will be done by explicitly requesting gate
clock from the driver.
Signed-off-by: Swati Agarwal <swati.agarwal@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230223141402.23979-1-swati.agarwal@amd.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
